Toroメーカー3.80E+13の使用説明書/サービス説明書
ページ先へ移動 of 12
Operator ’ s Manual Domestic English (EN) Form No. 3327-516 1800 Power Curve Snowthrower Model No. 38025—220020001 and Up.
2002 by The T oro Company All Rights Reserved Printed in USA 2 Contents Page Introduction 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Instructions 3 . . . . . . . . . . . . . . . . . . Safety and Instruction Decals 4 .
3 I MPORT ANT S AFETY I NSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: R EAD A LL I NST RUCTIONS B EFO RE U SING T HIS A P PLI ANCE W ARNING —T o reduce the risk of fire, electric shock, or injury , follow these safety instructions.
4 Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger . Replace any decal that is damaged or lost. On Handle 73-0460 1. Read the Operator ’ s Manual. 2. Electrocution 3.
5 1531 1 2 SQUEEZE Figure 2 1. Upper tubing 2. Lower tubing 3. Carefully insert the left side of the upper tubing into the end of the lower left side tubing (Fig. 2). 4. Squeeze the upper tubes together , and wiggle the upper tubes down until the mounting holes in the upper and lower tubing line up (Fig.
6 3. Secure the deflector to the discharge chute with 2 carriage bolts, metal washers, and locknuts. Note: Ensure that the square shoulders on the carriage bolts align with the inside square on the discharge chute. Position the metal washers to the outside of the chute deflector as shown in Figure 5.
7 the handle socket, insert the enlarged prong into the wide slot in the extension cord end. Refer to Important Safety Instructions on page 3 for additional information. 1540 1 Figure 8 1. Enlarged prong Operation Check the condition of the snowthrower before operating it.
8 A gap between the discharge chute and the chute deflector may allow snow and anything that can be picked up by snowthrower to fly in the direction of the operator . Thrown objects could cause serious personal injury . • Do not for ce the chute deflector too far forward so that a gap appears between the discharge chute and chute deflector .
9 Maintenance Note: Determine the left and right sides of the snowthrower by standing in the normal operating position. If the extension cord is plugged into the snowthrower and the key is in the handle, someone could accidentally operate snowthrower while you are performing maintenance on it, causing serious personal injury .
10 1525 1 Figure 16 1. Hex nu t 3. Hold the rotor and pull out the rotor shaft. 4. Remove the rotor . 5. Align the left side of the new rotor with the coupler . The 3 bosses on the rotor end must align with the slots on the coupler (Fig. 17). 1518 3 4 1 2 Figure 17 1.
11 5. Lift up the idler arm and slip the belt under the idler pulley (Fig. 20). 6. Rotate the rotor with your left hand while sliding the belt onto the large pulley with your right hand (Fig. 21). 1529 Figure 21 7. Assemble the idler spring (Fig. 18), making sure the idler pulley rides on the belt.
The T oro Promise A T wo-Y ear Full W arranty for Residential Use for the United States, Canada, and Mexico General Conditions Th e T oro Company and its af filiate, T oro W arranty Company , pursuant.
デバイスToro 3.80E+13の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toro 3.80E+13をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToro 3.80E+13の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toro 3.80E+13の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toro 3.80E+13で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toro 3.80E+13を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToro 3.80E+13の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toro 3.80E+13に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToro 3.80E+13デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
