Toroメーカー38583の使用説明書/サービス説明書
ページ先へ移動 of 20
Form No. 3358-430 Rev B Power Clear™ Snowthrower Model No. 38583—Serial No. 280000001 and Up Model No. 38584—Serial No. 280000001 and Up Operator's Manual Introduction R ead this infor mation carefully to lear n ho w to operate and maintain your product properly and to av oid injur y and product damage.
potential, comply with the f ollo wing safety instr uctions. This sno wthrower is capable of amputating hands and feet and of throwing objects. F ailur e to obser ve the following safety instr uctions could result in serious injur y .
• Look behind and use care when bac king up with the snow thro wer . • Disengag e po wer to the rotor blades when sno w throw er is transported or not in use. • Never operate the sno w thro wer without g ood visibility or light. Always be sure of your footing, and keep a r m hold on the handles .
Safety and Instructional Decals Important: Safety and instr uction decals are located near areas of potential danger . Replace damaged decals. 94-2577 1. T o engage the rotor blades, hold the control bar against the handle. 2. T o disengage the rotor blades, release the control bar .
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty . Use 1. No parts required – Unfold the handle. Screws 3 2. Chute assembly 1 Install the discharge chute. 1. Unfolding the Handle Procedure 1.
2. Installing the Discharge Chute 3 Screws 1 Chute assembly Procedure Install the discharge chute as shown (Figure 6). Figure 6 1. Discharge chute 2. Screw (3) Note: F or easier installation, use a small ratchet wrenc h to tighten the screws .
Mixing Gasoline and Oil This snowthro wer uses a 50:1 g asoline-to-oil mixture. Use T oro 50:1 2-Cycle Oil (Fuel Stabiliz er Added) or an equiv alent high-g rade , NMMA TCW III-cer tied 2-cycle oil. Important: T o prev ent engine damage, do not use automotiv e oil (such as SAE 30 or 10W30) or fuel mixed at the wrong gasoline-to-oil ratio.
Figure 1 1 1. Choke lever 3. Fir mly push in the primer 2 times with your thumb , holding the primer in a for a second before releasing it eac h time (Figure 12). Figure 12 Note: Remo ve your glo v e when you push in the primer so that air cannot escape from the primer hole.
If y ou lea ve the snowthrower plug ged into a power outlet, someone can inadver tently star t the snowthrower and injur e people or dama ge proper ty (model 38584 only).
Adjusting the Discharge Chute and Chute Deector T o adjust the discharge c hute, press the trig g er of the Quick Shoot™ control on the right hand side of the handle and mov e it up or down along the handle .
Operating T ips The rotor blades can throw stones, toys, and other foreign objects and cause serious per sonal injur y to the operator or to bystanders. • Keep the area to be cleared free of all objects that the rotor blades could pick up and throw .
Adjusting the Control Cable Checking the Control Cable Ser vice Inter val: After the rst hour—Check the control cable and adjust it if necessar y . Y early—Chec k the control cable and adjust it if necessary . Mov e the control bar bac k to ward the handle to remov e the slack in the control cable (Figure 20).
Figure 22 1. Remove the upper end of spring from this hole 3. Pivot point 2. Insert the upper end of spring into this hole 4. Upper end of spring Note: T he belt may slip (squeal) in wet conditions; to dr y out the driv e system, star t the rotor and r un it without a load for 30 seconds .
Figure 25 1. Screw (4) 3. Spark-plug wire 2. Shroud 7. Install the fuel tank cap . 8. Disconnect the wire from the spark plug . 9. Clean around the spark plug . 10. Remo v e the spark plug from the cylinder head. Important: R eplace a crack ed, fouled, or dir ty spark plug .
Figure 28 1. Brake spring (install on idler arm here) 3. Engine pulley 2. Idler pulley 4. Rotor pulley Note: R oute the new dri v e belt rst around the engine pulley , then the idler pulley , and nally around the loose rotor pulley positioned just abov e the rotor shaft (Figure 27).
Figure 32 4. Hold the disc harge chute in the straight-ahead position, pull the lo wer cable casing do wnward until y ou remo v e all the slack from the cable, and tighten the screw on the lo wer cable clamp securely (Figure 33). Figure 33 1. Lower cable casing 5.
Storage Storing the Snowthrower • Gasoline fumes are highl y amma ble, explosiv e, and dangerous if inhaled. If y ou store the product in an area with an open ame, the gasoline fumes may ignite and cause an explosion.
Notes: 18.
Notes: 19.
Conditions and Products Covered under The T oro Starting Guarantee The T oro Company and its af fi liate, T oro W arranty Company , guarantee that your T oro GTS (Guaranteed to Start) engine, when us.
デバイスToro 38583の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toro 38583をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToro 38583の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toro 38583の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toro 38583で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toro 38583を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToro 38583の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toro 38583に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToro 38583デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
