BarcoメーカーR59770263/06の使用説明書/サービス説明書
ページ先へ移動 of 37
DMP-1 00 Installation Guidelines R59770263/06 15/09/2011.
Barco n v Media & Entertainment D ivision Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ont ent s T ABLE OF C ONTEN TS 1 . S a f e t y ...... ...... .... .... ...... .... .... ...... .... .... ...... .... .... ...... .... .... ...... .... .... ...... .... .... ...... .. 3 1.1 Important Safety Instructions ....................
Tabl e of co nt ent s 2 R59770263 DMP-100 15/09/2011.
1. Safety 1. SAFETY 1.1 Important Safety Instructions Instructio ns: • Read these instructions. • Keep the se instructions. • Heed all warnings. • Follow all instructions. • Do NO T subm erge fully or partly in water or other liquids. • Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking.
1. Safety • Maximum am bient temperature: The maximum recommended ambient temperature for t his equipment is 50° C. • Flammable m aterials: Keep fl amm able materials away from the instal lation (such as curtains). A lot of energy is transferred into heat.
2. Introdu ct ion 2. INTROD UCTION Overview • General functionality • Order info DMP-100 processor • Content of a DMP-100 package • T ec hnical summary • Dimen sions of the DMP-100 processor • Com ponents of the DMP-1 00 processor 2.
2. Introduc tion 2.2 Orde r info DMP-100 proces sor Order info: Article number Description R9828833 DMP-100 processor 2.3 Content of a DMP- 100 package Packa ge 1 2 3 4 Image 2-3 1 Protecti ve cover for the DMP-100 processo r and installati on manual.
2. Introdu ct ion 2.4 T echnical summary Summary Ty p e V a l u e Input DVI input (supported resolutions 800x600 / 1024x768 / 1600x1200) Compatibility Barco DVI based LED walls, S 10XP FX or newer (Barco NNI tiles are not supported) Output DVI-A, Barco LED protocol.
2. Introduc tion 2.5 Dimens ions of the DMP-100 processor Dimensions of the DMP-100 processor 1 10 mm 250 mm 266 mm 1 10 mm 250 mm 262.4 mm 56 mm 1.5 mm Image 2-4 2.
2. Introdu ct ion 4 Cooling fan s. 5 Soft support s. 6E T L c e r t i fi cat ion label. R59770263 DMP-100 15/09/2011 9.
2. Introduc tion 10 R59770263 DMP-100 15/09/2011.
3. P hysica l instal latio n of the DM P-100 pr ocess or 3. PHYSICAL INST ALLA TION OF THE DMP-100 PROCESSOR Overview • Installation requirements • Connections of the DMP-100 processor 3.
3. Ph ysica l install ation of the DMP- 100 proces sor 3.2 Connections of the DMP-10 0 processor Front panel connections 1 2 3 4 5 6 7 8 9 10 11 Image 3-2 Nr .
3. P hysica l instal latio n of the DM P-100 pr ocess or W ARNING : The power connection is located on the back side of the DMP -100 processor and includes an inte gr ate d int err up tio n sw itc h.
3. Ph ysica l install ation of the DMP- 100 proces sor 14 R59770263 DMP-100 15/09/2011.
4. Cables f or the DMP-100 pr ocess or 4. CABLES FOR THE DMP-100 PROCESSOR 4.1 Ca bles List with a vailabl e cables Article number Description Image Z3499213 Used to connect a LE D-W ALL and a Barco display . (T-16/TF-16/SP- 20/S14/T20/TF-20/SLITE/S10XP) Image 4–1 R326103 Power cable with CEE7 plug.
4. Cables for th e DMP -100 process or 16 R59770263 DMP-100 15/09/2011.
5. Embed ded PC 5. EMBEDDED PC Overview •C o n fi guration • Embedded PC operating system, settings •S p e c i fi cations of the em bedded PC 5.1 Con fi gura tion Con fi guration of the embedded PC The embedded PC is a powerful built-in PC which is used as control PC.
5. Embedded PC W ARNING : The Play PC is always used as default. If the Play PC does not exist or h as been damaged, the DMP-100 processor w ill automatically use the embedded P C as a back up solution. If the play PC has b een damaged , a noti fi cation will b e given by the used control software.
5. Embed ded PC Or , cli ck Start → Control panel .F r o m t h e Classic View of that panel, double click on Date and Time . Image 5-3 2. Click on Time Zon e tab. 3. Click on the drop down list to select the time zone that corresponds to the time zone where the DMP-100 is being installed.
5. Embedded PC Image 5-4 3. Click on the H ardware ta b (2 ). 4. Make sure the disk drive corr esponding to the C: drive is selec ted in the All disk drives section (3 ). 5. Click Properties (4). 6. Click on the Po licies tab (6). 7. Uncheck the Enab le write caching on the disk box (7).
5. Embed ded PC Enhanced IDE interface ICH7M support Single, independent IDE signal channel Supports one CF device Serial ports T wo serial RS-232 ports, COM1(RS -232), DB-9 COM2(RS-232/422/485) Paral.
5. Embedded PC 22 R59770263 DMP-100 15/09/2011.
6. Confi gura tion s cheme 6. CONFIGURA TION SCHEME 6.1 Overvie w Sche me DVI input Formated V ideo Data SOURCE 1 Optional Control PC DMP-100 Display SOURCE 2 Remote control through TCP/IP ** ** Image 6-1 *T h e fi berlink is optiona l. ** Default co nnection.
6. Configur atio n sch eme Image 6-3 3. Turn on the power of the DMP-100. Note: The Led’ s indicated with “PWR” and “MCU” will li ght up. 4. Use the REAL VNC application on the rem ote PC to login to the embedded P C. 5. U se the RMS control software to communicate with the DM P-100 processor .
6. Confi gura tion s cheme If a d ispl ay or bi ll board i s up and running, th e user c an start from ste p 3. Connect the control PC with the DMP-100 processor , using a USB li ne on the USB-UART port, to update t he software and fi rmware used by the DMP -100 processor through the embedded Flash Load er software.
6. Configur atio n sch eme Alternatively , s tep 2 and 3 can be carri ed out together by pushing the reset button. Use the Flash Loader softwa re to downlo ad updates on the softw are and fi rmw are used by the DMP-100 pro - cessor .
7. Contr ol so ftw are 7. CONTROL SOFTW ARE 7.1 RMS General introduc tion RMS control software is running on the embedded PC inside DM P-100 to con fi gure and control the DMP-10 0 and as sociated LED wall from basic set-up to advanced features such as input timing, bright ness control setup and monitoring tools.
7. Contr ol softwar e Image 7-2 3. Click Commu nication > RS232 Con fi g > Baud , and select 38400 . 4. Click Communicati on > RS232 Con fi g > COM Port , and select the COM port on the PC to whic h the DMP-100 is connected.
8. Mainte nance 8. MAINTENANCE 8.1 Cleaning the cabinet C AUTION : Do not use liquid cleaners or aerosol cleaners. Never use strong solvents, s uch as thinner or benzine, or abrasive cleaners, since these w ill damage the cabinet. Necessary t ools Damp cloth.
8. Maintenan ce 30 R59770263 DMP-100 15/09/2011.
9. E nviron mental inf ormation 9. ENVIRONMENT AL INFORMA TION 9.1 Disposal informa tion Disposal Information This equipment has required the extract ion and use of natural res ources for its producti on. It may c ontain hazardous substances for health and environment.
9. Envir onmenta l info rmation 32 R59770263 DMP-100 15/09/2011.
Revision S heet To : Barco nv Media & Entertainment Division/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.1 1, F ax: +32 56.36.88.24 Support: www .
デバイスBarco R59770263/06の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Barco R59770263/06をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBarco R59770263/06の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Barco R59770263/06の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Barco R59770263/06で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Barco R59770263/06を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBarco R59770263/06の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Barco R59770263/06に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBarco R59770263/06デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
