SunfireメーカーSRS210W-Gの使用説明書/サービス説明書
ページ先へ移動 of 20
Installation Instructions SRS–210W -C Cabine t SRS–210W -B Baffle SRS–210W -G Grille.
User's Manual W ARNING: THIS SUBWOOFER SYSTEM IS CAP ABLE OF PRODUCING VERY HIGH SOUND PRESSURE LEVELS. YOU MUST T AKE EVERY PRECAUTION TO PROTECT YOUR HEARING FROM PERMANENT DAMAGE. Important Safety Instructions 1. Read Instructions 2. Keep these Instructions 3.
User's Manual For more information on this and other Sunre products, please visit our website: www .sunre.com Safety Instructions ............ 2 Introduction ...................... 4 Unpacking ........................ 5 Dimensions .........
User's Manual Introduction Thank you for purchasing this Sunre SubRosa™ Subwoofer . We hope you enjoy it and the music it makes as much as we have enjoyed creating it for you.
User's Manual Installation overview The cabinet may be mounted vertically between wall studs. The width is ideal for tting between vertical 2x4 studs, spaced 16 inches apart.
User's Manual Dimensions 0 1.261 in/ 32.1 mm 13.045 in/ 331.343 mm 14.250 in/ 362 mm 3.533 in/ 89.7 mm 10.717 in/ 272.2 mm 0 35.590 in/ 904 mm 44.500 in/ 1,130.3 mm 3.500 in 88.9 mm Front View Back View Side View 8.830 in/ 224.3 mm Front Cutout required in wall to fit woofer assembly 11.
User's Manual The suggestions below will typi- cally result in outstanding performance. However , although low frequencies are non-directional, factors such as room reections, standing waves, resonance and absorption will strongly affect your subwoofer ’s performance.
User's Manual Center location Installing the subwoofer closer to the center of the front wall will still provide adequate bass, but will tend to be less “heavy” and somewhat tighter . This is ideally suited for: • For rooms smaller than 200 square feet • Dedicated music listening rooms.
User's Manual Framing V ertical mounting Due to residential construction meth- ods, vertical mounting of the cabinet is recommended. The subwoofer cabinet will t between 2 x 4 inch studs on 16 inch centers. Horizontal mounting is also possible, but needs additional framing steps.
User's Manual Cabinet Installation 1. With the help of an assistant to lift the cabinet, check the t of the cabinet into the framing. Use wood shims if there is any gap between the cabinet sides and the vertical studs. 2. If it makes it easier , you can con - nect the wiring to the cabinet before you secure it in place.
User's Manual Wiring 1. Install the speaker wires following all local codes for electrical wiring installation. Use class 2 wiring, and 12 gauge is recommended, 16 gauge is the minimum. 2. Follow common low voltage practices like avoiding high voltage electrical wiring, or crossing them perpendicularly .
User's Manual Final Rough-in 1. Make sure the debris shield is tted into the cabinet opening using the plastic push rivets supplied. This will prevent dust and sheetrock debris from entering the cabinet.
User's Manual Sheetrock installation 1. Apply glue to the framing surround- ing the cabinet. Also apply glue to the front surface of the cabinet, wherever it will be in contact with the sheetrock. 3. Fit the sheetrock in place with sheetrock screws spaced 4 inches apart.
User's Manual Horizontal mounting In this position, the subwoofer's longest side is horizontal. This may be required for some installations, although it requires more framing work. The procedure for mounting is basically the same as the vertical mounting.
User's Manual 3. With the help of an assistant to lift the cabinet, check the t into the framing, and use shims if required. 4. Wiring the subwoofer is the same as described previously , except that there is not much room to make the connections to the binding posts.
User's Manual W oofer bafe installation With the cabinet installed, and all the sheetrock, nishing and decorating done, the woofer bafe can be installed.
User's Manual Bafe installation procedure 1. Remove the debris shield from the front of the in-wall cabinet. Y ou can do this by cutting the cardboard with a sharp knife and pulling out the cardboard pieces and the plas- tic rivets holding it in place.
User's Manual Grille installation With the woofer bafe installed, and the subwoofer tested, the grille can now be installed. The grille assembly consists of the fol- lowing components: • The grille frame. This screws to the woofer bafe and holds the grille in place.
User's Manual Installing the grille assembly 1. Secure the grille frame to the woofer bafe using 12 screws supplied in the grille package. 2. If you have already painted the frame and grille, please jump to step 6. 3. Fit the supplied cardboard paint shield into the frame to cover the woofers and bafe.
Manual 913-142-00 Rev 7 SRS–210W -C Cabinet SRS–210W -B Baffle SRS–210W -G Grille.
デバイスSunfire SRS210W-Gの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sunfire SRS210W-Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSunfire SRS210W-Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sunfire SRS210W-Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sunfire SRS210W-Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sunfire SRS210W-Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSunfire SRS210W-Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sunfire SRS210W-Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSunfire SRS210W-Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。