TANDBERGメーカー7000 MXPの使用説明書/サービス説明書
ページ先へ移動 of 332
User Manual Software version F5 D13354.07 June 2006 This document is not to be reproduced in whole or in part without permission in writing from:.
TANDBERG 7000 MXP ii CAUTION! Avoid displaying the same images continuously over a long period of time on the monitors. Displaying the same images such as still images fo r a long time may cause after-image lagging. This may occur in the following two cases: 1.
User Manual iii Trademarks and Copyright All rights reserved. This document conta ins inform ation that is prop rietar y to TANDBERG. No part of this publication may be reproduced, st ored in a re tri.
TANDBERG 7000 MXP iv eCos eCos, the Embedded Configurable Operating S ystem. Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003 Red Hat, Inc. Copyright (C) 2002, 2003 John Dallaway Copyright (C) 2002, 2.
User Manual v Disclaimer The information in this document is furnished for informational purp ose s only, is subject to change without prior notice , and should not be construed as a commitment by TANDBERG.
TANDBERG 7000 MXP vi Environmental Issues Thank you for buying a product which contributes to a reduction in p ollution, and t hereby helps save the environment. Our products red uce the n eed for travel and transport and thereby re du ce pollution. Our products have either none or few con sumable parts (chemicals, toner, ga s, paper).
User Manual vii Information for Recyclers As part of compliance with the European WEEE Directive, TANDBERG provides recycling information on request for all types of new eq ui pmen t put on the market in Euro pe after August 13th 2005. Please contact TANDBERG at recy cling@tandberg.
TANDBERG 7000 MXP viii Operator Safety Summary Operator Safety Summary For your protection please read these safety instructions completely before you con ne ct the equipment to the power source. Carefully observe a ll warnings, precautions a nd instructions both on the apparatus and in thes e operating instructions.
User Manual ix • The plug connecting the powe r cord to the product/power sup ply serves as the main disconnect device for this equipm ent. The po we r cord must always be easily accessi ble. • Route the power cord so as to avoid it bei ng walked on or pinched by items placed upo n or against it.
TANDBERG 7000 MXP x Contact us If you have any questions, comments or suggestions, please se e the Onlin e Support sectio n at www.tandberg.net . It is also possible to send a fa x or mail to the attention of: Product and Sales Support TANDBERG P.
User Manual xi Table of Contents 1 Introduction ................................................................................................................... ............ 1 1.1 At a Glance ........................................................
TANDBERG 7000 MXP xii 3.11.5 Dual Stream (DuoVideo TF / H.239) ............................................................................ 80 3.11.6 Take New Snapshot....................................................................................
User Manual xiii 5.3.7 PIP Placing ............................................................................................................ 156 5.3.8 Presentati on Rate ..............................................................................
TANDBERG 7000 MXP xiv Appendix 1: Technica l Specifications ...................................................................................... 260 Appendix 2: Bandwidth Informat ion for TANDBER G Endpoi nts.........................................
1 Introduction The TANDBERG 7000 MXP provide s hi gh-end performance features, large monitors and precision audio. This creat es a collaborative meeting environment for medium to large-size d meeting rooms.
TANDBERG 7000 MXP 2 The system can be configured to act automatic or to give the user a choice of what to do every time the user presses a number key on the rem ote control, when in a call. Audio Quality High-performance audio provides a ri cher, more co mplete visual communication experie nce.
Introduction 3 Dialing to systems by numbers or URI, e.g. user@co mpany.com . NEW Highest level of embedded encryption as well as IEEE 802.1x and H.235 authentication for security MultiSite* The optional embedded MultiSite TF functionality can connect up to 6 video site s and 5 audio sites.
TANDBERG 7000 MXP 4 Enhanced language suppo rt with Asian a nd non-Latin character text input in the menu for local language system nam es Simplified on-screen menu, Kiosk Mode, for special pu rposes The remote control has a simplified look and feel, an auto system wake -up when picked up, and large, easy-to-read keys.
Introduction 5 1.1 At a Glance WAVE II Camera The main camera is mounted on top of the pro du ct. The main cam era includes a high quality color camera with a fast pan/tilt/zoom/focus actio n. The main cam era is controlled by the system’s infrared remote control and operates pan/tilt, focus and zoom.
TANDBERG 7000 MXP 6 Monitors The main monitor displays the far-end and nea r-end videoconferencing sites in addition to the menus and video from con necte d video sources. The secon d monitor displays selfview, Snapshots and Duo Video. Codec The codec is the heart of the system .
Introduction 7 Microphone The high quality table microphone is de sign ed to be placed on a t able during a videoconference. Up to three microphone s can be conn ected. The ideal location for the microphone is on a flat surface at least 2m (6.5 ft) from the front of the system.
TANDBERG 7000 MXP 8 TANDBERG Tracker The tracker is a small infrared rem ote control device made to steer the camera to any desired location within the room. Typically, several trackers would b e use d with each system. Each tracker has t wo buttons: One Single person button to point the camera at a specific pe rson/location.
Introduction 9 1.2 Menu Structure The Menu is available for all users a nd contains all the functionality of the system. The Cont rol Panel contains all the settings of the system. Makin g chang es to the settings will change the behavior of the system.
TANDBERG 7000 MXP 10 Note that the system features and menu se ttings may vary dependi ng on network selection and software package..
2 Inst allation Precautions: Never install communicati on wiring during a lightnin g storm. Never install jac ks f o r communication c ables in wet locatio ns unless the ja ck is specifically designed for wet locations.
TANDBERG 7000 MXP 12 2.1 Unpacking and Mounting 1 Unpacking The TANDBERG 7000 MXP is delivere d in one transport ca se with all components insid e as shown in figure 1: Figure 1 Foot Column Monitor Frame with built-in LCD monitors Monitor Rear Cover W.
Installation 13 The bolts on the bottom of the monitor frame (fr ont) shall go through the top plate of the base. Secure the monitor frame to the base wi th 2 hexagon al-shaped screws as shown in figure 4, and with 2 nuts inside the front panel of the base as shown in figure 5.
TANDBERG 7000 MXP 14 Figure 6 Figure 7.
Installation 15 2.2 Connecting Cables 1. Power cable Connect the system power cabl e to the correct co untry variant of the power cable. Connect this cable to an electrical di strib ution socket. 2. Microphone cable Connect the microphone cables to the microphone s.
TANDBERG 7000 MXP 16 2.3 Monitor Configuration Power on Switch the system on by connecti ng the power cable to an electri cal distribution socket. After the system has performed a self-test ro utin e, the Menu will be displayed on the monitor.
Installation 17 2.4 System Configuration The system must be configure d for each insta llation. Configuration settings can be made via the system menu. If an external IMUX or non-standar d network is being used it may be necessary to configure any associated external equi pment.
TANDBERG 7000 MXP 18 5. Screen Settings When using wide scree n (16:9) mo nitors, set TV Monitor Format to Wide (16:9) . TANDBERG also recommends setting Picture Layout to Picture outside Picture when using 16:9 monitors. Picture outside Pictur e provides a displ ay layout optimized for wide screen monitors.
Installation 19 4. Network Profiles Please refer to Network Profiles for details 5. Data Port Please refer to Data Port for details 6. Save changes Remember to save any changes made in the menu b y selecting the Save button on the Menu line and pressing OK.
3 General Use Wake up the sy stem When the system is not in use, it is in st andby mode and the screens are black. Wa ke up the system by picking up the remote control. An incomi ng call or pressi ng any key o n the remote control will also wake up the system.
Administrator Settings 21 3.1 The Welcome Screen When the system is switched on, the welcome scre en will be displayed. The welcome screen presents the menu and displays your main cam era image in the background (display main camera is the default setting).
TANDBERG 7000 MXP 22 3.2 Using the Remote Control The system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arro w keys a nd press OK to navigate through the menus. The system’s most commonly used functions are al so accessible directly from the rem ote control.
Administrator Settings 23 Press Selfview again to turn selfview off, see Selfview . 13. Use the Phone Book to store and recall video contacts for easy placement of calls, see Phone Book . 14. Use the red End Call key to end the current call. Pressing this key when not in a call will place the system in Standby mode, see End Call and Standby .
TANDBERG 7000 MXP 24 The remote control (TRC 4)**: 1. Change video source. If possible, you will start open a Dual Stream. Press the video source button again to stop the dual stream.
Administrator Settings 25 presentation source. If the Presentation key is held down for 1 second then the Presentation video sources menu will appear, see Presentation Key . 12. Press OK/Menu to show the menu and to select menu items, see Navigation .
TANDBERG 7000 MXP 26 3.2.1 Navigation Arrow keys and OK Navigate in the menu with the arrow key s on the remo te control. The orange selector on screen show s the selected item. Press OK to select. Cancel key In the Menu, pressing Cancel (X) w ill hide the menu.
Administrator Settings 27 3.2.2 Selfview The term “Selfview” means the outgoing image. In a normal call using the main camera, this is the image of you. The Selfview button toggles the images between Far End, Selfview and Dual Video (if any). How to use Selfview : 1.
TANDBERG 7000 MXP 28 Example: You are using the system as a PC and get an incom ing call. When the setting “Use Screen as Local PC monitor” i s On, you will keep your PC image displayed locally and the incoming call pops up in a PIP or as sm aller images in a 1+3 layout, depending on your system.
Administrator Settings 29 3.2.3 Picture Layout The layout of the screen can either be shown a s Pi cture in Picture (PIP) or Picture outsid e Picture (POP) when displaying more than one video imag e. The beh avior of the Layout button is dependent on the Picture Layout setting in Scre en Settings .
TANDBERG 7000 MXP 30 3.2.4 Mic Off To mute the microphone during a call, press the Mic off button. An on-scree n in dicator appears in the upper right corner when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash.
Administrator Settings 31 3.2.5 Volume + and - Press the Volume key to adjust the volume leve l of the codec only (not the monitor). An on- screen indicator will sh ow the current level.
TANDBERG 7000 MXP 32 3.2.6 Number and Letter keys Pressing a number key when outsi de a call will bring up the call m enu. Wh en in a call, the number keys are used for Camera Presets. Press a n umber and go to the corresponding Camera Preset (see Camera Presets ).
Administrator Settings 33 3.2.7 Touch Tones To activate dialing touch tones during a call, press the Touch tone s butt on. Oth erwise the number keys will work as configured in the Num ber Key Mode, see Control Panel – Menu Settings – Number Key Mode.
TANDBERG 7000 MXP 34 3.2.8 Presets and Extension Numbers When pressing a number key on the rem ote control, while in a call, the user can decide what shall happen.
Administrator Settings 35 3.3 On-screen Indicators The system has a number of icons signaling diffe rent settings: Microphone Off This indicator is shown when the microphone is turned off. Press the Mic off button again to turn the microphone back on, see Mic Off for details.
TANDBERG 7000 MXP 36 Telephone This indicates that there is a telephone p articipant in the conference. The displayed number indicate s ho w many telephone participa nts there are in the conference. Duo Video / H.239 This indicates that there is a Dual Vide o Stream sent from you (near end ).
Administrator Settings 37 3.4 Using the Menu Menu outside a call Menu when in a call. Press the Menu button on the remote co ntrol to displ ay the menu.
TANDBERG 7000 MXP 38 The menu contains the following items: Make a Call / Add Another Call Standby / End Call Camera Control Presentation Conference Service s Control Panel Close See Menu Structure for a full overview of the menu.
Administrator Settings 39 3.5 Make a Call It is easy to make a call: 1. Press the green Call button on remote control an d Dial number 2. Press the green Call button again to initiate the call Display the call menu by either: 1. Select Make a Call from the menu, or 2.
TANDBERG 7000 MXP 40 3.5.1 Place a Call The TANDBERG system can make both Video calls and Telephone calls . A Call Type selector button is placed to the right of the number entry field. The button sho ws if it is a video call (default) or a telephone call .
Administrator Settings 41 Place the call by either: 1. Use the arrow button on the remote co ntrol to select the Place Call icon an d press OK, or 2. Press the green call button on the remot e control.
TANDBERG 7000 MXP 42 3.5.2 Add Call (Optional feature) Conference systems with b uilt-in MultiSite can handle up to 6 video calls and 5 tel epho ne calls simultaneously. It is possible to both set up a conference with many participants and also ad d participants durin g a conference.
Administrator Settings 43 3.5.3 Call Settings The Call Settings specifies the quality of the ca ll. Each call will be set up with the default Call Settings if the settings are not altered. Normally it is not necessary for the user to alter the settings.
TANDBERG 7000 MXP 44 3.5.4 SIP Services SIP enables you to use the features Add Call and Transfer even if your system doe sn’t have multipoint capabilities. To get t he SIP Services available, you hav e to make a call using SIP as your Net. (See Call Settings) 3.
Administrator Settings 45 3.5.5 Streaming Streaming lets you broadcast your meeting to particip ants on the web. The web participant s can listen to the meeting, see snapshots, but not parti cipate themselves. Snapshot s of current stream (if MultiSite), selfview, far end and DuoVideo streams are accessible via http.
TANDBERG 7000 MXP 46 Streaming Source* Auto: Enables streaming o f both local a nd far end video. Selection of which site to be streame d is done using voice switching (the site that spe aks is st reamed). Local: Only the local video will be streamed.
Administrator Settings 47 3.5.6 Dialing In From Outside the Enterprise Dialing in Without Being Registered to a TANDBE RG Gatekeeper The feature enhancement enables diali ng th rough a TANDBERG Gateke epe r without being registered to it. This makes it easy to call in from a video system outside the enterprise.
TANDBERG 7000 MXP 48 3.6 Answer an incoming call How to answer an incoming call: To accept an incoming call, press the OK button or the green Call b utton on the remote control. How to reject an incoming call: To reject an incoming call, select the Rej ect icon and pre ss the OK button, or press the End Call button on the remote control.
Administrator Settings 49 3.7 End Call How to end a call: Press the red End Call button on the remote control, or Press the Menu button on the remote control to displ ay the menu and select End Call.
TANDBERG 7000 MXP 50 3.8 Standby The system will automatically go to Standby mode when it is not in use. In standby mode, the screen(s) are black. It is however st ill possible to receive incoming calls.
Administrator Settings 51 3.8.1 Delay Standby for 1 hour Delay Standby for 1 hour postpones the system fro m enterin g standby mode for 1 hour. This function is useful when using the monitors for a local presentat ion to preven t the system from automatically blanking the monitors.
TANDBERG 7000 MXP 52 3.8.2 Delay Standby for 3 hours Delay Standby for 3 hours postpones the automatic standby mode for 3 hours. This function is useful when using the monitors for a local presentat ion to preven t the system from automatically blanking the monitors.
Administrator Settings 53 3.8.3 Do Not Disturb To prevent the system from accepting any incomi ng calls, activate the Do Not Disturb function. The caller will hear a bu sy tone when calling t he system. The monitor will be black when Do Not Disturb is active, see figure below.
TANDBERG 7000 MXP 54 3.9 Phone Book The Phone Book is available via the Phone Book bu tton on the remote cont rol or from the Make a Call menu. Using the Phone Book is time saving and prevent s the user from inadvertently calling the wrong number. The contacts are sorte d alphabetically .
Administrator Settings 55 The following information is available from the P hone Bo ok: Placed Calls Missed Calls Received Calls My Contacts Corporate Contacts / Global Contacts.
TANDBERG 7000 MXP 56 3.9.1 Call Log The Call Log lists Placed Calls, Missed Call s and Re ceived Calls. That allows the user to see which calls that are made in the past. The lists contain a maximum of 30 numbers and the numbers are stored in these lists until the system is restarted.
Administrator Settings 57 3.9.2 My Contacts My Contacts are the locally stored contacts on t he system. This means that it is possible to add new contacts and edit or del ete existing contact s. My Contacts can store up to 200 contacts. How to make a call using My Contacts: 1.
TANDBERG 7000 MXP 58 The following functions are av ailable from My Contacts: Call Now New Contact New MultiSite Contact Edit Contact Delete Contact Close.
Administrator Settings 59 3.9.2.1 Add New Contact The New Contact function is availabl e from My Conta cts . Add a new contact to My Contacts by: 1. Select the New Contacts button to open the New Contacts dialog b ox. 2. Enter Name by using the letter keys on the remote control.
TANDBERG 7000 MXP 60 3.9.2.2 New MultiSite Contact (Optional feature*) The New MultiSite Contact function is av ailable from My Contacts . It is possible to pre-define the participa nts of a conference me eting as a MultiSite Contact.
Administrator Settings 61 Bandwidth for a MultiSite Contact call When calling a MultiSite Contact, the system will tr y to call the participants with their specified bandwidths. If the total bandwidth exceeds the sy stem's maximum bandwidth the system will downspeed and distribute the av ailable bandwidth equally among all the partici pants.
TANDBERG 7000 MXP 62 3.9.2.3 Edit Contact The Edit Contact function is available from My Contacts . How to edit a contact in the Local Phone Book: 1. Select the contact that is to be edited. 2. Press the left arrow on the remote contro l, followed by the down arrow until the Edit Contact ic on is selected .
Administrator Settings 63 3.9.2.4 Delete Contact The Delete Contact function is available from My Contacts . How to delete a contact: 1. Select the contact that is to be deleted. 2. Press the left arrow on the remote control, followed by the down arrow u ntil the Delete Contact icon is selected.
TANDBERG 7000 MXP 64 3.9.3 Corporate Contacts / Global Contacts When selecting Phone Bo ok the ph one book ope ns showing the Gl obal Contacts* or the Corporate Directory** below the folders Placed Calls, Missed Calls, Received Calls and My Contacts. These contacts cannot be change d loca lly by the system, only from the management system.
Administrator Settings 65 3.9.3.1 Up one Level Global Contacts can be arranged in a tre e stru ct ure with several sub folders. Use the Up one Level button to navigate up in the tree structure. When a search in the Global Phone Book is m ade by using the Search fun ctio n, only conta cts matching the search text are displayed.
TANDBERG 7000 MXP 66 3.9.3.2 Search The phone book can cont ain an unlimited amount of global conta c ts. Usin g search makes it easier to find the wanted contact. How to search in the Global Phone Book: 1. Select the Search icon. 2. Enter search text in the dialogue box that appears and press the OK button on the remote control.
Administrator Settings 67 3.9.3.3 Copy Contact to My Contacts The Copy Contact to My Contacts function is available from the Placed Call s, Missed Calls, Received Calls and Gl obal Contacts folders, see Phone Book for details. It may be wise to copy contacts t hat are often used to My Contacts.
TANDBERG 7000 MXP 68 3.10 Camera Control There are several ways to control the camera: Control the camera directly with the arrow keys when the menu is closed or use the Move Camera function in the menu to cont rol both the near end and far end camera, see Move Camera and Far End Cont rol for details.
Administrator Settings 69 3.10.1 Move Camera It is possible to move the camera with the remote cont rol or via the menu. Moving the camera directly with the remote control When the menu is hidden, the arrow key s will work on the camera. If the menu is displayed, press the Cancel button on the remote control to hide it.
TANDBERG 7000 MXP 70 3.10.2 Far End Control Far End Control allows you to control yo ur conference partner’s ca mera. An exa mple of when this feature could be especially helpful is if it is not possible to see wh at a partici pant at the far end is writing on their white board.
Administrator Settings 71 3.10.3 Camera Presets Use camera presets to easily vary between predef ined near end ca mera a ngles. This is useful when pictures from many different camera an gles have to be sent to the far end. E.g. in a meeting there is a white board, a PC and a sma ll meeting table.
TANDBERG 7000 MXP 72 3.10.4 TANDBERG Tracker How to save presets for the TANDBE RG Tra cker: 1. Select which camera prese t is to be use d on the TANDBERG Tracker. 2. Move the camera to the desired position to store on the tracke r. 3. Select Move Camera - Save New Preset in the menu.
Administrator Settings 73 3.10.5 Picture Control Focus, Brightness and Whi te balance are set for auto focus, auto br ightne ss a nd auto white balance by default. If you need to set focus, bri ghtness and white balance ma nually, go to Picture Control in the Camera Control menu.
TANDBERG 7000 MXP 74 3.10.6 Camera Tracking Through Camera T ra cking and the use of two or three microph ones, the camera can automatically position itself on t he current speaker. Before usi ng camera tracking, the camera positions used must be stored at Pre set 7 (Mic1) , Preset 8 (Mic2) and/or Pre set 9 (Mic3).
Administrator Settings 75 3.11 Presentation The Presentation Functionality in the system enabl es you to show other available video sources in addition to your Main Camera. This is perfe ct for meetings where you would like to sh ow a PowerPoint presentation, for example.
TANDBERG 7000 MXP 76 3.11.1 Presentation Key The quickest way to show a pre sentatio n is to use th e presentation key on the remote control. The presentation key is used to start and stop a presentation. The presentation key will display PC (default*).
Administrator Settings 77 3.11.2 Presentation Menu The Presentation menu offers you all available video sou rces; Main Camera, PC, Document Camera, VCR, AUX and VNC. All these sources can be used a s Main Video S tream or Dual Video Stream (Duo Video / H.
TANDBERG 7000 MXP 78 3.11.3 PC Presenter (DVI/VGA Input) (Optional feature - not available on all system s) Users often have their present ations on a laptop that is brought into the meeting room. Remember to connect your PC to the codec befo re you press the Presentation button.
Administrator Settings 79 3.11.4 PC Soft Presenter and VNC (Optional feature) PC SoftPresenter is used to display PC image s on yo ur system without usi ng a VGA cable (PC Presenter). The system and your PC must be connect ed to the same LAN. In addition, VNC (Virtual Network Computing) server software mu st be installed on the PC.
TANDBERG 7000 MXP 80 3.11.5 Dual Stream (DuoVideo TF /H.239) (Optional feature - not available on all system s) With Dual Stream you have the opportunity to show two different live video stre ams simultaneously, main video and one a ddi tional source.
Administrator Settings 81 3.11.6 Take New Snapshot The system can take a snapshot of your live vi deo. Snapshot is han dy when you are in a call with a system that does not support Dual Stream. Use Snapshot to show a snap shot of your presentation and continue the meeting with main camera.
TANDBERG 7000 MXP 82 3.11.7 Display Snapshot The system stores the last sent or re ceived S napshot. The snapsho t is deleted automatically after the call. How to display snapshots: 1. To view a stored snapshot, first choose the Snapshot header. 2. Select Display Snapshot in the Presenta tion menu.
Administrator Settings 83 3.12 Conference Services A Multipoint Control Unit (MCU) enables severa l sites to participate in the same conferen ce. During an MCU confe ren ce, the status line will provide information about the conferen ce.
TANDBERG 7000 MXP 84 Example of MultiSite for mid- to low end systems. Note that t he illustrations may differ from the actual product. Using the system’s internal MCU, MultiSite TF * Most TANDBERG MXP systems have an optional b u ilt-in MCU, wh ich is called MultiSite*.
Administrator Settings 85 Disconnect Participant Terminate Meeting Using an external MCU with limited Chair Control Support y ou may hav e the following services With an external MCU that does not support H.
TANDBERG 7000 MXP 86 3.12.1 Request Floor and Release Floor When requesting floor, your video will be broad casted in full screen to all other participants in the conference. Request Floo r is u seful when you want to speak or display somethi ng in front of all participants.
Administrator Settings 87 3.12.2 Conference Layout (Only supported by TANDBERG MultiSite*) With a TANDBERG MultiSite you can choose between the layouts: Auto Split, 4 Split, 5+1 Split and Voice Switched view. Auto Split displays all pa rticipants on the screen simultaneously.
TANDBERG 7000 MXP 88 3.12.3 Terminal Names Choose Terminal Names to see a list of the parti ci pants of the MultiSite c onference. Press Cancel to go back.
Administrator Settings 89 3.12.4 Chair Control (Not supported by TANDBERG MCU o r MultiSite) As chairman, you have access to more MultiSite Services. Select Chair Co ntrol to assume the role of chairman of the conferen ce. Sele ct Release Chair to end the role as chairman.
TANDBERG 7000 MXP 90 3.12.5 Assign Floor and Release Floor from Participant Assign Floor allows the chairman to sel ect whi ch of the conference participants are to be broadcasted to all other participants.
Administrator Settings 91 3.12.6 View Site and End View (Not supported by TANDBERG MCU o r MultiSite) View Site allows you to view any participant in the conference regardless of wh o has the floo r and chair.
TANDBERG 7000 MXP 92 3.12.7 Disconnect Participant Disconnect Participant allows the chai rman to di sconnect any participant in the conference. In a multipoint call, this is equivalent to disc onnecting a participant from the end call menu.
Administrator Settings 93 3.12.8 Terminate Meeting Terminate Meeting allows the chai rman to terminat e the conference altogethe r. In a MultiSite call, this is equivalent to pressing End All Call s from the end call menu.
TANDBERG 7000 MXP 94 3.12.9 More about MultiSite (embedded MCU) (Optional Feature*) Calling in to a MultiSite Any system can be part of a MultiS ite conference by calling in to a MultiSite. The dial-in numbers to the MultiSite depends of t he network that is used.
Administrator Settings 95 MultiSite cascading By connecting MultiSite systems together, it is possib le to connect even more sites in a cascaded MultiSite (see example below). All connection s can u se any combination of ISDN/IP. The host can connect up to 5 other video system s with Mult iSite functionality.
TANDBERG 7000 MXP 96 3.12.10 Text Chat While in an ISDN or IP call to another system suppo rting Text Chat (T.140), select Text Chat the Services Menu. Enter text in the displayed window. How to use Text Chat: 1. Choose Text Chat from the Servic es Menu to open the Text Chat window.
Administrator Settings 97 4 Control Panel The Control Panel contains the follo wing features: User Guide Diagnostics Audio Demo Restart Settings* Settings: General Call Qua.
TANDBERG 7000 MXP 98 4.1 User Guide The on screen user guide take s you through a quick step-by-step introduction to the video system. It gives the user basic skills in how to use the system.
Administrator Settings 99 4.2 Diagnostics Diagnostics allows testing of individual syste m components a nd displays the current system settings. Diagnostics contain: System Information Channel.
TANDBERG 7000 MXP 100 4.2.1 System Information Select System Information to view system numbers , line status, soft ware ve rsion, hardware serial number and other useful information. Press arro w key up and down to scroll in the System Information list.
Administrator Settings 101 4.2.2 Channel Status Comprehensi ve informatio n about the call progre ss is available through the Channel Status window. This window indicates the vario us stages each B-channel goes through whil st establishing a connectio n.
TANDBERG 7000 MXP 102 PRI Yellow Alarm Yellow alarm or Remote Alarm Indicator (RAI) mean s that the system is receiving framing info, but in this framing info the other side tells t he system that it is not reading the sy stem’s transmitted framing info.
Administrator Settings 103 4.2.3 Call Status Comprehensive informatio n about the call is availabl e through the Call Status window. The m enu has two columns, one for transmitted an d one fo r received audio/vi deo/data information.
TANDBERG 7000 MXP 104 4.2.4 System Selftest The system performs a che ck to determine internal hardware integrity. System Selftest is useful when you want to check if your network connection is active.
Administrator Settings 105 4.2.5 View Settings This window displ ays all th e system settings. Us e the arrow key on the remote control to scroll through the list.
TANDBERG 7000 MXP 106 Document Camera VCR AUX VNC Split Screen Default Call Settings Call Type Network Bandwidth Restrict (5 6 k) Auto H320 Bandwidth Auto H323 Bandwidth SIP Audio Settings Inputs Mic1.
Administrator Settings 107 Brightness Video Name Main Cam AUX Doc Cam VCR PC VGA VNC Network Ty pe ISDN-BRIPRILeased E1T1Exnternal H331 ISDN Switch Type ETSI (Euro ISDN) Line1 Setup On Number1 Number2.
TANDBERG 7000 MXP 108 Gateway Ethernet Speed DNS Settings H.323 Settings E.164 Alias Use Gatekeeper Gatekeeper IP H.323 Prefix Advanced H.323 Settings RSVP NAT NAT Address QoS IP Precedence Audio Video Data Signaling IP Type of Service (TOS) Diffserv Audio Video Data Signaling IEEE802.
Administrator Settings 109 Data Port 1 Baud rate Parity Databits Stopbits Mode Data Port 2 Baud rate Parity Databits Stopbits Mode * The Settings available will vary within the MXP system r ange depending on system and what software options installed.
TANDBERG 7000 MXP 110 4.2.6 IP Address Conflict Check The system will give a warning if there is an IP conflict. The user may initiate this check by selecting IP Address Conflict Che c k.
Administrator Settings 111 4.2.7 Warnings Any warnings registered by the system will be displayed in the Warnings me nu. Open a warning in the list to get more information about the warning.
TANDBERG 7000 MXP 112 There is something wrong with the Leased E1/T1 line (Yellow alarm). Please check your network connection. (1 93) H323 gatekeeper warnings Could not register to the gatekeeper. The gatekeeper rejected to register the syste m.
Administrator Settings 113 4.3 Audio Demo TANDBERG systems are desi gne d to improve audio quality during a video con f eren ce – as if the person is in the same room! Demonstrate the high quali ty Audio of your system by pressing the Audio De mo button at the bottom of the Control Panel menu.
TANDBERG 7000 MXP 114 4.4 Restart Restart the system by pressing the Restart butt on. You are prom p ted with a dialog box saying: Do you want to restart the system? Press OK to restart, press Cancel (X) to abort. You will also find the Restart button at the bottom of the Control Panel menu.
Administrator Settings 115 5 System Settings The Control Panel contains all the settings of the syst em. Making changes to the settings will change the behavior of the system.
TANDBERG 7000 MXP 116 5.1 General Settings When installing the system, go through the Gene ral Settings menu to ensure that you have the right settings for your syste m , see Syste m Configuration.
Administrator Settings 117 5.1.1 Language The system supports 16 dif f erent lang uages for its on-screen menu s; English, G erma n, Fren ch, Norwegian, Swedish, Italian, Spanish, P ortuguese, Russian, Finnish, Chinese Simplified, Chinese Traditional, Japanese, Korean, Thai and Arabic.
TANDBERG 7000 MXP 118 5.1.2 System Name System Name identifies the sy stem: On the welcome page. During an MCU conferen ce call. When using the Web-interf ace. When the codec is acting as an SNMP Agent. Towards a DHCP serve r. H323 ID.
Administrator Settings 119 5.1.3 International Name If the System Name contains Asian and non-Latin cha racte r text input, the International Name using Latin characters only , must be sp ecified as well. This is in order to make other s ystems understand the system na me.
TANDBERG 7000 MXP 120 5.1.4 Auto Answer The auto answer setting decides whether an incomin g call is p ut through automatically or manually. On The system will automatically answer al l incoming cal ls. On+Mic Off The system will automatically answer all incomin g cal ls and switch the microphone off when the call is connect ed.
Administrator Settings 121 5.1.5 Phone Book Settings Corporate Directory On The Corporate Dire cto ry is available in the menu. Off The Corporate Dire cto ry is hidden from the menu and is unavail able for users. IP address Enter the IP address of the management system that provides the Phone Boo k.
TANDBERG 7000 MXP 122 5.1.6 External Services Settings External Services On When set to On External Services are available. Off When set to Off External Services are unavailable. IP address Enter the IP address of the service provider for Extern al Service s.
Administrator Settings 123 5.1.7 Permissions Permissions contains settings for in coming MC U Calls, inco ming telephone Calls, Far End Control, Remote Software Upgrade and Fallba ck to Telephony. Access Code An access code will help you control the use of the system.
TANDBERG 7000 MXP 124 Far End Camera Control On The far end will be able to: • Control your camera • Select your video sources • Activate your camera presets • Request snapshots Off The far end can access none of the four features abo ve on the local system.
Administrator Settings 125 5.1.8 Screen Settings Auto Layout On If Auto Layout is On the system will change layouts automatically depen ding on t he number of participants in a call and if you have a dual video strea m or not. Please refer to Layout for more information.
TANDBERG 7000 MXP 126 recommended. You will get optimiz ed picture layouts for wide sc reen by pressi ng the Layout button on the remote. Picture in Picture (PIP) Pressing the Layout button on the remote will result in an extra picture in smaller view (Picture in Picture).
Administrator Settings 127 Example of 1+2 Picture outside Picture (wide screen). Example of 1+3 Picture outside Picture (wide screen). Note that if both TV monitor format and VGA format is set to Normal, the system will skip the 1+3 layout, which is not beneficial for 4:3 monitors.
TANDBERG 7000 MXP 128 wide screen (16:9) monitor or projecto r. T he VGA and DVI output will then be optimized fo r Wide Screen VGA and High Definition (HD) display. Normal Output format is optimized fo r Normal VGA monitors (4:3) Wide Output format is optimized for Wide VGA monitors (16:9) Wide screen VGA or TV monitor in Normal (stretched) mode.
Administrator Settings 129 Auto VGA output format will be optimized dependant of the video source format, refresh and of the EDID information avai lable.
TANDBERG 7000 MXP 130 PC Presentation shown in Wide (stretched) mode..
Administrator Settings 131 5.1.9 Software Options The system requires a valid option key to activa te MultiSite and/or Presenter functionality. In order to activate additional band width, you need to enter a bandwidth key. A restart of the system is required after entering a new option a nd/or bandwi dth keys.
TANDBERG 7000 MXP 132 5.1.10 Date and Time Settings NTP IP This is the NTP time server address from whi c h the system can get updated time information. See IP Services for more details. Auto The NTP IP will be provided by the DHCP server. Manual The NTP IP address is set manually.
Administrator Settings 133 5.2 Menu Settings Menu Settings contain the settings: Input Editor Language Menu Timeout In Call Menu on TV Menu on PC Balloon Help Number Key Mode .
TANDBERG 7000 MXP 134 5.2.1 Input Editor Language When the Input Editor Language is set to Chinese, Korean or Jap anese the user will be able to enter Chinese / Korean / Japanese characters into an input field like the System Name or Phone Book, using the remote control.
Administrator Settings 135 5.2.2 Menu Timeout in Call The Menu appears on the bottom line of the screen. Set Menu Ti meout in Call to On if you want the menu to time out automatically when you are in a call. On The menus will time out automatically after 15 seconds if there is no activity on the remote control.
TANDBERG 7000 MXP 136 5.2.3 Menu on TV The Menu on TV setting decides if the menu shall be displayed o n the TV screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on PC is On a nd vice versa. On The menu is available on the TV screen .
Administrator Settings 137 5.2.4 Menu on PC The Menu on PC setting decides if the menu shall be displayed o n the PC (VGA screen) screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on P C is On and vice versa. On The menu is available on the PC screen.
TANDBERG 7000 MXP 138 5.2.5 Balloon Help It is possible to enable / disable the ballo on help window. On Choose On if you want help text windows to appear.
Administrator Settings 139 5.2.6 Number Key Mode When pressing a number key on the rem ote control, while in a call, the user can decide what shall happen.
TANDBERG 7000 MXP 140 The Number Key Mode is set to Manual Settings for Remote Co n trol Nu mber Keys while in a call: Add Call While in a call, the Call Menu will automatically app ea r when a number key is pressed on the remote control. This will enable the user to add another call.
Administrator Settings 141 If you have no stored presets on y our system, you are likely not to use presets. Therefore the presets option is not present in the dialog box. Press arrow key to navigate in the list. Press OK on the remote control to select the desired ent ry.
TANDBERG 7000 MXP 142 5.2.7 Administrator Password It is recommended to put an Administrator Passw ord on the system. The Administrator Password can be maximum 5 digits long. The Administrator Password dialog box will pop up when you choose Settings from the Cont rol Panel.
Administrator Settings 143 5.2.8 Kiosk Mode Settings Kiosk Mode In Kiosk Mod e t he system is set to a sim plified st ate where it can be contro lled wit h just the four arrow keys and OK.
TANDBERG 7000 MXP 144 If Language Menu is enabled you will first see the lan guag e selection menu. Select languag e and the Welcome Menu will be displayed wit h your desired language.
Administrator Settings 145 Kiosk Mode - Auto Dial* On The system will automatic ally dial to t he first contact in the Phone Book when he handset is lifted. If this contact is busy, t he system will call the seco nd number in the Phone Book and so on.
TANDBERG 7000 MXP 146 5.2.9 Startup Welcome Menu The Welcome Menu contains the Menu, System Stat us, your System Nam e and dial in numbers. On The Welcome Menu is sh own when the system wakes up from st andby mode. Off The Welcome Menu is not shown when the system wakes up from standby mode.
Administrator Settings 147 Off Welcome text is not displayed on the wel come m enu. Welcome Text You can change the welcom e text to any text you like, instead of the default text. Remember t hat Display Welcome Text must be On to be able to edit the welcome text.
TANDBERG 7000 MXP 148 5.2.10 Icons The following indicator ico ns may be set to on or off: Mic Off Volume Off On Air Encryption Bad Network Telephone DuoVideo/H.
Administrator Settings 149 5.3 Presentation Settings Presentation Settings contain: Presentation Start H.239 Startup Video Source Presentation Source Snapshot Source Auto-Displ.
TANDBERG 7000 MXP 150 5.3.1 Presentation Start If your system has Dual Stream capa bil ities, y ou can show two video streams at the same tim e (see also Dual Stream ). Presentation St art is Auto by default. This means that you will start Dual Stream (a second video st ream ) automatically when starting a p re sentatio n.
Administrator Settings 151 5.3.2 H.239 H.239 supports transmission of two video st ream s. It combi nes elements of Duo Video and People+Content. If H.239 is disabled you will still be able to start TANDBERG Dual Video Stream* Enabled Enables H.239 Disabled Disables H.
TANDBERG 7000 MXP 152 5.3.3 Startup Video Source The Startup Video Source is the video source on display w hen the system wakes up from standby mode. If you use Main Camera as star t up source, the system will start with Main Camera every time the system wakes up from stan db y, regardl ess of what the previous user was using.
Administrator Settings 153 5.3.4 Presentation Source The Presentation Source is connected to the Pr esentation button on the remote. Pressin g the Presentation button will put the Pr esentation Source on display. Presentation Source is PC by default*.
TANDBERG 7000 MXP 154 5.3.5 Snapshot Source When you take a Snapshot, you get a snapshot of the Snapshot Source. Current is the default Snapshot Source. This means that you take a sn apshot of the video source that is cu rrently active. You can change the Snapshot Source to any vi deo source.
Administrator Settings 155 5.3.6 Auto-Display Snapshot Select Auto to automatically display a received snapshot. Turn Auto-Di spl ay Snapshot Manu al if you wish not to have them displayed on the sc reen when they are sent or received. The snapshots will be sent and received, but not di splayed.
TANDBERG 7000 MXP 156 5.3.7 PIP Placing PIP Placing lets you decide where the PIP shall appear. You can of course m ove the PIP with the Layout button on the remote anytime. Top Right PIP is placed in the Top Right corner. Bottom Right PIP is placed in the Bottom Right corner.
Administrator Settings 157 5.3.8 Presentation Rate When setting up a call with H.323 the ba ndwidth can be controlle d by the user. The Presentation Rate is expressed in p ercent of the Call Rate and shall reflect the H.323 Presentation Rate settings of the sender.
TANDBERG 7000 MXP 158 5.3.9 VNC Settings VNC Settings is necessary when using a VNC present ation. See the chapter PC Soft Presenter and VNC for more information on how to use VNC.
Administrator Settings 159 5.4 Call Quality Call Quality contains the settings: Video Algorithm Audio Algorithm AAC-LD 128kbps Natural Video Max Upstream Rate Video Quality .
TANDBERG 7000 MXP 160 5.4.1 Video Algorithm The system will automatically select the best video algorithm b ase d on the video source and the capabilities of the remote system. Use this menu to disabl e video al gorithms in case you have interoperability issues calling other systems.
Administrator Settings 161 5.4.2 Audio Algorithm The system will automatically select the bes t audio al gorithm based on the call rate and the capabilities of the remote system. Use this menu to disable audio algorithms in case you want to remove “low quality” audio , or if you have in teroperabi lity issues calling other systems.
TANDBERG 7000 MXP 162 5.4.3 AAC-LD 128kbps (stereo audio) Specify a call rate for 128kbps AAC-LD. From this call rate and abo ve, "128kbps AAC-LD" is available. On lower call rat es "64 kbps AAC-LD" is av ailable. Stereo audio require s twi ce the bandwidth as mo no CD-qu ality audio.
Administrator Settings 163 5.4.4 Natural Video Choosing Natural Vide o will enable 60 fields* per se cond true interlaced pictu re for high m otion video. The use of Natural Video requires the H. 263+ and H.263++ video protocol s. Natu ral video will be disabled in H.
TANDBERG 7000 MXP 164 5.4.5 Max Upstream Rate (kbps) The Max Upstream Rate (kbps) defines the desi red maximum tran smitted call rat e over H.323 networks.
Administrator Settings 165 5.4.6 Video Quality The different video sources need differe nt Video Qual ity Settings. Main Camera, VCR, AUX and Split Screen have Motion as default.
TANDBERG 7000 MXP 166 Sharpness*: Improved quality of detailed images and grap hics, lower fram e rate and ideal for enhancing quality at lower bandwidths.
Administrator Settings 167 448p (576 x 448) iCIF (352 x 576 pixels), Natural Video CIF (352 x 288 pixels) QCIF (176 x 144 pixels) SQCIF (128 x 96 pixels) Native PC Resolutions: .
TANDBERG 7000 MXP 168 5.4.7 Default Call Settings Default Call Settings are connected with Call Settings in the call menu. If you leave Call Settings unchanged when making a call, the syst em will use the default Call Settings in the call. In addition to the Call Settings Call Type, Net, Bandwidth and Restrict (56k), you also find settings for H.
Administrator Settings 169 Select ISDN to ensure that the call is set up as an ISDN call. Select H.323 to ensure that the call is set up as an H.3 23 call. Select SIP to ensure that the call is set up as an SIP call. Bandwidth Bandwidth decides the qu a lit y of the video picture.
TANDBERG 7000 MXP 170 These types of calls are often referred t o as H.221 calls 2x64 calls 2x56 calls - as making 2 x 64 kbps or 2 x 56 kbps call s to the same system. Place this type of call by: Set Network to ISDN Set Bandwidth to 128 kbps A field for the 2nd number pops up in Call Settings.
Administrator Settings 171 5.5 Audio Audio contains the settings: Inputs Outputs Echo Control Stereo Settings Audio Leveling (AGC) Alert Tones and Volume Graphical View.
TANDBERG 7000 MXP 172 5.5.1 Inputs Mic 1- 3 and Audio input 4-6 By default, all inputs are enabled. Just plug in an au dio sou rce and it is active. Audio inputs that are On will automatically be mix ed. Unconnected inputs will automatic ally be muted.
Administrator Settings 173 Level Settings It is possible to adjust the audio input levels ac cording to which external audio eq uipment is connected. The on-screen audio level indicator will m a ke it easier to set the correct input level settings.
TANDBERG 7000 MXP 174 TANDBERG Audio Science m icroph one elements: Audio Technica AT-861P Z and Crown PZM- 6D Signal levels - microphone inputs Clipping level Nominal level Input menu level settings Vpp dBu dBu 0.0 dB 83.0 mVpp -28.4 dBu -46.4 dBu 1.
Administrator Settings 175 Signal levels - line level inputs Clipping level Nominal level Input menu level settings Vpp dBu dBu 0.0 dB 15.5 Vpp 17.0 dBu -1.0 dBu 1.5 dB 13.0 Vpp 15.5 dBu -2.5 dBu 3.0 dB 11.0 Vpp 14.0 dBu -4.0 dBu 4.5 dB 9.2 Vpp 12.5 dBu -5.
TANDBERG 7000 MXP 176 5.5.2 Outputs Audio out 1 - 3 Audio out 1 is intended for connection to TANDBERG Digital Natural Audio Module, television s or audio amplifiers. Audio out 2 is intended for connection to audio re co rding equipment or to a teleph one add-on hybrid.
Administrator Settings 177 Signal levels - line level outputs* Absolute max. output level Nominal level Output menu level settings Vpp dBu dBu 0.0 dB 1.2 Vpp -5.5 dBu -23.5 dBu 1.5 dB 1.4 Vpp -4.0 dBu -22.0 dBu 3.0 dB 1.6 Vpp -2.5 dBu -20.5 dBu 4.5 dB 1.
TANDBERG 7000 MXP 178 5.5.3 Echo Control Mic 1-3 and Audio 4 Each of the 3 microphone inputs a nd Au dio input 4 has a separate acoustic echo can celler. One echo canceller per input provides mo re sophisticated control than having one co mmon canceller for all microphones.
Administrator Settings 179 5.5.4 Stereo Settings Settings Output response Out 1 Mode* Stereo I/O Mode Stereo Speakers Audio out 1 Audio out 2 Audio out 3 Analog Off Off Loudspeaker mono AUX VCR Analog.
TANDBERG 7000 MXP 180 Note that if Stereo Speakers are enabled in the menu without having any stereo speakers connected to the Digital NAM, it may cause the acoust ic echo-ca nce ller to malfunction.
Administrator Settings 181 5.5.5 Audio Leveling (AGC) On Select On to allow automatic adjustments (Automatic Gain Control ) of audio leve ls. When On, the AGC maintains the audio sign al level at a fixed value by attenuating strong signals and am plifying we ak signals.
TANDBERG 7000 MXP 182 5.5.6 Alert Tones and Volume Video Call Alert Tone and Telephone Alert Tone To help distinguish between incoming video calls a nd ordinary telephone call s, it is re commended to use different ringing tones for video calls and telep hone calls.
Administrator Settings 183 5.5.7 Graphical View Graphical View The graphical view is a visual presenta tion of the audio inputs and audio o utputs. • The Inputs + Far End In are listed on the le ft, showing the name of the input sources. • The outputs + Far End Ou t are listed on the bottom, showing the name of the output sources.
TANDBERG 7000 MXP 184 5.6 Video Video contains the settings: Camera Tracking Mo de MCU Status Line Floor to Full Screen Web Snapshots MultiSite Picture Mode Video Name.
Administrator Settings 185 5.6.1 Camera Tracking Mode Slow The system waits a while before zoomi ng in on a si ngle person speaki ng. Suitable when wide-angle images are preferred over close-up images. Normal Should be used in regular meetings. Fast The system quickly zooms in on a sing le person speaking.
TANDBERG 7000 MXP 186 5.6.2 MCU Status Line On The MultiSite / MCU / DuoVideo indicat ors will be di splayed and provide information about the conference. Off The MultiSite / MCU / Duo V ideo indi cators will not be displaye d. Auto The MultiSite / MCU / DuoVideo indicat ors will be displayed for a few seconds and then timed out.
Administrator Settings 187 5.6.3 Floor to Full Screen When "Floor to Full Screen" is enable d, some one wh o requests floor will be seen by all participants as full screen.
TANDBERG 7000 MXP 188 5.6.4 Web Snapshots The system is able to generate JPE G snapshots and provide them when requested (as ‘http g et’ or via ftp). See Appendix 6 for descriptions of the possible snapshot files. On Snapshots generation is enabled.
Administrator Settings 189 5.6.5 MultiSite Picture Mode MultiSite* Picture Mode determines the default lay out of a MultiSite call. Available layouts are: Auto Split, 4 Split, 5+1 Split, and Voice Switched. You can change the layout during a call using the layout option in MultiSite Services.
TANDBERG 7000 MXP 190 Voice Switched mode.
Administrator Settings 191 5.6.6 Video Name As a default, the video inputs are given the name s Main Cam, PC, Do c Cam, VCR, AUX or VNC, dependent on what video sources ar e available on yo ur system.
TANDBERG 7000 MXP 192 5.7 Security Security contains the settings: Encryption Encryption Mode Passwords Camera Standby mode.
Administrator Settings 193 5.7.1 Encryption (Country specific) Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption (AES or DES), the call will be encrypted. If not, the call will proceed without encryption.
TANDBERG 7000 MXP 194 5.7.2 Encryption Mode Auto The system will try to use the most secure encryption - AES, dependent on the capabilities of the other si tes. For sites that do not support AES encryption, DES encryption will be tried. AES The system will try to use AES with 128 bits encryption when setting up calls.
Administrator Settings 195 5.7.3 Passwords Administrat or Password, IP Access P assword , Streaming Password, VNC Password, Access Code and Remote Software Upgrad e password ar e duplicated from their respe ctive menus. Using the Security menu g ives you a qui ck way to change all password s of the sy stem.
TANDBERG 7000 MXP 196 5.7.4 Camera Standby Mode There is a setting to the Security menu called Camera Standby mode On (default)/Off. When Camera Standby mode is On, the came ra turns away when stand by is activated. When the system is activated the camera turns b ack to norm al position.
Administrator Settings 197 5.8 Network The network menu contain: ISDN/External/Leased E1/T1 LAN Settings Network Profiles Data Port.
TANDBERG 7000 MXP 198 5.8.1 ISDN/External/Leased E1/T1 Network Typ e Before using the system it is necessary to spe cify which network to use and define its settings. ISDN- BRI If you want to use your system via IS DN-BRI, you should sel ect Network Type: ISDN-BRI and enter the ISDN BRI Settings menu to set the BRI parameters.
Administrator Settings 199 5.8.1.1 ISDN-BRI Settings To make sure your system will work properly using ISDN-BRI, make the fo llo wing settings: 1. Set ISDN switch type 2.
TANDBERG 7000 MXP 200 Advanced ISDN Settings Sub address Using a sub address ena bles you to connect up to eig ht ISDN termi nals to the same ISDN telephone number and line.
Administrator Settings 201 5.8.1.2 ISDN-PRI Settings To make sure your system will work properly using ISDN-P RI, configure the follo wing settings: 1. Set PRI switch type 2. Enter PRI line number Note that the T1 format is predefined to ESF and the line code is B8ZS.
TANDBERG 7000 MXP 202 Example: Max Channels may be used for PRIs tha t are provisioned for a lower num ber of channels. High Channel, Low Ch ann el and Search may be used for PRIs provision ed wit h specific requirements for B-chann el usage.
Administrator Settings 203 Advanced ISDN-PRI Settings NSF is a non standard facility. Your network p rov ider may require a service selection in your ISDN configuration. Enter the Serv ice code here. Valid NSF se rvice codes are from 1 to 31. Enter 0 to disable NSF service codes.
TANDBERG 7000 MXP 204 5.8.1.3 Leased E1/T1 Settings Call Control Auto When Auto is selected, the system will automatically initiate a connection as soon as it detects that the far end trie s to make a call.
Administrator Settings 205 5.8.1.4 External Network Settings Before using the system together with ex ternal network equipm ent, you must specify the network parameters on this page. The syste m ha s support for up to 2 Mbps (dependi ng on the Bandwidth key loaded) using the External Network (RS449/ V.
TANDBERG 7000 MXP 206 Network clocking The network clock setting specifies the numbe r of physical external clock si gnal s. RS449/V35 Compatible Use RS449/V35 Compatible when t he external equi pment provides two clock signals, one for tran smit and one for receive.
Administrator Settings 207 5.8.1.5 H.331 Settings On Used when broadcasting a videoco nference from one site to many others, e.g. via satellite, where there is no possibility to negotiate quality between the receivers and the originator due to one-way communication.
TANDBERG 7000 MXP 208 5.8.2 LAN Settings LAN Settings contain: IP Settings H.323 Settings SIP Settings SNMP Settings IP Services Quality of Service 802.
Administrator Settings 209 5.8.2.1 IP Settings Remember to restart the system after making cha nge s to IP Settings. This can be done by selecting the “Save and Restart” at the b ottom of the IP setting men u. Changes in IP Settings menu will not have any effect until the system is restarted.
TANDBERG 7000 MXP 210 Ethernet Speed Auto The codec will auto-dete ct t he speed/d uplex on the LAN. 10/Half The codec will conn ect to the LAN u sing 10Mbps speed/Half Duple x. 10/Full 10 Mbps speed/Full Duplex . 100/Half 100 Mbps speed/Half Duplex. 100/Full 100 Mbps speed/Full Duplex.
Administrator Settings 211 DNS Settings DNS Server 1-5 DNS Server defines the network addre sses fo r DNS serve rs. Up to 5 addresses may be specified. If the network addresses are unkno wn, please contact your administrator or Internet Service Provider.
TANDBERG 7000 MXP 212 5.8.2.2 H.323 Settings E.164 alias This is the E.164 address of the system . The E.164 addre ss is equivalent to a telephone num ber, sometimes combined with access code s. Valid characters are 0-9, * and #. Whe n using a gatekeeper, the system will send a messag e to the gatekeeper containing both the E.
Administrator Settings 213 Gatekeeper Settings Gatekeeper Discovery Auto The sy stem will automatically try to register to any available gate keeper. If a gatekeeper responds to the request sen t from the codec within 30 second s this specific gatekeeper will be use d.
TANDBERG 7000 MXP 214 Multiple H.323 Aliases is set to Off. If set to Off, the system will register a si ngle H.3 23-IDs on the Gatekee per b ased on the following priority: • H.323 ID • International Name • System Name The default setting for Multiple H.
Administrator Settings 215 CallManager Settings CallManager IP This is the CallManager IP-address that is used if you specify H.323 Call Setup: CallManager.
TANDBERG 7000 MXP 216 Advanced H.323 Settings The Advanced H.323 Settings only have an effect if t hey are supported by your IP infrastructure. NAT NAT, Network Address Translation, is used whe n a PC and a vide oconferencin g system a re connected to a router with NAT suppo rt.
Administrator Settings 217 H.323 Ports Static When selecting static H.32 3 ports for TCP connections the ports 5555 to 5574 will be used for Q.931 and H.245 respe c tively. Dy n ami c The system will allocate which ports to use when opening a TCP connection.
TANDBERG 7000 MXP 218 5.8.2.3 SIP Settings Mode On Setting the SIP mode to on will enable the system for incoming and outgoin g SIP calls. Off Setting the SIP mode to off will disable incoming and outgoing SIP calls from the system. Display Name The Display name part of the SIP Addre ss (U RI) is usually a full name or system name.
Administrator Settings 219 Server Address The Server Address is the manually con f igured a ddress for the out boun d proxy and registrar. It is possible to use a fully qualified domain name, or an IP addres s. The default port is 5060 for TCP and UDP, but another one can be provided.
TANDBERG 7000 MXP 220 RFC 2032 RTP Payload Format for H.261 Video Stre ams Draft-ietf-avt-rfc2032-bis-0 6.txt - Draft for advan ced video signaling including resolution and mpi. RFC 2190 RTP Payload Format for H.263 Video Stre ams RFC 2429 RTP Payload Format for the 1998 Versi on of ITU-T Re c.
Administrator Settings 221 5.8.2.4 SNMP Settings SNMP Settings SNMP Trap Host identifies the IP-address of the SNMP manager. SNMP (Simple Network Management Protocol, SNMP Ver 1) is used for m onitoring and co nfiguring of different entities in a network.
TANDBERG 7000 MXP 222 5.8.2.5 IP Services NTP IP This is the NTP time server address from whi c h the system can get updated time information. This is a requirement for proper o pe ratio n if H.235 authentication is implemented. The Network Time Protocol (NTP) i s used to sync hronize the time of the system to a reference time server.
Administrator Settings 223 5.8.2.6 Quality of Service QoS Type Off No QoS is used. Diffserv Diffserv QoS method is used. Please see belo w for d etails. IP Precedence IP Precedence QoS method is used. Please see below for details. IP Precedence Video Used to define which priority audio, video, dat a and signalin g should have in the network.
TANDBERG 7000 MXP 224 Auto will provide the following priority: Audio 4 Diffserv Video Used to define which priority Audio, Video, Da ta and Signaling packets sho uld h ave in an IP network.
Administrator Settings 225 5.8.2.7 IEEE 802.1x 802.1X The system may be connected to an IEEE 802.1x LAN network. Supported 8 02.1x protocols are EAP-MD5, EAP-PEAP and EAP-TTLS. The 802.1x authent ication are enabled by setting 802.1x Mode to On. On 802.
TANDBERG 7000 MXP 226 5.8.3 Network Profiles This menu consists of 7 network profiles; a prefix and a suffix can be added for each p rofile. If you add a prefix/suffix to a profile, this prefix/su ffix will automatically be add ed in front/back of the number being dialed.
Administrator Settings 227 5.8.4 Data Port The system provides up to two standard RS232 seri al ports to allow a computer to be conne ct ed for data transfer and control purposes. Note that wh en co nnecting to a PC the conne cting cable must be a straight through RS232 cabl e.
TANDBERG 7000 MXP 228 5.8.5 Restore Default Settings Restore Default Settings will restore all system setti ngs. Note that this will not affect your Call Directory information, Network Type, Li ne Setup numbers or your SPID numbers.
6 Peripheral Equipment Using the optional peripheral device s outlined in this chapter and the many others available, you will be able to build your own applications for us e with the system, thereby better integrating the system into your business environ ment.
TANDBERG 7000 MXP 230 6.1 Interfaces 6.1.1 Video 5 Video Inputs: 2 video inputs supporting S-Video throu gh Mini-DIN connectors. 2 video inputs supporting comp osite signals through RCA conn ect ors. 1 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) inpu t, analog or digital.
Peripheral Equipment 231 Levels: Composite: 1 Vpp, 75 ohm S-Video (Y/C): Y: 1 Vpp, 75 ohm C (PAL): 0.3 Vpp, 75 ohm C (NTSC): 0.28 Vpp, 75 ohm VGA formats supported on 'DVI-I o.
TANDBERG 7000 MXP 232 Supported DVI cables: TANDBERG supports DVI-D Single -Lin k , DVI- A and DVI-I Single-Link format cables. DVI-D cables transmit digital T.M.D.S. signal s, DVI-A cabl es transmit analog VGA signals a nd DVI-I cables can transmit either digital or anal og signals.
Peripheral Equipment 233 The TANDBERG 6000 MXP Profile and 3000 MXP Profile* systems are shipped with a PC cable with integrated audio : DVI-A Plug + 2*RCA Plug to VGA Plug + 3.5mm Stereo Plug, length 6m. PC cable, VGA - DVI with integrated audio Signal name CON.
TANDBERG 7000 MXP 234 RGB Return C5 6, 7, 8 RGB Coax Shield Outer Shield Ground Shell Shell Outer Shiel d Audio Left Centre Tip Audio Black Audio Right Ring Centre Audio Red Audio GND Gnd Sleeve Gnd Audio Shield PC cable, VGA - DVI with integrated audio * Applies to T3000 MXP Profile with new hardware.
Peripheral Equipment 235 VGA to DVI-A Cable Pinouts* : VGA to DVI-A cable male-male 5m black, maximum length 5m. No Item Description 1 Cable UL20276 3Coax*30#+IP*28#+5C*28#+AEB Black OD:7.0mm L-5000mm 2 Connecto r HD D 15P Male Black 3 Connecto r HD D 17P Male Black 4 Tube PE Tube Black OD:1.
TANDBERG 7000 MXP 236 6.1.2 Audio 6 Audio Inputs: 3 microphone inputs (balanced, 24V phantom powere d) via XLR co nnectors. 3 audio inputs (line level) via RCA connectors. All audio inputs are active by default. For further information, refer to chapter Audio .
Peripheral Equipment 237 Connector label Audio outputs Signal type Unbalanc ed Connecto r (codec) Female RCA/phon o, sleeve-g round, centre-signal Output impedance 680 ohm s Max output level when set to maximum output level and volume control set to max.
TANDBERG 7000 MXP 238 6.1.3 Network Ethernet: 1 x Ethernet (RJ-45 Jack) LAN interface (10/ 100 M b) up to 4 or 6 Mbps depe nding on the bandwidth option installe d. To connect the system to a LAN, use the Ether net cable provided b y TANDBERG (or a standard Ethernet cable).
Peripheral Equipment 239 The pinout of the E1/T1 interface is: PRI Pinout Crossover PRI cable Pin-1 RX+ 4 Pin-2 RX- 5 Pin-4 TX- 1 Pin-5 TX+ 2 Note! TANDBERG recomm end s always using category 5 cabling.
TANDBERG 7000 MXP 240 6.1.4 Data port The data port(s) are imple mented as Data Comm unications Equipm ent (D CE). The connector used are female 9-pin D-subs. NOTE! Data port 2 is used by both Wave II Camera and Precisi on HD Camera and has differe nt pin-out scheme for the different use.
Peripheral Equipment 241 6.2 Document Camera A document camera can be used for sho wing text, diagram s and a variety of graphical material as well as small three-dimensio nal obje cts. How to use a document camera with your system: 1. Connect the document camera to the Do c Cam input, if available, on the system.
TANDBERG 7000 MXP 242 6.3 DVD / VCR DVD/VCR Playback Mono For playback, connect a cable between Video Out on the VCR and Video In (VCR) on the system. Connect a cable between Audio Out on t he VCR a nd the Audio In (VCR) on the system. Choose VCR from the Presentation menu to activate the VCR in put .
Peripheral Equipment 243 6.4 Additional Cameras Extra fixed Cameras You can connect extra fixed camera s to your sy stem, for example, a whiteboard camera. Con nect the video output of the additional camera to one of the available Video inp uts on the system.
TANDBERG 7000 MXP 244 6.5 Additional Microphones If your environment is such that you require more than one microphone for you r room, e.g. you have a whiteboard at a distance from your table microphone, it is possible to con nect ad ditional microphones to your system.
Peripheral Equipment 245.
TANDBERG 7000 MXP 246 6.6 The TANDBERG DNAM and Speakers TANDBERG 6000 MXP Profile, T ANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro The TANDBERG Digital Natural Audio Mod.
Peripheral Equipment 247 TANDBERG 8000 MXP DNAM configuration TANDBERG 6000 MXP Profile DNAM configuration Center Speakers + In tegrated Stereo Speakers The DNAM Amplifier*: 3 x 50W continuous average Center Out put Powe r (lo ad specified by DNAM Center Speakers).
TANDBERG 7000 MXP 248 The DNAM Loudspeaker Cabinet (Center Spe aker s)*: 3-way Center Speaker system Frequency range 50Hz - 2 0kHz 2 x 130mm low- and midrange loudspeakers, 8 ohm s nominal.
Peripheral Equipment 249 TANDBERG 3000 MXP Profile: The TANDBERG Mini-DNAM*: The Mini-DNAM audio system is built on two spec iall y design ed and separate modules; the Mini- DNAM amplifier and the Mini-DNAM loudsp ea ker ca binet.
TANDBERG 7000 MXP 250 6.7 Stereo Speaker Kit Note that the following applies only for system s with a stereo S/PDIF output. The Stereo Speaker Kit provides an pair of floor-s tanding lou dsp eakers in addit ion to the built-in DNAM . Using these speakers will ena bl e stereo func tionality in your system and thereby en ha nce the sound experience.
Peripheral Equipment 251.
TANDBERG 7000 MXP 252 6.8 Telephone Add-On The system has a built in audio bri dge* that can br ing in Voice over IP (VoIP) telephony or normal telephone sites using ISDN. Note that this requires a system with mix ed audi o output (audio from local and far end ) and one audio input without integrated echo cancelli ng.
Peripheral Equipment 253 6.9 Dual Monitor Note that this requires a system with du al monitor vid eo output. TANDBERG 7000 MXP is a dual monitor system with the Dual Mo nitor option included.
TANDBERG 7000 MXP 254 6.10 XGA Monitors and Projectors (Optional) Some TANDBERG systems can be delivered with op tional single or dual TV/X GA monitors. It can also be connected to any DVI/VGA/PAL or NTS C display. Note that this requires a system with min imum one DVI-I output.
Peripheral Equipment 255 6.11 VESA Display Power Management Because of the tremendous amount of energy co ns um ed by monitors when operating, the system will reduce power consu m p tion and extend monitor lifecycle by su spending the (switch off) monitors and projectors when the syste m goes into sleep/standby.
TANDBERG 7000 MXP 256 6.12 Digital Monitor Power Management DMPM is monitor power management a pplied over the digital DVI interface. TANDBERG supports DMPM in softwar e F2 and ab ove. Six monitor power stat es are defined. Monitor On Power state Transmitter (TANDBERG codec) and receiver (Moni t or) a re powered and active.
Peripheral Equipment 257 6.13 Extended Display Identification Data (EDID) Extended Display Identification Data (EDID) is a VESA standard data format that will allow the system to communicate its ca pabilities, including vendor information like the supported VGA - formats and frequency range limits to a PC con ne cte d to the XGA/DVI input.
TANDBERG 7000 MXP 258 Tested and verified monitors, EDID & Timing Listed below are some of the monitors TANDBERG h ave tested an d verified against: ADI A715 Dell W1700 Dell W1900 EIZO L367 EIZO F.
7 Appendices Appendices: Appendix 1: Technical Specification Appendix 2: Bandwidth Information Appendix 3: Environmental considerations Appendix 4: Guidelines for setting up rooms for .
TANDBERG 7000 MXP 260 Appendix 1: Technical Specifications Technical Specification UNIT DELIVERED COMPLETE WITH: 2 x 30" widescreen LCD monitors, wireless remote control, Tracker, W.A.V.E. II camera, microphone, Audio ModuleTM, integrated cabling and stand MONITORS Dual 30" LCD monitors 16:9 high resolution widescreen format BANDWI DTH H.
Glossary 261 VIDEO FORMAT NTSC, PAL, VGA, SVGA, XGA, W-XGA, SXGA and HD720p LIVE VIDEO RESOLUTIONS NATIVE NTSC: 400p (528 x 400 pixels) 4SIF (704 x 480 pixels), Digital Clarity Interlaced SIF (iSIF 35.
TANDBERG 7000 MXP 262 DUAL STREAM DuoVideo H.239 Dual Stream Available on H.323 & H.320 Available in Multisite from any site Dynamic bandwidth adjustment (H.
Glossary 263 Appendix 2: Bandwidth Information for TANDBERG Endpoints Bandwidth information for TANDBERG endpoints Model 8000MXP, 7000MXP 6000MXP, Maestro Bandwidth Point to point ISDN / IP Standard: .
TANDBERG 7000 MXP 264 H.264 Up to 2Mbps Up to 2Mbps Picture Mode MultiSite VS, CP4, CP5+1 VS, CP4, CP5+1 Model 990MXP / 990NET MXP 880MXP / 880NET MXP Bandwidth Point to point ISDN / IP Standard: 1920.
Glossary 265 Appendix 3: Environmental Considerations Environmental considerations This section explains how to carry out basi c adju s tments and simple tests to en sure that you send and receive the best possi ble image and audio qualit y when u sing your system.
TANDBERG 7000 MXP 266 Appendix 4: Guidelines for Setting up Rooms for Video Meetings Guidelines for setting up rooms for video meetings The following are a set of guidelines to consider whe n either building a video meeting roo m, or using an existing room for video meetin g s.
Glossary 267 How to prepare a typical room for videoconfere nc ing: The diagram below shows a typical room desig ned to obtain the best re sults when using the system. The microphone should be placed at the front of the table to ensure that all speech will be detected.
TANDBERG 7000 MXP 268 Appendix 5: Security Security The system has several features both to prot ect fro m unauth orized use and sy stem access: Access Code: When Access Code is enabled, the user will be as ked to enter an access code before he/ she is able to make a call.
Glossary 269 IP Password By setting an IP Access Password on the s ystem, all access to the system using IP (Telnet, FTP and WEB) requires a pa ssword. This p assword can be enabled from telnet or dataport u sing the command: ippassword <ip-passwo rd >.
TANDBERG 7000 MXP 270 mechanisms employed by TANDBE R G are: AES, DES, H.233, H234 and H.235 (H235v3 & v2 for backwards compatibility) with extended Diffie Hellma n key distribution via H.
Glossary 271 Appendix 6: Using the File System Using the file system It is possible to access a file sy stem within the TANDBERG sy stem by using ftp: DOS- window: ftp <IP-address of system >, or Web- browser: ftp:// <IP-address of system> Description of the different files: all.
TANDBERG 7000 MXP 272 Appendix 7: Web Interface Web Interface It is possible to access and maintain the system remot ely via a local area network (LAN) usin g a standard Web-browser. Conne ct your syste m to a LAN with a Network cable. How to configure your system for web interface: 1.
Glossary 273 Appendix 8: Connecting the System to PRI/T1 (Not available on all TANDBERG systems) Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1-inte rfa ce using an Adtran T1 ESF CSU ACE or equivalent CSU, will allow up to 1.
TANDBERG 7000 MXP 274 Appendix 9: Connecting the System to the Switched 56 Network Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adap ter Connecting the system to the SW56 net work u sing a Telesync Adapter is descri bed bel ow.
Glossary 275 Appendix 10: Connecting the System to ISDN using NT1 Network Adapters Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on t he syst em to the S-interface on your first NT1 network adapte r.
TANDBERG 7000 MXP 276.
Glossary 277 Appendix 11: TANDBERG Cameras TANDBERG Precision HD Camera (Available to TANDBERG 8000 M XP, 6000 MXP Prof ile, 3000 MXP Profile*, Maestro MXP and Edge 75/85/95 MXP) Pin-outs and Connecto.
TANDBERG 7000 MXP 278 1. Extra Camera In 2. 12V DC Power In 3. HD Video Out, HDMI** 4. Codec – HD Video Out 5. Kensington Lock NOTE! The enclosed TANDBERG Camera Cable s m ust be used! Do not use other camera cables as this might cause problem s with the tr ansfer of video signals from the Precision HD Camera.
Glossary 279 The maximum length of the camera cable for mult iple cameras supported by TA NDBERG is 20 m (65 ft). * Applies to T3000 MXP Profile with new hardware. ** Disabled when connected to a TANDBERG system using the TANDBERG Ca mera Cable. This output does not support HDCP (High Bandwidth Digital Content Protection).
TANDBERG 7000 MXP 280 Top view:.
Glossary 281 (Not available with set top systems) WAVE II Camera Pinouts and Connectors 8-PIN RJ (shielded modular jack): This connector is u sed fo r the power and control signals to the main camera.
TANDBERG 7000 MXP 282 Pin-5 GND Pin-4 RXD (in) Pin-3 TXD (out) Pin-2 Presence (+12V in daisy chain) Pin-1 GND Multiple Camera support: The figure below is an example of how mu ltiple cam eras should b.
Glossary 283 Dimensions Front view: Sid e view : Re ar view : Underside vie w :.
TANDBERG 7000 MXP 284 Appendix 12: Remote Control (TRC3 / TRC4) Remote Control (TRC 3 / TRC4) The TANDBERG remote control transmits IR -signals usin g the following parameters: Protocol Siemens SDA220.
Glossary 285 Remote Control key code map: Button codes Remote Control (TRC 3) Remote Co n trol (TRC 4) TANDBERG TRACKER Dec Hex Address Button name Address Button name Address Button name 0 0 1 1 0 NU.
TANDBERG 7000 MXP 286 32 20 0 RIGHT 0 RIGHT 33 21 0 OK 0 OK 34 22 0 CALL 0 CALL 35 23 0 END CALL 0 END CALL 36 24 0 PHONE BOOK 0 PHONE BOOK 37 25 0 MENU 0 MENU 38 26 0 CANCEL 0 CANCEL 39 27 0 0 40 28 .
Glossary 287 Appendix 13: Cisco CallManager Registration Cisco CallManager registration Configuring an H.323 client on the CallManager 4.0 The registration of a H.323 client in CallM anager is supported on t he CallManager (CCM) 4. 0 software and forward.
TANDBERG 7000 MXP 288 Appendix 14: Diagnostics Tools for IP Diagnostic Tools for IP To use these tools, will require u sing a P C and setting up a telnet session towards the syste m. Q.931 To show Q.931 trace during a call you n eed to issue the command ‘syslo g on’.
Glossary 289 Function Port Typ e Gatekeeper Discovery (RAS) 1719 UDP Q.931 Call Setup 1720 TCP H.245* Range 5555-5574 TCP Video Range 2326-2405 UDP Audio Range 2326-2405 UDP Data/FECC Range 2326-2405 .
TANDBERG 7000 MXP 290 Appendix 15: System Upgrade System Upgrade Before starting the software upgrade of the TA NDBE RG MXP system, please make sure to have the new software file, (for instance s0500 00F 30.pkg ) a nd the Rel ease Key for this software available.
Glossary 291 Figure 1 3. Enter the Release key in the ‘Release Key’ field and press the ‘Install Software’ button..
TANDBERG 7000 MXP 292 A new page will now be displayed: Figure 2 4. Type in the path to where the new software file is stored, or sel ect the file by using the ‘Browse’ button. 5. The progress for the sw upgrade can be tracked by pressing the ‘telnet’ link in the help text box BEFORE pressing the install button.
Glossary 293 5. Type in your IP password (def ault is “TANDBERG”) a s pa ss word. 6. Type ‘put <software file name> and press Ente r. The new software file will now be uploaded to the TANDBERG MXP system. 7. When the software upload is com plete, end the ftp connection to the TANDBERG MXP system by typing ‘bye’ in the DOS prompt.
TANDBERG 7000 MXP 294 The following page will now be di splaye d: Figure 3 5. Enter the release key for the system to be upgraded in the ‘Rele ase Key’ field. If no release key is given, the Far End System will use the prev iously stored release key if possible.
Glossary 295 In the menu on the system under ‘Control Panel /System Information ’, the installed software should now be displayed as the ‘Software Versi on’.
TANDBERG 7000 MXP 296 Appendix 16: Declaration of Conformity EC DECLARATION OF CONFORMITY MANUFACTURER: TANDBERG Telec om AS PRODUCT NAME: TANDBERG 7000MXP TYPE NUMBER: TTC60-05 DESCRIPTION: Video Con.
Glossary 297 Appendix 17: Dimensions Dimensions.
TANDBERG 7000 MXP 298 Appendix 18: Protocols Supported PROTOCOLS SUPPORTED TCP/IP - Transmission Control Protocol/Internet Protocol A set of networking protocols that provi des conn ectivity over LAN/WAN to any network computer. HTTP - Hypertext Tran sfe r Protocol A protocol used to transfer information on the in ternet.
Glossary 299 WAN – Wide Area Net work A communications network conn ecting geographically separated computers, printers, and othe r devices. SSL - Secure Sockets Layer SSL is a proposed open st anda rd for establishing a secure commu nications channel to preve nt the interception of critical information.
TANDBERG 7000 MXP 300 Appendix 19: Cable Specifications TANDBERG MXP and Classic E ndpoints that support External Network External Network Pinout With respect to signals on the NET port: • For balanced signals a “0”=low voltage i s defined as terminal A positive with respect to terminal B.
Glossary 301 Cable Specification V.35 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on cable at Codec en d: o Female 2 6 pi n high-density DSUB with thumbscrews. • Connectors on cable at V.35-adapte r en d: o Male 34 pin Winchester (AMP part number 2013 57-1 or equivalent).
TANDBERG 7000 MXP 302 Cable Specification V.35/RS-366 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on cable at Codec en d: o Female 2 6 pi n high-density DSUB with thumbscrews.
Glossary 303 Cable Specification RS-449 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or E.
TANDBERG 7000 MXP 304 Cable Specification RS-449/RS-366 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark .
Glossary 305 Cable Specification RS-530 Cable TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F2055 or E.
TANDBERG 7000 MXP 306 Cable Specification RS-530/RS-366 TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50.
Glossary 307 Cable Specification RS-449 Cable to KIV-7 TANDBERG MXP and Classic E ndpoints that support External Network • Connector on Tandberg End: o Female 2 6pin High Density DSUB Newark P/N 50F.
TANDBERG 7000 MXP 308 8 Glossary # 199 AV1: External input for the TANDBERG/LOEWE monitor. 2nd monitor: The second monitor of yo ur video conferencing system .
Glossary 309 B Bandw idth: Decides the quality of the video call. High bandwidth gives high q uality. C Call Control Data Triggered: Uses TxData, RxData and clock signals o nly.
TANDBERG 7000 MXP 310 Diagnostics: Allows testing of individual system co mponents an d displ ays the current system settings. Digital ClarityTF: Participants enjoy presentations o f ex ceptionally high quality resolution video. Disconnect site: As a Chairma n, you get the option Disco nnect site.
Glossary 311 G G.711: Audio algorithm for normal qualit y audio (tel ephone quality, 3.1 kHz) The system will always have G.711 enabled. G.722: Audio algorithm for high quality audio (7 kHz). G.722.1: Audio algorithm for compressed high qu ality audio (7 kHz) G.
TANDBERG 7000 MXP 312 Main Camera: Your camera. Video input 1 Max call length: This feature will automatically end both incomin g and outgoing calls when the call time exceeds the length specified. Max channels: Indicates the maximum numbe r of channels the sy stem is allo wed to use on the E1/T1 interface.
Glossary 313 NR: Noise Reduction. Re duces constant background noise (e.g. noise from air-conditioning systems, cooling fans, etc. ). NSF: Non Standard Facility. NTSC: National Television System Committee. Video standard co rresponding to 4SIF. Primary used in USA, Japan and other countrie s.
TANDBERG 7000 MXP 314 Restore defaults: Re stores system settings to the factory defaults. Restricted call: A call to a 56 kbps network. By default t he system will dial an unrestricted call (a call to a 64 kbps network) and down speed to 56 kbps if necessary.
Glossary 315 Streaming TTL/Router Hops: Used for streaming d ata to limit how many ro ute rs the data should pass before it is rejected. Streaming Video Rate: Defines the Video strea ming rate from the system.
TANDBERG 7000 MXP 316 Welcome menu: The welcome menu di splays the Menu when you are outside a call. X XGA: extended Graphi cs Array (1024 x 768).
Index 317 9 Index A Access Co de....................................100, 123 Additional mi cropho ne ............................. 244 Administrator Passwo rd ...........................139 Alert S peaker ...........................................182 Alert Tones a nd Volu me .
TANDBERG 7000 MXP 318 Postpone 1 hour ........................................ 51 Postpone 3 hours....................................... 52 Precision HD Came ra .............................. 277 Presentation Presentation Key ........................
デバイスTANDBERG 7000 MXPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TANDBERG 7000 MXPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTANDBERG 7000 MXPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TANDBERG 7000 MXPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TANDBERG 7000 MXPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TANDBERG 7000 MXPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTANDBERG 7000 MXPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TANDBERG 7000 MXPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTANDBERG 7000 MXPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
