TOA ElectronicsメーカーN-CC2360の使用説明書/サービス説明書
ページ先へ移動 of 20
NETWORK COLOR CAMERA N-CC2360 INSTRUCTION MANUAL 1. SAFETY PRECAUTIONS .......................... 2 2. LIST OF INCLUDED COMPONENTS AND PARTS ............ 3 3. GENERAL DESCRIPTION ........................ 4 4. HANDLING PRECAUTIONS .....................
2 1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.
3 Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. CAUTION When Installing the Unit • Avoid installing the.
4 3. GENERAL DESCRIPTION 4. HANDLING PRECAUTIONS • Do not direct the camera lens to the sun or strong lighting or light reflection. Exposure to direct sunlight could cause the CCD's color filter to deteriorate, leading to image discoloration. • Do not give the camera a great shock or vibration, as this will damage the camera.
5 (1) Power Input Terminal [24 V AC, 24 V DC] Connect this terminal to the 24 V AC or 24 V DC power supply. Note Do not connect 24 V AC or 24 V DC power when using a PoE-compatible hub. (2) Indicators [RDY BUSY ERR] RDY (green): Remains lit during normal operation.
6 Ceiling surface Lock lever Camera mounting bracket (optional) Pedestal Camera mount Camera mount Pedestal Camera mounting bracket (optional) Lock lever Camera mounting bracket (optional) W all surface W all surface LENS 1 3 2 4 Lens connector 1 2 3 4 Lens connector pin No.
7 6mm or less Lens • To avoid damaging the internal sections of the camera's lens mount, be sure that the lens flange is 6 mm or less thick as illustrated on the right. • C-mount lenses must be used in conjunction with the Lens Mounting Adapter CF-5 (optional).
8 7.1. Connection Example PoE compatible HUB Software Decorder 10BASE-T/ 100BASE-TX 10BASE-T/ 100BASE-TX 24V 2 1 24V 12C12C 10/100M PoE AUDIO OUT MONITOR OUT OUT IN CONT ACT RDY BUSY ERR FD/COL LINK /.
9 8. ADJUSTMENT 1. The RDY indicator lights when the power is supplied to the network camera. 2. Connect the monitor output terminal to the monitor so that the picture may be displayed on the monitor. 3. Set the Flicker-reduction switch of the mode switch to "ON" position if flicker is annoying.
10 6. Adjust the iris level • When using the DC input type lens Adjust the iris level on the Camera menu screen's "IRIS" item. 6-1 Check to confirm that Camera menu setting items are selected as follows.
11 F. A D J ANTI - FLICKER NC OFF ON Mode switch Focus adjustment switch Flicker-reduction switch Not used. Mode switch ( factory default ) [ N-CC2360 ] F. A D J ANTI-FLICKER NC ON OFF INITIALIZE RESET OFF ON OFF ON OFF ON OFF ON 9. ABOUT THE MODE SWITCH Set each switch to the position that provides the best picture reproduction.
12 No. 1 2 3 4 5 6 IN 1 IN 2 C OUT 1 OUT 2 C Contact input 1 Contact input 2 COM Contact output 1 Contact output 2 COM T erminal Name Contact name Day/ Night Select Contact input 1 or Contact input 2.
13 1 1. SETTING INITIALIZA TION Network settings can be reset to their factory defaults. 1. Either press the Reset key or switch on the power again while holding down the INITIALIZE key. 2. Continue to press the INITIALIZE key until the Ready indicator has switched from flashing to steady-on mode.
14 12. TROUBLESHOOTING Remedy Supply power independently to the Camera. Confirm that the cable type (category, null modem or straight) is appropriate for the connected port, then connect correctly. If the rough noise is annoying and distracting, lower the AGC level.
15 24 V AC, 50/60 Hz or 24 V DC or PoE (IEEE802.3af) 13 W (at 24 V AC), (8 W: PoE, 350mA: 24 V DC) Screwless connector (Solid cable: ø 0.4– ø 1.2 mm (AWG 26 – 16), Stranded cable: 0.
16 Note: The design and specification are subject to change without notice for improvement. MPEG-4: max. 4 Mbps 5 (MPEG-4: 4, JPEG: 1) In streaming mode: No limit (MPEG-4 only) Password authentication.
17 24 V AC, 50/60 Hz or 24 V DC or PoE (IEEE802.3af) 13 W (at 24 V AC), (8 W: PoE, 350mA: 24 V DC) Screwless connector (Solid cable: ø 0.4– ø 1.2 mm (AWG 26 – 16), Stranded cable: 0.
18 Note: The design and specification are subject to change without notice for improvement. MPEG-4: max. 4 Mbps 5 (MPEG-4: 4, JPEG: 1) In streaming mode: No limit (MPEG-4 only) Password authentication.
19.
133-12-993-90 URL: http://www.toa.jp/.
デバイスTOA Electronics N-CC2360の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TOA Electronics N-CC2360をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTOA Electronics N-CC2360の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TOA Electronics N-CC2360の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TOA Electronics N-CC2360で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TOA Electronics N-CC2360を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTOA Electronics N-CC2360の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TOA Electronics N-CC2360に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTOA Electronics N-CC2360デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
