TatungメーカーTLM1905の使用説明書/サービス説明書
ページ先へ移動 of 28
OPERATING INSTRUCTIONS TLM-1705 / TLM1905.
.
i P REFACE FCC Compliance Statement This device complies with part 15 of the FCC Rules. Opeartion is sub jected to the following two co nditions: 1. This device may not cause harmful int erference, and 2. This device must accept any interfe rence received, including interference that may cause undesi red operation.
ii The Federal Comm unications Com mission warns that changes or modificati ons of the unit not expressly approved by the party responsible for com pliance could void the user’s authority t o operate the equipment .
iii Important Operating Instructions Please read the following instructi ons carefully. This m anual should be retained for future use. 1. To clean the LCD monitor screen, first, make sure the monitor is in the power off mode. Unplug the m onitor from its power source before cleaning it.
iv Introduction CONTENTS PREFACE ..................................................................................................................... I CHAPTER 1 ........................................................................................
1 C HAPTER 1 The LCD Multimedia Monitor Unpacking After you unpack you r LCD multimedia monitor, m ake sure the following items are included in the box and in good condition: Standard Item • LCD mul.
2 Identifying Components The LCD Multimedia Monitor — Front View Figure 1-1: The LCD multimedia Monitor Front View 1. Power-On Indicator This LED indicator stays lit when th e power is on and b links when the LCD multimedia monitor is in power saving mode .
3 1. Audio Line-in 2. AC Power Jack 3. VGA (Analog) Cable With 15-Pin D-Sub VGA Connector (Male) 4. S-Video connector 5. AV connector 6. Digital VGA (DVI) Cable Connector (Optional) Adjusting the Tilting Angle The LCD multimedia monitor’s angle settings range from -3 ° to 20 ° .
4 Raising Your Monitor to an Upright Position and Adjusting Monitor Angle.
5 Power Management System The LCD multimedia monitor complies with the VESA DPMS power management proposal. When the LCD multimedia monitor is in power saving mode or detects an incorrect timing, the monitor screen will be blank and the power LED indicator starts blinking.
6 C HAPTER 2 The Display Controls LCD Multimedia Monitor Control Panel Figure 2-1: The LCD Monitor Panel 1. OSD Menu Button Press this button to pop up the OSD (On-Screen Di splay) me nu. This button is also a Funct ion Select button . 2. Adjustment Control Buttons These two buttons allow you t o adjust the selected control functions in the OSD.
7 Adjusting the Monitor’s Display OSD Main Menu To access the OSD main m enu, press the OSD Menu button. Use the Function Select buttons to scroll b etween the OSD main menu options.
8 H-POSITION: To move the LCD m onitor’s display left or right on a horizontal plane. V-POSITION: To move the LCD m onitor’s displa y up or down on a vertical plane. PHASE: To adjust the focus and clarity of the display. CLOCK: To adjust the d isplay pixel alignment.
9 EXIT: To exit the OSD-Control submenu. GRAPHIC-CONTROL Option The Graphic-Control option l ets you ma ke adjustments that effect the contrast, brightness and color of the LCD m onitor’s display. Press the Adjustment control button to displ ay the submenu.
10 Press the Adjustment control button to displ ay the submenu. LANGUAGE: The supported languages include Germ an, English, French, Spanish, Itali an and Japanese. AUDIO VOLUME: To increase or decrease the volume of the LCD monitor’s sound sy stem. INFORMATION: To indicate display mode tim ings and firmware version.
11 OSD-CONTROL Option The OSD-Control m enu option lets y ou adjust the position of the OSD on the screen. Press the Adjustment control button to displ ay the submenu. Use the Function Select buttons to select one of t he following submenu options: OSD-H-POSITION: To change the position of the OSD on a horizontal plane.
12 MISC-CONTROL Option The Misc-Control m enu option let s you select the OSD display language, adjust the audio volume set ting and view system informati on. Press the Adjustment control button to displ ay the submenu. LANGUAGE: The supported languages include Germ an, English, French, Spanish, Itali an and Japanese.
13 EXIT: To exits the Monitor-Control subm enu. OSD-CONTROL Option The OSD-Control m enu option lets y ou adjust the position of the OSD on the screen.
14 SATURATION: To adjust the color level you prefer. SHARPNESS: Press the adjustment button to optimize the sharpness for your specific applicati on. RESET: To reset all of the Video-Control submanu settings t o the factory default. EXIT: To exit the Video-Control subm enu.
15 Note: 1. No Video When the monitor is ON and th ere is no Video signal received, the following message will be displayed. 2. Signal out of monitor’s support ed range (Please refer to Addendum) Wh.
16 Hot-Key Buttons for Quick Adjustment of Monitor Settings. ( 〝 AUTO-ADJUST 〞 hot-key is effective only when analog input signal is selected for application) 1. " Auto-adjust " hot-key button: Press button 2 to apply the m onitor setti ng automatically.
17 A PPENDIX A Troubleshooting Troubleshooting Procedures This LCD monitor come s pre-adjusted w ith standard VGA timing. Due to output timing differences among various VGA car ds, you may initially experience an unstable or unclear display when a new display m ode or new VGA card is selected.
18 2. Turn off the LCD monitor and then turn it back on again. Press the OSD Menu button (refer to Chapt er 2) once and then press either Adjustment Control button several times. If there is still no display, press the other Adjust ment Cont rol button several times.
19 A PPENDIX B Technical Information LCD Monitor Specifications LCD Panel 17-inchTFT Control Functions Power Software switch w ith LED indicator (toggle ON/OFF) Main Menu Submenu ANALOG MODE : MONITOR.
20 Display Area 337.920 mm x 270.336 mm (17.0-inch diagonal) Display Colors 16M Video Input VGA, DVI (O ptional), S-Video, AV Scanning Frequency (Analog mode) 24-80K 56-75 Scanning Frequency H/V, Hz (Digital mode)- (Optional) 31-80K 56-75 Power Management Meets VESA DPMS Power Consumption ON : 40W max.
21 A PPENDIX C Supported Timing Ite m Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) Sync Polarity or composite sy nc (H/V) Operatin g Mode 1 NEC PC98 640x400 25.20 70.15 31.50 -/- A/D 2 NEC PC98 640x400 21.
6200564280 TATUNG COMPANY OF AMERICA 2850 El Pres i d i o ST. Long Beach, CA 90810 (800) 827-2850 www.tatungusa.com.
デバイスTatung TLM1905の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Tatung TLM1905をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTatung TLM1905の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tatung TLM1905の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tatung TLM1905で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tatung TLM1905を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTatung TLM1905の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tatung TLM1905に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTatung TLM1905デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。