Sunwave Tech.メーカーSRC-7000の使用説明書/サービス説明書
ページ先へ移動 of 75
SRC-7000 Touch Screen Smart Remote Control User’s Manual 041201.
Preface i Preface About this manual This manual is designed to make using the SRC-7000 Smart Remo te Control as easy as possible. Information in thi s document has b een carefully chec ked for accuracy and is s ubject to chan ge without notice. Copyright © Copyright 2005 This document is protec ted by the internati onal copyright law.
1 Table of Contents Preface ................................................................................... i T able of Contents ................................................................. 1 Chapter 1 Introduction to the SRC-7000 ...........
2 Chapter 3 How to Set Up Y our SRC-7000 ........................ 21 3.1 Add a Device ............................................................... 21 3.1.1 Create a New Device ........................................................................
3 Chapter 4 Menus ............................................................... 52 4.1 Set Up the Remote ..................................................... 52 4.2 Key Layout .................................................................. 56 4.
4 Chapter 1 Introduction to the SRC-7000 Congratulations on purchasing SRC-7000 Smart Remote Control (SRC-7000). The SRC-7000 is a digita l Universal Remote Cont rol with smart design that is easy to configure and use, enabling you to control all your IR equipped electronic devices.
Chapter 1 Introduction to the SRC- 7000 5 1.1 SRC-7000 Features This following list identifies SRC-7000 key features. For more information on getting the most, please refer to the following chapters. 1. Control up to 64 devices including VCD/DVD, TV , Satellite, VCR, CD/MD, Receiver/T uner, T ape, etc.
SRC-7000 User’s Manual 6 1.3 Battery Installation Please refer to the following illustration and instructions for inserting the batteries 1. Rem ove batt ery cover . 2. In sert ba tteries. Ensure that you insert the batte ries acco rdin g to the ma rking insid e the batt ery case.
Chapter 1 Introduction to the SRC- 7000 7 1.3.1 Battery Precautions Please pay attention to the following instructions: 1. Be sure that the positive (+) and negative (-) polarities of each battery match the polarities indicated in the compartment. 2. Do not expose the batteries to excessive heat or flame.
SRC-7000 User’s Manual 8 1.5 Identifying Components Please refer to the following illustrations to identify the components of SRC-7000. This section provides you an overview of the SRC- 7000. For the detailed description on operation, please refer to Chapter 3.
Chapter 1 Introduction to the SRC- 7000 9 1.5.2 Botton of SRC-7000 Figure 1-4: Rear view 1. IR port This needs to be pointed to the IR receiver of the targeted device. 2. Reset switch You can reset the SRC-7000 when the SRC-7000 does not work properly or hangs up (freezes).
SRC-7000 User’s Manual 10 1.5.3 Direct Access Bu ttons ( Rubber Keys) The Direct Access Buttons provi de you with easy access to often- used functions such as volume, channel contro l, skip to the next, skip to the previous, reverse, play and stop… etc.
Chapter 1 Introduction to the SRC- 7000 11 1.5.4 LCD Touch Screen The LCD (Liquid Crystal Display) touch screen enables you to configure and operate your SRC-7000 with the touch of a finger . 1.5.5 Precautions When Using the Touch Screen Please pay attention to the following instructions to avoid damaging your SRC-7000.
SRC-7000 User’s Manual 12 1.5.6 Touch Screen Keys The touch screen keys enable you to control your devices as you would do with your original remote control. Y ou can also set up macros, program timers, cycle ke ys and configure the LCD screens as you want.
Chapter 1 Introduction to the SRC- 7000 13 Introducing the frequently used LCD Layout as followed: y Device Layout T ap the device key directly to enter the device page. n TV Device name / present status (P .21 ) o Soft key in the device (P .27) p Cycle key (P .
SRC-7000 User’s Manual 14 y Basic Information Layout After pressing the icon, you can get the basic information as follow: n Date information (P .52) o T ime information (P .
Chapter 1 Introduction to the SRC- 7000 15 y Setup Menu Layout When you are under the setup status you will see the icons as follows: n Help Guid e: T ap this icon to get the setup process information. Y ou can press or to read the information pages. After reading the tips, press button to exit.
SRC-7000 User’s Manual 16 Timer Macro Se tup Mode o T ap the icon directly to change the functions in T imer Macro. Add / Edit the Timer Macro (P .45) Re-label the T imer Macro (P .
17 Chapter 2 Quick Start This chapter shows you how to quickly set up the SRC-7000, for a more detailed set up please refer to Chapter 3. At turn on, the SRC-7000 will show the welcome greeting message on the screen. From now on, you formally enter the setup procedure.
SRC-7000 User’s Manual 18 2.2 Date / Time Setting 1. Press button for 2 seconds for entering Setup Menu. 2. Scroll the or buttons to choose Setting item and press button for entering “Setting” menu. 3. Scroll the or buttons to select Date item and press button for confirmation.
Chapter 2 Quick Start 19 2.3 Device Setting SRC-7000 will automatically get through the setup mode when you operate the SRC-7000 for the first time. 1. Select the targeted device you wish to set up. Please tap the target device key in the Main Menu to enter “Setup device” menu.
SRC-7000 User’s Manual 20 If the codes are not correct please repeat steps and select “ All ”. Repeat the ~ again to find the proper code for your target device.
21 Chapter 3 How to Set Up Your SRC-7000 In this chapter , you can f ind all the topics about how to setup the SRC- 7000. Each topic has its detailed instruction. Y ou can easily customize the SRC-7000 by the procedures. 3.1 Add a Device With this function, you are able to create a new device for the SRC- 7000.
SRC-7000 User’s Manual 22 4. 5. 4. Please choose two points within the desired block on LCD & . A “ v ” symbol will appear where you tapped. After you determine the second point , the key frame will show up on the screen automatically. Tap the frame to confirm the location.
Chapter 3 How to Set Up Your SRC- 7000 23 6. 7. 6. Please decide the “ Device Category ” for your device by pressing the or buttons. Press the to confirm and enter next step. 7. Finally, please decide how you will load the IR remote codes for the device.
SRC-7000 User’s Manual 24 1. 2. 3. 1. Decide the “ Device Category ” for your device by pressing the or buttons. Press the to confirm and enter to next step. 2. Decide how you will load the IR remote codes for the device. Select “ Pre-code ” press to confirm.
Chapter 3 How to Set Up Your SRC- 7000 25 B. Learning With this function, the SRC-7000 is able to learn IR remote cod es directly from your original remote. Y ou can also learn codes if you fail to get the right remote codes in the pre-programmed code database.
SRC-7000 User’s Manual 26 When you have successfully added a new device, and want to learn the codes for the device, choose the “ Learning ” item to program the unit. 1. 2. 1. Decide the “ Device Category ” for your device by pressing the or buttons.
Chapter 3 How to Set Up Your SRC- 7000 27 Learning successfully Learning fail 4. 5. 4. Press the corresponding key on your original remote for about 2-3 seconds until the symbol shows up on the LCD to make sure the SRC-7000 has learnt the code. 5. If the symbol shows up, it means that the SRC-7000 has failed to learn the remote codes.
SRC-7000 User’s Manual 28 1. Please press the button for about 2 seconds to enter Setup Menu. And then enter “ Key Layout ” menu. 2. Select the “ Add Key” item and then enter the submenu. On tapping the soft key, you will see the indication for the function.
Chapter 3 How to Set Up Your SRC- 7000 29 3.3 Adding Text With this function, you are able to add a text for description. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu. And then enter “ Key Layout ” menu. 2. Choose the “ Add Text ” item and then you will enter the submenu.
SRC-7000 User’s Manual 30 6. You will be able to see the new-added text on the LCD layout. 7. If you intend to add another text, please repeat step 3~6. a. The length of text you can add to the des cription will depend on the po ints you choos e. b.
Chapter 3 How to Set Up Your SRC- 7000 31 3. Please select the device you want to rename. 4. 5. 6. 4. Next you will need to make a decision: to re-label the device itself or to go into the device to re-label its soft keys. Re-label device: If you decide to re-label the device, please key in the new name.
SRC-7000 User’s Manual 32 3.5 Re-size a Device, Key or Text With this function, you are able to re-size a device, soft key or text. Y ou can also use the function to change the locations for them. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu.
Chapter 3 How to Set Up Your SRC- 7000 33 6. After you determine the second point, the key frame will show up on the screen automatically. Tap the frame to confirm the location. 7. After finished the edit, press the button to confirm your decision. 8.
SRC-7000 User’s Manual 34 4. 5. 6. 4. Then you will need to make a decision: to delete the device itself or to go into a device to delete the soft keys. Press the button to confirm the selection. 5. If you select a device to delete, you will see a message to co nfirm your decision.
Chapter 3 How to Set Up Your SRC- 7000 35 3.7 Pre-programmed Code SRC-7000 is equipped with a large pre-programmed code database. With this function, you are able to load the code for your device. It also enables you to control your device even if you lose your original remote.
SRC-7000 User’s Manual 36 Tap soft button to start auto searching. When you see the targeted device has been turned off, tap or press any button immediately to stop auto searching. Then press to test the power key. If it can’t work, please go through step as below.
Chapter 3 How to Set Up Your SRC- 7000 37 3.8 Learning With this function, you are able to use the SRC-7000 to learn IR remote codes directly from your original remote. Y ou are able to control your devices with the SRC-7000, even if the code for your device is not included in the database.
SRC-7000 User’s Manual 38 1. 2. 3. 1. Press the button for 2 seconds to enter the Setup Menu, then enter the “ Code Setting ” menu. 2. Select the “ Learning ” item then press the button to enter the submenu. You will need to see the help guide for the learning function.
Chapter 3 How to Set Up Your SRC- 7000 39 Learning successfully Learning fail 6. 7. 6. Press the corresponding key on your original remote for about 2-3 seconds until the symbol shows up on the LCD t o make sure the SRC-7000 has learnt the code. 7. If the symbol shows up, it means that the SRC-7000 has failed to learn the remote codes.
SRC-7000 User’s Manual 40 3.9 Learn a Cycle Key Some devices save a circle of commands in one button. The SRC-7000 is equipped with a special Cycle functi on; with this function you are able to replicate the circle of commands. 1. 2. 3. 1. Press the button for 2 seconds to enter the Setup Menu, and then enter the “ Code Setting ” menu.
Chapter 3 How to Set Up Your SRC- 7000 41 this Cycle key. (You can save up to 6 cycle commands in the Cycle key.) 6. Press the button when you have finished lear ning all the circle of commands. 7. If you intend to setup another “ Cycle key” , please repeat step 4~6.
SRC-7000 User’s Manual 42 4. And then you will need to make a decision: to either delete all of the codes for the device, or to go into the device to delete the codes for the keys. If you select a device to delete, you will see a message to confirm your decision.
Chapter 3 How to Set Up Your SRC- 7000 43 1. 2. 3. 1. Press the button for 2 seconds to enter the Setup Menu, and then enter the “ Code Setting ” menu. 2. Choose the “ Macro ” item and then enter the submenu. On pressing the soft key , you will see instructions on how to use the function.
SRC-7000 User’s Manual 44 An Example of setting a Macro Basic device operation for watch DVD: 1. Turn the TV on. 2. Switch the TV to video mo de. 3. Turn the DVD on. 4. Create a two-seco nd delay . 5. Instruct the DVD to play a disc. The commands for the Macro key .
Chapter 3 How to Set Up Your SRC- 7000 45 3.11.2 Timer Macro A. Create a Timer Macro The “ Timer M acro ” function enables you to set devices to turn on at specified times, or to operate a Macro function automatically at a specific time. The function helps you to record movies, turn on music, act as an alarm clock, or implement Home Automation.
SRC-7000 User’s Manual 46 4. Select any key in devices for the commands to use for the Macro. Y ou can save up to 60 commands in one Macro. 5. Select the operation processes between any devices. 6. Select the commands to use. a. You can press th e icon to set up the delay between two commands from 0 ~30 second s.
Chapter 3 How to Set Up Your SRC- 7000 47 B. Delete Y our T i mer Macro With this function, you are able to delete Timer Macros. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu, and then enter the “ Timer Macro ” menu. 2. Choose the “ Delete ” item and then enter the submenu.
SRC-7000 User’s Manual 48 C. Re-label Y our Timer Macro With this function, you can eas ily re-label your Ti mer Macros. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu, and then enter the “ Timer Macro ” menu. 2. Choose the “ Re-label ” item and then enter the submenu.
Chapter 3 How to Set Up Your SRC- 7000 49 D. View Y our Timer Macro With this function, you are able to view all the Macro commands and the timer in the Timer Macro you selected. 1. 2. 3. 1. Press the button for 2 seconds to enter Setup Menu, and then enter the “ Timer Macro ” menu.
SRC-7000 User’s Manual 50 3.12 Set Up Your Favorite Channels Y ou can use the Macros to save your favorite channels. This enables you to get to your favorite channel s ju st by tapping Macros. There are two main steps you need complete: Add some soft keys as Macros and set these Macros as your favorite channels.
Chapter 3 How to Set Up Your SRC- 7000 51 3.12.2 Set Your Favorite Channels as Macros This is done in the same way as you set a Macro (refer to 3.1 1.1 Macro on page 42). Enter “ Macro ” in “ Code Settin g ”, and then choose one of the soft keys you can just create as your Macro key .
52 Chapter 4 Menus 4.1 Set Up the Remote The steps for entering detailed settings in the setting menu are as follows: 1. Press the button for 2 seconds to enter the Setup Menu. 2. Scroll the cursor or and choose the “ Setting ” item, then press the button for entering the “ Setting ” menu.
Chapter 4 Menus 53 Date Use this function to set the date for your remote. 1. Use or to choose the year, month and date. 2. Use or to change the date values. 3. Press to save your settings or press to exit without saving any changes. Tim e Use this function to set the time for your remote.
SRC-7000 User’s Manual 54 LCD Off Use this function to chan g e the idle time ( when no functions are used) before turning off the Display . 1. Use or to chan g e the idle time before the LCD turns off. 2. Idle time can be set up to 600 seconds. (Disable/10sec ~600sec).
Chapter 4 Menus 55 Motion The Motion Detector will sense an y movement and turn on the Displa y automaticall y . Use this function to chan g e the sensitivity of the Motion detector (Off/Slow/Medium/Fast). 1. Use or to chan g e the sensitivit y of the Motion Detector .
SRC-7000 User’s Manual 56 4.2 Key Layout Add Device Use to add your devices to the SRC-7000. Y ou can use “Pre-code” or “Learnin g ” to load the codes for the device (Please refer to Chapter 3.1 Add a Device on page 21). Add Key Use to add new keys to your devices on the SRC-7000.
Chapter 4 Menus 57 4.3 Code Setting Pre-code Use to load the pre-programmed codes for your devices. (Please refer to 3.7 Pre-programmed Code on pa ge 35). Learning Use this function to learn the IR codes from your remotes. (Please refer to 3.8 Learning on page 37).
SRC-7000 User’s Manual 58 4.4 Timer Macro Add / Edit Use to add or edit your T imer Macros on your SRC-7000. Y ou can set the Timer for the Macro at the same time. There are 32 sets of T imer Macros you can use. (Please refer to 3.1 1.2 A. Create a Timer Macro on page 45).
Chapter 4 Menus 59 4.5 Duplicate Duplicate Y ou can connect two SRC-7000s with the Transmi t Cable ( Appendix B P .71) to duplicate the settin g s on one remote and transfer them to another unit. With this function, you are able to transfer your settings to another SRC-7000 using the T ransmit Cable.
SRC-7000 User’s Manual 60 5 6. 6. If the duplication is completed successfully , a message will show up to tell you the completion. If the duplication is not su ccessful, please repeat from step 1 again. If a message “ Dup licate Fail ” shows up, please check the f ollowing points : a.
Chapter 5 Install USB Cable and Software 61 Chapter 5 Install USB Cable and Software 5.1 Introduce SLC-2080 USB Cable SLC-2080 is a cable that enables the SRC-7000 to connect with a PC. Besides, you can also duplicate the settings in one SRC-7000 and transfer data to another SRC-7000 by this cable.
SRC-7000 User’s Manual 62 2. After the program has finished installing the driver, a window will appear as shown below. Click “Finish” to complete the setup processes.
Chapter 5 Install USB Cable and Software 63 5.2 Install Upgrade Tools The Upgrade Tools enable you to upgrade your firmware and pre- programmed codes through the internet. 1. Locate the program from the CD enclosed with the package or download the program from http://www.
SRC-7000 User’s Manual 64 4. Choose a Start menu folder for your Upgrade Tools shortcuts then click “ Next ”. 5. After finishing all steps above, click “ Install ” to start installing the program.
Chapter 5 Install USB Cable and Software 65 6. You have now successfu lly installed Upgrade Tools. Click “ Finis h” to exit the installation..
SRC-7000 User’s Manual 66 5.3 Upgrade VMCU Firmware and VMCF Pre- programmed Codes With the SLC-2080 and the Upgrade Tools, you can easily upgrade your SRC-7000 via Internet. There are two types of files you can upgrade: VMCU Firmware and VMCF Pre-programmed Co des.
Chapter 5 Install USB Cable and Software 67 3. Select “ Data Source ” you will load the files from : * From Internet This option will download the latest database files from Internet. The PC needs to be connected with Internet. Please refer to step 4 for following procedure.
SRC-7000 User’s Manual 68 5. There are two choices in “ Upgrade type ”, “All (Reset to factory default)” and “Pre-programmed code” If you select “ All (Reset to factory default) ”, you will upgrade your pre-programmed code database and erase all your settings on the SRC-7000 simultaneously.
69 Appendix A Features 64 Devices in One: 64 in 1 remote control, no more runnin g out of device buttons. Customization: Users can customize the size, text or icon for buttons. Pre-Programmed Code: Users can access the specific codes for their devices from pre-programmed codes.
SRC-7000 User’s Manual 70 Specifications Model SRC-7000 Battery 3 x AAA 1.5V Alkaline batteries or Ni-MH rechargeable batteries (not inclu ded) Dimensions (WxHxD) 2.
71 Appendix B Optional Accessories SLC-2080 USB Cable T ransmit Cable The SLC-2080 is an optional USB cable that enables transmissio n of system setup between a PC and the SRC-7000. Wi th the Transmit Cable, the SRC-7000 also can duplic ate the user s etup data fro m one unit to another .
72 Appendix C Troubleshooting Tables Problem Solution LCD does not show anything when you touch it. • Batteries may be dead. • Replace the batteries with th ree new AAA Alkaline batteries. • Check the batteries are properly insert with the + - indications.
73 Problem Solution You see an “ error ” display during operation. • The key that you pressed has not been taught or input the IR code. • Teach the key via lear ning procedure. (P.37) IR Learning is not successful. • Do not use the learn function near an incandescent lamp.
デバイスSunwave Tech. SRC-7000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sunwave Tech. SRC-7000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSunwave Tech. SRC-7000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sunwave Tech. SRC-7000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sunwave Tech. SRC-7000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sunwave Tech. SRC-7000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSunwave Tech. SRC-7000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sunwave Tech. SRC-7000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSunwave Tech. SRC-7000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
