TanakaメーカーTCS-3401の使用説明書/サービス説明書
ページ先へ移動 of 20
Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: T T T T T CS-3401 CS-3401 CS-3401 CS-3401 CS-3401 CHAINSAW CHAINSAW CHAINSAW CHAINSAW CHAINSAW P/N 29356 Date 04-20-01 Supplier T o The Outdoor P ower Equipment Industry ISM, Inc .
www.tanakapowerequipment.com 1 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Before using this unit: • Read the operator’s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment.
www.tanakapowerequipment.com 2 custsvc@tanaka-ism.com Owner’s Manual TCS-3401.
www.tanakapowerequipment.com 3 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 2. Warnings and safety instructions Operator Safety WARNING! This chain saw is designed especially for tree care and surgery. Only persons trained in tree care and surgery may use this saw.
www.tanakapowerequipment.com 4 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 3. Assembly procedures NOTE! Slightly move the bar back and forth and make sure the chain tension boss (4) fits into the hole (5) in the bar properly. 4. Confirm the direction of saw chain (1) is correct as in the figure, and align the chain on the sprocket.
www.tanakapowerequipment.com 5 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Alwa ys run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel.
www.tanakapowerequipment.com 6 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 CHAIN OIL (Fig. 2-1 B) Fill chain oil reservoir (2). Always use good quality chain oil.
www.tanakapowerequipment.com 7 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Chain brake operation (Fig. 2-5) Chain brake (1) is designed to activate in an emergency such as kick-back action. Please check to verify that it works properly before use.
www.tanakapowerequipment.com 8 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 WARNING! Never use the saw with only one hand. You cannot control the saw properly and you may lose control and injure yourself severely. Keep the saw body close to your body to improve control and reduce strain.
www.tanakapowerequipment.com 9 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 WARNING! Always observe the general conditions of the tree. Look for decay and rot in the trunk which will make it more likely to snap and start to fall before you expect it.
www.tanakapowerequipment.com 10 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 LIMBING Limbing is removing the branches from a felled tree. WARNING! A majority of kickback accidents occur during limbing.
www.tanakapowerequipment.com 11 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 THICK LOG, LARGER THAN GUIDE BAR LENGTH Begin by cutting on the opposite side of the log. Pull the saw towards you followed pre vious procedure. (Fig. 2-7J) If the log is lying on the ground make a boring cut to avoid cutting into the ground.
www.tanakapowerequipment.com 12 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 In the carburetor, fuel is mixed with air. When the engine is test run at the factory, the carburetor is basically adjusted. A further adjustment may be required, accord ing to climate and altitude.
www.tanakapowerequipment.com 13 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Cleaning the air filter Remove the air filter cover and the filter (1). Rinse it in warm soap suds. Check that the filter is dry before reassembly. An air filter that has been used for some time cannot be cleaned completely.
www.tanakapowerequipment.com 14 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Guide bar (Fig. 3-5) Before using the machine, clean the groove and oiler port (1) in the bar with the special gauge offered as an optional accessory. Oiler port (Fig. 3-4) Clean the chain Oiler port (1) whenever possible.
www.tanakapowerequipment.com 15 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 LOWERING DEPTH GAUGES WITH A FILE 1) If you sharpen your cutters with a file holder, check and lower the depth. 2) Check depth gauges every third sharpening. 3) Place depth gauge tool on cutter.
www.tanakapowerequipment.com 16 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the unit.
www.tanakapowerequipment.com 17 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 6. Specifications.
www.tanakapowerequipment.com 18 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 Declaration of conformity Declaration de conformit6 Dichiarazione di conformita Konformitiitserkliirung Declaraci6n de conformidad Konformitetsdeklaration Tanaka Kogyo Co.
www.tanakapowerequipment.com 19 custsvc@tanaka-ism.com Owner’s Manual TCS-3401 IMPORTANT NOTICE THIS INFORMATION IS FOR THE US AND CANADIAN MARKETS ONLY.
デバイスTanaka TCS-3401の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Tanaka TCS-3401をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTanaka TCS-3401の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tanaka TCS-3401の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tanaka TCS-3401で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tanaka TCS-3401を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTanaka TCS-3401の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tanaka TCS-3401に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTanaka TCS-3401デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
