TANDBERGメーカー1000 MXPの使用説明書/サービス説明書
ページ先へ移動 of 280
User Manual Software version F5 D13722.05 June 2006 This document is not to be reproduced in whole or in part without permission in writing from:.
TANDBERG 1000 MXP ii Trademarks and Copyright All rights reserved. This document conta ins inform ation that is proprietar y to TANDBERG. No part of this publication may be reproduced, st ored in a re.
User Manual iii eCos eCos, the Embedded Configurable Operating S ystem. Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003 Red Hat, Inc. Copyright (C) 2002, 2003 John Dallaway Copyright (C) 2002, 2003 N.
TANDBERG 1000 MXP iv Disclaimer The information in this document is furnished for informational purp oses only, is subject to change without prior notice , and should not be construed as a commitment by TANDBERG.
User Manual v Environmental Issues Thank you for buying a product which contributes to a reduction in p ollution, and thereby helps save the environment. Our products red uce the n eed for travel and transport and thereby re duce pollution. Our products have either none or few consumable parts (chemical s, toner, gas, paper).
TANDBERG 1000 MXP vi Information for Recyclers As part of compliance with the European WEEE Directive, TANDBERG provides recycling information on request for all types of new eq ui pment put on the market in Europe after August 13th 2005. Please contact TANDBERG at recy cling@tandberg.
User Manual vii Operator Safety Summary Operator Safety Summary For your protection please read these safety instructions completely before you con nect the equipment to the power source. Carefully observe a ll warnings, precautions a nd instructions both on the apparatus and in thes e operating instructions.
TANDBERG 1000 MXP viii • The plug connecting the powe r cord to the product/po wer supply serves as the m ain disconnect device for this equipm ent. The powe r cord must always be easily acce ssible. • Route the power cord so as to avoid it bei ng walked on or pinched by items placed upo n or against it.
TANDBERG 1000 MXP x Table of Contents 1 Introduction ................................................................................................................... ............ 1 1.1 At a Glance ...................................................
User Manual xi 3.12.2 Conference Layout................................................................................................... 74 3.12.3 Terminal Names........................................................................................
TANDBERG 1000 MXP xii 5.4.4 Video Qua lity .......................................................................................................... 145 5.4.5 Call Se ttings ............................................................................
1 1 Introduction The TANDBERG 1000 MXP provide s essential video f eatures for face to face meetings for small groups and offices with the quality and reliability found in all TANDBERG equipm ent.
TANDBERG 1000 MXP 2 Disturbance from GSM mobile phones a nd Blackbe rry devices is eliminated by a noise filter. Video Quality Features which ensure hig h quality video include: Natural Video TF which provides a 60 field s per second true interlaced picture.
Introduction 3 PC Zoom which allows the native resolution PC image to be zoomed in/out with the remote control to get SXGA resolution. Users can display video and presentations in the best layout based on the situation.
TANDBERG 1000 MXP 4 1.1 At a Glance Camera The camera is an integrated part of the unit and is centrally placed just above the monitor. Monitor The Digital LCD displays the far-end a nd near-end videoconferenci ng sites in addition to the menu. Codec The codec is the heart of the system .
Introduction 5 1.2 Menu Structure The Menu is available for all users a nd contains all the functionality of the system. The Cont rol Panel contains all the settings of the system. Makin g changes to the settings will change the behavior of the system.
TANDBERG 1000 MXP 6 Note that the system features and menu se ttings may vary dependi ng on network selectio n and software package..
7 2 Inst allation Precautions: Never install communicati on wiring during a lightnin g storm. Never install jac ks for communica tion cables in wet l ocations unle ss the jack is specifically designed for wet locations.
TANDBERG 1000 MXP 8 2.1 Unpacking The TANDBERG 1000 MXP consi sts of the following items: Videoconferencing system with built-in camera Remote Control Batteries User Manual on CD P.
Installation 9 2.2 Connecting Cables 1. Power cable Connect the power supply to the DC in input on the system. Connect the power cable to the power supply. Connect the power cable to an electrical distribution socket. 2. ISDN cables Connect the ISDN cables to the ISDN connectors on the system.
TANDBERG 1000 MXP 10 3. Plug for headset (optional) The TANDBERG 1000 has a 2.5mm 3-pole mini-jack con nector at its left side marked with a headset symbol.
Installation 11 2.3 Monitor Configuration Power on Switch the system on by connecti ng the power cable to an electri cal distribution socket. After the system has performed a self-test ro utine, the Menu will be displayed on the monitor.
TANDBERG 1000 MXP 12 2.4 System Configuration The system must be configure d for each insta llation. Configuration settings can be made via the system menu. Navigate through the menu system using the arro w keys and OK. Remember to press the Sav e button on the bottom of each menu to save the c hanges.
Installation 13 5. Screen Settings The settings may be left unchanged if no spe cial needs are required. The display layout may be changed at any time using the Layout button on the remote control.
TANDBERG 1000 MXP 14 Remember to save any changes made in the menu b y selecting the Save button on the Menu line and pressing OK. * The International Name field is only vi sible if the system name contains Asian a nd non -Latin character text input.
15 3 General Use Wake up the sy stem When the system is not in use, it is in standby mode and the screen is black. Wake up the system by picking up the remote co ntrol. An incoming call or pressing any key on the remote cont rol will also wake up the system.
TANDBERG 1000 MXP 16 3.1 The Welcome Screen When the system is switched on, the welcome scre en will be displayed. The welcome screen presents the menu and displays your main cam era image in the background (display main camera is the default setting).
Administrator Settings 17 3.2 Using the Remote Control The system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arro w keys and press OK to navigate through the menus. The system’s most commonly used functions are al so accessible directly from the remote control.
TANDBERG 1000 MXP 18 in and out.* 12. Selfview displays your outgoing video. Press Selfview again to turn selfview off, see Selfview . 13. Use the Phone Book to store and recall video contacts for easy placement of calls, see Phone Book . 14. Use the red End Call key to end the current call.
Administrator Settings 19 The remote control (TRC 4)**: 1. Change video source. If possible, you will start open a Dual Stream. Press the video source button again to stop the dual stream.
TANDBERG 1000 MXP 20 presentation source. If the Presentation key is held down for 1 second then the Presentation video sources menu will appear, see Presentation Key . 12. Press OK/Menu to show the menu and to select menu items, see Navigation . 13. Use Zoom + and – to zoom the camera in and out.
Administrator Settings 21 3.2.1 Navigation Arrow keys and OK Navigate in the menu with the arrow key s on the remote control. The orange selector on screen show s the selected item. Press OK to select. Cancel key In the Menu, pressing Cancel (X) w ill hide the menu.
TANDBERG 1000 MXP 22 3.2.2 Selfview The term “Selfview” means the outgoing image. In a normal call using the main camera, this is the image of you. The Selfview button toggles the images between Far End, Selfview and Dual Video (if any). How to use Selfview : 1.
Administrator Settings 23 Example: You are using the system as a PC and get an incom ing call. When the setting “Use Screen as Local PC monitor” is On, you will keep your PC image displayed locally and the incoming call pops up in a PIP or as sm aller images in a 1+3 layout, depending on your system.
TANDBERG 1000 MXP 24 3.2.3 Picture Layout The layout of the screen can either be shown a s Pi cture in Picture (PIP) or Picture outside Picture (POP) when displaying more than one video imag e. The behavior of the Layout button is dependent on the Picture Layout setting in Control Panel – General - Screen Settings .
Administrator Settings 25 3.2.4 Mic Off To mute the microphone during a call, press the Mic off button. An on-scree n indicator appears in the upper right corner when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash.
TANDBERG 1000 MXP 26 3.2.5 Volume + and - Press the Volume key to adjust the volume leve l. An on-screen indicato r will show the current level..
Administrator Settings 27 3.2.6 Number and Letter keys Pressing a number key when outsi de a call will bring up the call m enu. When in a call, the number keys are used for Camera Presets. Press a n umber and go to the corresponding Camera Preset (see Camera Presets ).
TANDBERG 1000 MXP 28 3.2.7 Touch Tones To activate dialing touch tones during a call, press the Touch tone s button. Otherwise the nu mber keys will work as configured in the Num ber Key Mode, see Control Panel – Menu Settings – Number Key Mode. An indicator will let you know that Touch tones are en abl ed.
Administrator Settings 29 3.2.8 Presets and Extension Numbers When pressing a number key on the rem ote control, while in a call, the user can decide what shall happen.
TANDBERG 1000 MXP 30 3.3 On-screen Indicators The system has a number of icons signaling diffe rent settings: Microphone Off This indicator is shown when the microphone is turned off. Press the Mic off button again to turn the microphone back on, see Mic Off for details.
Administrator Settings 31 Telephone This indicates that there is a telephone p articipant in the conference. The displayed number indicate s how many telephone part icipants there are in the conference. Duo Video / H.239 This indicates that there is a Dual Vide o Stream sent from you (near end ).
TANDBERG 1000 MXP 32 3.4 Using the Menu Press the Menu button on the remote co ntrol to display the menu. The menu cont ains all functions needed in order to control the system.
Administrator Settings 33 3.5 Make a Call It is easy to make a call: 1. Press the green Call button on remote control an d Dial number 2. Press the green Call button again to initiate the call Display the call menu by either: 1. Select Make a Call from the menu, or 2.
TANDBERG 1000 MXP 34 3.5.1 Place a Call The TANDBERG system can make both Video calls and Telephone calls . A Call Type selector button is placed to the right of the number entry field. The button sho ws if it is a video call (default) or a telephone call .
Administrator Settings 35 Place the call by either: 1. Use the arrow button on the remote co ntrol to select the Place Call icon an d press OK, or 2. Press the green call button on the remot e control.
TANDBERG 1000 MXP 36 3.5.2 Call Settings The Call Settings specifies the quality of the call. Each call will be set up with the Default Call Settings if the settings are not altered.
Administrator Settings 37 3.5.3 SIP Services SIP enables you to use the features Add Call and Transfer even if your system doe sn’t have multipoint capabilities. To get t he SIP Services available, you hav e to make a call using SIP as your Net. (See Call Settings) 3.
TANDBERG 1000 MXP 38 3.5.4 Streaming Streaming lets you broadcast your meeting to particip ants on the web. The web participant s can listen to the meeting, see snapshots, but not parti cipate themselves. Snapshot s of current stream (if MultiSite), selfview, far end and DuoVideo streams are accessible via http.
Administrator Settings 39 more than 2 router hops. Streaming Source* Auto: Enables streaming o f both local and far end video. Selection of which site to be streame d is done using voice switching (the site that spe aks is streamed). Local: Only the local video will be streamed.
TANDBERG 1000 MXP 40 3.5.5 Dialing In From Outside the Enterprise Dialing in Without Being Registered to a TANDBE RG Gatekeeper The feature enhancement enables diali ng th rough a TANDBERG Gateke eper without being registered to it. This makes it easy to call in from a video system outside the enterprise.
Administrator Settings 41 3.6 Answer an incoming call How to answer an incoming call: To accept an incoming call, press the OK button or the green Call b utton on the remote control. Answering a call with the push-button The push-button on the front panel of the unit works as a connect button during an incoming call.
TANDBERG 1000 MXP 42 3.7 End Call How to end a call: Press the red End Call button on the remote control, or Press the Menu button on the remote control to displ ay the menu and select End Call.
Administrator Settings 43 3.8 Standby The system will automatically go to Standby mode when it is not in use. In standby mode, the screen(s) are black.
TANDBERG 1000 MXP 44 3.8.1 Delay Standby for 1 hour Delay Standby for 1 hour postpones the system fro m entering standby mode for 1 hour. This function is useful when using the monitors for a local presentat ion to prevent the system from automatically blanking the monitors.
Administrator Settings 45 3.8.2 Delay Standby for 3 hours Delay Standby for 3 hours postpones the automatic standby mode for 3 hours. This function is useful when using the monitors for a local presentat ion to prevent the system from automatically blanking the monitors.
TANDBERG 1000 MXP 46 3.8.3 Do Not Disturb To prevent the system from accepting any incomi ng calls, activate the Do Not Disturb function. The caller will hear a bu sy tone when calling t he system. The monitor will be black wh en Do Not Disturb is active, see figure below.
Administrator Settings 47 3.9 Phone Book The Phone Book is available via the Phone Book bu tton on the remote cont rol or from the Make a Call menu. Using the Phone Book is time saving and prevent s the user from inadvertently calling the wrong number.
TANDBERG 1000 MXP 48 The following information is available from the P hone Bo ok: Placed Calls Missed Calls Received Calls My Contacts Global Contacts.
Administrator Settings 49 3.9.1 Call Log The Call Log lists Placed Calls, Missed Call s and Re ceived Calls. That allows the user to see which calls that are made in the past. The lists contain a maximum of 30 numbers and the numbers are stored in these lists until the system is restarted.
TANDBERG 1000 MXP 50 3.9.2 My Contacts My Contacts are the locally stored contacts on t he system. This means that it is possi ble to add new contacts and edit or del ete existing contacts. My Contacts can store up to 200 contacts. How to make a call using My Contacts: 1.
Administrator Settings 51 The following functions are av ailable from My Contacts: Call Now New Contact Edit Contact Delete Contact Close.
TANDBERG 1000 MXP 52 3.9.2.1 Add New Contact The New Contact function is availabl e from My Contacts . Add a new contact to My Contacts by: 1. Select the New Contacts button to open the New Contacts dialog b ox. 2. Enter Name by using the letter keys on the remote control.
Administrator Settings 53 3.9.2.2 Edit Contact The Edit Contact function is available from My Contacts . How to edit a contact in the Local Phone Book: 1. Select the contact that is to be edited. 2. Press the left arrow on the remote contro l, followed by the down arrow until the Edit Contact ic on is selected .
TANDBERG 1000 MXP 54 3.9.2.3 Delete Contact The Delete Contact function is available from My Contacts . How to delete a contact: 1. Select the contact that is to be deleted. 2. Press the left arrow on the remote control, followed by the down arrow u ntil the Delete Contact icon is selected.
Administrator Settings 55 3.9.3 Global Contacts When selecting Phone Bo ok the phone book ope ns showi ng the Global Contacts* or the Corporate Directory** below the folders Placed Calls, Missed Calls, Received Calls and My Contacts. These contacts cannot be change d locally by the system, only from the management system.
TANDBERG 1000 MXP 56 3.9.3.1 Up one Level Global Contacts can be arranged in a tre e struct ure with several sub folders. Use the Up on e Level button to navigate up in the tree structure. When a search in the Global Phone Book is m ade by using the Search fun ction, only contacts matching the search text are displayed.
Administrator Settings 57 3.9.3.2 Search The phone book can cont ain an unlimited amount of global conta cts. Using search make s it easier to find the wanted contact. How to search in the Global Phone Book: 1. Select the Search icon. 2. Enter search text in the dialogue box that appears and press the OK button on the remote control.
TANDBERG 1000 MXP 58 3.9.3.3 Copy Contact to My Contacts The Copy Contact to My Contacts function is available from the Placed Call s, Missed Calls, Received Calls and Gl obal Contacts folders, see Phone Book for details. It may be wise to copy contacts t hat are often used to My Contacts.
Administrator Settings 59 3.10 Camera Control Manual Focus The focus on the TANDBERG 1000 MX P can be adjusted manuall y by rotating the focus ring on the camera lens.
TANDBERG 1000 MXP 60 3.10.1 Far End Control Far End Control allows you to control your conference partner’s camera. An example of when this feature could be especially helpful is if it is not possible to see wh at a participant at the far end is writing on their white board.
Administrator Settings 61 3.10.2 Picture Control Brightness Adjust Brightness from 1-98 Monitor Brightness Select Monitor Settings and adjust Monitor Brightness from 0 -16.
TANDBERG 1000 MXP 62 3.11 Presentation The Presentation Functionality in the system enabl es you to show other available video sources in addition to your Main Camera. This is perfect for meetings where you would like to sh ow a PowerPoint presentation, for example.
Administrator Settings 63 3.11.1 Presentation Key The quickest way to show a pre sentation is to use the presentation key on the remote control . The presentation key is used to start and stop a presentation. The presentation key will display PC (default*).
TANDBERG 1000 MXP 64 3.11.2 Presentation Menu The Presentation menu offers you all available video sou rces; Main Camera, PC, Document Camera, VCR, AUX and VNC. All these sources can be used a s Main Video Stream or Dual Video Stream (Duo Video / H.239).
Administrator Settings 65 3.11.3 PC Presenter (DVI/VGA Input) (Optional feature - not available on all system s) Users often have their present ations on a laptop that is brought into the meeting room. Remember to connect your PC to the codec befo re you press the Presentation button.
TANDBERG 1000 MXP 66 3.11.4 PC Soft Presenter and VNC (Optional feature) PC SoftPresenter is used to display PC image s on your system without usi ng a VGA cable (PC Presenter). The system and your PC must be connect ed to the same LAN. In addition, VNC (Virtual Network Computing) server software mu st be installed on the PC.
Administrator Settings 67 3.11.5 Dual Stream (DuoVideo TF /H.239) (Optional feature - not available on all system s) With Dual Stream you have the opportunity to show two different live video stre ams simultaneously, main video and one a dditional source.
TANDBERG 1000 MXP 68 3.11.6 Take New Snapshot The system can take a snapshot of your live vi deo. Snapshot is han dy when you are in a call with a system that does not support Dual Stream. Use Snapshot to show a snap shot of your presentation and continue the meeting with main camera.
Administrator Settings 69 3.11.7 Display Snapshot The system stores the last sent or received S napshot. The sn apshot is deleted automatically after the call. How to display snapshots: 1. To view a stored snapshot, first choose the Snapshot header. 2.
TANDBERG 1000 MXP 70 3.12 Services A Multipoint Control Unit (MCU) enables severa l sites to participate in the same conference. During an MCU confe rence, the status line will provide information about the conferen ce.
Administrator Settings 71 Example of MultiSite for mid- to low end systems. Note that t he illustrations may differ from the actual product. Using the system’s internal MCU, MultiSite TF * Most TANDBERG MXP systems have an optional b u ilt-in MCU, which is called MultiSite*.
TANDBERG 1000 MXP 72 Terminate Meeting Using an external MCU with limited Chair Control Support y ou may hav e the following services With an external MCU that does not support H.
Administrator Settings 73 3.12.1 Request Floor and Release Floor When requesting floor, your video will be broadcasted in full screen to all other participants in the conference. Request Floo r is useful when you want to speak or di splay something in front of all participants.
TANDBERG 1000 MXP 74 3.12.2 Conference Layout (Only supported by TANDBERG MultiSite*) With a TANDBERG MultiSite you can choose between the layouts: Auto Split, 4 Split, 5+1 Split and Voice Switched view. Auto Split displays all pa rticipants on the screen simultaneously.
Administrator Settings 75 3.12.3 Terminal Names Choose Terminal Names to see a list of the partici pants of the MultiSite c onference. Press Ca ncel to go back.
TANDBERG 1000 MXP 76 3.12.4 Chair Control (Not supported by TANDBERG MCU o r MultiSite) As chairman, you have access to more MultiSite Services. Select Chair Co ntrol to assume the role of chairman of the conferen ce. Select Release Chair to end the role as chairman.
Administrator Settings 77 3.12.5 Assign Floor and Release Floor from Participant Assign Floor allows the chairman to sel ect which of the conference participant s are to be broadcasted to all other participants.
TANDBERG 1000 MXP 78 3.12.6 View Site and End View (Not supported by TANDBERG MCU o r MultiSite) View Site allows you to view any participant in the conference regardless of wh o has the floor and chair.
Administrator Settings 79 3.12.7 Disconnect Participant Disconnect Participant allows the chairman to di sconnect any participant in the conference. In a multipoint call, this is equivalent to disc onnecting a participant from the end call menu.
TANDBERG 1000 MXP 80 3.12.8 Terminate Meeting Terminate Meeting allows the chairman to terminat e the conference altogethe r. In a MultiSite call, this is equivalent to pressing End All Call s from the end call menu.
Administrator Settings 81 3.12.9 More about MultiSite (embedded MCU) (Optional Feature*) Calling in to a MultiSite Any system can be part of a MultiS ite conference by calling in to a MultiSite. The dial-in numbers to the MultiSite depends of t he network that is used.
TANDBERG 1000 MXP 82 3.12.10 Text Chat While in an ISDN or IP call to another system suppo rting Text Chat (T.140), select Text Chat the Services Menu. Enter text in the displayed window. How to use Text Chat: 1. Choose Text Chat from the Servic es Menu to open the Text Chat window.
Administrator Settings 83 4 Control Panel The Control Panel contains the follo wing features: User Guide Diagnostics Audio Demo Restart Settings* Settings: General Call Qua.
TANDBERG 1000 MXP 84 4.1 User Guide The on screen user guide take s you through a quick step-by-step introduction to the video system. It gives the user basic skills in how to use the system.
Administrator Settings 85 4.2 Diagnostics Diagnostics allows testing of individual syste m components a nd displays the current system settings. Diagnostics contain: System Information Channel.
TANDBERG 1000 MXP 86 4.2.1 System Information Select System Information to view system numbers , line status, soft ware version, hardware serial number and other useful information. Press arro w key up and down to scroll in the System Information list.
Administrator Settings 87 4.2.2 Channel Status Comprehensi ve information about the call progre ss is available through the Ch annel Status window. This window indicates the vario us stages each B-channel goes through whil st establishing a connectio n.
TANDBERG 1000 MXP 88 4.2.3 Call Status Comprehensive informatio n about the call is available through the Call Status window. The m enu has two columns, one for transmitted an d one fo r received audio/video/data information.
Administrator Settings 89 4.2.4 System Selftest The system performs a check to determine internal hardware integri ty. System Selftest is useful when you want to check if your network connection is active.
TANDBERG 1000 MXP 90 4.2.5 View Settings This window displ ays all the system settings. Us e the arrow key on the remote co ntrol to scroll through the list.
Administrator Settings 91 Document Camera VCR AUX VNC Split Screen Default Call Settings Call Type Network Bandwidth Restrict (5 6k) Auto H320 Bandwidth Auto H323 Bandwidth SIP Audio Settings Inputs M.
TANDBERG 1000 MXP 92 Brightness Video Name Main Cam AUX Doc Cam VCR PC VGA VNC Network Ty pe ISDN-BRIPRILeased E1T1External H331 ISDN Switch Type ETSI (Euro ISDN) Line1 Setup On Number1 Number2 SPID1 .
Administrator Settings 93 Gateway Ethernet Speed DNS Settings H.323 Settings E.164 Alias Use Gatekeeper Gatekeeper IP H.323 Prefix Advanced H.323 Settings RSVP NAT NAT Address QoS IP Precedence Audio Video Data Signaling IP Type of Service (TOS) Diffserv Audio Video Data Signaling IEEE802.
TANDBERG 1000 MXP 94 Data Port 1 Baud rate Parity Data bits Stop bits Mode Data Port 2 Baud rate Parity Data bits Stop bits Mode * The Settings available will vary within the MXP system r ange depending on system and what software options installed.
Administrator Settings 95 4.2.6 IP Address Conflict Check The system will give a warning if there is an IP conflict. The user may initiate this check by selecting IP Address Conflict Che ck.
TANDBERG 1000 MXP 96 4.2.7 Warnings Any warnings registered by the system will be displayed in the Warnings me nu. Open a warning in the list to get more information about the warning.
Administrator Settings 97 There is something wrong with the Leased E1/T1 line (Blue alarm). Please che ck your network connection. (1 92) There is something wrong with the Leased E1/T1 line (Yellow alarm). Please check your network connection.
TANDBERG 1000 MXP 98 4.3 Audio Demo TANDBERG systems are desi gned to improve audio quality during a video co nference – as if the person is in the same room! Demonstrate the high quali ty Audio of your system by pressing the Audio De mo button at the bottom of the Control Panel menu.
Administrator Settings 99 4.4 Restart Restart the system by pressing the Restart butt on. You are prom pted with a dialog box saying: Do you want to restart the system? Press OK to restart, press Cancel (X) to abort.
TANDBERG 1000 MXP 100 5 System Settings The Control Panel contains all the settings of the syst em. Making changes to the settings will change the behavior of the system.
Administrator Settings 101 5.1 General Settings When installing the system, go through the Gene ral Settings menu to ensure that you have the right settings for your syste m , see System Configuration.
TANDBERG 1000 MXP 102 5.1.1 Language The system supports 16 dif ferent languages for its on-screen men us; English, German, French, Norwegian, Swedish, Italian, Spanish, P ortuguese, Russian, Finnish, Chinese Simplified, Chinese Traditional, Japanese, Korean, Thai and Arabic.
Administrator Settings 103 5.1.2 System Name System Name identifies the sy stem: On the welcome page. During an MCU conferen ce call. When using the Web-interf ace. When the codec is acting as an SNMP Agent. Towards a DHCP serve r.
TANDBERG 1000 MXP 104 5.1.3 International Name If the System Name contains Asian and non-Latin cha racter text input, the International Name using Latin characters only , must be specified as well. This is in order to make other systems understand the system na me.
Administrator Settings 105 5.1.4 Auto Answer The auto answer setting decides whether an incomin g call is put through automatically or manually. On The system will automatically answer al l incoming calls. On+Mic Off The system will automatically answer all incomin g calls and switch the microphone off when the call is connect ed.
TANDBERG 1000 MXP 106 5.1.5 Phone Book Settings Corporate Directory On The Corporate Dire ctory is available in the menu. Off The Corporate Dire ctory is hidden from the menu and is unavail able for users. IP address Enter the IP address of the management system that provides the Phone Boo k.
Administrator Settings 107 5.1.6 External Services Settings External Services On When set to On External Services are available. Off When set to Off External Services are unavailable. IP address Enter the IP address of the service provider for Extern al Services.
TANDBERG 1000 MXP 108 5.1.7 Permissions Permissions contains settings for incoming tel ephone Calls, Far End Control, Remote Software Upgrade and Fallback to T elephony. Access Code An access code will help you control the use of the system. All users must enter a code to identify themselves and the call will be cha rged on thei r account.
Administrator Settings 109 Fallback to Telephony When dialing a number and the system fails to place a video call to the number dialed, the system will attempt to place a telephone call if Fallback to Telephon y is enabled. On Enables fallback from video calls to telephone call s.
TANDBERG 1000 MXP 110 5.1.8 Screen Settings Auto Layout On If Auto Layout is On the system will change layouts automatically depen ding on the number of participants in a call and if you have a dual video stream or not. Please refer to Layout for more information.
Administrator Settings 111 Picture in Picture (PIP) Pressing the Layout button on the remote will result in an extra picture in smaller view (Picture in Picture). Press the Layout button to move it around in the corners of the screen and finally hide it.
TANDBERG 1000 MXP 112 Example of 1+2 Picture outside Picture (wide screen). Example of 1+3 Picture outside Picture (wide screen). Note that the following menu settings do not apply for all TANDBER G MXP systems. Please refer to the actual menu page on your system.
Administrator Settings 113 Wide screen VGA or TV monitor in Normal (stretched) mode. Wide screen VGA or TV monitor In Wi de (native) mode. VGA Out Quality* The supported range of VGA form ats will be optimized for the VGA display monitor based on the source image.
TANDBERG 1000 MXP 114 VGA Out Quality for Wide XGA: If VGA Monitor Format is set to Wide, PC Picture Format is set to Normal, VGA Out Quality is set to Auto, the layout on the monitor is either full s.
Administrator Settings 115 5.1.9 Software Options The system requires a valid option key to activa te MultiSite and/or Presenter functionality. In order to activate additional bandwidth, you need to enter a bandwidth key. A restart of the syst em is required after entering a new option a nd/or bandwi dth keys.
TANDBERG 1000 MXP 116 5.1.10 Date and Time Settings NTP IP This is the NTP time server address from whi c h the system can get updated time information. See IP Services for more details. Auto The NTP IP will be provided by the DHCP server. Manual The NTP IP address is set manually.
Administrator Settings 117 5.2 Menu Settings Menu Settings contain the settings: Input Editor Language Menu Timeout In Call Balloon Help Number Key Mode Administrator Password .
TANDBERG 1000 MXP 118 5.2.1 Input Editor Language When the Input Editor Language is set to Chinese, Korean or Japanese the user will be able to enter Chinese / Korean / Japanese characters into an input field like the System Name or Phone Book, using the remote control.
Administrator Settings 119 5.2.2 Menu Timeout In Call The Menu appears on the bottom line of the screen. Set Menu Ti meout In Call to On if you want the menu to time out automatically when you are in a call. On The menus will time out automatically after 15 seconds if there is no activity on the remote control.
TANDBERG 1000 MXP 120 5.2.3 Balloon Help It is possible to enable / disable the ballo on help window. On Choose On if you want help text windows to appear.
Administrator Settings 121 5.2.4 Number Key Mode When pressing a number key on the rem ote control, while in a call, the user can decide what shall happen.
TANDBERG 1000 MXP 122 Settings for Remote Co n trol Nu mber Keys while in a call: Add Call While in a call, the Call Menu will automatically app ear when a number key is pressed on the remote control.
Administrator Settings 123 If you have no stored presets on y our system, you are likely not to use presets. Therefore the presets option is not present in the dialog box. Press arrow key to navigate in the list. Press OK on the remote control to select the desired ent ry.
TANDBERG 1000 MXP 124 5.2.5 Administrator Password It is recommended to put an Administrator Passw ord on the system. The Administrator Password can be maximum 5 digits long. The Administrator Password dialog box will pop up when you choose Settings from the Cont rol Panel.
Administrator Settings 125 5.2.6 Kiosk Mode Settings Kiosk Mode In Kiosk Mod e the system is set t o a simplified st ate where it can be contro lled with just the four arrow keys and OK.
TANDBERG 1000 MXP 126 If Language Menu is enabled you will first see the lan guage selection menu. Select lang uage and the Welcome Menu will be displayed wit h your desired language.
Administrator Settings 127 Kiosk Mode - Auto Dial* On The system will automatic ally dial to t he first contact in the Phone Book when he handset is lifted. If this contact is busy, t he system will call the seco nd number in the Phone Book and so on.
TANDBERG 1000 MXP 128 5.2.7 Startup Welcome Menu The Welcome Menu contains the Menu, System Stat us, your System Nam e and dial in numbers. On The Welcome Menu is sh own when the system wakes up from st andby mode. Off The Welcome Menu is not shown when the system wakes up from standby mod e.
Administrator Settings 129 Off Welcome text is not displayed on the wel come menu. Welcome Text You can change the welcom e text to any text you like, instead of the default text. Remember that Display Welcome Text must be On to be able to edit the welcome text.
TANDBERG 1000 MXP 130 5.2.8 Icons The following indicator ico ns may be set to on or off: Mic Off Volume Off On Air Encryption Bad Network Telephone DuoVideo/H.
Administrator Settings 131 5.3 Presentation Settings Presentation Settings contain: H.239 Startup Video Source Presentation Source Snapshot Source Auto-Display Snapshot PIP Pla.
TANDBERG 1000 MXP 132 5.3.1 Presentation Start If your system has Dual Stream capa bilities, y ou can show two video streams at the same tim e (see also Dual Stream ). Presentation St art is Auto by default. This means that you will start Dual Stream (a second video st ream) automatically when starting a presentation.
Administrator Settings 133 5.3.2 H.239 H.239 supports transmission of two video st ream s. It combines elements of Duo Video and People+Content. If H.239 is disabled you will still be able to start TANDBERG Dual Video Stream* Enabled Enables H.239 Disabled Disables H.
TANDBERG 1000 MXP 134 5.3.3 Startup Video Source The Startup Video Source is the video source on display w hen the system wakes up from standby mode. If you use Main Camera as star t up source, the system will start with Main Camera every time the system wakes up from stan db y, regardless of what the previous user was using.
Administrator Settings 135 5.3.4 Presentation Source The Presentation Source is connected to the Pr esentation button on the remote. Pressin g the Presentation button will put the Pr esentation Source on display. Presentation Source is PC by default*.
TANDBERG 1000 MXP 136 5.3.5 Snapshot Source When you take a Snapshot, you get a snapshot of the Snapshot Source. Current is the default Snapshot Source. This means that you take a sn apshot of the video source that is cu rrently active. You can change the Snapshot Source to any vi deo source.
Administrator Settings 137 5.3.6 Auto-Display Snapshot Select Auto to automatically display a received snapshot. Turn Auto-Di splay Snapshot Manual if you wish not to have them displayed on the sc reen when they are sent or received. The snapshots will be sent and received, but not di splayed.
TANDBERG 1000 MXP 138 5.3.7 PIP Placing PIP Placing lets you decide where the PIP shall appear. You can of course m ove the PIP with the Layout button on the remote anytime. Top Right PIP is placed in the Top Right corner. Bottom Right PIP is placed in the Bottom Right corner.
Administrator Settings 139 5.3.8 Presentation Rate When setting up a call with H.323 the ba ndwidth can be controlle d by the user. The Presentation Rate is expressed in p ercent of the Call Rate and shall reflect the H.323 Presentation Rate settings of the sender.
TANDBERG 1000 MXP 140 5.3.9 VNC Settings VNC Settings is necessary when usi ng a VNC present ati on. See chapter PC Soft Presenter and VNC for more information on how to use VNC.
Administrator Settings 141 5.4 Call Quality Call Quality contains the settings: Video Algorithm Audio Algorithm Max Upstream Rate Video Quality Default Call Settings.
TANDBERG 1000 MXP 142 5.4.1 Video Algorithm The system will automatically select the best video algorithm b ased on the video source and the capabilities of the remote system. Use this menu to disabl e video algorithms in case you have interoperability issues calling other systems.
Administrator Settings 143 5.4.2 Audio Algorithm The system will automatically select the bes t audio al gorithm based on the call rate and the capabilities of the remote system. Use this menu to disable audio algorithms in case you want to remove “low quality” audio , or if you have in teroperability issues calling other syst ems.
TANDBERG 1000 MXP 144 5.4.3 Max Upstream Rate (kbps) The Max Upstream Rate (kbps) defines the desired maximum transmitted call rate. This is to be able to limit the outgoing bandwidth whilst keeping th e maximum incoming bandwidth, especially useful for home offices wit h different upst ream and downstre am rates, typically ADSL.
Administrator Settings 145 5.4.4 Video Quality The different video sources need differe nt Video Quality Settings. Main Camera, VCR, AUX and Split Screen have Motion as default.
TANDBERG 1000 MXP 146 Sharpness*: Improved quality of detailed images and grap hics, lower frame rate, ideal for enhancing quality at lower bandwidths.
Administrator Settings 147 Native PAL: 4CIF (704 x 576 pixels), Digital Clarity 448p (576 x 448) iCIF (352 x 576 pixels), Natural Video CIF (352 x 288 pixels) QCIF (176 x 144 pixel.
TANDBERG 1000 MXP 148 5.4.5 Call Settings Default Call Settings are connected with Call Settings in the call menu. If you leave Call Settings unchanged when making a call, the syst em will use the default Call Settings in the call. In addition to the Call Settings Call Type, Net, Bandwidth and Restrict (56k), you also find settings for H.
Administrator Settings 149 Bandwidth Bandwidth decides the qu alit y of the video picture. When set to Auto the system will establ ish a connection using a proper bandwidth for the call, typically 384kbp s for ISDN calls and 768kbp s for IP calls.
TANDBERG 1000 MXP 150 Sub-address is used to address di ffe rent systems on the same ISDN line and is prima rily used in European Countries. LAN equivalent extension add ress o r TCS-4 is used to address different systems on a LAN, when dialing via a ga teway.
Administrator Settings 151 5.5 Audio Audio contains the settings: Headset Level Settings Alert Tones and Volume.
TANDBERG 1000 MXP 152 5.5.1 Headset Level Settings Headset mic It is possible to adjust the headset microphone input level according to the sen sitivity of the used headset. The on-screen audio level indicator will ma ke it easier to set the correct input level settings.
Administrator Settings 153 5.5.2 Alert Tones and Volume Video Call Alert Tone and Telephone Alert Tone To help distinguish between incoming video calls a nd ordinary telephone call s, it is recommended to use different ringing tones for video calls and telep hone calls.
TANDBERG 1000 MXP 154 5.6 Video Video contains the settings: MCU Status Line Web Snapshots Video Name.
Administrator Settings 155 5.6.1 MCU Status Line On The MCU / DuoVideo indicator will be disp layed and provide info rmation about the conference. Off The MCU / DuoVideo in dicator will not be displayed. Auto The MCU / DuoVideo indicator will be displayed for a few se conds and then timed out.
TANDBERG 1000 MXP 156 5.6.2 Web Snapshots The system is able to generate JPE G snapshots and provide them when requ ested (as ‘http get’ or via ftp). See Appendix 6 for descriptions of the possible snapshot files. On Snapshots generation is enabled.
Administrator Settings 157 5.6.3 Video Name As a default, the video inputs are given the name s Main Cam, PC, Doc Cam, VCR, AUX or VNC, dependent on what video sources ar e available on yo ur system.
TANDBERG 1000 MXP 158 5.7 Security Security contains the settings: Encryption Encryption Mode Passwords.
Administrator Settings 159 5.7.1 Encryption (Country specific) Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption (AES or DES), the call will be encrypted. If not, the call will proceed without encryption.
TANDBERG 1000 MXP 160 5.7.2 Encryption Mode Auto The system will try to use the most secure encryption - AES, dependent on the capabilities of the other si tes. For sites that do not support AES encryption, DES encryption will be tried. AES The system will try to use AES with 128 bits encryption when setting up calls.
Administrator Settings 161 5.7.3 Passwords Administrat or Passwo rd, IP Acce ss Passwo rd , Streaming Password, VNC Passw ord, Access Code and Remote Software Upgrad e password ar e duplicated from their re spective menus. Using the Security menu g ives you a quick way to change all pa sswords of the system.
TANDBERG 1000 MXP 162 5.8 Network The network menu contain: ISDN-BRI Settings LAN Settings Network Profiles.
Administrator Settings 163 5.8.1 ISDN-BRI Settings To make sure your system will work properly using ISDN-BRI, make the fo llo wing settings: 1. Set ISDN switch type 2.
TANDBERG 1000 MXP 164 Advanced ISDN Settings Sub address Using a sub address ena bles you to connect up to eig ht ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by usin g different sub addresse s. To call a terminal with a sub addre ss, separate the ISDN telephone nu mber and the sub addre ss with a ‘*’.
Administrator Settings 165 5.8.2 LAN Settings LAN Settings contain: IP Settings H.323 Settings SIP Settings Wireless LAN Settings SNMP Settings IP Services Quality of Service 802.
TANDBERG 1000 MXP 166 5.8.2.1 IP Settings Remember to restart the system after making cha nges to IP Settings. This can be done by selecting the “Save and Restart” at the b ottom of the IP setting menu. Changes in IP Settings menu will not have any effect until the system is restarted.
Administrator Settings 167 Ethernet Speed Auto The codec will auto-dete ct t he speed/duplex on the LAN. 10/Half The codec will conn ect to the LAN using 10Mbps spe ed/Half Duplex. 10/Full 10 Mbps speed/Full Duplex . 100/Half 100 Mbps speed/Half Duplex.
TANDBERG 1000 MXP 168 DNS Settings DNS Server 1-5 DNS Server defines the network addre sses for DNS servers. Up to 5 addresses may be specified. If the network addresses are unkno wn, please contact your administrator or Intern et Service Provider.
Administrator Settings 169 5.8.2.2 H.323 Settings E.164 alias This is the E.164 address of the system . The E.164 address is equivalent to a telephone num ber, sometimes combined with access code s. Valid characters are 0-9,* and #. When using a gatekeeper, the system will send a messag e to the gatekeeper containing both the E.
TANDBERG 1000 MXP 170 Gatekeeper Settings Gatekeeper Discovery Auto The sy stem will automatically try to register to any available gate keeper. If a gatekeeper responds to the request sen t from the codec within 30 seco nds this specific gatekeeper will be use d.
Administrator Settings 171 Multiple H.323 Aliases is set to Off. If set to Off, the system will register a si ngle H.323-IDs on the Gatekee per based on the following priority: • H.323 ID • International Name • System Name The default setting for Multiple H.
TANDBERG 1000 MXP 172 CallManager Settings CallManager IP This is the CallManager IP-address that is used if you specify H.323 Call Setup: CallManager.
Administrator Settings 173 Advanced H.323 Settings The Advanced H.323 Settings only have an effect if t hey are supported by your IP infrastructure. NAT NAT, Network Address Translation, is used whe n a PC and a videoconferencin g system are connected to a router with NAT suppo rt.
TANDBERG 1000 MXP 174 H.323 Ports Static When selecting static H.323 ports for TCP connections the ports 5555 to 5574 will be used for Q.931 and H.245 respe ctively. Dy n am i c The system will allocate which ports to use when opening a TCP connection.
Administrator Settings 175 5.8.2.3 SIP Settings Mode On Setting the SIP mode to on will enable the system for incoming and outgoin g SIP calls. Off Setting the SIP mode to off will disable incoming and outgoing SIP calls from the system. Display Name The Display name part of the SIP Addre ss (U RI) is usually a full name or system name.
TANDBERG 1000 MXP 176 Server Address The Server Address is the manually con figured address for the out bound proxy and regist rar. It is possible to use a fully qualified domain name, or an IP addres s. The default port is 5060 for TCP and UDP, but another one can be provided.
Administrator Settings 177 Draft-ietf-avt-rfc2032-bis-0 6.txt - Draft for advanced video signalin g including resolution and mpi. RFC 2190 RTP Payload Format for H.263 Video Stre ams RFC 2429 RTP Payload Format for the 1998 Versi on of ITU-T Rec.
TANDBERG 1000 MXP 178 5.8.2.4 Wireless LAN Settings SSID (Service Set Identification ) Example “WLANNETWORK”. Define s a local network id for this wireless re gion.
Administrator Settings 179 Use Key Select which of the keys s hown below you want to use. Key 1-4 The 64 -bit keys can consi st of a leading star (*) and 5 characters. The 128-bit key can consist of a leading star (*) and 13 characters. Start with a * and then the text.
TANDBERG 1000 MXP 180 5.8.2.5 SNMP Settings SNMP Settings SNMP Trap Host identifies the IP-address of the SNMP manager. SNMP (Simple Network Management Protocol, SNMP Ver 1) is used for m onitoring and co nfiguring of different entities in a network. The system's SNMP Agent resp onds to requests from SNMP Mana gers (a PC program etc.
Administrator Settings 181 5.8.2.6 IP Services NTP IP This is the NTP time server address from whi c h the system can get updated time information. This is a requirement for proper o peratio n if H.235 authentication is implemented. The Network Time Protocol (NTP) i s used to sync hronize the time of the system to a reference time server.
TANDBERG 1000 MXP 182 5.8.2.7 Quality of Service QoS Type Off No QoS is used. Diffserv Diffserv QoS method is used. Please see belo w for details. IP Precedence IP Precedence QoS method is used. Please see below for details. IP Precedence Video Used to define which priority audio, video, dat a and signalin g should have in the network.
Administrator Settings 183 Auto will provide the following priority: Audio 4 Diffserv Video Used to define which priority Audio, Video, Da ta and Signaling packets sho uld have in an IP network. The priority ranges from 0 to 63 for each type of packets.
TANDBERG 1000 MXP 184 5.8.2.8 IEEE 802.1x 802.1X The system may be connected to an IEEE 802.1x LAN network. Supported 80 2.1x protocols are EAP-MD5, EAP-PEAP and EAP-TTLS. The 802.1x authent ication are enabled by setting 802.1x Mode to On. On 802.1x authentication enabled Off 802.
Administrator Settings 185 5.8.3 Network Profiles This menu consists of 7 network profiles; a prefix and a suffix can be added for each p rofile. If you add a prefix/suffix to a profile, this prefix/su ffix will automatically be add ed in front/back of the number being dialed.
TANDBERG 1000 MXP 186 5.8.4 Restore Default Settings Restore Default Settings will restore all system setti ngs. Note that this will not affect your Call Directory information, Network Type, Li ne Setup numbers or your SPID numbers.
187 6 Peripheral Equipment Using the optional peripheral device s outlined in this chapter and the many others available, you will be able to build your own applications for us e with the system, thereby better integrating the system into your business environ ment.
TANDBERG 1000 MXP 188 6.1 Interfaces 6.1.1 Video 1 Video Input 1 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) inpu t, analog or digital.
Peripheral Equipment 189 Supported DVI cables: TANDBERG supports DVI-D Single -Link, DVI- A and DVI-I Single-Link format cables. DVI-D cables transmit digital T.M.D.S. signal s, DVI-A cables transmit analog VGA signal s and DVI-I cables can transmit either digital or anal og signals.
TANDBERG 1000 MXP 190 The TANDBERG 6000 MXP Profile and 3000 MXP Profile* systems are shipped with a PC cable with integrated audio : DVI-A Plug + 2*RCA Plug to VGA Plug + 3.5mm Stereo Plug, length 6m. PC cable, VGA - DVI with integrated audio Signal name CON.
Peripheral Equipment 191 RGB Return C5 6, 7, 8 RGB Coax Shield Outer Shield Ground Shell Shell Outer Shield Audio Left Centre Tip Audio Black Audio Right Ring Centre Audio Red Audio GND Gnd Sleeve Gnd Audio Shield PC cable, VGA - DVI with integrated audio * Applies to T3000 MXP Profile with new hardware.
TANDBERG 1000 MXP 192 VGA to DVI-A Cable Pinouts* : VGA to DVI-A cable male-male 5m black, maximum length 5m. No Item Description 1 Cable UL20276 3Coax*30#+IP*28#+5C*28#+AEB Black OD:7.0mm L-5000mm 2 Connecto r HDD 15P Male Black 3 Connecto r HDD 17P Male Black 4 Tube PE Tube Black OD:1.
Peripheral Equipment 193 6.1.2 Audio All audio inputs are active by default. For further information, refer to chapter Audio . Headset 1 headset connector, 2.
TANDBERG 1000 MXP 194 6.1.3 Network Ethernet: 1 x Ethernet (RJ-45 Jack) LAN interface (10/100 Mb) up to 768kbp s To connect the system to a LAN, use the Ether net cable provided b y TANDBERG (or a standard Ethernet cable).
Peripheral Equipment 195 6.2 Document Camera A document camera can be used for sho wing text, diagrams and a variety of graphical material as well as small three-dimensio nal objects. How to use a document camera with your system: 1. Connect the document camera to the Do c Cam input, if available, on the system.
TANDBERG 1000 MXP 196 6.3 DVD / VCR DVD/VCR Playback Mono For playback, connect a cable between Video Out on the VCR and Video In (VCR) on the system. Connect a cable between Audio Out on t he VCR a nd the Audio In (VCR) on the system. Choose VCR from the Presentation menu to activate the VCR in put.
Peripheral Equipment 197 6.4 Additional Cameras Extra fixed Cameras You can connect extra fixed camera s to your sy stem, for example, a whiteboard camera. Con nect the video output of the additional camera to one of the available Video inp uts on the system.
TANDBERG 1000 MXP 198 6.5 Additional Microphones If your environment is such that you require more than one microphone for you r room, e.g. you have a whiteboard at a distance from your table microphone, it is possible to con nect additional microphones to your system.
Peripheral Equipment 199 6.6 The TANDBERG DNAM and Speakers TANDBERG 6000 MXP Profile, T ANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro The TANDBERG Digital Natural Audio .
TANDBERG 1000 MXP 200 TANDBERG 6000 MXP Profile DNAM configuration Center Speakers + Integrated Stereo Speakers The DNAM Amplifier*: 3 x 50W continuous average Center Out put Power (load specified by DNAM Ce nter Speakers). 2 x 50W continuous average Stereo Output Powe r (load specified by TANDBERG Loudspeaker Stereo Kit).
Peripheral Equipment 201 The DNAM Loudspeaker Cabinet (Center Spe aker s)*: 3-way Center Speaker system Frequency range 50Hz - 2 0kHz 2 x 130mm low- and midrange loudspeakers, 8 ohm s nomi.
TANDBERG 1000 MXP 202 The Mini-DNAM Loudspeaker Cabinet*: The Mini-DNAM speaker cabinet specification: 2 * 15W Stereo Speakers, high quality Frequency range 100Hz - 20kHz Enclosed MDF spea.
Peripheral Equipment 203 6.7 Stereo Speaker Kit Note that the following applies only for system s with a stereo S/PDIF output. The Stereo Speaker Kit provides an pair of floor-s tanding lou dspeakers in addit ion to the built-in DNAM . Using these speakers will ena ble stereo func tionality in your system and thereby enhance the sound experience.
TANDBERG 1000 MXP 204.
Peripheral Equipment 205 6.8 Telephone Add-On The system has a built in audio bri dge* that can br ing in Voice over IP (VoIP) telephony or normal telephone sites using ISDN. Note that this requires a system with mix ed audio output (audio from local an d far end) and one audio input without integrated echo cancelli ng.
TANDBERG 1000 MXP 206 6.9 Dual Monitor Note that this requires a system with du al monitor video output..
Peripheral Equipment 207 6.10 XGA Monitors and Projectors (Optional) Some TANDBERG systems can be delivered with op tional single or dual TV/XGA monitors. It can also be connected to any DVI/VGA/PAL or NTS C display. Note that this requires a system with min imum one DVI-I output.
TANDBERG 1000 MXP 208 6.11 VESA Display Power Management Because of the tremendous amount of energy co ns umed by monitors when operating, the system will reduce power consu mption and extend monitor lifecycl e by suspending the (swit ch off) monitors and projectors when the syste m goes into sleep/standby.
Peripheral Equipment 209 6.12 Digital Monitor Power Management DMPM is monitor power management a pplied over the digital DVI interface. TANDBERG supports DMPM in softwar e F2 and above. Six monitor power stat es are defined. Monitor On Power state Transmitter (TANDBERG codec) and receiver (Moni t or) are powered and active.
TANDBERG 1000 MXP 210 6.13 Extended Display Identification Data (EDID) Extended Display Identification Data (EDID) is a VESA standard data format that will allow the system to communicate its ca pabilities, including vendor information like the supported VGA - formats and frequency range limits to a PC con nected to the XGA/DVI input.
Peripheral Equipment 211 Tested and verified monitors, EDID & Timing Listed below are some of the monitors TANDBERG h ave tested and verified against: ADI A715 Dell W1700 Dell W1900 EIZO L367 EIZO.
212 7 Appendices Appendices: Appendix 1: Technical Specification Appendix 2: Bandwidth Information Appendix 3: Environmental considerations Appendix 4: Guidelines for setting up rooms .
Appendices 213 Appendix 1: Technical Specification Technical Specification UNIT DELIVERED COMPLETE WITH: Wireless remote control, built-in camera, microphone, speakers, cables, 12.1" LCD screen, table-top stand. LCD SCREEN Wide view angle screen XGA resolution Auto or manual brightness BANDWI DTH H.
TANDBERG 1000 MXP 214 SVGA (800 x 600 pixels) VGA (640 x 480 pixels) WIDE RESOLUTIONS: w288p (512 x 288 pixels) w448p (768 x 448 pixels) receive only w576p (1024 x 576 pixels) w720p (1280 x 720 pixels) STILL IMAGE TRANSFER CIF, SIF, 4CIF (H.261 Annex D ), 4SIF, VGA, SVGA, XGA AUDIO STA NDARDS G.
Appendices 215 Intelligent Packet Loss Recovery (IPLR) H.245 DTMF tones in H.323 Cisco CallManager integration using ECS IP Address Conflict Warning Date and Time support via NTP Call Services IPv6 NE.
TANDBERG 1000 MXP 216 Appendix 2: Bandwidth Information for TANDBERG Endpoints Bandwidth information for TANDBERG endpoints Model 8000MXP, 7000MXP 6000MXP, Maestro Bandwidth Point to point ISDN / IP S.
Appendices 217 H.264 Up to 2Mbps Up to 2Mbps Picture Mode MultiSite VS, CP4, CP5+1 VS, CP4, CP5+1 Model 990MXP / 990NET MXP 880MXP / 880NET MXP Bandwidth Point to point ISDN / IP Standard: 1920 (IP on.
TANDBERG 1000 MXP 218 Appendix 3: Environmental Considerations Environmental considerations This section explains how to carry out basi c adjus tments and simple tests to ensure that you send and receive the best possi ble image and audio qualit y when using your system.
Appendices 219 Appendix 4: Guidelines for Setting up Rooms for Video Meetings Guidelines for setting up rooms for video meetings The following are a set of guidelines to consider when either building a video me eting room, or using an existing room for video meetin g.
TANDBERG 1000 MXP 220 How to prepare a typical room for video meetings : The illustration below shows the principles of a typical room designed to obtain the best results when using a video meeting system. If the system has a separate microphone , it shoul d be placed at the front of the table to ensure that all speech will be detected.
Appendices 221 Appendix 5: Security Security The system has several features both to prot ect from unauthorized use a nd system access: Access Code: When Access Code is enabled, the user will be as ked to enter an access code before he/ she is able to make a call.
TANDBERG 1000 MXP 222 By setting an IP Access Password on the s ystem, all access to the system using IP (Telnet, FTP and WEB) requires a pa ssword. This password can be enabled from telnet or da taport using the command: ippassword <ip-passwo rd>.
Appendices 223 backwards compatibility) with extended Diffie Hellma n key distribution via H.320, H.323 and Leased Line con nections. The TANDBERG AES implementation is validated as conforming to the .
TANDBERG 1000 MXP 224 Appendix 6: Using the File System Using the file system It is possible to access a file sy stem within the TANDBERG sy stem by using ftp: DOS- window: ftp <IP-address of system >, or Web- browser: ftp:// <IP-address of system> Description of the different files: all.
Appendices 225 Appendix 7: Web Interface Web Interface It is possible to access and maintain the system remotely via a local area network (LAN) using a standard Web-browser. Conne ct your syste m to a LAN with a Network cable. How to configure your system for web interface: 1.
TANDBERG 1000 MXP 226 Appendix 8: Connecting the System to PRI/T1 (Not available on all TANDBERG systems) Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1-inte rface using an Adtran T1 ESF CSU ACE or equivalent CSU, will allow up to 1.
Appendices 227 Appendix 9: Connecting the System to the Switched 56 Network Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adap ter Connecting the system to the SW56 net work using a Telesync Adapter is descri bed below.
TANDBERG 1000 MXP 228 Appendix 10: Connecting the System to ISDN using NT1 Network Adapters Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on t he system to the S-interface on your first NT1 network adapte r.
Appendices 229.
TANDBERG 1000 MXP 230 Appendix 11: TANDBERG Cameras TANDBERG Precision HD Camera (Available to TANDBERG 8000 M XP, 6000 MXP Prof ile, 3000 MXP Profile*, Maestro MXP and Edge 75/85/95 MXP) Pin-outs and Connectors 1.
Appendices 231 2. 12V DC Power In 3. HD Video Out, HDMI** 4. Codec – HD Video Out 5. Kensington Lock NOTE! The enclosed TANDBERG Camera Cable s must be used! Do not use other came ra cables as this might cause problem s with the tr ansfer of video signals from the Precision HD Camera.
TANDBERG 1000 MXP 232 The maximum length of the camera cable for mult iple cameras sup ported by TANDBERG is 20 m (65 ft). * Applies to T3000 MXP Profile with new hardware. ** Disabled when connected to a TANDBERG system using the TANDBERG Ca mera Cable.
Appendices 233 Top view:.
TANDBERG 1000 MXP 234 (Not available with TANDBERG 1000 M XP and set top systems) WAVE II Camera Pinouts and Connectors 8-PIN RJ (shielded modular jack): This connector is u sed for the power and control signals to the main camera.
Appendices 235 Pin-5 GND Pin-4 RXD (in) Pin-3 TXD (out) Pin-2 Presence (+12V in daisy chain) Pin-1 GND.
TANDBERG 1000 MXP 236 Dimensions Front view: Sid e view : Re ar view : Underside vie w:.
Appendices 237 Appendix 12: Remote Control (TRC3 / TRC4) Remote Control (TRC3 / TRC4) The TANDBERG remote control transmits IR -signals using the following parameters: Protocol Siemens SDA2208 Referen.
TANDBERG 1000 MXP 238 Remote Control key code map: Button codes Remote Co n trol (TRC 3) Remote Control (TRC 4) TANDBERG TRACKER Dec Hex Address Button name Address Button name Address Button name 0 0.
Appendices 239 33 21 0 OK 0 OK 34 22 0 CALL 0 CALL 35 23 0 END CALL 0 END CALL 36 24 0 PHONE BOOK 0 PHONE BOOK 37 25 0 MENU 0 MENU 38 26 0 CANCEL 0 CANCEL 39 27 0 0 40 28 0 LAYOUT 0 LAYOUT 41 29 42 2A.
TANDBERG 1000 MXP 240 Appendix 13: Cisco CallManager Registration Cisco CallManager registration Configuring an H.323 client on the CallManager 4.0 The registration of a H.323 client in CallM anager is supported on t he CallManager (CCM) 4. 0 software and forward.
Appendices 241 Appendix 14: Diagnostic Tools for IP Diagnostic Tools for IP To use these tools, will require u sing a PC and setting up a telnet session towards the sy stem. Q.931 To show Q.931 trace during a call you n eed to issue the comman d ‘syslog on’.
TANDBERG 1000 MXP 242 Function Port Typ e Gatekeeper Discovery (RAS) 1719 UDP Q.931 Call Setup 1720 TCP H.245 Range 5555-5574 TCP Video Range 2326-2341 UDP Audio Range 2326-2341 UDP Data/FECC Range 2326-2341 UDP Point-to-point + Duo Video Function Port Typ e Gatekeeper Discovery (RAS) 1719 UDP Q.
Appendices 243 Appendix 15: System Upgrade System Upgrade Before starting the software upgrade of the TA NDBE RG MXP system, please make sure to have the new software file, (for instance s0500 00F 30.pkg) and the Release Key for this software available.
TANDBERG 1000 MXP 244 The following page will now be di splayed: Figure 1 3. Enter the Release key in the ‘Release Key’ field and press the ‘Install Software’ button.
Appendices 245 A new page will now be displayed: Figure 2 4. Type in the path to where the new software file is stored, or sel ect the file by using the ‘Browse’ button. 5. The progress for the sw upgrade can be tracked by pressing the ‘telnet’ link in the help text box BEFORE pressing the install button.
TANDBERG 1000 MXP 246 5. Type in your IP password (def ault is “TANDBERG”) a s password. 6. Type ‘put <software file name> and press Ente r.
Appendices 247 Figure 3 5. Enter the release key for the system to be upgraded in the ‘Rele ase Key’ field. If no release key is given, the Far End System will use the prev iously stored release key if possible. This will work when upgrading from a main release to a dot relea se.
TANDBERG 1000 MXP 248 Appendix 16: Declaration of Conformity EC DECLARATION OF CONFORMITY MANUFACTURER: TANDBERG Telecom AS PRODUCT NAME: TANDBERG 1000MXP TYPE NUMBER: TTC7-12 DESCRIPTION: Video Confe.
Appendices 249 Appendix 18: Protocols Supported PROTOCOLS SUPPORTED TCP/IP - Transmission Control Protocol/Internet Protocol A set of networking protocols that provi des conn ectivity over LAN/WAN to any network com puter. HTTP - Hypertext Tran sfe r Protocol A protocol used to transfer information on the in ternet.
TANDBERG 1000 MXP 250 WAN – Wide Area Net work A communications network conn ecting geographically separated computers, printers, an d other devices. SSL - Secure Sockets Layer SSL is a proposed open st andard for establishing a secu re communications cha nnel to prevent the interception of critical information.
Appendices 251 Appendix 19: Cable Specifications TANDBERG MXP and Classic E ndpoints that support External Network External Network Pinout With respect to signals on the NET port: • For balanced signals a “0”=low voltage i s defined as terminal A positive with respect to terminal B.
TANDBERG 1000 MXP 252 Cable Specification V.35 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on cable at Codec en d: o Female 26 pin high-density DSUB with thumbscrews. • Connectors on cable at V.35-adapte r end: o Male 34 pin Winchester (AMP part number 2 01357-1 or equivalent).
Appendices 253 Cable Specification V.35/RS-366 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on cable at Codec en d: o Female 26 pin high-density DSUB with thumbscrews.
TANDBERG 1000 MXP 254 Cable Specification RS-449 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50 F.
Appendices 255 Cable Specification RS-449/RS-366 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50 F.
TANDBERG 1000 MXP 256 Cable Specification RS-530 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50 F.
Appendices 257 Cable Specification RS-530/RS-366 TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50 F2055 o.
TANDBERG 1000 MXP 258 Cable Specification RS-449 Cable to KIV-7 TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark.
259 8 Glossary # 199 AV1: External input for the TANDBERG/LOEWE monitor. 2nd monitor: The second monitor of yo ur videoconferencing syste m. The second monitor is normally placed on the right side of the first monitor.
TANDBERG 1000 MXP 260 B Bandw idth: Decides the quality of the video call. High bandwidth gives high q uality. C Call Control Data Triggered: Uses TxData, RxData and clock signals o nly.
Glossary 261 Diagnostics: Allows testing of individual system co mponents and displays the current system settings. Digital ClarityTF: Participants enjoy presentations o f ex ceptionally high quality resolution video. Disconnect site: As a Chairma n, you get the option Disco nnect site.
TANDBERG 1000 MXP 262 G G.711: Audio algorithm for normal qualit y audio (tel ephone quality, 3.1 kHz) The system will always have G.711 enabled. G.722: Audio algorithm for high quality audio (7 kHz). G.722.1: Audio algorithm for compressed high qu ality audio (7 kHz) G.
Glossary 263 M Main Camera: Your camera. Video input 1 Max call length: This feature will automatically end both incoming and outgoing calls when the call time exceeds the length specified. Max channels: Indicates the maximum number of channels the sy stem is allowed to use on the E1/T1 interface.
TANDBERG 1000 MXP 264 Network profiles: It is possible to define up to 6 network profile s, each consisting of name and call prefix, and 3 of them also include network selection. Non Standard Facility: The network provider may require service selection in your ISDN configuration.
Glossary 265 Request Floor: The MCU will broadcast the video in full screen to all other participants in the conference. If the MCU conf erence has a chai rman, a request will be sent to the the chairman. Restart: Restart s the system. Restore defaults: Re stores system settings to the factory defaults.
TANDBERG 1000 MXP 266 Streaming Announcements: The system will announce to the net wo rk that it is streaming. This enables a streaming client (e.g. a PC) to co nnect to the system's streaming session. Used by Cisco IP/TV. Streaming Pass word: Prevents unauthori zed access to the stre aming functionality.
Glossary 267 VNC: Virtual Network Computing. Voice Switched: The active site will be displayed in full screen during a MultiSite conference. W WAVE II Camera: Wide Angle View Camera - delivers the widest angle of view in the industry. Welcome menu: The welcome menu di splays the Menu when you are outside a call.
TANDBERG 1000 MXP 268 9 Index A Access Co de......................................86, 108 Additional mi cropho ne ............................. 198 Administrator Passwo rd ...........................124 Alert S peaker .................................
Index 269 Snapshot So urce ..................................... 136 Software Op tions ..................................... 115 Start up Video Source ............................. 134 System configuration ................................. 12 System Information .
デバイスTANDBERG 1000 MXPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TANDBERG 1000 MXPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTANDBERG 1000 MXPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TANDBERG 1000 MXPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TANDBERG 1000 MXPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TANDBERG 1000 MXPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTANDBERG 1000 MXPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TANDBERG 1000 MXPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTANDBERG 1000 MXPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
