SubaruメーカーH7110LS200の使用説明書/サービス説明書
ページ先へ移動 of 8
1 INST ALLA TION INSTR UCTIONS SECURITY SYSTEM UPGRADE LEGA CY P/N: H7110LS200 Kit Contents: 1 Security Control Module w/Integral Brack et 1 Starter Interrupt/Horn Relays w/Integral Brack et 1 Horn w/.
2 Figure 1 Figure 2 Figure 3 A. Pre-Installation Notes B. Security Module Installation 1. V ehicle Preparation a. Lo wer the driv er’ s side window to a void inadv ertently locking the keys in the v ehicle dur- ing installation. b . Disconnect negati ve battery terminal to pre vent accidental shorting of an y power circuits.
3 Figure 4 Figure 5 Figure 6 4. Lift the center console co ver by carefully pulling outward in areas indicated by arro ws in Figure 4. 5. Remove the six scre ws indicated by the arro ws in Figure 5. Do not disconnect any connectors. Pull the unit out just far enough to access the passenger side of the unit.
4 C. Starter Interrupt and Horn Relay Installation 1. Remov e the screw indicated by the arro w in Figure 1 and disengage the two plastic scre ws indicated by arro ws in Figure 2, then remov e the dash panel.
5 E. Prior to System T est W ARNING! Do not allow terminals of radio connectors to come in contact with any metal from vehicle due to +12 v olts being present at these terminals. 1. Reconnect negati ve battery terminal. D. Horn Installation 1. Locate the A T resistor in the engine compartment.
6 G. V alet Mode T est 1. Open the dri ver’ s door and then depress and hold the UNLOCK/DISARM button on the remote for more than two seconds and the follo wing should be observed: a. The status indicator (LED) will begin flashing 2x per second indicating that the alarm is in the v alet mode.
7 I. Notes on System Operation 1. If the alarm is not deacti vated within 30 seconds of triggering, the system will automatically reset. 2. The hood is not protected as a part of this system and therefore will not cause a triggering of the alarm when opened unless suf ficient force is used in which case the shock sensor will trig- ger the alarm.
8 K. Finishing the Installation 1. Re verse steps 1 through 10 in section B. Installation Preparation, to reassemble radio, radio trim bezel, cup holder , ashtray , gear shift cov er and parking brake trim. 2. Replace the lo wer dash panel below the steering column.
デバイスSubaru H7110LS200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Subaru H7110LS200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSubaru H7110LS200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Subaru H7110LS200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Subaru H7110LS200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Subaru H7110LS200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSubaru H7110LS200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Subaru H7110LS200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSubaru H7110LS200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。