TangentメーカーTNR-50の使用説明書/サービス説明書
ページ先へ移動 of 20
TNR-50 FM/AM tuner Instruc tion m anual.
01 ACCESSORIES Accessories 1 x TNR-50 1 x Remote control 2 x Batteries (Optional) 1 x FM Antenna (Optional) 1 x Operation Manual This operation manual supplies all the information that you need to have about your T angent TNR-50.
02 CONTENTS ACCESSORIES CONTENTS SAFETY PRECAUTIONS IMPORT ANT SAFETY INSTRUCTIONS IMPORT ANT INFORMA TION CONNECTION REMOTE CONTROL FRONT P ANEL AND CONNECTIONS CONNECTION Accessories 01 Contents 02 .
TO MINIMISE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET AS IT CONT AINS DANGEROUS VOL T AGE.
W ARNING: IT IS IMPORT ANT THA T YOU READ AND OBSERVE BOTH THE INSTRUCTIONS IN THIS MANUAL AND THE INSTRUCTIONS ON THE UNIT . KEEP THIS MANUAL FOR FUTURE REFERENCE. This unit was designed and manufactured with a view to providing maximum safety for the user .
Service Do not attempt to carry out any service work yourself. By opening or removing the cabinet, you will be exposed to dangerous voltage or other hazards.
IMPOR T ANT INFORMA TION Handling instructions The top and back panel of the unit may become warm after prolonged use. This is not due to a defect. T urn off the power when the unit is not used.
07 CONNECTION Connection to the mains Do not turn on the power before all connections have been made correctly . Check that all connections have been made correctly before turning on the power . Check that the mains voltage is 230-240V AC50Hz before turning on the power .
08 REMOTE CONTROL Installation of batteries Remove the cover as illustrated. Position two batteries of the type AAA/R03/UM4 in the battery compartment. Make sure that the orientation of the batteries is correct (see drawing at bottom). Replace the cover .
09 Some of the functions of the unit can only be performed by means of the remote control. Some functions are connected with the selected signal input source. Some buttons on the remote control may therefore not be available if the corresponding signal input source has not been selected.
8 9 10 1 2 3 4 5 6 7 10 FRONT P ANEL AND CONNECTIONS Front panel Mains switch: LED indicator: FM/AM: Autotune: Memory: Preset -: Preset +: St/Mono: Reset: T uning: Used to interrupt the mains voltage. Lights green when the unit is turned on. Lights red when the unit is in standby mode or in operation.
11 FRONT P ANEL AND CONNECTIONS Connections 1 2 3 Stereo Output: Antenna AC input Analogue stereo output. For connection to stereo amplifier or receiver with analogue input. : For connection of FM or AM antenna or for the communal antenna system. : For connection of mains voltage.
12 CONNECTION Audio connection layout FM ANTENNA AM TNR PHONO TUNER DVD CD AUX 1 AUX2 FUNCTION VOLUME POWER HEADPHONE AMP-50 AMPLIFIER Analog amplifier/receiver This page only contains suggestions for connection of your T angent TNR-50. Note that the accessories in the pictures on this page are not included in the supply .
13 FM ANTENNA AM FM ANTENNA AM ADJUSTING THE ANTENNA Adjusting the antenna For an optimal result it is recommended to install a FM antenna on the roof or on the loft. The FM antenna must be adjusted for the best possible result. A good tip is to let the antenna end point in a vertical direction and fix it on a wall.
14 + AUTO TUNE + TUNE PRESET MEMO FM AM ST/MO RDS POWER TNR-50 PHON POWER TNR-50 FM/AM TUNER 1 3 3 T urn on the unit by pressing the mains switch. Press the standby button on the remote control to switch to standby mode. The display will turn of f and all functions will be reduced to a minimum to make sure that the unit uses minimal power .
15 OPERA TION AND FUNCTIONS + AUTO TUNE + TUNE PRESET MEMO FM AM ST/MO RDS POWER TNR-50 -P R E S E T+ MEMORY AUTOTUNE FM/AM ST/MONO RESET TUNING T uning 1 2 2 1 If you want to manual tune a channel, you must press the tune + or - button on the remote control, or turn the tuning knob on the front panel.
16 OPERA TION AND FUNCTIONS This tuner can be reset. This is used to delete channel stored in the unit. Press the RESET button on the front panel to reset the unit.
17 TROUBLESHOOTING T roubleshooting PROBLEM CAUSE/REMEDY No power when the unit is turned on. - Switch on the electric current at the socket. - Check that the plug has been correctly inserted into the socket. - The internal fuse has blown and must be replaced by a qualified service technician.
18 TECHNICAL DA T A T echnical data RF section: T uner bands FM 87.5-108.0MHz AM 522-1620KHz Sensitivity -96dBm type 2 lines of 16 characters LED backlight 40 Stereo, 2.5Vpp 48kHz sample rate 16 bit sample resolution See back panel 430 x 290 x 75mm 4.
F or fur ther inf ormation please visit our website: www .tangent-audio.c om I tem no . 40427 Ser vice hotline +45 9641 1599.
デバイスTangent TNR-50の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Tangent TNR-50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTangent TNR-50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tangent TNR-50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tangent TNR-50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tangent TNR-50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTangent TNR-50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tangent TNR-50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTangent TNR-50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。