SupermicroメーカーX7DVL-3 ServerBoardの使用説明書/サービス説明書
ページ先へ移動 of 91
X7DVL-3 USER’S MANUAL Revision 1.1b X7DVL-i.
The information in this User ’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the X7DVL-3/X7DVL-i motherboard. The X7DVL-3/X7DVL-i supports dual Intel Xeon Quad Core/Dual Core processors (w/771 LGA) with a front side bus speed of 667 MHz/1.
iv Preface About This Manual ...................................................................................................... iii Manual Organization ...............................................................................................
T able of Contents v Power Button .......................................................................................... 2-13 2-5 Connecting Cables ......................................................................................... 2-14 A TX Power Connector .
vi Chapter 3: T roubleshooting 3-1 T roubleshooting Procedures ........................................................................... 3-1 Before Power On ....................................................................................... 3-1 No Power .
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry . Super Micro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 X7DVL-3/X7DVL-i User's Manual Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock A ve. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
Chapter 1: Introduction 1-3 X7DVL-3/X7DVL-i Image Note: The drawings and pictures shown in this manual were based on the latest PCB Revision available at the time of publishing of the manual. The motherboard you’ve received may or may not look exactly the same as the graphics shown in the manual.
1-4 X7DVL-3/X7DVL-i User's Manual X7DVL-3/X7DVL-i Motherboard Layout Notes: 1. Jumpers not indicated are for test purposes only . 2. See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front panel connections. 3. " " indicates the location of Pin 1.
Chapter 1: Introduction 1-5 Jumper Description Default Setting JBT1 CMOS Clear See Chapter 2 JI 2 C1/JI 2 C2 SMB to PCI Slot#1/Slot#2 Speed Pins 2-3 (Disabled) JPG1 VGA Enable Pins 1-2 (Enabled) JP A1.
1-6 X7DVL-3/X7DVL-i User's Manual Motherboard Features CPU • Dual Intel ® 64-bit Xeon LGA 771 Quad Core/Dual Core processors at a front side bus speed of 1333 MHz/1067 MHz/667MHz Memory • Si.
Chapter 1: Introduction 1-7 ACPI Features • Slow blinking LED for suspend state indicator • Main switch override mechanism • ACPI Power Management • Power-on mode for power recovery Onboard I/O • Six SA T A ports (supporting RAID0, 1,10 and 5) • Six SAS ports (supporting RAID0, 1,10 and 5.
1-8 X7DVL-3/X7DVL-i User's Manual Block Diagram of the 5000V Chipset Note: This is a general block diagram. Please see the previous Motherboard Features pages for details on the features of each motherboard.
Chapter 1: Introduction 1-9 1-2 Chipset Overview Built upon the functionality and the capability of the 5000V chipset, the X7DVL-3/ X7DVL-i motherboard provides the performance and feature set require.
1-10 X7DVL-3/X7DVL-i User's Manual 1-3 Special Features Recovery from AC Power Loss BIOS provides a setting for you to determine how the system will respond when AC power is lost and then restored to the system.
Chapter 1: Introduction 1-1 1 System Resource Alert This feature is available when used with Supero Doctor III in the Windows OS environment or used with Supero Doctor II in Linux.
1-12 X7DVL-3/X7DVL-i User's Manual External Modem Ring-On W ake-up events can be triggered by a device such as the external modem ringing when the system is in the Standby or Off state. Note that external modem ring-on can only be used with an A TX 2.
Chapter 1: Introduction 1-13 1 Mb/s. It also provides two high-speed, 16550 compatible serial communication ports (UART s). Both UART s provide legacy speed with baud rate of up to 1 15.2 Kbps as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed modems.
1-14 X7DVL-3/X7DVL-i User's Manual Notes.
Chapter 2: Installation 2-1 Chapter 2 Installation 2-1 Static-Sensitive Devices Electro-Static-Discharge (ESD) can damage electronic com ponents. T o prevent damage to your system board, it is important to handle it very carefully . The following measures are generally suf fi cient to protect your equipment from ESD.
2-2 X7DVL-3/X7DVL-i User's Manual Installation of the LGA771 Processor 1. Press the load lever to release the load plate, which covers the CPU socket, from its locking position.
Chapter 2: Installation 2-3 Socket Key (Socket Notch) South Center Edge North Center Edge Load Lever CPU in the CPU socket Plastic cap is released from the load plate if CPU properly installed. 3. Use your thumb and your index fi nger to hold the CPU at the North Center Edge and the South Center Edge of the CPU.
2-4 X7DVL-3/X7DVL-i User's Manual Installation of the Heatsink CEK Passive Heatsink Screw#1 Screw#2 Screw#1 1. Do not apply any thermal grease to the heatsink or the CPU die; the required amount has already been applied. 2. Place the heatsink on top of the CPU so that the four mounting holes are aligned with those on the retention mechanism.
Chapter 2: Installation 2-5 Mounting the Motherboard in the Chassis All motherboards have standard mounting holes to fi t different types of chas- sis. Make sure that the locations of all the mounting holes for both motherboard and chassis match. Make sure that the metal standoffs click in or are screwed in tightly .
2-6 X7DVL-3/X7DVL-i User's Manual 2-3 Installing DIMMs Note : Check the Super Micro web site for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Also note that the memory is interleaved to improve performance (see step 1).
Chapter 2: Installation 2-7 ® S U P E R X 7 DV L - 3 T o Install: Insert module vertically and press down until it snaps into place. Pay attention to the alignment notch at the bottom. Installing and Removing DIMMs T o Remove: Use your thumbs to gently push the release tabs near both ends of the module to release it from the slot.
2-8 X7DVL-3/X7DVL-i User's Manual ® S U P E R X 7D V L - 3 2-4 Control Panel Connectors/IO Ports The I/O ports are color coded in conformance with the PC 99 speci fi cation. See Figure 2-3 below for the colors and locations of the various I/O ports.
Chapter 2: Installation 2-9 ® S U PE R X 7D V L -3 Front Control Panel JF1 contains header pins for various buttons and indicators that are normally located on a control panel at the front of the chassis. These connectors are de- signed speci fi cally for use with Super Micro server chassis.
2-10 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-1 1 Po we r Button OH/Fan Fail LED 1 NIC1 L ED Re set Butt o n 2 HDD LED Po we r LED Reset PWR Vcc Vcc Vcc Vcc Gr ound Gr ound 19 20 Vcc X Gr ound NMI X Vcc PWR Fail LED NIC2.
2-12 X7DVL-3/X7DVL-i User's Manual Po we r Button OH/Fan Fail LED 1 NIC1 L ED Re set Butt o n 2 HDD LED Po we r LED Reset PWR Vcc Vcc Vcc Vcc Gr ound Gr ound 19 20 Vcc X Gr ound NMI X Vcc PWR Fai.
Chapter 2: Installation 2-13 Po we r Button OH/Fan Fail LED 1 NIC1 L ED Re set Butt o n 2 HDD LED Po we r LED Reset PWR Vcc Vcc Vcc Vcc Gr ound Gr ound 19 20 Vcc X Gr ound NMI X Vcc PWR Fail LED NIC2 LED Power Button The Power Button connection is located on pins 1 and 2 of JF1.
2-14 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-15 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-16 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-17 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-18 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-19 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-20 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-21 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-22 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-23 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-24 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-25 PWR Supply Failure/PWR Fault Detect (JPWF) The system can notify you in the event of a power supply failure. This feature is available when three power supply units are installed in the chassis with one act- ing as a backup.
2-26 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-27 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-28 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-29 A. D31: Status LED Status LED (D31) There is a Status LED Indicator (D31) located on the motherboard. This LED displays different colors to show the status of the system. Refer to the table on the right for system status. See the layout below for the LED location.
2-30 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
Chapter 2: Installation 2-31 LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge Fan1 SATA2 .
2-32 X7DVL-3/X7DVL-i User's Manual LAN1 ® S U P ER X 7 D V L - 3 FP Control Fan3 IDE1 Fan4 SATA3 SATA5 PCI 33 MHz Battery GLAN CTRLR North Bridge COM1 ATX PWR 8-Pin PWR 24-Pin CPU2 South Bridge .
3-1 Chapter 3: T roubleshooting Chapter 3 T roubleshooting 3-1 T roubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘T echnical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter .
3-2 X7DVL-3/X7DVL-i User's Manual Losing the System’ s Setup Con fi guration 1. Make sure that you are using a high quality power supply . A poor quality power supply may cause the system to lose the CMOS setup information. Refer to Section 1-6 for details on recommended power supplies.
3-3 Chapter 3: T roubleshooting 3. If you still cannot resolve the problem, include the following information when contacting Super Micro for technical support: • Motherboard model and PCB revision .
3-4 X7DVL-3/X7DVL-i User's Manual Question: What's on the CD that came with my motherboard? Answer: The supplied compact disc has quite a few drivers and programs that will greatly enhance your system. We recommend that you review the CD and install the applications you need.
Chapter 4: BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the Phoenix BIOS™ Setup utility for the X7DVL-3/X7DVL-i. The Phoenix ROM BIOS is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
4-2 X7DVL-3/X7DVL-i User's Manual 4-2 Running Setup * Default settings are in bold text unless otherwise noted . The BIOS setup options described in this section are selected by choosing the ap- propriate text from the main BIOS Setup screen.
Chapter 4: BIOS 4-3 Main BIOS Setup Menu Main Setup Features System Time T o set the system date and time, key in the correct information in the appropriate fi elds. Then press the <Enter> key to save the data. System Date Using the arrow keys, highlight the month, day and year fi elds, and enter the correct data.
4-4 X7DVL-3/X7DVL-i User's Manual X IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, SA T A Port2 and SA T A Port3 These settings allow the user to set the parameters of IDE Channel 0 Master/ Slave, IDE Channel 1 Master/Slave, IDE Channel 2 Master , IDE Channel 3 Master slots.
Chapter 4: BIOS 4-5 CHS Format The following items will be displayed by the BIOS: TYPE: This item displays the type of IDE or SA T A Device. Cylinders: This item indicates the status of Cylinders. Headers: This item indicates the number of headers. Sectors: This item displays the number of sectors.
4-6 X7DVL-3/X7DVL-i User's Manual Parallel A T A This setting allows the user to enable or disable the function of the Parallel A T A. The options are Disabled and Enabled . Serial A T A This setting allows the user to enable or disable the function of the Serial A T A.
Chapter 4: BIOS 4-7 System Memory This display informs you how much system memory is recognized as being present in the system. Extended Memory This display informs you how much extended memory is recognized as being present in the system. 4-4 Advanced Setup Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow keys.
4-8 X7DVL-3/X7DVL-i User's Manual X Boot Features Access the submenu to make changes to the following settings. QuickBoot Mode If enabled, this feature will speed up the POST (Power On Self T est) routine by skipping certain tests after the computer is turned on.
Chapter 4: BIOS 4-9 X Memory Cache Cache System BIOS Area This setting allows you to designate a reserve area in the system memory to be used as a System BIOS buffer to allow the BIOS to write (cache) data into this reserved memory area. Select Write Protect to enable this function, and this area will be reserved for BIOS ROM access only .
4-10 X7DVL-3/X7DVL-i User's Manual to be cached into the buffer and written into the system memory at the same time. Select Write Protect to prevent data from being written into the extended memory area above 1MB.
Chapter 4: BIOS 4-1 1 X Slot1 PCI 33MHz, Slot5 PCI-X 133MHz, Slot6 PCI-X 133MHz, Slot6 <Ext> PCI-Exp. x8 Access the submenu for each of the settings above to make changes to the following: Option ROM Scan When enabled, this setting will initialize the device expansion ROM.
4-12 X7DVL-3/X7DVL-i User's Manual Branch 0 Rank Interleaving Select enable to enable the functions of Memory Interleaving for Branch 0 Rank. The options for Memory Interleaving are 1:1, 2:1 and 4:1 . Branch 0 Rank Sparing Select enable to enable the sparing feature for Branch 0 Rank.
Chapter 4: BIOS 4-13 Route Port 80h Cycles to This feature allows the user to decide which bus to send debug information to. The options are Disabled, PCI and LPC .
4-14 X7DVL-3/X7DVL-i User's Manual Thermal Management 2 (A vailable when supported by the CPU.) Set to Enabled to use Thermal Management 2 (TM2) which will lower CPU voltage and frequency when the CPU temperature reaches a prede fi ned overheat threshold.
Chapter 4: BIOS 4-15 Intel <R> Virtualization T echnology (*A vailable when supported by the CPU.) Select Enabled to use the feature of Virtualization T echnology to allow one platform to run multiple operating systems and applications in independent partitions, creating multiple "virtual" systems in one physical computer .
4-16 X7DVL-3/X7DVL-i User's Manual Interrupt This setting allows you to select the IRQ (interrupt request) for serial port B. The options are IRQ3 and IRQ4. Parallel Port This setting allows you to assign control of the parallel port. The options are Enabled (user de fi ned), Disabled and Auto (BIOS-or OS- controlled).
Chapter 4: BIOS 4-17 ECC Event Logging This setting allows you to Enable or Disable ECC event logging. Mark DMI Events as Read Highlight this item and press <Enter> to mark the DMI events as read. Clear All DMI Event Logs Select Y es and press <Enter> to clear all DMI event logs.
4-18 X7DVL-3/X7DVL-i User's Manual X Hardware Monitor Logic Note: The Phoenix BIOS will automatically detect the type of CPU(s) and hardware monitoring chip used on the motherboard and will display the Hardware Monitoring Screen accordingly . Y our Hardware Monitoring Screen may look like the one shown on this page, P .
Chapter 4: BIOS 4-19 X Hardware Monitor Logic (*See the Note on Page 4-18.) CPU T emperature Threshold This option allows the user to set a CPU temperature threshold that will activate the alarm system when the CPU temperature reaches this pre-set temperature threshold.
4-20 X7DVL-3/X7DVL-i User's Manual X Hardware Monitor Logic CPU T emperature Threshold (*See the Note on Page 4-18.) This option allows the user to set a CPU temperature threshold that will activate the alarm system when the CPU temperature reaches this pre-set temperature threshold.
Chapter 4: BIOS 4-21 X IPMI (The option is available only when an IPMI card is installed in the system.) IPMI Speci fi cation V ersion: This item displays the current IPMI V ersion. Firmware V ersion: This item displays the current Firmware V ersion.
4-22 X7DVL-3/X7DVL-i User's Manual OS Boot W atch Dog Set to Enabled to enable OS Boot W atch Dog. The options are Enabled and Disabled . Timer for Loading OS (Minutes) This feature allows the user to set the time value (in minutes) for the previous item: OS Boot W atch Dog by keying-in a desired number in the blank.
Chapter 4: BIOS 4-23 X Realtime Sensor Data This feature display information from motherboard sensors, such as temperatures, fan speeds and voltages of various components.
4-24 X7DVL-3/X7DVL-i User's Manual 4-5 Security Choose Security from the Phoenix BIOS Setup Utility main menu with the arrow keys. Y ou should see the following display . Security setting options are displayed by highlighting the setting using the arrow keys and pressing <Enter>.
Chapter 4: BIOS 4-25 Password on Boot This setting allows you to determine if a password is required for a user to enter the system at bootup. The options are Enabled (password required) and Disabled (password not required). 4-6 Boot Choose Boot from the Phoenix BIOS Setup Utility main menu with the arrow keys.
4-26 X7DVL-3/X7DVL-i User's Manual 4-7 Exit Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. Y ou should see the following display . All Exit BIOS settings are described in this section. Exit Saving Changes Highlight this item and hit <Enter> to save any changes you made and to exit the BIOS Setup utility .
Appendix A: BIOS POST Error Codes A-1 Appendix A BIOS POST Error Codes This section lists Recoverable POST (Power-On Self T est) Error codes for the Phoenix BIOS. Recoverable POST Errors When a recoverable type of error occurs during POST , the BIOS will display a POST code that describes the problem.
A-2 X7DVL-3/X7DVL-i User's Manual Notes.
Appendix B: Installing the Windows OS B-1 Appendix B Installing the Windows OS After all the hardware has been installed, you must fi rst con fi gure Intel South Bridge RAID settings before you install the OS and other software drivers.
B-2 X7DVL-3/X7DVL-i User's Manual B-2 Installing the Windows XP/2000/2003 OS to Systems without RAID Functions Insert Microsoft's Windows XP/2000/2003 Setup CD in the CD Driver , and the 1. system will start booting up from CD. Continue with the OS installation.
Appendix C: Installing Other Software Programs and Drivers C-1 Driver/T ool Installation Display Screen Notes : 1. Click the icons showing a hand writing on the paper to view the readme fi les for each item. Click a computer icon on the right of an item to install an item (from top to the bottom) one at a time.
C-2 X7DVL-3/X7DVL-i User's Manual Supero Doctor III Interface Display Screen-I (Health Information) C-2 Con fi guring Supero Doctor III The Supero Doctor III program is a Web-based management tool that supports remote management capability . It includes Remote and Local Management tools.
Appendix C: Installing Other Software Programs and Drivers C-3 Supero Doctor III Interface Display Screen-II (Remote Control) ( Note : SD III Software can be downloaded from our Web site at: ftp://ftp.supermicro. com/utility/Supero_Doctor_III/. Y ou can also download SDIII User's Guide at: http:// www .
C-4 X7DVL-3/X7DVL-i User's Manual Notes.
(Disclaimer Continued) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, .
デバイスSupermicro X7DVL-3 ServerBoardの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Supermicro X7DVL-3 ServerBoardをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSupermicro X7DVL-3 ServerBoardの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Supermicro X7DVL-3 ServerBoardの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Supermicro X7DVL-3 ServerBoardで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Supermicro X7DVL-3 ServerBoardを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSupermicro X7DVL-3 ServerBoardの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Supermicro X7DVL-3 ServerBoardに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSupermicro X7DVL-3 ServerBoardデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。