SterlingメーカーSDAA 25-100の使用説明書/サービス説明書
ページ先へ移動 of 60
SDAA 25-100 (15-60 cfm) Dehumidifying Dryers Part Number: 882.00290.0 0 Bulletin Number: DH1-640 Effective: 12/06/05 Write Down Your Serial Numbers Here For Future Reference: _________________________.
Shipping Information Unpacking and Inspection You should inspect your dryer for possible shipping damage. Thoroughly check the equipment for any dam age th at might have occurred in transit, such as broken or loose wiring and components, l oose hardware and mounting screws, etc.
Dehumidifying Dryers ii Table of Contents CHAPTER 1: SAFETY ................................................................ V 1-1 How to Use This Manual ............................................................................................. v Safety Symbols Used in this Manual .
Dehumidifying Dryers iii Restoring the Process Air Temperature Controller (E5CN) to Factory Settings.. 28 Process Air Dew Point Display ............................................................................ 31 Setting the High Dew Point Alarm ..
Dehumidifying Dryers iv Service Department ............................................................................................. 59 Sales Department ..............................................................................................
Dehumidifying Dryers Chapter 1: Safety v of 59 Chapter 1: Safety 1-1 How to Use This Manual Use this manual as a guide and reference for installing, operating, and maintaining your dehumidifying dryer. The purpose is to assist you in applying effici ent, proven techniques that enhance equipment productivity.
Dehumidifying Dryers Chapter 1: Safety vi 1-2 Warnings and Precautions Our equipment is designed to provide safe and reliable operation when installed and operated within design specifications, following national a nd local safety codes.
Dehumidifying Dryers Chapter 1: Safety vii 1-3 Responsibility These machines are constructed for maximum operator safety when used under standard operating conditions and when recommended inst ructions are followed in the maintenance and operation of the machine.
Dehumidifying Dryers Chapter 1: Safety viii Operator Responsibility The operator’s responsibility does not end with e fficient production. The operator usually has the most daily contact with the equipment and intimately knows its capabilities and limitations.
Dehumidifying Dryers Chapter 1: Safety ix • Clean the dryer and surrounding area DAILY , and inspect the machine for loose, missing or broken parts. • Shut off power to the dryer when it is not in use. T urn the switch to the OFF position, or unplug it from the power source.
Dehumidifying Dryers Chapter 1: Safety x.
Dehumidifying Dryers Chapter 2: Functional Description 11 of 59 Chapter 2: Functional Description 2-1 Models Covered in This Manual This manual provides operation, installation, and m aintenance instructions for 15, 30, and 60 cfm dehumidifying dryers.
Dehumidifying Dryers Chapter 2: Functional Description 12 of 59 A small amount of ambient air is introduced in to the process air stream to make up for the air lost during the bed regeneration. Because the process air is typically much drier than the ambient air, the air mixture maintains drying effici ency at a consistently high level.
Dehumidifying Dryers Chapter 2: Functional Description 13 of 59 • NFPA79 machinery electrical standards • Non-fused electrical disconnect • Branch fusing • Mercury process heater contactor •.
Dehumidifying Dryers Chapter 2: Functional Description 14 of 59 • Identify and locate specific safety devices. • Understand the proper use of the safety devices provided.
Dehumidifying Dryers Chapter 3: Installation 15 of 59 Chapter 3: Inst allation 3-1 Uncrating the Equipment Dehumidifying Dryers are shipped mounted on a skid, enclosed in a plastic wrapper, and contained in a cardboard box. 1. Pry the crating away from the skid.
Dehumidifying Dryers Chapter 3: Installation 16 of 59 Figure 16: Machine-Mount Dryer Dimensions 15, 30, 60 cfm mac hine-mount dimensions in inc hes/cm 15 cfm 30 cfm 60 cfm 0.7 ft. 3 /20 liters 1.5 ft. 3 /40 liters 1.5 ft. 3 /40 liters 3.0 ft. 3 /80 liters 4.
Dehumidifying Dryers Chapter 3: Installation 17 of 59 Figure 17: Floor-Mount Dryer Dimensions 15, 30, 60 cfm floor-mount dimension s in inches/cm 15 cfm 30 cfm 60 cfm Dimension in. cm in. cm in. cm A 20 51 20 51 24 61 B 32.5 83 32.5 83 32.5 83 C 30 76 30 76 30 76 D 30 76 30 76 34 86 E 23.
Dehumidifying Dryers Chapter 3: Installation 18 of 59 Figure 1: Suggested Lift Rigging for Cart Mounted Dryers Caution! Do not use a hoist to move or rig your Dryer when it is mounted on a cart! Movin.
Dehumidifying Dryers Chapter 3: Installation 19 of 59 Figure 3: Suggested Lift Rigging for Machine Mounted Dryers Caution! When using a hoist to move a machine mounted dryer, ALWAYS attach chains to t.
Dehumidifying Dryers Chapter 3: Installation 20 of 59 3-4 Setup Procedures This section provides the procedures necessary fo r configuring your Dehumidifying Dryer. Configuration of your dryer includes checking for pr oper blower rotation, making dryer/drying hopper process air connections and the optional aftercooler (on 60 cfm models).
Dehumidifying Dryers Chapter 3: Installation 21 of 59 Drying Hopper Air Trap Considerations Our exclusive air trap assembly on the top of the drying hopper prevents am bient air from contaminating the material being dried .
Dehumidifying Dryers Chapter 3: Installation 22 of 59 3-5 Initial Start-up Pre-Startup Checks ; Check the process and return hoses for tight connections. ; Check all companion equipment, such as the drying hopper; verif y that the loading system is ready for operation.
Dehumidifying Dryers Chapter 3: Installation 23 of 59 Shutting Down the Dryer 1. Turn off the conveying system supplying the drying hopper. 2. When processing is complete, close the hoppe r slide gate and shut down any in-line companion equipment, such as the aftercooler.
Dehumidifying Dryers Chapter 4: Operation 24 of 59 Chapter 4: Operation 4-1 Start-up 1. Turn on (energize) the disconnect switch in your power drop, then turn on the o ne on the dryer. 2. Turn the system ON/OFF switch to ON to energize the display panel.
Dehumidifying Dryers Chapter 4: Operation 25 of 59 4-2 Controller Description and Operation Identifying Control Panel Indicator Lights and Switches for the Standard Controller Switches System OFF/ON/START Switch. This switch energizes or de-energizes control power to the indicator panel and starts the dryer.
Dehumidifying Dryers Chapter 4: Operation 26 of 59 Process Air Temperature Controller Our dryers use a microprocessor-based PID temp erature controller for maintaining process air temperature. The controller is a modular, self-contained unit you c an remove from the mounting housing.
Dehumidifying Dryers Chapter 4: Operation 27 of 59 Indicator Name Description ALARM1 ALARM 1 LED Lights in the Operation Indicator Section when the output function assigned to auxiliary output 1 turns on. The ALARM1 indicator lights when the process temperature exceeds the set point temperature by more than the alarm deviation value.
Dehumidifying Dryers Chapter 4: Operation 28 of 59 Restoring the Process Air Temperature Controller (E5CN) to Factory Settings If the preset parameters on the controller have been tampered with and it no longer properly controls temperature and displays dew point, you can restore the controllers to the factory setup.
Dehumidifying Dryers Chapter 4: Operation 29 of 59 Adjustment Level Indicator Name Description Auto-Tune Mode (At) See Page 19 of Chapter 3 for instructions on how to Auto-Tune your dryer. Note: Although the controller is calibrated at the factory, the manufacturer recommends that the unit be Auto- Tuned prior to dryer startup.
Dehumidifying Dryers Chapter 4: Operation 30 of 59 Entering Operating Parameters to Select Modes To enter the display: 1. Press the Mode Display key to view the Run/Stop & Alarm 1 Modes. 2. Press and to set the higher or lower the values of the param eter or turn that function On or Off.
Dehumidifying Dryers Chapter 4: Operation 31 of 59 Process Air Dew Point Display Optional The Process Air Dew Point meter indicates the cu rrent process air delivery m oisture content. Standard dryers use a microprocessor-based controller for displaying dew point air temperature.
Dehumidifying Dryers Chapter 4: Operation 32 of 59 Redundant Safety Controller Display Optional The Redundant Safety Controller limits the pr ocess air temperature from exceeding the upper temperature range set by the E5CN Temperature Controller. Standard dryers use a microprocessor-based controller for limiting the process air temperature.
Dehumidifying Dryers Chapter 4: Operation 33 of 59 Entering Operating Parameters to Select Modes To enter the display: 1. Press both the Up and Down keys for three seconds from the home page. The word SEE will appear in the upper display and PAGE will appear in the lower display.
Dehumidifying Dryers Chapter 4: Operation 34 of 59 4-3 Dryer Operation Procedures Controller Operation (Without Optional Alarm Horn & Reset Button) 1. Turn the disconnect on the control panel to the ON position. Power is applied to the voltage line fuses, line side of the control power switch and the temperature controller.
Dehumidifying Dryers Chapter 4: Operation 35 of 59 3. Once the control power is on and no fa ult conditions exist, turning the OFF-ON- START switch to the START position will start the dryer as follows: a. The process heater is turned on and controlled by the E5CN controller.
Dehumidifying Dryers Chapter 4: Operation 36 of 59 11. When a dew point fault is generated by th e optional d ew point controller, the alarm light will activate. The alarm light will flash, indicating a non-critical fault. Press Alarm Reset to deactivate the alarm un til the next dew point fault oc curs.
Dehumidifying Dryers Chapter 4: Operation 37 of 59 Controller Operation (With Optional Alarm Horn & Reset Button) 1. Turn the disconnect on the control panel to the ON position. Power is applied to the voltage line fuses, line side of the control power switch and the temperature controller.
Dehumidifying Dryers Chapter 4: Operation 38 of 59 5. If the OMRON controller faults, the optional redundant high tem perature safety device opens, or the process heater safety switch opens, a process heater fault is generated. “HIGH TEMP” is displa yed on the relay screen.
Dehumidifying Dryers Chapter 4: Operation 39 of 59 Alarm Display Messages Note: The relay screen which contains the Alarm Display Messages is located inside the controller enclosure.
Dehumidifying Dryers Chapter 4: Operation 40 of 59 4-4 Auto-Tuning the Dryer 1. For Auto-tuning, press the beige button on ce. The AT screen will show with the setting OFF. 2. Press the UP arrow to change the setting to ON. 3. Press the beige button again to go back to the Temperature Screen.
Dehumidifying Dryers Chapter 5: Maintenance 41 of 59 Chapter 5: Maintenance 5-1 Preventative Maintenance Schedule The checklist below contains a list of items wh ich should be inspected and/or replaced to keep your Dehumidifying Dryer operating at peak efficiency.
Dehumidifying Dryers Chapter 5: Maintenance 42 of 59 5-2 Preventative Maintenance This section describes maintenance procedures which will increase the longevity and efficiency of your dehumidifying dryer. Perform them at the regular intervals listed on the dryer checklist on the previous page.
Dehumidifying Dryers Chapter 5: Maintenance 43 of 59 Cleaning with Compressed Air Blow clean, dry compressed air up and down the pleats, blowing out the filter from the inside out. Remove loose dirt fr om the filter with compressed air or vaccum from the outside.
Dehumidifying Dryers Chapter 5: Maintenance 44 of 59 Dew point sensor life depends on: • Air temperature and flow passing over the sensor. • The amount of fines (dust) in the process air.
Dehumidifying Dryers Chapter 5: Maintenance 45 of 59 WARNING! Handling desiccant material is HAZAR DOUS. Wear an N-100 type safety filter mask or equivalent to avoid prolonged breathing of desiccant dust. Wear safety goggles and gloves to avoid contact with eyes and skin.
Dehumidifying Dryers Chapter 5: Maintenance 46 of 59 Figure 11: Desiccant Bed Location and Disassembly Caution! You should properly dispose of any discarded desiccant. Consult local disposal regula tions for more information. Inspect each lower desiccant screen for tear s or holes where desiccant burned-through.
Dehumidifying Dryers Chapter 5: Maintenance 47 of 59 Replacing the Process Heater The dehumidifying dryers utilize a single-phase Ca lrod-type heater element.
Dehumidifying Dryers Chapter 6: Troubleshooting 48 of 59 Chapter 6: T roubleshooting 6-1 Introduction The utmost in safety precautions should be observed at all times when working on or around the machine and the electrical components.
Dehumidifying Dryers Chapter 6: Troubleshooting 49 of 59 Problem Possible cause Corrective action Process heaters are faulty. Check for open heaters. Replace if required. Solid-state temperature controller faulty. Replace. Loss or reduction of process air temperature.
Dehumidifying Dryers Chapter 6: Troubleshooting 50 of 59 Problem Possible cause Corrective action Process temperature set too high due to operator error. Check resin manufacturer’s data sheet for proper drying temperature. Make sure plant personnel are aware of the correct process temperature set point.
Dehumidifying Dryers Chapter 6: Troubleshooting 51 of 59 Problem Possible cause Corrective action No setting change possible on temperature controller. The key protection switch is set to ON . Set the key protection switch to OFF . Input polarity on thermo-couple is wrong or connection is wrong.
Dehumidifying Dryers Chapter 7: Appendix 52 of 59 Chapter 7: Appendix 7-1 Warranty Unless otherwise specified, this product includes a Standard ONE YE AR PARTS WARRANTY.
Dehumidifying Dryers Chapter 7: Appendix 53 of 59 Warranty Liabilities THE COMPANY EXPRESSLY DIS CLAIMS ANY AND ALL LIABILITY FOR ANY SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES OR EXPENSES THAT RESULT FROM THE USE OF THIS PRODUCT.
Dehumidifying Dryers Chapter 7: Appendix 54 of 59 7-3 Technical Specifications Annex B Information The following design information is provided for your reference: 1. No modifications are allowed to this equi pment that could alter the CE compliance 2.
Dehumidifying Dryers Chapter 7: Appendix 55 of 59 Aftercooler Design Specifications Entering water temp. ºF ºC 85ºF 29ºC 7-4 Drawings and Diagrams 7-5 Spare Parts List Figure 18: Level 1 Spare Par.
Dehumidifying Dryers Chapter 7: Appendix 56 of 59 Figure 19: Level 2 & 3 Spare Parts List (Electrical & Mechani cal) MINI DRY ER SPARE P ARTS LI ST AD15, AD30, AD60 15CFM 15CFM 15CFM 15CFM 15C.
Dehumidifying Dryers Chapter 7: Appendix 57 of 59 7-6 Returned Material Policy Credit Returns Prior to the return of any material authorization m ust be given by the manufacturer. A RMA number will be assigned for the equipment to be returned. Reason for requesting the return must be given.
Dehumidifying Dryers Chapter 7: Appendix 58 of 59 7-8 Dryer Identification (Serial Number) Tag (Located on back of Dryer) Company Logo XXX Series Dryer Model Number XXX-15 Max Drying Capacity HR 460V Serial Number 060701R 1 Ǿ Date of Manufac ture 06/2003 4.
Dehumidifying Dryers Chapter 7: Appendix 59 of 59 7-9 Technical Assistance Parts Department Call toll-free 7am–5pm CST [ 800 ] 423- 3183 or call [ 630 ] 595-1060, Fax [630] 475-7005 The ACS Customer.
デバイスSterling SDAA 25-100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sterling SDAA 25-100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSterling SDAA 25-100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sterling SDAA 25-100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sterling SDAA 25-100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sterling SDAA 25-100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSterling SDAA 25-100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sterling SDAA 25-100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSterling SDAA 25-100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
