Swim'n Playメーカーend deckの使用説明書/サービス説明書
ページ先へ移動 of 18
ASSEMBL Y INSTRUCTIONS 12 ft. 15 ft. 18 ft. END DECKS Part # 420867 READ THROUGH AND UNDERST AND ALL THE STEPS T O THIS INST ALLA TION BEFORE A TTEMPTING TO INST ALL EITHER YOUR POOL OR YOUR DECK.
GENERAL T ake time to follow the instructions and do things right the fi rst time. Read all instructions prior to starting. Before you start, check to see that you have the correct number of parts. Use your parts list which is broken down by carton. The manufacturer reserves the right to revise, change or modify construction of their product.
3 Clear out and level the ground in the location where your deck is to be installed. Use the Assembly Drawings below for reference while assembling your deck (Note: ladder can be installed on either side). During assemly please note that the ledges on the pool are to be removed where the deck meets the pool.
4 2 IMPORT ANT : ONL Y HAND TIGHTEN SCREWS A T THIS TIME Elevate your two outside deck sections using either patio blocks or saw horses. Attach the Posts referring to the Close-up Illustrations below and on the following page for the proper assembly procedure for each location.
5 Finally , attach another Long Square Post for the Ladder on either side of your deck in the location illustrated for your deck on the prior page. Choose the location of your ladder depending on which side of the deck will provide the most convenient access to the pool.
3 IMPORT ANT : ONL Y HAND TIGHTEN SCREWS A T THIS TIME 6 Position the Bottom Support Channels (long “L” shaped pieces) at the bottoms of the Posts according to the illustration below for your size deck. Note the different sizes. (The illustrations are as viewing the deck from above with the Ladder to be installed on the left side.
7 4a IMPORT ANT : ONL Y HAND TIGHTEN SCREWS A T THIS TIME Where the Posts and the Bottom Support Channels join, attach Angle Support Bars. The illustrations below indicate Close-up illustrations show the proper assembly procedure for each location. Where One Angle Support Bar attach to the Post use the ½” Sheet Metal Screws.
8 4b IMPORT ANT : ONL Y HAND TIGHTEN SCREWS A T THIS TIME Where the Posts fasten to the deck, attach Angle Support Bars. The illustrations below indicate which of the Close-up illustrations at the bottom of this page and at the top of the next page show the proper assembly procedure for each location.
SMALL ANGLE SUPPORT BAR DECK CLOSE UP #13 LARGE ANGLE SUPPORT BAR CLOSE UP #12 DECK 5 IMPORT ANT : ONL Y HAND TIGHTEN SCREWS A T THIS TIME For the 15’ and 18’ Decks assemble the Center Patio to the already assembled deck sec- tions using the 1” Round Head Screws and Hex Nuts.
10 18’ END DECK 15’ END DECK 12’ END DECK LADDER 6 For the 12’ End Deck attach the two 75” Bottom Angles to the bottom of the Posts as shown.
11 In the locations marked “Location A” (see the previous page), attach Angle Support Bars to the top of the Post and Deck as illustrated in Close-up #16 at right. Also attach Angle Support Bars to the bottom of the Post and the Bottom Support Channel as illustrated in Close-up #17 at right.
12 7 Before continuing, make sure that all the Posts are perfectly straight and tighten all screws and nuts securely . Y ou may now remove the saw horse or patio blocks and allow your deck to rest on the ground. Attach your assembled deck to your pool as shown.
13 8 a) Assemble and mount the “Ground to Deck” Ladder to the deck using instructions packed inside it’ s carton. b) Assemble and mount In-Pool Ladder using instructions packed inside it’ s carton. FENSURROUND INSTRUCTIONS Use the illustrations below for reference during the assembly of the Fence Posts as described on the next page.
14 GENERAL ASSEMBL Y ILLUSTRA TION Use the General Assembly Illustration below for reference as you assemble the Fensurround. END POST OR CORNER POST ST ANDARD POST FENCE BRAKET INSERTED THROUGH POST Before assembling your pool, drill the required holes in the V erticals.
T ake the V erticals and attach two Fence Post Brackets to each V ertical using the 1/4 x 20 x 3/4” Screws and W ashers and Hex Nuts provided as shown.
16 Use the illustrations below for reference during attaching the sections of Fence to the Fence Posts as described on the next page. 12.
17 Using the illustration for your size deck on the previous page, assemble the Fence Postions. Note carefully the location for the different sizes. Attach the Fence portions to the Fence Brackets using the ½” Sheet Metal Screws as illustrated below .
W ARNING LEDGE PLACEMENT ENTRY POINT VIEW FROM INSIDE THE DECK LA TCH GA TE POST SELF CLOSING HINGE GA TE LA TCH BAR 18 Using the Latch, Latch Bar and Hinges as templates, drill the holes in the locations as illustrated at the bottom. Drill a 5/32 hole for the Latch Bar and Self Closing Hinges.
デバイスSwim'n Play end deckの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Swim'n Play end deckをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSwim'n Play end deckの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Swim'n Play end deckの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Swim'n Play end deckで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Swim'n Play end deckを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSwim'n Play end deckの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Swim'n Play end deckに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSwim'n Play end deckデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
