Tiger Products Co., LtdメーカーNH TS100-135Aの使用説明書/サービス説明書
ページ先へ移動 of 20
PAGE - 1 INSTRUCTIONS SWEEPER ASSEMBLIES NH TS100-135A 06020012 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.
PAGE - 2 FORWARD 2 TABLE OF CONTENTS 2 SAFETY PERCAUTIONS 3 OPERATIONAL SAFETY PRECAUTIONS 4 OPERATION 5 IMPORTANT INSTRUCTIONS 7 MOUNTING INSTRUCTIONS 8 LEVELING INSTRUCTIONS 10 SUPPORT YOKE ADJUSTME.
PAGE - 3 This symbol means: CAUTION ! Your safety is at rick ! – Any R.O.P.S. (roll over protective structure) should not be drilled, welded on, or altered in any manner. Any alteration may reduce your protection. – Do not bypass the tractor neutral safety swith.
PAGE - 4 OPERATIONAL SAFETY PRECAUTIONS This symbol means: CAUTION ! Your safety is at rick ! – Reduce speed when turning, taking curves, rough ground, or hillsides to reduce chance of rollover. – Always keep tractor in gear when traveling downhill to prevent runaway.
PAGE - 5 OPERATION Be sure the ball valves on the mower hydraulic tank are OPEN before starting the tractor. Serious damage to the hydraulic system can occur if the valves are not OPEN. For brush operation: open the high pressure valve located near the pressure port of the pump and close the high pressure valve located near the electrical solenoid.
PAGE - 6 It is very possible to cut brush life by 50% if the frame is not level. Running an unlevel brush is jast like throwingmoney out the window. The small amount of time spent leveling a brush before sweeping is paed back many times over in longer brush life.
PAGE - 7 1. Do not store sweeper polypropylene brushes in direct sunlight! Direct sunlight will cause the bristles to deteriorate, causing the bristles to become brittle. If the broom is to be stored for any length of time, store it in the shade, inside, or cover the brush with a tarp to protect it from the sun.
PAGE - 8 MOUNTING INSTRUCTIONS Please rea and understand the instructions and schematics completely before beginning assembly. Parts and drawings may vary slightly due to the variety of tractor makes and models. The mounting kit you receive should be correct for your application.
PAGE - 9 11. The spring - chain assemblies are used to help support the weight of the brush head assembly when in the sweeping position. Hook on spring to each of the outside holes in the top plate of the brushhead upright. The chains are con nected to the outside slots in the chain holder on the spring - chain assembly.
PAGE - 10 LEVELING INSTRUCTIONS The sweeper must be leveled t maintain even brush wear and to produce efficient sweeping action. If the broom is not leveled at first and periodically after that, then it will put stress on certain parts causing excessive wear.
PAGE - 11 Make a note of the measurements. Swing the brush head assembly to the left and take the same measurements. If the measurements are not equal, refer to previous leveling steps and illustrations for adjustments. LEVELING INSTRUCTIONS CONTINUED 5.
PAGE - 12 SUPPORT YOKE ADJUSTMENT NOTE: This section applies only to units with serial number 75146 and above. Units with serial number below 75146 do not have adjustable support yokes. Before operating the sweeper the brush head frame support yokes should be checked and if necessary adjusted as follows: 1.
PAGE - 13 BRUSH REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place.
PAGE - 14 MOTOR AND HUB REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place.
PAGE - 15.
PAGE - 16 TRACTOR MOUNT - MAIN FRAME.
PAGE - 17 TRACTOR MOUNT - MAIN FRAME ITEM PART NO. QTY. DESCRIPTION 1 34857 1 MTG,THS 2 06410443 1 MNT,LH,SWPR,CNH,TSA 2 06410442 1 MNT,RH,SWPR,CNH,TSA 4 06430049 4 SPACER,2.00x1.00x3.34 5 41644 1 PLATE,ATTACHING 6 21735 4 CAPSCREW,1/2 x 2 1/2,NC 7 24879 4 CAPSCREW , 20MM x 65MM(2.
PAGE - 18.
PAGE - 19.
PAGE - 20.
デバイスTiger Products Co., Ltd NH TS100-135Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Tiger Products Co., Ltd NH TS100-135Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTiger Products Co., Ltd NH TS100-135Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tiger Products Co., Ltd NH TS100-135Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tiger Products Co., Ltd NH TS100-135Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tiger Products Co., Ltd NH TS100-135Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTiger Products Co., Ltd NH TS100-135Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tiger Products Co., Ltd NH TS100-135Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTiger Products Co., Ltd NH TS100-135Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
