SUPER MICRO ComputerメーカーH8DCT-HLN4Fの使用説明書/サービス説明書
ページ先へ移動 of 80
USER’S MANUAL Revision 1.1a ® S UPER H8DCT -HLN4F H8DCT -HIBQF.
The information in this User ’ s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
Preface iii Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the H8DCT -HLN4F/HIBQF serverboard.
iv H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Appendix A provides BIOS Error Beep Code Messages. Appendix B lists BIOS POST Checkpoint Codes..
v T able of Contents Chapter 1 Introduction 1-1 Overview ......................................................................................................... 1-1 Checklist ..........................................................................
vi SXB1 Adapter Card Slot/Connector ......................................................... 2-14 2-9 Jumper Settings ............................................................................................ 2-15 Explanation of Jumpers ...........
T able of Contents vii 3-4 Returning Merchandise for Service................................................................. 3-4 Chapter 4 BIOS 4-1 Introduction .........................................................................................
Notes viii H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL.
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry . Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 1-2 Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
Chapter 1: Introduction 1-3 Figure 1-1. H8DCT -HLN4F Image.
1-4 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Figure 1-1. H8DCT -HIBQF Image.
Chapter 1: Introduction 1-5 Notes: Jumpers not indicated are for test purposes only . Not all ports, jumpers or LED Indicators are available on all serverboards.
1-6 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL H8DCT -HLN4F/HIBQF Quick Reference Jumper Description Default Setting JBT1 CMOS Clear (See Section 2-8) JIB1 In fi niBand Enable/Disable Pins 1-2.
Chapter 1: Introduction 1-7 1-3 Serverboard Features CPU • Dual AMD Opteron 4000 series (AMD Socket C32 type) processors Note: Refer to our web site for details on supported processors.
1-8 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL ACPI Features • Microsoft OnNow • Slow blinking LED for suspend state indicator • BIOS support for USB keyboard Onboard I/O • Four (4) USB (Universal Serial Bus 2.
Chapter 1: Introduction 1-9 AM D Socket C3 2 CPU 2 HT3 Link 16x16 b its 5 .2GT /s PCI-E G EN2 X 16 PCI-E Slot1 PCI-E G EN2 X4 INTE L I350 A-Link SP510 0 SA TA x 6 BM C VG A WPCM450- R PCI SMBus SI O W.
1-10 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 1-4 Chipset Overview The H8DCT -HLN4F/HIBQF serverboard is based on the AMD AMD SR5670 or SR5690 and SP5100 chipset. This chipset functions as a Media and Communications Processor (MCP). Controllers for the system memory are integrated directly into AMD Opteron processors.
Chapter 1: Introduction 1-1 1 CPU Overheat/Fan Fail LED and Control This feature is available when the user enables the CPU overheat/Fan Fail warning function in the BIOS. This allows the user to de fi ne an overheat temperature. When this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail warning LED is triggered.
1-12 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Main Switch Override Mechanism The power button can function as a system suspend button. When the user depresses the power button, the system will enter a SoftOff state. The monitor will be suspended and the hard drive will spin down.
Chapter 1: Introduction 1-13 The Super I/O provides functions that comply with ACPI (Advanced Con fi guration and Power Interface), which includes support of legacy and ACPI power management through a SMI or SCI function pin. It also features auto power management to reduce power consumption.
1-14 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Notes.
Chapter 2: Installation 2-1 Chapter 2 Installation 2-1 Standardized W arning Statements About Standardized W arning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury .
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-2 W arnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr . Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Chapter 2: Installation 2-3 Product Disposal W arning! Ultimate disposal of this product should be handled according to all national laws and regulations.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-4 2-2 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. T o prevent damage to your system board, it is important to handle it very carefully . The following measures are generally suf fi cient to protect your equipment from ESD.
Chapter 2: Installation 2-5 2-3 Processor and Heatsink Installation Caution: Exercise extreme caution when handling and installing the processor. Always connect the power cord last and always remove it before adding, removing or changing any hardware components.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-6 Installing the Heatsinks We recommend the use of active type heatsinks (except for 1U systems). Use any onboard fan header for the CPU's heatsink fan. T o install the heatsink, please follow the installation instructions that are included with your heatsink package.
Chapter 2: Installation 2-7 2-4 Mounting the Serverboard into a Chassis All motherboards have standard mounting holes to fi t different types of chassis. Make sure that the locations of all the mounting holes for both the motherboard and the chassis match.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-8 Note: 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules are supported. It is highly recommended that you remove the power cord from the system before installing or changing memory modules.
Chapter 2: Installation 2-9 Memory Population for Optimal Performance -For a Serverboard with One CPU (CPU1) Installed # DIMMS CPU Channel 1 Channel 2 2 DIMMs CPU1 P1-1A P1-2A 4 DIMMs CPU1 P1-1A P1-1C.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-10 2-6 PCI Expansion Cards A riser card is used to support one standard size (full height full length) PCI expansion card. Installing a PCI Expansion Card 1. Con fi rm that you have the correct riser card for your chassis model and the add-on card includes a standard bracket.
Chapter 2: Installation 2-1 1 2-7 I/O Port and Control Panel Connections The I/O ports are color coded to make setting up your system easier . See Figure 2-2 below for the colors and locations of the various I/O ports. Figure 2-2. I/O Port Locations and De fi nitions 2 1 5 3 4 6 7 Rear I/O Ports 1.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-12 Fan Header Pin De fi nitions Pin# De fi nition 1 Ground 2 +12V 3 T achometer 4 PWR Modulation Fan Header This motherboard has one GPU fan header (GPU_Fan1). This 4-pin fans header is backward compatible with 3-pin fans.
Chapter 2: Installation 2-13 Overheat LED Connect an LED to the JOH1 header to provide warning of chassis overheating. See the table on the right for pin de fi nitions. Overheat LED Pin De fi nitions (JOH1) Pin# De fi nition 1 3.3V 2 OH Active IPMB A System Management Bus header for the IPMI slot is located at JIPMB1.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-14 T rusted Platform Module Header The JTPM1 header is used to connect a T rusted Platform Module (TPM), available separately from a third-party vendor .
Chapter 2: Installation 2-15 2-9 Jumper Settings Explanation of Jumpers T o modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector .
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-16 I2C to PCI-Express Slots JI 2 C1/JI 2 C2 slots allows you to enable the I 2 C bus to communicate with a PCI-Express slot. For the jumpers to work properly , please set both jumpers to the same setting.
Chapter 2: Installation 2-17 Power LED DP2 is an Onboard Power LED. When this LED is lit, it means power is present on the serverboard. Be sure to turn off the system and unplug the power cord(s) before removing or installing components.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-18 In fi niBand LED Indicators T wo I nf ini Ba nd LED i ndi c ator s (LE 2 /L E3) are loc ated n ear t he In fi n i B a n d p o r t o f t h e H 8 D C T - H I B Q F ser verboard. The green LED (LE2 ) is the In fi niBa nd li nk LED w hil e th e yell ow LED (LE3) indi c ates ac ti vit y.
Chapter 2: Installation 2-19 UID LED (LE1) A rear UID LED Indicator, located at LE1, works in conjunction with the rear UID switch to provide easy identi fi cation for a unit that might be in need of service. Refer to Page 2-12 for further UID details.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-20 2-1 1 Enabling SA T A RAID Now that the hardware is set up, you must install the operating system and the SA T A RAID drivers, if you wish to use RAID with your SA T A drives.
Chapter 2: Installation 2-21 Figure 2-4. BIOS Setup Screen Enabling SA T A RAID in the BIOS Before installing the Windows operating system, you must change some settings in the BIOS. Boot up the system and hit the <Delete> key to enter the BIOS Setup Utlility .
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-22 Figure 2-6.Adaptec RAID Utility Program Screen Figure 2-5. DotHill RAID Utility Program Screen.
Chapter 2: Installation 2-23 Using the DotHill and Adaptec RAID Utility The RAID Utility program allows you to de fi ne the drives you want to include in the RAID array and the mode and type of RAID.
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-24 Figure 2-7. Driver/T ool Installation Display Screen 2-12 Installing Drivers The Supermicro Website contains drivers and utilities for your system at ftp://ftp. supermicro.com , some of which must be installed, such as the chipset driver .
Chapter 2: Installation 2-25 Supero Doctor III The SuperDoctor® III program is a Web base management tool that supports remote management capability .
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-26 Note: The SuperDoctor III program and User ’s Manual can be downloaded from the Supermicro web site at http://www .supermicro.com/products/accessories/software/ SuperDoctorIII.cfm .For Linux, we recommend that you use the SuperoDoctor II application instead.
Chapter 2: Installation 2-27 2-13 Serverboard Battery Caution : There is a danger of explosion if the onboard battery is installed upside down, which will reverse its polarites (see Figure 2-10). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer (CR2032).
H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 2-28 Notes.
3-1 Chapter 3: T roubleshooting Chapter 3 T roubleshooting 3-1 T roubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘T echnical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter .
3-2 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL No Video 1. If the power is on but you have no video, remove all the add-on cards and cables. 2. Use the speaker to determine if any beep codes exist. Refer to Appendix A for details on beep codes.
3-3 Chapter 3: T roubleshooting 2. BIOS upgrades can be downloaded from our web site. Note: Not all BIOS can be fl ashed depending on the modi fi cations to the boot block code.
3-4 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Question: Why can't I turn off the power using the momentary power on/off switch? Answer: The instant power of f function is controlled in BIOS by the Power Button Mode setting.
Chapter 4: BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the AMIBIOS™ Setup utility for the H8DCT-HLN4F/HIBQF serverboard. The 16 Mb AMI BIOS® is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
4-2 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 4-2 Main Menu When you fi rst enter AMI BIOS Setup Utility , you will see the Main Menu screen. Y ou can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys.
Chapter 4: BIOS 4-3 W ait for F1 if Error This setting controls the system response when an error is detected during the boot sequence. When enabled, BIOS will stop the boot sequence when an error is detected, at which point you will need to press the F1 button to re-enter the BIOS setup menu.
4-4 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL GART Error Reporting This option should remain disabled for normal operation. The driver developer may enable this option for testing purposes. Options are Enabled or Disabled . Microcode Update This setting Enables or Disables microcode updating.
Chapter 4: BIOS 4-5 Channel Interleaving This option enables channel memory interleaving. Options include Auto or Disabled. CS Sparing This setting will reserve a spare memory rank in each node when enabled. Options are Enabled and Disabled . Bank Swizzle Mode This setting Enables or Disables the bank swizzle mode.
4-6 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL SouthBridge Con fi guration OHCI/EHCI HC Device Functions These settings allow you to either Enable or Disable functions for OHCI or EHCI bus devices. USB 2.0 Controller Mode Use this setting to con fi gure the USB 2.
Chapter 4: BIOS 4-7 Primary/Secondary/Third/Fourth IDE Master/Slave LBA/Large Mode LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are Disabled and Auto . Block (Multi-Sector T ransfer) Block mode boosts IDE drive performance by increasing the amount of data transferred.
4-8 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL S.M.A.R.T . Self-Monitoring Analysis and Reporting T echnology (SMART) can help predict impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk drive support. Select "Disabled" to prevent AMI BIOS from using the S.
Chapter 4: BIOS 4-9 PCIe x16 Slot 1 These settings Enable or Disable the speci fi ed PCIe slot in your system. PCIe x8 Slot 2 These settings Enable or Disable the speci fi ed PCIe slot in your system. Onboard LAN Option ROM Select This setting allows you to select the onboard LAN option ROM for iSCSI or PXE .
4-10 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Remote Access Con fi guration Remote Access Use this option to Enable or Disable Remote Access in your system. If enabled, the settings below will appear . Serial Port Number Use this setting to select the serial port for console redirection.
Chapter 4: BIOS 4-1 1 Hardware Health Con fi guration CPU Overheat Alarm This setting allows you to specify the type of alarm for CPU overheating. Options include The Early Alarm and The Default Alarm . Fan Speed Control Modes This feature allows the user to determine how the system will control the speed of the onboard fans.
4-12 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL The Default Alarm (default setting) is enabled when the T ctl value = 70, and is disabled when the T ctl value drops from 70 to 67.
Chapter 4: BIOS 4-13 ACPI V ersion Features Use this setting the determine which ACPI version to use. Options are ACPI v1.0, ACPI v2.0 and ACPI v3.0. NUMA Support This setting allows you to enable or disable the building of an ACPI SRA T table. WHEA Support This setting allows you to enable or disable Windows Hardware Error Architecture.
4-14 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL IP Address This submenu sets the IP address source as either Static or DHCP . Selecting Static allows you to manually set the IP Address, Subnet Mask and Gateway Address. In the fi eld provided here enter the IP address in the decimal form of xxx.
Chapter 4: BIOS 4-15 4-3 Security Menu AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set fi rst. Change Supervisor Password Select this option and press <Enter> to access the sub menu, and then type in the password.
4-16 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL 4-4 Boot Menu The Boot Menu is accessible only when the "Load Onboard LAN Option ROM" setting (in the PCI/PnP Con fi guration menu) is enabled. Boot Device Priority This feature allows you to prioritize the boot sequence from the list of available devices.
Chapter 4: BIOS 4-17 Retry Boot Devices This option allows you to retry boot devices. Options include Enabled and Disabled . 4-5 Exit Menu Select the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen.
4-18 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Notes.
Appendix A BIOS Error Beep Codes During the POST (Power-On Self-T est) routines, which are performed each time the system is powered on, errors may occur . Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
A-2 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Notes.
B-1 Appendix B: BIOS POST Checkpoint Codes Appendix B BIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self T est, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h.
B-2 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL B-2 Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in order of execution: Checkpoint Code Description E0h The onboard fl oppy controller if available is initialized. Next, beginning the base 512 KB memory test.
B-3 Appendix B: BIOS POST Checkpoint Codes B-3 Uncompressed Initialization Codes The following runtime checkpoint codes are listed in order of execution. These codes are uncompressed in F0000h shadow RAM. Checkpoint Code Description 03h The NMI is disabled.
B-4 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Checkpoint Code Description 2Ah Bus initialization system, static, output devices will be done next, if present. See the last page for additional information. 2Eh Completed post-video ROM test processing.
B-5 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description 52h The memory above 1 MB has been tested and initialized. Saving the memory size information next. 53h The memory size information and the CPU registers are saved. Entering real mode next.
B-6 H8DCT -HLN4F/HIBQF SERVERBOARD USER'S MANUAL Checkpoint Code Description 97h Initialization before the C800 adaptor ROM gains control has completed. The adaptor ROM check is next. 98h The adaptor ROM had control and has now returned control to BIOS POST .
デバイスSUPER MICRO Computer H8DCT-HLN4Fの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
SUPER MICRO Computer H8DCT-HLN4Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSUPER MICRO Computer H8DCT-HLN4Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SUPER MICRO Computer H8DCT-HLN4Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SUPER MICRO Computer H8DCT-HLN4Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SUPER MICRO Computer H8DCT-HLN4Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSUPER MICRO Computer H8DCT-HLN4Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SUPER MICRO Computer H8DCT-HLN4Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSUPER MICRO Computer H8DCT-HLN4Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
