The Eltron CompanyメーカーLP2022の使用説明書/サービス説明書
ページ先へ移動 of 48
User’s Manual No. 980008-001 Rev. B ©1995 Eltron In ternatio nal Inc. LP/LP+ Series User’s Manual Models: LP2022, LP2042 LP2122, LP2142.
.
FOREWORD This manual provide s installati on and operation info rmation for LP & LP+ Se ries printers manufact ured by Eltron Int ernationa l Incorporated, Sim i Valley, Califo rnia. The cont ents includes instal lation & opera tion inst ructions.
WARRANTY INFORMATION We Need To Hear From You! To establis h your warr anty period and provi de access to Tec hnical Suppo rt, Send Us Your Product Registrati on Card Today! Eltron warrants the mechan.
Table Of Contents Getting Started Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . 2 Parts Check List . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . .
vi 980008 -002 Rev. B.
1 Getting Started This section provides information on the instal- lation of the printer and software. Introduction The LP Series and LP+ Series printers are low cos t dir ec t th erma l print er s sp.
Unpacking the Printer The printer is shipped in a carton and protec- tive bag. Keep all packing material in case you need to move or re-ship the printer. Avoid touching the electrical connectors to prevent Electro-Static Discharge damage while setting up the printer.
Parts Check List Your printer kit should contain the items listed below. • The LP or LP+printer. • The printer Power Supply. • Create-A-Label Tools software disk & man- ual (LP+ only). • Printer User’s Guide (this manual). • 1 roll of Sample Labels and Spool.
Installation The following sections will step you through the installation of the printer and Create-A-Label Tools software. Step ➊ Attach Power Supply Place the printer in a suitable location that allows easy access to printed labels. The printer should never be operated while resting on it’s side or upside down.
Step ➋ Insert Memory Cartridge (LP+ Only) The memory /real-time clock cartridge pro- vid es permanent storage for downl oaded forms and time/date information. Cartridges are available in four upgradable memory con- figurations: 128KB, 256KB, 384KB & 512KB.
Step ➌ Attach Interface Cable Parallel Interface Attach a suitable parallel printer cable from the computer to the Centronics interface connector on the rear of the printer. Serial Interface Attach a suitable serial printer cable from the computer to the DB-9 RS-232 Serial interface connector at the back of the printer.
Step ➍ Install Software (LP+ Only) Start your computer. After DOS has loaded, insert the Creat-A-Label Tools diskette into your floppy disk drive. From the DOS prompt, enter B:INSTALL (or A:INSTALL if you placed the diskette in drive A). Press the Enter key.
Getting Started 8 980008 -001 Rev. B.
2 Operation This section provides information on the op- eration of the LP and LP+ printers. Controls & Indicators The printer’s power switch is located on the rear of the unit near the power cord. Placing this switch in the “1" (ON) position will apply power to the printer.
Power Switch Figure 2-1 Controls & Indicators Power Indicator Feed Control Tension Release Push Back To Release Label Taken Sensor Operation 10 980008 -001 Rev.
The FEED Control The FEED control can be used in two ways, tapping or holding . When power is first ap- plied to the printer, tapping the FEED control will cause the paper to advance approximately 0.25". This condition is refereed to as a Line Feed.
Loading Labels or Tags Your printer can print on adhesive backed labels or non-adhesive tags. Loading either type of material is easy, however the feed direction of the roll is different.
Step ➊ Open the top cover and remove the spindle from the printer. Place the spindle inside the roll of labels or tags. Cutting the corners off the end of the roll allows for easier insertion into the feed slot. If loading labels, place the roll in the top cover so that the end feeds from the top as shown in Figure 2-2.
Step ➋ Adjust the guide tabs to their widest position by pushing one or both towards the sides of the printer. Step ➌ Insert the end of the roll into the feed slot between the guide tabs until resistance is felt (approximately 3"). Figure 2-4 Open Paper Guides Figure 2-5 Feed Slot Operation 14 980008 -001 Rev.
Step ➍ While continuing to gently push the labels into the feed slot, press the FEED control to ad- vance labels until the end is visible at the front of the printer. Step ➎ Press the tension release towards the rear of the printer and center the labels in the slot.
Step ➏ Rewind the excess paper onto the roll while placing the spindle into the holder slots. Step ➐ Tap the FEED control 3 times or until the POWER indicator glows Green. If you were in the middle of printing labels, the printer will automatically resume printing.
Threading The Label Dispenser If your printer is equipped with the optional label dispenser and you would like the printer to automatically peel adhesive labels from the backing liner, follow the steps below: Step ➊ Perform steps 1-7 of the Loading Labels pro- cedure.
Step ➍ Press the FEED control to feed the leader through the dispenser. Step ➎ Push the Label Release towards the rear of the printer and pull the excess liner through the front until it is tight across the peeler bar. Step ➏ Activate the Label Taken Sensor by pushing on the top and sliding towards the front of the printer (see Figure 2-1).
AutoSense Gap Sensor Adjustment Your printer is equipped with a sensor capable of detecting the gap between labels while they are being printed. This feature depends on the ability of the sensor to “see through” the label carrier between labels.
Cleaning The Print Head As you use your printer, the print head may become dirty resulting in poor print quality. Whenever n ew label s are l oa ded i nt o the printer, the print head should be cleaned with a Cleaning Card.
Replacing the Printer Memory Backup Battery (LP+ Only) The Memory Cartridge provides storage of op- erating parameters, forms, graph ics and soft fonts. A battery in the cartridge prevents mem- ory loss if the printer power is switched off or disconnected.
Battery Replacement Step ➌ Remove the Memory Cartridge’s top cover screw with a #1 Phillips screwdriver. Slide the casing top cover off. Step ➍ Lift the battery retaining clip up and slide the old battery out. Replace the battery by lifting the battery retaining clip up and inserting the new battery in with the printed side up.
Do Not dispose of the old battery in fire. The battery may explode causing damage or injury. Dispose of the battery according to the manu- facturer’s instructions. Step ➎ Re-install the cartridge cover and insert the retaining screw. Step ➏ Re-insert the Memory Cartridge into the printer and turn the printer power on.
Operation 24 980008 -001 Rev. B.
Appendix A Troubleshooting This section addresses the most common issues user’s may face with operation and configura- tion of your printer. The first trouble shooting reference source is the Common Problems Trouble Shooting table on the following page.
Commo n Printing Problems Toruble Shoo ting Guide Problem Solution or Reason POWER indicator does not light Green when po wer s witc h is turned to “1 " (ON) position 1. Check power connections from power supply to printer and A.C. outlet. POWER indicator lights Green, but printer wil l not print.
Serial Interface Cable Wiring The figure below displays the cable wiring re- quired to use the printer’s serial interface. N/C RxD TxD DTR GND DSR RTS RI CTS Printer Host 1 1 2 2 3 3 4 4 5 5 6 6 7 7.
Removing Stuck Labels Under certain conditions, labels can become stuck inside the printer on the print head or the mechanism. This u sually occ ur s when the edges of a label pull away from the label liner. The adhesive comes in contact with the print head or the mechanism and the label peels off the liner.
Step ➊ Remove Top Cover Move the power switch to the OFF (0) position and disconnect the power and interface cables. Place the printer upside down and remove the four rubber feet by pulling them out of the mounting holes. Using a #1 Phillips screw- driver, remove the four screws that secure the top cover.
Step ➋ Remove The Print Head The most common location of stuck labels is at the print head. Check this area first before checking the remainder of the print mecha- nism.
While lifting the lower head bracket, remove the tension release rod. Without disconnecting and cables, lift and rotate the print head so that the surface can be inspected. Do not unplug the print head. The cable pro- vides ground for E.S.D. protection.
Step ➌ Install The Print Head To install the print head, first position it back over the platen. Lift the front slightly and insert the tension release rod under the metal tabs at the front edge. Lower the head down so that the ends of the rod drop into the slots on the sides of the carriage.
Step ➍ Remove Mechanism Labels can become stuck to several parts in side the print mechanism. To clear labels stuck in- side the mechanism, it must be removed from the printer base. Rem ove t he th ree screws that secure the mechanism to the base and the screw that secures the ground wire.
Step ➎ Remove Sensor Assembly Locate the push tabs on the rear of the mecha- nism. While pushing in on both tabs, pull the lower sensor assemb ly away from the mecha- nism. This provides easy access to the inside of the print mechanism. If the clear mylar label guide is damaged, it should be replaced.
Step ➏ Install Print Mechanism Replace the lower sensor assembly by sliding back into the mechanism until it locks in place. Reconnect the four connectors to the main board. Position the print mechanism on the printer base and install the three screws re- moved earlier.
Trouble shooting 36 980008 -001 Rev. B.
Appendix B Supplies and Accessories Supplies and Accessories can be ordered from ELTRON by calling: 1(800) 344-4003. Eltron gladly accepts Mastercard and Visa.
Accessor ies 38 980008 -001 Rev. B.
Appendix C Windows Printer Driver To install the Windows printer driver, use the following steps. Start your computer and then start Windows. Insert the Windows Driver disk- ette into your floppy disk drive. Double-click the Control Panel icon in the Main program group.
Using The Windows Driver The Windows printer driver provides control of several printer features when printing from Create-A-Label Professional for Windows and other Windows software applications. These features are accessed through the “Printers” control panel in the Program Manager “Main” group.
Paper Quality, Print Speed The print speed can be adjusted to compensate for manufacturing differences in label stock. Selecting a slower print speed can improve the appearance of lines and text on some label stocks.
41 Mo r e l a n d R d . Si m i V a l l e y , C A 93065-1692 ( 805) 579-1800.
デバイスThe Eltron Company LP2022の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
The Eltron Company LP2022をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはThe Eltron Company LP2022の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。The Eltron Company LP2022の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。The Eltron Company LP2022で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
The Eltron Company LP2022を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はThe Eltron Company LP2022の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、The Eltron Company LP2022に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちThe Eltron Company LP2022デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
