ToaメーカーC-CV454D-9 CUの使用説明書/サービス説明書
ページ先へ移動 of 20
Thank you for purchasing TOA Outdoor Day/Night camera: Wide, Standard, or Tele. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 5 3. HANDLING PRECAUTIONS .
3 1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.
4 • Leave the installation of the unit to your TOA dealer because the installation requires expert experience and skills. The unit may fall off if incorrectly installed, resulting in possible personal injury.
5 2. GENERAL DESCRIPTION The TOA C-CV454 series are outdoor Day/Night cameras equipped with a 1/3" CCD. A lineup of cameras with three types of lenses, Wide, Standard, and Tele allows accurate monitoring over a wide range from near to distant subjects depending on the installation location.
6 ( 1 ) Vari-focal lens ( 2 ) Sunshade ( 3 ) Front cover ( 4 ) Mounting bracket (accessory) ( 5 ) Safety wire mounting hole ( 6 ) Sunshade fixing screw ( 7 ) Bracket mounting bolt (accessory) ( 8 ) Mo.
7 [Ceiling mounting example] [Wall mounting example] Bracket mounting bolt with washer , stainless steel (accessory) Camera mounting bolt M8 or W3/8 Safety wire mounting hole Note Install a safety wire as needed. Select the wire considering its length, diameter, and hook strength.
8 Camera mounting bolt M8 or W3/8 Camera mounting bolt M8 or W3/8 [Example 3: Mounting to a ceiling or wall] If only fine adjustment of camera angle is required; [Example 2: Mounting on a wall] If ang.
9 3. Install the camera unit to the mounting bracket using the supplied insulating spacers and Bracket mounting bolts (with washer, stainless steel). Note Be sure to position the insulating spacers between the bracket and bolt, as induction voltage or noise may be produced at the joints depending on installation conditions.
10 Fit the waterproof cap (shaded area) into place. 5. Attach the waterproof cap to the camera unit. Note If the waterproof cap is not secured to the mounting surface, water or moisture soaks in, causing the corrosion of the BNC connector. This may cause unit failure.
11 6. Connect the camera unit. Connect the camera unit to both the monitor and the power supply as illustrated below. Notes • If the Video output is not terminated at 75 Ω , camera images are not properly displayed. Make sure that the output has been terminated at 75 Ω at the connected monitor or switcher.
12 Loosen two sunshade fixing screws. T urn the sunshade, then extract it. 2. Connect the camera’s monitor output terminal to the monitor. Note: The camera will not operate if the monitor output terminal is connected to the camera drive unit. 3. Switch on the power supply.
13 Angle of view: ± 90° (T urn the Camera head) Projection Bracket mounting bolts Horizontal angle: ± 60° Camera mounting bolt V ertical angle: 90° (For the ceiling installation) Focus ring Zoom ring Mode setting switch Iris control The C-CV454D18 differ in positions of the focus ring and zoom ring; their positions are exchanged.
14 Sunshade fixing screw (Screw with captive washer M3x8) Slot to insert the sunshade fixing screw Sunshade Sunshade fixing screw After inserting the sunshade, turn clockwise to fix it in position (as shown), then secure it with the sunshade fixing screws.
15 Mode Setting Switch (Factory-preset setting) 1: Focus adjustment switch 2: Backlight compensation switch 3: Flickerless switch 4: A TW/AWB selection switch 5: Mode selection switch ATW D / N AWB COLOR F. A D J BLC 1/100 1/60 ON OFF ATW D / N AWB COLOR F.
16 ON OFF ON OFF ON OFF ON OFF 7.4. ATW/AWB selection switch: Set the white balance operation. ATW: Set to “OFF” position during normal use. The camera's white balance automatically changes as an object's color temperature varies. AWB: Set to “ON” when the difference between the displayed color and actual color is annoying.
17 Remedy Connect the cables correctly. Solder BNC plugs correctly. Focus the lens. Remove dirt on the lens. Adjust the level correctly in accordance with the instruction manual of the monitor. Focus the lens again after turning the Focus adjustment switch of the Mode setting switch to “ON” position.
18 9. SPECIFICA TIONS C-CV454D-3 (CU) C-CV454D-9 (CU) C-CV454D18 (CU) 24 V AC, 50/60 Hz or 12 V DC 4 W (300 mA, Maximum current: 800 mA) 1/3 type IT-CCD 771 (H) x 492 (V), 380,000 pixels 2:1 interlace Horizontal: 15.734 kHz, Vertical: 59.94 Hz VBS1.0 V(p-p), 75 Ω , RCA pin jack VBS1.
19 • Accessories Mounting bracket ..................................................................................... 1 Cable with waterproof cap (2 m) .............................................................. 1 Bracket mounting bolts (with washer, stainless steel) .
133-22-161-10 URL: http://www.toa.jp/.
デバイスToa C-CV454D-9 CUの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Toa C-CV454D-9 CUをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToa C-CV454D-9 CUの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toa C-CV454D-9 CUの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toa C-CV454D-9 CUで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toa C-CV454D-9 CUを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToa C-CV454D-9 CUの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toa C-CV454D-9 CUに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToa C-CV454D-9 CUデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。