TektronixメーカーVX4801の使用説明書/サービス説明書
ページ先へ移動 of 91
User Manual VX4801 Pr ogrammable Digital I/O Module 070-9153-03 This document applies for firmware version 1.00 and above..
Copyright T ektronix, Inc. All rights reserved. T ektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved.
W ARRANTY T ektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years from the date of shipment.
EC Declaration of Conformity We T ektronix Holland N.V . Marktweg 73A 8444 AB Heerenveen The Netherlands declare under sole responsibility that the VX4801 meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility .
.
.
$$# $ " "$ !$ # 0641'.
VX4801 Programmable Digital I/O Module iii General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. Only qualified personnel should perform service pr ocedur es.
General Safety Summary iv VX4801 Programmable Digital I/O Module Safety T erms and Symbols These terms may appear in this manual: W ARNING. W arning statements identify conditions or practices that could r esult in injury or loss of life.
.
.
.
.
.
.
.
.
.
.
Output high voltage (V oh ) min typ max units I o = –20 A l o = –6 mA Output low voltage (V ol ) l o = 20 A l o = 24 mA Output low current (l ol ) Input high voltage (V ih ) Input low voltage (V il ) * Input current (l in ) T ri-state leakage current (l oz ) 4.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
VX4801 Programmable Digital I/O Module A–19 Appendix E: Performance V erification 123 This procedure verifies the performance of the VX4801 Programmable Digital I/O Module. The test sequences may be performed in your current VXIbus system if it meets the requirements described in T able 2.
Appendix E: Performance V erification A–20 VX4801 Programmable Digital I/O Module NOTE . Commands to the VX4801 may be enter ed in upper or lower case. However , to avoid confusion between the alphanumeric characters; e.g. one (1) and L or zer o( 0) and o, all commands ar e shown in the case which pr ovides the gr eatest distinction.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–21 34 18 1 Byte 3 LSB Byte 2 MSB Byte 5 LSB GND Byte 0 LSB DAK 6 DA V 5 GND GND GND 1 34 39 50 33 17 1 14 25 13 8 Byte .
Appendix E: Performance V erification A–22 VX4801 Programmable Digital I/O Module VX4801 Under-T est Configuration In order to perform this procedure, the VX4801 under-test must be installed in an approved VXIbus system. At a minimum, the system must contain the elements listed in T able 2.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–23 T est Record Photocopy the T est Record, and use it to record the performance verification results for your module.
Appendix E: Performance V erification A–24 VX4801 Programmable Digital I/O Module Self T est The VX4801 includes a built-in self test function (BITE) which is automatically executed each time the power is turned on and when the Internal Self T est (S) command is issued.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–25 NOTE . If you ar e using National Instruments NI-488.2 softwar e you may wish to select the buffer 1 mode to allow mor e comfortable viewing of the ASCII r esponse. Just type buffer 1.
Appendix E: Performance V erification A–26 VX4801 Programmable Digital I/O Module (Observe: VX4521 Slot 0 indicates S in 2nd digit) NOTE . The zer o length r ead serves to un-addr ess the Slot 0 controller which allows it to detect the VXIbus interrupt and assert the SRQ.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–27 2. Perform a self test and query for any error codes (in ASCII format) with the VX4801 device-under-test and the Sla.
Appendix E: Performance V erification A–28 VX4801 Programmable Digital I/O Module 4. T o verify the even byte data inputs and the odd byte data outputs, reset the VX4801 to its power-up state and th.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–29 (Observe: response of 00FF00FF00FF) b.
Appendix E: Performance V erification A–30 VX4801 Programmable Digital I/O Module (Observe: response of 00FF00FF00FF) d.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–31 This test sequence verifies that data can be transferred to and from the VX4801 using the four handshake signal lines Data Ready (DRD), Data Acknowledge (DAK), Ready for Data (RFD), and Data A vailable (DA V).
Appendix E: Performance V erification A–32 VX4801 Programmable Digital I/O Module d. Set the Slave to initialize byte 2 with an Output Data value of 01 (asserts RFD to the VX4801) and verify that the VX4801 correspondingly asserts DA V : (Observe: VX4801 DA V light on) e.
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–33 e. Send a byte 5 input command to the VX4801 and verify that the DAK light is on.
デバイスTektronix VX4801の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Tektronix VX4801をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTektronix VX4801の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tektronix VX4801の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tektronix VX4801で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tektronix VX4801を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTektronix VX4801の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tektronix VX4801に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTektronix VX4801デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
