SunbeamメーカーHE3100の使用説明書/サービス説明書
ページ先へ移動 of 16
Convection Plus Heaters Instruction Booklet HE3100 1200W heater with micathermic elements HE3900 2200W heater with micathermic elements Please read these instructions carefully and retain for future reference.
C o n t e n t s I m p o r t a n t i n s t r u c t i o n s – r e t a i n f o r f u t u r e u s e . Sunbeam’s Safety Precautions 1 Sunbeam’s T otal Safety System 3 Features of your HE3100 Convecti.
1 If you have any concerns regarding the performance and use of your appliance, please visit www .sunbeam.com.au or contact the Sunbeam Consumer Service Line.
2 If you have any concerns regarding the performance and use of your appliance, please visit www .sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. S u n b e a m ’ s S a f e t y P r e c a u t i o n s • Th is he ate r bec ome s hot d uri ng us e.
3 Safety auto shut-off Y our Sunbeam Convection Plus Heater is equipped with a safety system that detects any abnormally high temperatures within the heater and automatically cuts power to the heating element, preventing overheating. Once the heater has cooled it will automatically resume normal operation.
Double heat micathermic elements The revolutionary micathermic heating elements produce both radiant and convection heat. Instant heat radiates from the large surface area in one minute, while natural convection circulates warm air around the room quickly and evenly .
5 Power ON light Illuminates to indicate that the heater is switched on. Mode dial T urn the mode dial to select your desired setting: OFF , LOW (1) or HIGH (2). Thermostat indicator light The red thermostat light indicates that the heater is warming up to the selected temperature and will go out when the selected temperature has been reached.
HI C 6 F e a t u r e s o f y o u r H E 3 9 0 0 C o n v e c t i o n P l u s H e a t e r Double heat micathermic elements The revolutionary micathermic heating elements produce both radiant and convection heat.
HI C 7 Remote control The easy to use remote control enables the heater to be operated from anywhere in the room. LED screen The LED screen displays the current settings including the ambient room temperature, the selected mode, or timer setting. ON/OFF switch Illuminates to indicate that the heater is switched on.
1. Place the heater on a flat level surface and ensure that the air intake and outlet are clear of obstructions. Note: When turned on for the first time, your new heater will emit a slight odour for up to 8 hours. This is due to the initial heating of the materials used.
9 1. Place the heater on a flat level surface and ensure that the air intake and outlet are clear of obstructions. (Refer to Note on Page 8). 2. Ensure that the ON/OFF switch is in the OFF position. 3. Insert the plug into a 230/240V power outlet and turn the power on.
10 3. Use the plus/minus arrows to select your desired setting. The LED screen will flash the set value for 5 seconds. After 5 seconds the LED screen will display the ambient room temperature. Note: The temperature range is from 15ºC to 28ºC. If you scroll past 28ºC the display will automatically return to 15ºC.
11 Wall mounting 1. Before wall mounting your heater , remove the wheels. 2. Mark the screw location on the wall, approximately 1 metre from the floor . Note: The heater must be fixed no lower than 6.5cm above the floor and no higher than 1.8 metres above the floor .
12 Ensure that the heater is switched off and disconnected from the power outlet before cleaning. Carefully wipe the exterior of the heater with a soft damp cloth and dry thoroughly with a dry cloth. Over time, dust may accumulate on the front grille.
‘S unbe am’ , is a re gis te red tr ade mark o f Su nbea m Co rpor ati on . Ma de in Ch ina . Du e to min or ch an ges in d esig n or ot herw ise , th e prod uct may di ffe r from t he on e sho wn in th is le af let. B ac ked by S unbe am’ s 3 Y ear Re pla ceme nt Gu aran tee and Na tio na l Serv ice Ne two rk .
Consumer Hotline Australia 1800 025 059 New Zealand 0800 786 232 www .sunbeam.com.au is a registered T rademark of Sunbeam Corporation Limited. ABN 45 000 006 771.
デバイスSunbeam HE3100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sunbeam HE3100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSunbeam HE3100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sunbeam HE3100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sunbeam HE3100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sunbeam HE3100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSunbeam HE3100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sunbeam HE3100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSunbeam HE3100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。