System SensorメーカーPDRP-1001の使用説明書/サービス説明書
ページ先へ移動 of 56
PDRP -1001 Series Deluge - Preaction Control Pa n e l Instruction Manual 3825 Ohio A venue St. Charles, IL 60174 1-800-SENSOR2 Fax: (630) 377-6495 PN 50734:D0 ECN 0 0-543 Document 50734 I56-933-01 04/.
Lim W arLg.p65 01/10/2000 An automatic fire alarm system –typically made up of smoke detectors, heat detectors, manual pull stations, audible warn- ing devices, and a fire alarm control with remote notification capability–can provide early warning of a developing fire.
Lim W arLg.p65 01/10/2000 WARNING - Several different sources of power can be con- nected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equip- ment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized.
NFPA Standards 4 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 NFP A Standards This control panel complies with the fo llowing NFP A standards: •N F P A 1 3 - Sprin kler Systems •N F P A 1 5 -.
Table of Contents PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 5 T able of Contents NFPA Standards..................... ............ .............. .............. ........... .............. .............. ...... 4 NFPA Standards ............... .
Table of Conten ts 6 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Setup and Configuration... .............. .............. ........... ............... .............. ........... ..... 25 Transmitter Module - 4XTM ................ .............. .
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 7 1. Product Description Overview The PDRP-1001 Series Deluge - Preact ion Control System has been desi gned as a control center for use in single- and dual-hazard deluge an d preaction applications.
1. Product D escription Circuits 8 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Circuits Input Circuits Initiating D evice Circuit #1 (St yle B/D) Initiating D evice Circuit #2 (St yle B/D) W ate.
Control Panel 1. Product Description PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 9 Control Panel Figure 1 Control Pane l SW1 TB1 TB2 TB 3 TB4 JP1 GEN AL M2 SUPV 1 SUPV 2 GEN AL M1 J4 J5 J7 J8 OP.
1. Product D escription DIP Switch Functions 10 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 DIP Switch Functions The table below describes th e DIP switch functions. For a more detai led explaination see "Setting Mode of Operation" on p age 28.
Options 1. Product Description PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 11 Remote Annunciator - RZA-4X The Remote Annunciator mounts on a standard single-g ang box, and provides LED indication of the same functi ons as the Zone Relay Module.
1. Product D escription Specifications 12 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Specifications AC Power PDRP-1001 and PDRP-10 01A: 1 10/120 V A C, 50/60 Hz, 1.2 amps PDRP-1001E: 220/240 V AC, 50/60 Hz, 0.6 amps W i re size: minimum #14 A WG wi th 600V insulation Battery (lead acid only) Maximum Charging Circuit: 27.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 13 2. Installation Cabinet Mounting Carefully unpack t he system and check for shipping damage. Select a suitable location in a cl ean, dry , vib ration-free environment that is not subject to extreme temperatures.
2. Installation Cabinet Mounting 14 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 The figure below shows t he exterior dimensio ns and mounting h ole locations fo r the cabinet backbox and dimensi.
Installing Option al Voltmeter/Amme ter 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 15 Installing Optional V oltmeter/Ammeter T o monit or battery voltage and batte ry charging current, a 4XMM Meter Mod ule is required.
2. Installation Power Connections 16 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Power Connections W ARNING: Do not apply any type power to this control panel until all connections have been made and verified. AC Connections Disconnect (open) the circuit br eaker in the AC main breaker pa nel and tag it “Out of Service”.
Power-limited Wiri ng Requirements 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 17 Observe polarity when connecting t he batteries. Connect the b attery cable (p/n 75203 or 752 02, depending on terminal size of b attery) to terminal J9 on t he main circuit board using the plug-i n connector provided.
2. Installation Initiating Device Circuits 18 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Initiating Device Circuits The control panel provides four (4) In itiating Device Circuits (#1, #2, #3 and #4) and they m ay be configured as either Style D (Class A) or Style B (Class B).
Initiating Device Circuits 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 19 Four-Wire Smoke Detector Connections A maximum of 200mA is available from the 24VDC Resettab le Power circuit on TB1 (+24VR terminals).
2. Installation Output Circuits 20 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Output Circuits Notification Appliance Circuits The control panel provides two Style Z (Class A) or Style Y (Class B) Notification Appliance Circuits, which are supervised and power-lim ited.
Output Circuits 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 21 Releasing Circuits CAUTION: To prevent accidential discharg e, connect releasing devices after initial panel tests are completed. The control panel provides two Style Y (Class B) Releasing Circuits, which are nonpower-limited.
2. Installation Powering External Devices 22 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Alarm Relay Circuit One Form-C dry contact alarm relay is provided in the basic panel for controll ing supplementary devices. Contacts are rated 2 amps at 30 VDC and 0.
Optional Modules 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 23 Optional Modules Overview The control panel has two modul e connectors - J5 (upper position) and J8 (lower position). Three mo dules are available for the panel and they can be used in any combination, inclu ding duplicate modules.
2. Installation Optional Modules 24 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Installation - Lower Position T o install eith er the 4XTM, 4XZM or 4XLM module in the lo wer position follow these instructions: Figure 14 Module Installati on - Lower Position Step Action 1 Cut jumper ‘OP T2’ on main circuit board.
Optional Modules 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 25 Setup and Configuration Transmitter Module - 4XTM Connect a Remote Alarm circuit, Re mote Trouble circuit or a Municipal Box to the Transmitter Module as shown below .
2. Installation Optional Modules 26 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Zone Relay Module - 4XZM Note: The P AR-3 includes one (1) Zone Relay Module ( 4XZM). Relay #1 through #4 on thi s module will activate with outputs #1 t hrough #4. For non-latching (silenceable) relay operation, cut the jumper “LA TCH”.
Optional Modules 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 27 LED Interface Module - 4XLM Connect the terminals on TB1 of th e LED Interface M odule to the correspon ding terminals of the RZA- 4X Remote Annunciator . Make wiring connections with system power off.
2. Installation Setting Mode of Operation 28 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Setting Mode of Operation Select operati ng mode by setting th e SW1 DIP switches as described bel ow . After any changes are made to the confi guration of the switches, the panel mu st be reset.
Setting Mode of Operation 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 29 Discharge Timer Select the desired discharge timer setting by setting DIP Switches 3, 4 and 5 accordingly . • For NFP A 13 and 1 5 applications t imer must be set to “Di sabled”.
2. Installation Power-Up Procedure 30 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Power-Up Procedure W ARNING: Prior to energizing this panel, noti fy all perso nnel and auth orities, including any personnel who may be working on , around, or near this unit.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 31 3. System Operation System Status LEDs Alarm, T rouble and Supervisory LEDs will flash on and off until the event(s) has been acknowledged (TONE or ALARM SILENCE), at which point the LED will illuminate steadily .
3. System Operation Control Switches 32 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Control Switches Figure 22 Control Panel Switches T one Silence - Pressing this switch acknowledges alarms, tr oubles and supervisories. The pa nel has alarm and trouble resound with LED flash of new conditions.
Piezo 3. System Operation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 33 Piezo The piezo (local buzzer) generates different tone patterns for dif ferent event conditi ons: • Alarm - Generates a steady tone, no pu lse. • T rouble - Pulses one second on, one second off.
3. System Operation Last Event Recall 34 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Last Event Recall Last Event Recall allows the user to display the previous panel status. The Last Event Recall makes use of the four panel switches as follows: 1.
System Events 3. System Operation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 35 Single Zone in Alarm (Cross Zone) Condition Upon actuation of a single-zone initiating devi ce, a red alarm LED will illuminate to ind icate whether Zone 1 or Zone 2 is in alarm.
3. System Operation System Events 36 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Notes.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 37 Appendix A: Secondary Power Calculations Standby Battery Requirements The Standby Battery Current obtained in the table below represents the amount of current that must be supplied by the secondary power source (batteries) to sustain control panel operation for one hour .
Appendix A: Secondary Power Calculations Calculating the Battery Capacity 38 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Calculating the Battery Capacity Use this table to determine the battery capacity required by the s ystem.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 39 Appendix B: Compatible Devices T wo-wire Smoke Detectors, UL Listed Use the two-wire detectors listed below . T able 3 T wo-wire Smoke De tectors Detector Model Identifier T ype Base Model Identifier Standby Current (mA) Detectors per Zone System Sensor 1400 A I onization n/a n/a 0.
Appendix B: C ompatible Devices Four-wire Smoke Det ectors, UL Listed 40 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Four-wire Smoke Detectors, UL Listed Use the four-wire detectors listed below .
Notification Appliances, UL Listed Appendix B: Compatible Devices PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 41 Notification Appl iances, UL Listed Control panels suppling Special A pplication (FWR, Fi ltered) power must use the Notification App liances listed below .
Appendix B: C ompatible Devices Notification Appliances, UL Listed 42 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 T able 6 Notification Appliances System Sensor SP101R24M Speaker/ Strobe, 5” s.
Door Holders, UL Listed Appendix B: Compatible Devices PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 43 Door Holders, UL Listed Use the Door Holders listed below .
Appendix B: C ompatible Devices 24 VDC Relays, UL Listed 44 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Notes.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 45 Appendix C: NFP A Standard-Specific Requirements Minimum System Require ments The control panel has been designed for use in commer cial, industria.
Appendix C: NFPA Standard-Specific Requirements Digital Al arm Communicator/Transmit ter - Noti-Fire 911AC 46 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Digital Alarm Communicator/T ra nsmitter.
Universal Digital Alarm Communicator - 411UDAC Appendix C: NFPA Standard-Specific Re quirements PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 47 Universal Digital Alarm Communicator - 41 1UDAC The following figure illustrates an example of Central Station/Remo te Station Receiver or Protected Premises Receiving Unit reporting using a 41 1UDAC.
Appendix C: NFPA Standard-Specific Requirements Local Energy Municipal Box 48 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Local Energy Municipal Box Using the 4XTM T ransmitter Module for connection to a Local Energy Municipal Box. • The Municipal Box circuit supervises for ground fau lts and opens (i.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 49 Remote Station Receiver - RS82-9 Using the 4XTM T ransmitter Module for connection to a Fire•Lite RS82-9 Remote Station Receiver . • Intended for connection to a polar ity reversal circuit of a remote station r eceiving unit having compatible r atings.
Appendix C: NFPA Standard-Specific Requirements Remote Station Receiver - RS82-9 50 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 Notes.
PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 51 Appendix D: T esting & Maintenance Te s t i n g Inspection Perform the following prior to applying power to the system. • Check the actual wiring hookup with the wiring diagrams. • Insure that no pieces of wire have fallen into the circuitry .
Appendix D: Testing & Maintenance Troubleshooting 52 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 T able 9 T roubleshooting T able Symptom Problem Solution AC Power LED ON System trouble LED ON Circuit trouble LED ON Notification a ppl iance circuit trouble 1.
Index PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 53 Index Numerics 110/120 VAC 12 220/240 VAC 12 411UDAC 45, 47 4XLM LED Interface Module 11, 23 4XMM Meter Module 11, 15 4XTM Transmitter Module.
Index 54 PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 inspection 51 interconnect wire, battery 30 Interface Module 11 interruption of circuits 34 J J1 connector 13, 14 J2 Connector 15 J3 Connecto.
Index PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 55 resettable power 19, 22 resistance, allowable 19 resistor 47 resound 32 reverse polarity 25 reverse polarity circuit 10 reverse polarity loop.
Limited W arranty System Sensor ® warrants its products to be free from defe cts in materials and workman- ship for eighteen (18) mo nths from the da te of ma nufacture, unde r normal use and ser- vice. Products are date stamped at time of manufacture.
デバイスSystem Sensor PDRP-1001の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
System Sensor PDRP-1001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSystem Sensor PDRP-1001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。System Sensor PDRP-1001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。System Sensor PDRP-1001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
System Sensor PDRP-1001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSystem Sensor PDRP-1001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、System Sensor PDRP-1001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSystem Sensor PDRP-1001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。