TOA ElectronicsメーカーF-122CU2の使用説明書/サービス説明書
ページ先へ移動 of 16
INSTRUCTION MANUAL CEILING SPEAKER SYSTEM F-122CU2 Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 3 3. FEA TURES ..........
3 • Leave the installation to your TOA dealer because the installation requires expert knowledge. Improper installation may cause the unit to fall, resulting in personal injury and/or property damage. • Install the unit in a location that can structurally support the weight of the unit and its mounting hardware.
4 3. FEA TURES • Bass-reflex speaker system designed to provide a wide frequency range and high power handling capability. • Wide-dispersion flush-mount ceiling speaker design employs unique acoustic construction to realize a wide area of coverage.
Before mounting the speaker, check the ceiling structure is of drop ceiling with 2-foot standard ceiling tiles. 5 5. MOUNTING HARDW ARE INST ALLA TION [Installation view on Drop Ceilings] Caution Set the tile bridge so that both ends fit securely into the T-grids, even if the ceiling tile accidentally falls off.
6 Step 3. Attach a safety wire to prevent the speaker from accidentally falling. To attach, tie one end of the supplied safety wire around the speaker's safety wire hook, and tie its snap ring around a secure C-channel bar or suspension pipe.
7 6. WIRING 6.1. Using the Speaker in UL1480 Category UUMW Choke bracket Cover plate Cover plate Connector cover After completing the speaker cable connection, turn the connector cover in the direction indicated by the arrow , and fix the cover with 2 screws.
8 6.2. Using the Speaker in UL1480 Category UEA Y and CAN/CSA C22.2 No.205 Category UEA Y7 6.2.1. Wiring through hard or flexible conduit Note The choke bracket equipped with the speaker has not been evaluated by UL, for conduit connection and UL514B Standard.
9 6.2.2. Wiring with naked cables Loosen the screw to allow the speaker cable to pass through. Choke bracket Retighten the screw to fix the speaker cable.
10 Step 2. Detach the removable input connector from the speaker's socket, and loosen the screw of the terminal to be used. Speaker unit Removable input connector Step 3. Insert the stripped cable end into the terminal and tighten the terminal screw with a screwdriver.
11 Caution Before mounting, check to be sure that the speaker's 3 mounting tabs are turned inside the unit as shown in the figure. If turned outward, the speaker cannot be inserted through the mounting hole. In Out Mounting tab Step 1. Insert the speaker through the mounting hole till it contacts the ceiling panel.
12 Step 3. Set the input power. Turn the input selector switch (on the unit's front) to set it to the desired input impedance. (Factory-preset to 170 Ω .) Note Setting positions "8 Ω " and "16 Ω " can be used in UL1480 Category UEAY and CAN/CSA C22.
13 Mounting tab axis screw Use an electric screwdriver to detach. Mounting tab Screw cap Caution Be sure to set the screwdriver's torque for under 4 kgf·cm. Failure to do so may cause the Screw cap and the Mounting tab to fall off on the rear of ceiling panel.
14 10. REP AINTING THE SPEAKER Follow the procedure below when repainting the front grille: Step 1. Clean the front grille before painting. Wipe with a soft cloth dampened in a detergent. Caution Do not use thinner or other volatile liquids to clean the grille.
15 12. SAFETY AGENCY COMPLIANCE This product is for indoor use only. The F-122CU2's front-mounted rotary switch permits selection of speaker handling power (wattage) on 25 V or 70 V line operation or low impedance (8 Ω or 16 Ω ) operation. Depending on the switch settings, the unit complies with the different UL Categories as follows.
533-06-144-20 13. SPECIFICA TIONS Note: The design and specifications are subject to change without notice for improvement. • Accessories Front grille ............................................................ 1 Tile bridge .......................
デバイスTOA Electronics F-122CU2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
TOA Electronics F-122CU2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTOA Electronics F-122CU2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TOA Electronics F-122CU2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TOA Electronics F-122CU2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TOA Electronics F-122CU2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTOA Electronics F-122CU2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TOA Electronics F-122CU2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTOA Electronics F-122CU2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。