Thermo ProductsメーカーMO-425の使用説明書/サービス説明書
ページ先へ移動 of 20
MO-425 ECN 4392- MA OIL FURNACE GENERAL SERVICE AND MAINTENANCE MANUAL FOR USE WITH THERMO PRIDE OIL FURNACES THERMO PRODUCT S, LLC . PO BOX 217 NORTH JUDSO N, IN 46366 PHONE: (574) 896-2133.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. i TABLE OF C ONTENTS SECTION BEGINNING P AGE I . GENERAL I NSTRUCTI ONS 1 I I . I N S T A L L A T I O N 2 A. CHI MNEY 2 1. PROPER CHI MNEY SI ZE 2 2. PREVENTION OF CHI MNEY CONDENSING 3 3.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 1 I. GENERAL INSTRUCTIONS - READ BEFORE START OF INSTALL ATION 1.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 2 If the " entir e" build ing is unusually tight ly construc ted a nd/or has an exha ust fan insta lled, a low pr essure z one co uld b e cre ated w ithin th e structu re.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 3 2. PREVENTION OF CHIM NEY CONDENSING: Stack gas m ay do one of tw o things as it escapes u p the chim ney : A. Rem ain en tirely in a gaseous state if the in ternal chim ney w all tem perature is above th e dew poin t, or B.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 4 3. PROPER CHIM NEY HEIGHT: The chimney shall ter minate a t lea st 3 fee t abo ve the highe st po int where it p asses thro ugh the ro of of a build ing and a t least 2 feet hig her than any portion of a bu ilding w ith in a horizontal dis tance of 10 feet.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 5 5. PRO PER CHIM NEY BOTTO M LEVEL: In cases w here the chim ney extends to the basem ent floor, the draft can us.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 6 Fig. 7: Alternate constructions that allow reduced clearances to com bustible materials.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 7 The vent conn ector pipe between the f urnace an d chim ney shall be of equal diam eter as the flue outlet of th e furnace. The vent connector pipe m ust be m ade of 24 gauge (or thicker) corrosion-resistant steel.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 8 Fig. 8: Supply air duct sizing Example The RETURN AIR DUCT SYSTEM should eq ual the w arm air duct sy stem in airflow capabilities.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 9 D. OIL TANK & PIPING: ? ? ? ? WARNING: All local codes and ordinances take precedence wi th regard to tank and oil lines.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 10 Below th e w iring diag rams for the variou s T herm o Pride oil furnace m odels.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 11 G. INITIAL BURNER OPERATION: IMPORTANT: READ B URNER INSTRUCTION MANUAL (INCLUDED WITH BURNER) BEFORE CONTINUING. To successfully service an d initially set up the oil furnace, y ou must use th e follo w ing instru men ts: A.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 12 For exam ple, if a 13% CO 2 (3.5% O 2 ) is measu red at a trace of smoke, open the air sh utter until a zero sm oke reading is obtained w ith a 12% C O 2 or 4.5% O 2 .
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 13 TURN T'STAT SE TTING ABOVE ROO M TEMPERATURE TURN THERMOSTAT TO CALL FOR HEA T DOES TH ERMOSTAT MAKE CON TA.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 14 POSITI ON THEM PER BURNER MANUFACTURERS INSTRUCTIONS REPLACE IG NITI ON TRANSFORM ER ARE THE ELECTRODES ARCING? .
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 15 PROPER COMBUST ION ACHIEVED? IS THE PROBLEM DELAYED IGNITION? IS PUMP PRESSURE SET ACCORDING TO BURNER APPLICATI.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 16 GO TO PROPER COMBUST ION ACHIEVED SECTI ON ABOVE AND SET COMBUSTION ADJUST BLOWER SPEED TO RAISE TEM PERATURE RISE. -- INCREASE L ENGTH OF BURNER ON CYCLE -- INSULATE CHIM ENY W ITH CHIMNEY LINER.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 17 B. CAD CELL CHECK OUT PROCEDURE: 1. Remove cad cell lead w ires, then start th e burner. Shortly after burner st arts, place a tem porary jum per between term inal f - f.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 18 ? ? ? ? CAUTION: Do not attempt to start burn er when: 1.Ex cess oil has accumulated 2.W hen the furnace or burner is full of vapor 3.W hen the combustion chamber is very hot.
デバイスThermo Products MO-425の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Thermo Products MO-425をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはThermo Products MO-425の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Thermo Products MO-425の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Thermo Products MO-425で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Thermo Products MO-425を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はThermo Products MO-425の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Thermo Products MO-425に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちThermo Products MO-425デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。