ThermadorメーカーPRG36の使用説明書/サービス説明書
ページ先へ移動 of 67
Thermador Professional Ranges Model s: PDR30/36/48…PRG30/36/48 The control continuously monitors sy stem parameters for co ntrol and oven failures and reports a fault code when a system problem is detected. The control utilizes the ovens blue “ on light” and oven “heating light” to report a detected fault code.
Thermador HOW TO INTERPRET CODES When a fault occurs, the control will flash the blue oven “on light” and th e Blue “heating light” sequentially to indicate the fault. The fault codes have two numbers, these numbers are interpreted by the number of times the lights flash.
ERROR CODES FOR OVENS WITH DREEFS CONTROL The following chart shows the error codes that can be displayed in the Oven/Selector window during specific oven malfunctions. Some of the error messages can be cleared by performing the following steps: 1. Turn the selector knob to OFF 2.
EMERSON APPLIANCE CONTRO LS DOCUMENT: 92S21720100 DIVISION OF EMERSON ELEC TRIC CO. REVISION: B Product Specification for Sago Ov en Control PAGE: 13. DIAGNOSTIC CODES DeBounce is the Rate at which the error checki ng occurs 13.1 Diagnostic Code Checking The following chart describ es the Fault code structure for the Contro l.
cooking cooking/timing functions F34 Upp er oven cooling fan over-speed o r under-speed detected Cooking 1 minute Message 1 Cancel cooking/timing functions F40 Upp er oven meat probe shorted Cooking 2.
F71 Lower oven meat probe not calibrated Always 10 seconds Message 1 Cancel cooking/timing functions F80 Lower oven door latch signal shorted low Always 1 minute Message 1 Cancel cooking/timing functi.
B Range Error Codes CODE DESCRIPTION WHEN CHECKED FAULT LIMIT F31 Oven temperature sensor failure Cook or clean programmed 20 sec F33 Warning Drawer Sensor Failure When W.
B Range Error Codes – Additional Information CODE DESCRIPTION WHEN CHECKED F1 Meat probe not there or incorrect During Test / use F2 Oven sensor not correct During Test / use F3 Warming sensor not correct During Test / use DOOR LATCH ERROR Door latch problem During self-clean ERROR Temp.
B WFMC Service Tips – Test Program (2B): Module Fault Codes (Test1) Test P1:ERRORS / P:01 (Viewing control module fault codes) – S tart & end test P1 (WFMC6400) / (P:01) (WFMC3200) by pushing Start/Pause button. Scroll through list of fault codes by pushing Spin Selection (WFMC3200) or Menu (WFMC6400) buttons.
B WFMC Service Tips – Test Program (2C): Motor Control Fault Codes (Test1) Test P1:ERRORS / P:01 (Viewing motor control fault codes) – Start & end test P1 by pushing Start/Pause button. Scroll through list of (18) fault codes by pushing Spin Selection (WFMC3200) or Menu (WFMC6400) buttons.
B WTMC Service Tips - - Test program (4A): Fault Codes WTMC Dryer Test Program Fault Codes Fault Code Fault Solution Notes Effect E:11 Overheating due to clogged lint filter. Clean lint filter (&air duct if necessary). Displays E:01 during normal use.
B WTMC Service Tips - - Test program (4B): Fault Codes WTMC Dryer Test Program Fault Codes Fault Code Fault Solution Notes Effect E:23 Model variant doesn’t match table Replace faulty control module. Dryer stops & can’t be restarted. E:24 Software version doesn’t match table Replace faulty control module.
B Service Tips – Fault Codes (1) DISHWASHER TEST PROGRAM ERROR COD ES (on 2&3-digit digital displays): 0- No faults 1- Aqua Sensor (Sensotronic) fault 2- Heating system fault (heater.
B Service Tips – Fault Codes (2) Fa u l t s 3 - N T C 4 - Aqu a se n sor LE D F a ul t Co d e s 0 - N o fa u l ts 1 - Heat er E l em en t 2 - W a t e r F illing NS F NS F NS F NS F CY CLE CL E AN NS.
B Thermador BSH HOME APPLIANCES CORPORATION ERROR CODES For products with electronic controls.
B.
Thermador ® 1 Ther mador Professional Ranges Models : PDR30/36/48…PRG30/36/48 The control continuously m onitors system param eters for control a nd ov en failures and re ports a fault code when a sy stem problem is detect ed. The control ut ilizes the ov ens blue “on light” and ov en “heating light ” to report a detected f ault code.
Thermador ® C, CM and CJ Oven Error Code Messages – Updated 2/21/02 Error Code Displayed Probable Cause Example Corrective Action “F10” Power Board Incompatibility. Power/Relay Board. Check all connection s betwee n the power/relay board and the Control display PCB.
Thermador ® C, CM and CJ Oven Erro r Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action “F19” Miscellaneous Power/Relay Board Error. Power/Relay Board. Check all connections between the power/relay board and the Control display PCB.
Thermador ® C, CM and CJ Oven Erro r Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action “F25” Multiple To uch Input Keys Stuck. Control Display PCB Or Touch Panel. Check all connections between the control d isplay PCB and the touch panel.
Thermador ® C, CM and CJ Oven Erro r Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action “F34” Upper Oven Cooling Fan Air Switch Not Detected. 1. Air Switch. 2. Cooling Fan. 3. An Open Circuit In The Upper Oven Air Switch Wiring.
Thermador ® C, CM and CJ Oven Erro r Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action “F52” Upper Oven Door Position Error (Locked & Open). Defective Or Jammed Upper Oven Door Or Latch Switches. Check Header P9 and P0 on the power/relay board and P11 on both power/relay board and control display PCB.
Thermador ® C, CM and CJ Oven Erro r Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action “F61” Lower Oven Sensor Open. Oven Sensor Wiring. An Open Circuit In The Lower Check all connections. Check resistance of lower oven sensor (approximately 1080 ohms at room temperature).
Thermador ® C, CM and CJ Oven Erro r Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action “F80” Lower Door Signal Shorted Low. Defective or jammed lower oven door or latch switches. Check header P5 on the power/relay board and P11 on both power/relay board and contro l display PCB.
Thermador ® C, CM and CJ Oven Error Code Messages…continued Note 2 Oven sensor should measure 1050 ohms at 75 degrees F. If the sensor measures correctly (within 10%) check each leg of the sensor to ground and to each phase of the electrical supply.
Thermador ® CT and CMT Ovens with Dr eefs Control Error Codes Error Codes E1 Causes Control bd Example Disables clean in both ovens, allow cooking Corrective Action Replace control board E2 Sensor or.
Thermador ® CT and CMT Ovens with Dreefs Control Error Codes…continued Error Codes E8 Causes Control bd Example Remains in display oven unusable Corrective Action Replace control bd E9 Latch Latch motor may run but switches do not cycle Replace latch in affected oven.
Thermador ® S, SM, AND SMW Oven Error Code Messages – Updated 02/21/02 Error Code Displayed Probable Cause Example Corrective Action F1 Element Supervisor Enabled Main power/relay board Replace mai.
Thermador ® S, SM, AND SMW Oven Error Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action F4 Shorted Oven Sensor Or Temperature At Sensor Below 40 Degrees F. Short In Oven Sensor Wiring Check Oven Sensor Wiring. Should read 1050 ohms when measured from molex plug on main power/relay board at room temperature.
Thermador ® S, SM, AND SMW Oven Error Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action F8 Shorted meat probe (No probe is used on these models) Main power/relay.
Thermador ® S, SM, AND SMW Oven Error Code Messages…continued Error Code Displayed Probable Cause Example Corrective Action F- Communication error detected by main power/relay board. Control head Check all connections between both power/relay boards.
Thermador ® S, SM, AND SMW Oven Error Code Messages…continued Note 1 F1, F7 Errors are caused by a single loss of communication between the control head and the touch panel.
Thermador ® S, SM, AND SMW Oven Error Code Messages…continued Note 4 The touch panel is an electronic switching device so it does not have actual keys that stick. The control head was designed for use with either membrane switches or electronic inputs.
Thermador ® RDF, REF 30 inch Range error codes Error Codes F1 Causes Stuck buttons Stuck latch switch Example Button is jammed Lock & unlock switches Corrective Action Unstuck buttons Replace lat.
Thermador ® Thermador ESC30 and GSC30 30 inch range error codes Error Codes F1 Causes Supervisory relay enable shorted Example Bake or broil relay stuck closed Corrective Action Cancel key will clear error if fault re mains it will appear again in 16 seconds.
Thermador ® Thermador ESC30 and GSC30 30 inch range error codes Error Codes F6 Causes Missing APPLIANCE CHASSIS line cycle detector Example If 60 cycles is missing for one minute Corrective Action Cancel key will reset F7 Function key stuck or shorted Stuck key Must power down to clea r this error.
Thermador ® Error codes for Gaggenau St eam Oven model ED-220/221 Error Code Cause Exam ple Corrective Action F10 Oven sensor open Open circuit Check sensor See note 1 F11 Oven sensor shorted Pinched wire Check sensor See note 1 F12 Probe open Open circuit Check probe See note 2 F13 Probe shorted Pinched wire Check probe See note 2 F14 Relay bd.
Thermador ® Error codes for Gaggenau St eam Oven model ED-220/221 Error Code Cause Exam ple Corrective Action F30 EEPROM not programmable F61 Too much water or not enough heat during calibration run Will not go into diagnostic mode will not complete calibration and will cancel Replace the display board.
Thermador ® Error codes for Gaggen au Steam Oven model ED-220/221…continued Error Code Cause Exam ple Corrective Action F72 Base pan sensor Defective electronics Replace relay board F73 Main water .
Thermador ® Gaggenau EB 270/271/290/ 291 Oven Error Codes Error Code Cause Exam ple Corrective Action F10 Open oven sensor Open circuit Check sensor See note 1 F11 Shorted oven sensor Pinched wire Ch.
Thermador ® Gaggenau EB 270/271/290/ 291 Oven Error Codes Error Code Cause Exam ple Corrective Action F30 EEPROM error Replace display bd. See note 5 F40 Latch error Wiring, motor, microswitch Check .
Thermador ® Gaggenau EB 270/271/290/291 Ov en Error Codes...continued Note 1 Oven sensors should measure 1050 ohms at 75 degrees F. if the sensor measures correctly (within 10%), check each leg of the sensor to ground and to each phase of the electrical supply.
GAGGENAU Steamer VK 230 27 F 6 Steam sensor faulty insta lled (only possible during factory or universal comparison!) 8 FUNCTION CODES Faults at the appliance, a correc t or incorrect adjustment as well as the RESET-function are indi cated / confirmed by signals or error codes.
B HBL/HBN 7 FAULT CODE DEFINITIONS AND BASIC TROUBLESHOOTING HINT: After a latch fault, due to any hardware problem, the contr ol can disable one cavity and prevent the opposite one to work in self-clean.
B Error Cause Corrective Action F31 Upper (or single) oven temperature sensor failure. An open or short circuit in the sensor wiring. 1. Check all connections, especi ally P4 on the Power Board. 2. Unplug the sensor connector and check sensor resistance (approximately 1080 ohms at room tem perature with connector removed).
B Error Cause Corrective Action F32 Lower oven temperature sensor failure. An open or short circuit in the lower oven sensor wiring. 1. Check all connections, especi ally P24 on the Power Board. 2. Unplug the sensor connector and check sensor resistance (approximately 1080 ohms at room tem perature with connector removed).
B Error Cause Corrective Action F42 Lower motorized latch will not lock. Defective or jammed lower oven door or la tch switches. Defective latch motor or its wiring. 1. Check P24 connector on the Power Board. 2. Ensure door latch switc hes are operating properly.
B Error Cause Corrective Action F44 Lower motorized latch will not unlock. Defective or jammed lower oven door or la tch switches. Defective latch motor or its wiring. 1. Check P24 connector on the Power Board. 2. Ensure door latch switc hes are operating properly.
B Error Cause Corrective Action F46 Lower oven latch both locked and unlocked. Defective or jammed lower oven door or la tch switches. 1. Check P24 connector on the Power Board. 2. Ensure door latch switc hes are operating properly. 3. Check that neither latch switc h nor common wires are pinched to the appliance chassis.
B Error Cause Corrective Action F112 Runaway lower temperature (>650°F). a) Oven powered on when temperature inside oven is >650°F. b) Intermittent or bad temperature sensor. c) Heating element relay stuck on. 1. Allow oven to cool down <650°F before turning power on.
B Error Cause Corrective Action F114 Runaway lower temperature (>950°F) a) Intermittent or bad temperature sensor. b) Heating element relay stuck on. 1. Check P24 connector on the Power Board. 2. Unplug the sensor connector a nd check lower sens or resistance (approximately 1080 ohms at room tem perature with connector removed).
B Error Cause Corrective Action F125 [Upper Cancel] or [Cancel] for single oven key circuit problem. Bad connection or bad Display or keyboard. 1. Check all connections betw een keyboard (J1) and Display Board (P5). 2. If OK, replace keyboard or Display Board or both.
B Error Cause Corrective Action F143 Vcc open circuit on slave micro. Bad Power Board or Display Board. 1. Check power display and Display Board connectors P1B associated wiring. 2. If OK, replace Power Board. 3. If fault persists, replace Display Board.
B Error Cause Corrective Action F153 Control calibration values not in range. Bad Power Board or Display Board. 1. (If possible, re-calibrate.) 2. Check power and Display Boar d connectors P1B and associated wiring. 4. If OK, replace Power Board. 5. If fault persists, replace Display Board.
B FAULTS NOT DETECTED BY THE CONTROL Problem Possible Solutions Meat probe icon appears on the display even if the probe is not plugged in. 1. Check P2 connector on the Display Board and the wires. 2. Check the connection terminals on the socket m ounted on the cavity left sidewall.
B Problem Possible Solutions Oven lights always off 1. Check P11 connector on the Display Board and the wires. 2. Check the transformer. 3. Check that the lamps are not burnt. 4. If OK, replace Power Board. Cavity fan doesn’t work or it works at one speed only.
B Problem Possible Solutions One of the elements is not energized. 1. Check all connections between th e relays on the Power Board and the elements. 2. Check the relay outputs on the Power Board. All the elements are not energized. 1. Check the common L1 red wi re on the Power Board relays.
B WFR 2460 Washer Fault Codes T1: Error (error displays). The last 8 fault codes are stored & displayed! Er: 08 Heating time exceeded After 105 min. Start T/P18 heater test programm e Er: 09 Uncontrolled motor acceleration Motor triac defective Start T/P4 motor test programm e.
B WFK 2401 Washer Fault Codes Fault Code Faults Possible Causes/Notes Corrective Actions 00 No Faults 01 No Water filling • Water supply turned off. • Water inlet hose filters (stra iners) blocked. • Water pressure too low. • Control module has failed.
B WFK 2401 Washer Fault Codes Fault Code Faults Possible Causes/Notes Corrective Actions 05 Drum motor erratic • Motor drive circuit (Triac) has failed. • Drum drive motor has failed. • Reserving relays have failed. NOTE: Fault code occurs during test program.
B WFK 2401 Washer Fault Codes Fault Code Faults Possible Causes/Notes Corrective Actions 09 NTC failed • NTC open circuited. NOTE: Fault code occurs during test program. • Disconnect NTC and measure resi stance at terminals (~5.4 – 6.5 k Ω @ 20°C (68°F)).
B WFL 2060 Washer Fault Codes Fault Possible Causes Flashing Lights Program fault Occurred Door open or won’t lock Door left open. Faulty door latch or door lock ○ Door locked ○ Rinse/Spin ● Wash Wash No water filling Water shut off.
B 47 WTA 35 & WTL 54 Fault Codes & Troubleshooting HINT : Use dryer test program to diagnose dryer problems. HINT : Remove top panel of dryer to access wi ring, control module and drum conductance brushes.
B 48 WTA 35 & WTL 54 Fault Codes & Troubleshooting Anti – Crease/End Light flashes Time fault (drying time too long) Control module failed. Door lock failed. Moisture sensor(s) failed. Water level switch failed (WTL 5400 only).
B B Dishwasher Error codes Error codes that the consumer will s ee on models with numeric display: F Indicates a water level or filing error. Underfill, overfill o r water in the base. See note 1 2H Indicates that the last wash cycl e took over 99 minutes to complete.
B B Dishwasher Error Codes…continued NOTE 1 Once cause of this fault has be en corrected, the code will re set itself 15 minutes after The dishwasher has been turned on, or by running the dishwasher through the diagnostic program. See B/S/H Dishwasher Troubleshooting Tips, or Major Appliances T echnical Manual for instruction by model number.
B 51.
デバイスThermador PRG36の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Thermador PRG36をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはThermador PRG36の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Thermador PRG36の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Thermador PRG36で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Thermador PRG36を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はThermador PRG36の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Thermador PRG36に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちThermador PRG36デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
