SupermicroメーカーAOC-PG-I2+の使用説明書/サービス説明書
ページ先へ移動 of 40
AOC-PG-i2+ Add-on Card User ’ s Guide Revison 1.0a.
AOC-PG-i2+ Add-on Card User ’s Guide ii The information in th is User’s Manual has been carefully reviewed and is bel ieved to be accurate. The vendor assumes no responsibility for any inaccuracie.
iii Table of Contents Chapter 1 Safety Guidelines ............ ........... .............. ........... .......... 1-1 1-1 ESD Safety Guidelines ............... .............. ........... .............. ........... .... 1-1 1-2 General Safe ty Guidelines .
AOC-PG-i2+ Add-on Card User ’s Guide iv Command Line Uninstall Example ......... .................... .............. ........... . 3-9 Command Line Reinstall/Repair ............ ........... .............. ........... .......... 3-9 Chapter 4 Linux Base Driver for the PRO/1000 Family of Adapters .
v Introduction About this Manual This manual is written for system integr ators, PC technicians and kn owledgeable PC users who intend to integrate SuperMicro's AOC-PG-i2+ add-on card add-on card to their system.
AOC-PG-i2+ Add-on Card User ’s Guide vi Operating Systems Supported The AOC-PG-i2+ add-on card supports the following Operating Systems (OS): • Windows 2000/Windows XP/Windows 2003/Windows 2008/Wi.
vii Cont acting SuperMicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (T echnical Supp ort) Web Site: www .
AOC-PG-i2+ Add-on Card User ’s Guide viii Notes.
1-1 Chapter 1 Safety Guidelines T o avoid personal injury and property damage, carefully follow all t he safety step s listed below when accessing your system or handling the components. 1-1 ESD Safety Guidelines Electric St atic Discharge (ESD) can dama ge electronic components.
AOC-PG-i2+ Add-on Card User ’s Manual 1-2 Notes.
2-1 Chapter 2 Card Components 2-1 Front Components Figure 2-1 shows the front components of the AOC-PG-i2+ add-on card. T able 2-1 lists the add-on card’s front components and their description. Figure 2-1. AOC-PG-i2+ Ad d-on Card Front Connectors and Jumpers T able 2-1.
AOC-PG-i2+ Add-on Card User ’s Manual 2-2 2-2 Front Connectors, Jumpers and LEDs This section describes the front c onnectors, jumpers and LEDs found on the AOC-PG-i2+ add-on card. LAN Port s LAN ports allow the add-on card to connect to a maximum of two network cables.
2-3 Chapter 2: Card Components 2-3 Riser Card The AOC-PG-i2+ add-on card requires a RSC- R1UU-E8PR riser card for connectio n to supported systems ( Figure 2-2 ).
AOC-PG-i2+ Add-on Card User ’s Manual 2-4 2-4 System Inst allation The AOC-PG-i2+ add-on card and R SC-R1UU-E8PR riser card are installed in a PCI-E slot on the mainboard of the system. Simply connect the AOC-PG-i2+ add-on card to the RSC-R1UU-E8PR riser card and install the riser card into the PCI-E slot on t he mainboard ( Figure 2-3 ).
2-5 Chapter 2: Card Components Figure 2-4. Side View of Add-on Card in System AOC-PG-i2+ Add-on Card LAN Ports.
AOC-PG-i2+ Add-on Card User ’s Manual 2-6.
3-1 Chapter 3 Installing the Drivers 3-1 Inst alling the Driver s in Microsoft W indows These instructions apply to all versions of Microsoft™ Windows™ 2000, Windows XP (including Windows XP x64 a.
AOC-PG-i2+ Add-on Card User ’s Manual 3-2 Inst alling Intel PROSet for Wi ndows Device Manager Intel PROSet for Windows Device Manager is installed from the Product CD with the same process used to install drivers. Y ou can se lect Intel PROSet for Windows Device Manager and Advanced Network Services from the Install Options dialog.
3-3 Chapter 3: Installing the Drivers • If RSS is not enabled for all adapters in a team, RSS will b e disabled for the team. • If an adapter that does not support RSS is added to a team, RSS will be disabled for the team. • If a non-Intel adapter is added to a team, RSS will be disabled for the team.
AOC-PG-i2+ Add-on Card User ’s Manual 3-4 In addition, the following consider ations should be not ed when running SetupBD.exe for the driver installation: • If you uninstall an adapter ’s driver from Windows Device Manager , you must reboot before using SetupBD.
3-5 Chapter 3: Installing the Drivers Using the DxSetup.exe Utility DxSetup.exe is a setup utility used for installing Intel PROSet. It detects the system language, searches for the appropriate transform file in the same folder, and then launches PROSETDX.
AOC-PG-i2+ Add-on Card User ’s Manual 3-6 Command Line Examp les Y ou can modify the paths for different operating systems and CD layouts and apply the following command line examples: Launches a Typical Install Silently: • DxSetup.exe /qn /liew • C:install.
3-7 Chapter 3: Installing the Drivers Command Line Swit ches This section describes how to install Intel PROSet using PROSETDX.msi and msiexec.exe from the command line. For more information on msiexec.exe command line parameters, refer to the msiexec.
AOC-PG-i2+ Add-on Card User ’s Manual 3-8 The following uninstalls all the Intel PROSet components. It can be used when the p ath to PROSETDX.msi is not available but the ProductCode of MSI package is known. <path to msiexec.exe> /x <ProductCode of PROSETDX.
3-9 Chapter 3: Installing the Drivers Installing Intel PROSet Silently on Windows Server 2003 for Itanium®-B ased Systems: C:WINNTSystem32msiexec.exe /i D:AppsPROSETDXWin64PROSETDX.msi /qn /liew C: install.log Installing Components but Deselecting ANS: Set the ANS=0 in the command line, for example: C:WINNTSystem32msiexec.
AOC-PG-i2+ Add-on Card User ’s Manual 3-10 Notes.
4-1 Chapter 4: Linux Base Driver for the PRO/1000 Family of Adapters Chapter 4 Linux Base Driver for the PRO/1000 Family of Adapters 4-1 Overview This chapter describes the Linu x* Base Driver for the Intel ® PRO/1000 Family of Adapters. This driver supports the 2.
AOC-PG-i2+ Add-on Card User ’s Manual 4-2 4-3 Building and Inst allation T o build a binary RPM* package of this driver , run rpmbuild -tb <filename.tar.gz> Replace <filename.tar .gz> with the specific file name of the driver. Building a Binary RPM Package 1.
4-3 Chapter 4: Linux Base Driver for the PRO/1000 Family of Adapters rmmod e1000; modprobe e1000 6. Assign an IP address to the interface by entering the followin g, where <x> is the interface number: ifconfi g eth<x> <IP_address> 7.
AOC-PG-i2+ Add-on Card User ’s Manual 4-4 T able 4-1. Command Line Parameter Settings Parameter Name V alid Rang e/ Settings Default Description AutoNeg 0x01-0x0F , 0x20-0x2F 0x2F This parameter is a bit mask that specifies which speed and duplex set tings the board advertises.
4-5 Chapter 4: Linux Base Driver for the PRO/1000 Family of Adapters RxDescriptors 80-256 for 82542 and 82543-based adapters 80-4096 for all other supported adapters 256 This value specifies the number of recei ve buffer descriptors allocated by the driver .
AOC-PG-i2+ Add-on Card User ’s Manual 4-6 Notes on InterruptThrottleRate Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which it dynamically adjusts the InterruptThrottleRate value based on the tr af fic that it receives.
4-7 Chapter 4: Linux Base Driver for the PRO/1000 Family of Adapters In dynamic conservative mode, the InterruptThrottleRate value is set to 400 0 for traf fic that falls in class “Bulk traffic”. If traf fic fa lls in the “Low latency” or “Lowest latency” class, the InterruptThrottleRate is increased stepwise to 20000.
AOC-PG-i2+ Add-on Card User ’s Manual 4-8 If S peed = 10 or 100, then both S peed and Duplex should be set. Auto-negotiation is disabled, and the AutoNeg parameter is i gnored. Partner SHOULD also b e forced. The AutoNeg parameter is used when more control is required over the auto-negotiation process.
4-9 Chapter 4: Linux Base Driver for the PRO/1000 Family of Adapters 4-5 Additional Configurations Configuring the Driver on Diff erent Distributions Configuring a network driver to load properly when the system is started is distribution dependent. T ypically , the configuration pr ocess involves adding an alias line to /etc/modules.
AOC-PG-i2+ Add-on Card User ’s Manual 4-10 Some Intel gigabit adapters that suppor t Jumbo Frames have a frame size limit of 9238 bytes, with a corresponding MTU size limi t o f 9216 bytes. The adapters with this limitation are based on the Intel® 82571EB, 82572EI, 82573L and 80003ES2LAN controllers.
4-1 1 Chapter 4: Linux Base Driver for the PRO/1000 Family of Adapters Ethtool The driver utilizes the Ethtool interface for driver confi guration and diagnostics, as well as displaying statistical information. Ethtool version 1.6 or later is required for this functionality .
AOC-PG-i2+ Add-on Card User ’s Manual 4-12 Notes.
Disclaimer The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilitie s or syste ms, aircraf t, aircraf t devices, aircraft.
AOC-PG-i2+ Add-on Card User ’s Manual Notes.
デバイスSupermicro AOC-PG-I2+の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Supermicro AOC-PG-I2+をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSupermicro AOC-PG-I2+の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Supermicro AOC-PG-I2+の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Supermicro AOC-PG-I2+で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Supermicro AOC-PG-I2+を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSupermicro AOC-PG-I2+の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Supermicro AOC-PG-I2+に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSupermicro AOC-PG-I2+デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
