TOA ElectronicsメーカーF-1300Bの使用説明書/サービス説明書
ページ先へ移動 of 18
OPERA TING INSTRUCTIONS SPEAKER SYSTEMS F-1300B F-1300BT F-1300BTWP F-1300W F-1300WT F-1300WTWP Thank you for purchasing TOA's Speaker System. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ................................................................................. 3 2. GENERAL DESCRIPTION .............................................................................. 4 3. FEA TURES .......
3 When Installing the Unit • Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket. Doing otherwise may result in the unit falling down and causing personal injury and/or property damage. • Do not use other methods than specified to mount the bracket.
4 2. GENERAL DESCRIPTION TOA's F-1300 Series Speakers are compact two-way speaker systems designed for high efficiency, wide range, and high power input handling capability. These speaker systems can be installed and used in many different applications with combined use of the supplied accessories and/or the optional mounting brackets.
5 5. IMPEDANCE CHANGE (F-1300BT, F-1300BTWP, F-1300WT, and F-1300WTWP only) To change the impedance, use a standard screwdriver to rotate the rotary switch on the speaker's rear to select the desired input power. Note: The switch is factory-preset to 330 Ω .
6 7. NOTES ON OUTDOOR INST ALLA TION (F-1300BTWP and F-1300WTWP only) • Be sure to mount the speaker in a vertical (portrait-style) orientation. • Adjust the speaker's tilt angle within the shaded range shown below.
7 8. INST ALLA TION 8.1. Using the Supplied Brackets The speaker system is supplied with the following brackets. Use these brackets properly depending on the installation location and intended application. 30º [W all bracket] [Joint bracket] [Speaker bracket] 8.
8 8.3. W all Mounting Use the supplied wall bracket, joint bracket, and speaker bracket to permit adjustment of the horizontal and vertical* speaker coverage angles. * Vertical installation. Horizontal: Max. 75º, Vertical: Max. 45º downward Horizontal installation.
9 Step 2. Attach the joint bracket to the wall bracket using the supplied screws, adjust the horizontal speaker angle, then tighten the screws. Note: Match the orientation of the arrows on both the wall bracket and joint bracket. Step 3. Attach the speaker bracket to the speaker's rear using the supplied screws.
10 8.4. Ceiling Mounting Use the supplied joint bracket and speaker bracket. Note Speaker coverage angles can only be adjusted in the vertical direction (Max. 45º downward). Adjust the speaker's tilt angle within the shaded range shown below. Vertical orientation [Installation example] [Speaker angle vs.
11 Step 3. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and loosely securing the fixing bolt for temporary speaker installation. Step 4. Connect the speaker cable to the input terminal. Note Use a terminal cover when installing the speaker outdoors.
12 8.5. Speaker Stand Mounting The speaker can be mounted on the optional ST-16A Speaker Stand using the supplied joint bracket and speaker bracket. [Installation example] Note Mount the speaker so that it faces within the range of 15º upward and downward.
13 8.6. Pole Mounting (F-1300BTWP and F-1300WTWP only) To mount the speaker on a pole with diameter of 10 – 34 cm (3.94 – 13.39"), use the supplied wall bracket, joint bracket, and speaker bracket in combination with the optional YS-60B Pole Band.
14 Step 2. Attach the joint bracket to the wall bracket using the supplied screws, adjust the horizontal speaker angle, then tighten the screws. Note Match the orientation of the arrows on both the wall bracket and joint bracket. Step 3. Attach the speaker bracket to the speaker's rear using the supplied screws.
15 Step 2. Wipe clean the mesh grill and speaker cabinet with a soft cloth dampened in a detergent. Note Do not use thinner or other volatile liquids to clean the grill and cabinet. Step 3. Use spray paint to apply thin coat evenly overall the speaker.
16 10. SPECIFICA TIONS 10.1. F-1300B and F-1300W F-1300B F-1300W Bass-reflex type 50 W (continuous pink noise) 150 W (continuous program) 8 Ω 90 dB (1 W, 1 m) at installation in a semianechoic field .
17 F-1300BT F-1300WT Bass-reflex type 30 W 100 V line: 330 Ω (30 W), 1 k Ω (10 W), 3.3 k Ω (3 W), 10 k Ω (1 W) 70 V line: 170 Ω (30 W), 330 Ω (15 W), 1 k Ω (5 W), 3.
F-1300BTWP F-1300WTWP Bass-reflex type 30 W 100 V line: 330 Ω (30 W), 1 k Ω (10 W), 3.3 k Ω (3 W), 10 k Ω (1 W) 70 V line: 170 Ω (30 W), 330 Ω (15 W), 1 k Ω (5 W), 3.
デバイスTOA Electronics F-1300Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
TOA Electronics F-1300Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTOA Electronics F-1300Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TOA Electronics F-1300Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TOA Electronics F-1300Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TOA Electronics F-1300Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTOA Electronics F-1300Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TOA Electronics F-1300Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTOA Electronics F-1300Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。