Sun Microsystemsメーカー150の使用説明書/サービス説明書
ページ先へ移動 of 20
Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U .S.A. 650-960-1300 Send comments about this document to: docfeedback@sun.com Sun Blade™ 150 CD-R OM, D VD-R OM, and Hard Dr iv e Installation Guide P ar t No.
Please Recycle Copyright 2002 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc. has intellectual pr operty rights relating to technology embodied in the product that is described in this document.
iii Contents Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation 1 Required Tools 1 Preparing to Replace Components 2 Powering Off the System 2 Removing the System Cover 3 Attaching the Antista.
iv Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 Cleaning a CD or DVD 16 Handling and Storing CDs and DVDs 16.
1 Sun Blade 150 CD-ROM, DVD-ROM, and Har d Drive Installation This guide provides instructions for installing a CD-ROM, DVD-ROM, or hard drive in your Sun Blade 150™ system. Requir ed T ools The following tools are r equired to service the Sun Blade 150 system: ■ No.
2 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 Pr eparing to Replace Components Follow these procedur es to ensure that you safely save data and power off the system. Powering Of f the System Caution – Exit from the operating system before turning of f system power .
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 3 2. V erify the following: ■ The front panel power -indicator LED is off. ■ The system fans are not spinning. 3. T urn off the power to the monitor and any peripheral equipment. 4. Disconnect cables to any peripheral equipment.
4 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 FIGURE 2 Removing the System Cover Attaching the Antistatic W rist Strap 1. Unwrap the f irst two folds of the wrist strap. W rap the adhesive side f irmly against your wrist.
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 5 FIGURE 3 Attaching the W rist Strap to the Chassis Removing a Primary Har d Drive 1. Power off the system, remove the system cover , and attach an antistatic wrist strap as described in “Preparing to Replace Components” on page 2.
6 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 8. Lift the hard drive tray from the hard drive. FIGURE 4 Removing and Replacing a Primary Hard Drive 1 2 3 4 CD/D VD-R.
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 7 Replacing a Primary Har d Drive Note – Read the hard drive pr oduct guide for information about jumpers, switch settings, or other installation tasks.
8 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 Installing a Secondary Har d Drive The optional secondary hard drive mounts next to the primary hard drive on the hard drive tray ( FIGURE 5 ). The secondary IDE cable assembly is used with the secondary hard drive.
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 9 FIGURE 5 Installing a Secondary Hard Drive 10. V erify that the secondary IDE cable connector is connected to riser board connector IDE2 (J503). See FIGURE 7 . Note – Ensure that the cables ar e properly oriented by aligning the connector keys.
10 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 FIGURE 6 Riser Board, Side T wo 13. Connect the power cable to the secondary hard drive ( FIGURE 7 ). 14. Connect the power cable to the primary hard drive. 15. Connect the secondary hard drive to the cable connector labeled “Secondary HDD”.
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 11 16. Detach the wrist strap, replace the system cover , and power on the system as described in “Finishing Component Replacement” on page 13. Removing a CD-ROM or DVD-ROM Drive 1. Remove any CD or DVD media from the drive.
12 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 FIGURE 8 Removing and Replacing a CD-ROM or DVD-ROM Drive Replacing a CD-ROM or DVD-ROM Drive Note – Before you r ep.
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 13 6. Detach the wrist strap, replace the system cover , and power on the system as described in “Finishing Component Replacement” on page 13. Finishing Component Replacement 1. Remove the wrist strap from the system chassis and from your wrist.
14 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 Powering On the System 1. Connect the system power cord to the system and to an AC power outlet. 2. Reconnect and turn on power to any peripherals (so that the system can recognize the peripherals when it is powered on).
Sun Blade 150 CD-ROM, D VD-ROM, and Hard Drive Installation 15 Har d Drive Mirroring Conf iguration The IDE subsystem of the Sun Blade 150 system has two independent channels designated “primary” and “secondary .” The system riser board has a connector for each IDE Channel, labelled IDE1 (J504) and IDE 2 (J503).
16 Sun Blade 150 CD-ROM, DVD-ROM, and Hard Drive Installation Guide • June 2002 2. Place the CD (label side up) into the tray . Ensure that the CD is pr operly set into the recessed area of the tray . 3. Push the tray to close it. Ejecting a CD or DVD Y ou may need to unmount the CD before manually ejecting it.
デバイスSun Microsystems 150の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sun Microsystems 150をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSun Microsystems 150の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sun Microsystems 150の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sun Microsystems 150で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sun Microsystems 150を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSun Microsystems 150の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sun Microsystems 150に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSun Microsystems 150デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
