Texas InstrumentsメーカーUCC2891の使用説明書/サービス説明書
ページ先へ移動 of 20
48-V to 3.3-V Forward Converter with Active Clamp Reset Using the UCC2891 Active Clamp Current Mode PWM Controller User's Guide December 2006 Power Supply MAN SLUU178A.
48-V to 3.3-V Forward Converter with Active Clamp Reset Using the UCC2891 Active Clamp Current Mode PWM Controller User's Guide Literature Number: SLUU178A November 2003 – Revised December 2006.
1 Introduction 2 Description User's Guide SLUU178A – November 2003 – Revised December 2006 Using the UCC2891 Active Clamp Current Mode PWM Controller The UCC2891EVM evaluation module (EVM) is a forward converter providing a 3.3-V regulated output at 30 A of load current, operating from a 48-V input.
www.ti.com 2.1 Applications 2.2 Features Description The UCC2891 is suited for use in isolated telecom 48-V input systems requiring high-efficiency and high-power density for very low-output voltage, .
www.ti.com 3 UCC2891EVM Electrical Performance Specifications 4 Schematic UCC2891EVM Electrical Performance Specifications The UCC2891EVM electrical performance specifications are listed in Table 1 .
www.ti.com + + + + Schematic Figure 1. UCC2891EVM Schematic 6 Using the UCC2891 Active Clamp Current Mode PWM Controller SLUU178A – November 2003 – Revised December 2006 Submit Documentation Feedb.
www.ti.com 5 EVM Test Setup V 2 - + J 1 + V out -V out J 9 J 10 Loo p+ Loo p- J 6 J 7 T exas I ns trum e nts H P A 03 4 U C C 2891 A c ti v e C l am p C onver te r J 3 V -C l am p J 2 Q 2 G ate J 4 SR -Q F G ate J 5 SR -Q R G ate LO A D 1 3.
www.ti.com 5.1 Output Load (LOAD1) 5.2 DC Input Source (VIN) 5.3 Network Analyzer 5.4 Recommended Wire Guage 5.5 Fan EVM Test Setup For the output load to VOUT, a programmable electronic load set to constant current mode and capable of sinking between 0A DC and 30A DC , is used.
www.ti.com 6 Power Up/Down Test Procedures Power Up/Down Test Procedures The following test procedure is recommended primarily for power up and shutting down the EVM. Whenever the EVM is running above an output load of 15 A DC , the fan should be turned on.
www.ti.com 7 Power Up/Down Test Procedures 81 79 87 83 91 89 93 85 2 6 18 26 22 10 14 I OUT - Output Current - A V IN = 36 V V IN = 72 V V IN = 48 V Percent Efficiency - % V OUT = 3.
www.ti.com t − T ime − 2.5 µ s/div V IN = 36 V I OUT = 30 A 500 mV/div 1 V peak-to-peak Input Ripple V oltage 10 -40 -60 100 1 k 10 k 100 k 0 -20 40 20 60 -120 -180 0 -60 120 60 180 V IN = 48 V I OUT = 10 A g M = -10 dB F M = 50° Gain Phase f - Frequency - Hz Gain - dB Phase - ° GAIN A ND PHA SE vs FREQUENCY t − T ime − 2.
www.ti.com t − T ime − 1 µ s/div V IN = 36 V 6.3 V , QF Gate (J5) (5 V/div) 8.4 V , QR Gate (J6) (5 V/div) SR Gate Drive t − T ime − 2.5 µ s/div V IN = 36 V I OUT = 30 A 50 mV/div 23 mV peak-to-peak Output Ripple V oltage t − T ime − 1 µ s/div V IN = 72 V 12.
www.ti.com 8 EVM Assembly Drawing and Layout EVM Assembly Drawing and Layout Figure 14 through Figure 20 show the top-side and bottom-side component placement for the EVM, as well as device pin numbers where necessary.
www.ti.com EVM Assembly Drawing and Layout Figure 15. Top Side Silk Screen Figure 16. Top Signal Trace Layer 14 Using the UCC2891 Active Clamp Current Mode PWM Controller SLUU178A – November 2003 .
www.ti.com EVM Assembly Drawing and Layout Figure 17. Internal Split Ground Plane Figure 18. Internal Signal Trace Layer SLUU178A – November 2003 – Revised December 2006 Using the UCC2891 Active C.
www.ti.com EVM Assembly Drawing and Layout Figure 19. Bottom Signal Trace Layer Figure 20. Bottom Side Component Assembly Using the UCC2891 Active Clamp Current Mode PWM Controller 16 SLUU178A – Nov.
www.ti.com 9 List of Materials List of Materials The following table lists the UCC2891EVM components corresponding to the schematic shown in Figure 1 . Table 2. List of Materials QT REF DESCRIPTION MFR PART NUMBER Y C1, C2, C4 3 Capacitor, ceramic, 2.
www.ti.com 10 References References Table 2. List of Materials (continued) QT REF DESCRIPTION MFR PART NUMBER Y R1 1 Resistor, chip, 8.45 k Ω , 1/10 W, 1%, 805 Vishay CRCW0805-8451-F R2 1 Resistor, chip, 57.6 k Ω , 1/10 W, 1%, 805 Vishay CRCW0805-5762-F R3 1 Resistor, chip, 76.
EVM IMPORT ANT NOTICE T exas Instr ument s (TI) provi des the encl osed product (s) under the f oll owing condi ti ons: This eval uati on kit bei ng sold by TI is i ntended for use for ENGI NEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fi t f or commer cial use.
DYNAMIC W ARNINGS AND RESTRICTI ONS It is impor tant to oper ate thi s EVM wit hin t he input voltage r ange of 0 Vdc t o 72 Vdc. Exceeding t he specif ied input r ange may cause unexpected oper ati on and/or i rr eversi ble damage to the EVM.
デバイスTexas Instruments UCC2891の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Texas Instruments UCC2891をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTexas Instruments UCC2891の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Texas Instruments UCC2891の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Texas Instruments UCC2891で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Texas Instruments UCC2891を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTexas Instruments UCC2891の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Texas Instruments UCC2891に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTexas Instruments UCC2891デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
