TOA ElectronicsメーカーC-CC714 NTの使用説明書/サービス説明書
ページ先へ移動 of 32
Thank you for purchasing TOA’s Outdoor Combination Camera. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 5 3. FEA TURES ..........
3 1. SAFETY PRECAUTIONS • Be sure to read the instructions in this section carefully before use. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.
4 When Installing the Unit • Avoid installing the unit in locations exposed to sea breeze or corrosive gas. Mounts may become corroded, eventually causing the unit to fall off, which could result in personal injury. • Do not mount the unit in locations exposed to constant vibration.
5 2. GENERAL DESCRIPTION TOA’s dome-type color cameras combine with a high-speed camera drive that permits one 360-degree horizontal rotation per second and a 22 times (C-CC714) or a 23 times (C-CC764) optical zoom lens. Up to 255 arbitrary positions can be preset and such preset positions can be instantaneously repeated.
6 4. HANDLING PRECAUTIONS • Noise may appear on the monitor or preset camera positions may deviate with prolonged camera use. In such cases, use the camera’s refresh function to automatically refresh settings and reestablish the home position once a day or week, thus allowing any position deviation to be corrected.
7 • The dome camera features built-in heat generating circuitry. Take care not to touch the internal parts marked “Caution! High Temperature” when working inside the camera during dome cleaning or maintenance .
8 1 2 3 4 5 6 [ Housing Appearance ] 13 14 15 16 18 19 17 20 19 10 12 9 9 9 9 11 11 7 8 9 9 [ Housing Bottom ] [ Camera Unit Top ] [ Camera Unit Bottom ] 5.
(1) Top cover (2) Safety wire for housing (3) Housing adaptor (4) Safety screw (5) Dome cover (6) Decorative frame (7) Sunshade (Outside) (8) Case (Inside) (9) Hexagon sleeve (10) Safety wire for dome.
10 6.1. Precautions When Installing the Camera • Insulate the joint of the camera video output cable and the coaxial cable from other equipment by wrapping the (vinyl) insulating tape around it. Also, install such cables taking care that they do not contact metal stuff close to them.
11 GND GND Connect to the next cameraʼs terminal Camera control cable Camera control cable Shield twisted pair cable Connect to remote controller ʼs camera control terminal 6.
7.3.1. Camera Address Setting Switch (DIP Switch 1: No. 1 – 8) Used to set camera address when using the camera in connection with the C-RM500 Remote Controller. Set the DIP switch so that the address is equal to the connected switcher's channel number.
13 7.3.5. Termination Switch (DIP switch 2: No. 8) Set the switch of the camera last connected to the RS-485 communications line to ON. (Factory setting: OFF) 7.3.2. Communication Speed Setting Switch (DIP switch 2: No. 1 – 2) Check to be sure that the communication speed set here is the same as that of the Remote Controller.
14 ON 12345678 11 7 3 3 4 9 ON 12345678 ON 12345678 ON 12345678 ON 12345678 21 8 3 4 5 0 ON 12345678 ON 12345678 ON 12345678 ON 12345678 31 9 3 5 5 1 ON 12345678 ON 12345678 ON 12345678 ON 12345678 42.
15 ON 12345678 65 81 97 1 13 ON 12345678 ON 12345678 ON 12345678 ON 12345678 66 82 98 1 14 ON 12345678 ON 12345678 ON 12345678 ON 12345678 67 83 99 1 15 ON 12345678 ON 12345678 ON 12345678 ON 12345678.
16 ON 12345678 129 145 161 177 ON 12345678 ON 12345678 ON 12345678 ON 12345678 130 146 162 178 ON 12345678 ON 12345678 ON 12345678 ON 12345678 131 147 163 179 ON 12345678 ON 12345678 ON 12345678 ON 12.
17 ON 12345678 193 209 225 241 ON 12345678 ON 12345678 ON 12345678 ON 12345678 194 210 226 242 ON 12345678 ON 12345678 ON 12345678 ON 12345678 195 21 1 227 243 ON 12345678 ON 12345678 ON 12345678 ON 1.
18 8.1. About Installation • Mount the camera to a heavy-duty wall surface using the optional C-BC711W Wall Mounting Bracket. • When installing the camera on a pole, use the optional C-BC711W Wall Mounting Bracket, C-BC711PM Pole Mounting Bracket and 2 YS-60B Mounting Bands in combination.
19 8.3. W all Mounting Bracket Installation Use the optional C-BC711W Wall Mounting Bracket. Notes • Check to be sure that wall surface can structurally support the weight of the camera and mounting bracket • Bolts, nuts and washers are not supplied with the bracket.
20 8.4. Attaching Housing and Camera Unit to W all Mounting Bracket 1. Loosen 2 safety screws. 2. Run the safety wire through the top cover, then hang the hook to the mounting bracket.
21 5. Using the 3 supplied camera mounting screws M5 x 12, attach the housing unit to pipe. Tighten 3 screws equally and ensure that no parts rattle. Note: In this event, tighten screws while pressing the housing against the pipe. 4. After confirming the housing direction, push the housing up, then tighten 2 safety screws.
22 7. Connect the safety wire to the housing projection, then attach the camera unit. Note: Align mark of the camera unit with that of the housing when attaching the camera unit to the housing. Hang the safety wire. Safety wire mark 6. Using the supplied 3 hexagon socket screws, attach the top cover 1 to the housing.
23 8. Make the camera unit in horizontal position and push it straight up closely to the housing. Cross sectional view of the housing Camera unit 1 2 mark Duct Note Insert the camera unit in an oblique direction in the order of 1 to 2 keeping away from the duct of the housing.
24 Safety wire protrudes from the compartment. Safety wire does not protrude from the compartment. Note When mounting the camera unit to the housing, mount it straight till it is attached to the housing correctly. Mounting it at an angle may cause damage to the camera unit.
25 10. Tighten 2 camera unit mounting screws to attach the camera unit to the base unit. Camera unit mounting screw Camera unit mounting screw 11. Attach the dome cover. Slide down the dome cover’s screw head through the housing suspension fitting’s slot.
26 13. Tighten 4 screws equally to attach the dome cover to the housing and ensure that the dome cover does not rattle. 12. Align the dome cover’s 4 screws with the hexagon head sleeves inside the housing.
27 8.5. Pole Mounting Bracket Installation The optional C-BC711PM Pole Mounting Bracket, C-BC711W Wall Mounting Bracket and YS-60B Mounting Band are required to mount the camera on a pole. Note Those mounting brackets and band can be installed on a pole having a mounting pipe diameter of 90 - 340 mm.
28 8.6. Suspension Bracket Installation The C-BC711P Suspension Bracket is required to suspend the camera from a ceiling. Note Mount the bracket to a concrete wall or robustly constructed wall surface that can sufficiently withstand the weight of the units.
29 [ RS-485 Communications line control ] Combination camera Multi-switcher Monitor TV Outdoor combination camera Dedicated Remote controller Note Combination cameras and outdoor combination cameras can be used in free combinations.
30 C-CC764 NT C-CC764 PL 24 V AC, 50/ 60 Hz (2P loose end) 10 W (normal operation), 80 W max. RS-485 communications system (new protocol compatible) VBS 1.
31 C-CC714 NT C-CC714 PL 24 V AC, 50/ 60 Hz (2P loose end) 10 W (normal operation), 80 W max. RS-485 communications system (new protocol compatible) VBS 1.
• Accessories CD-R (CAMARA CONTROLLER Software, installation manual) ...... 1 Hexagon socket screw M4 x 8 ...........................................
デバイスTOA Electronics C-CC714 NTの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
TOA Electronics C-CC714 NTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTOA Electronics C-CC714 NTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TOA Electronics C-CC714 NTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TOA Electronics C-CC714 NTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TOA Electronics C-CC714 NTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTOA Electronics C-CC714 NTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TOA Electronics C-CC714 NTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTOA Electronics C-CC714 NTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。