ToshibaメーカーB-442の使用説明書/サービス説明書
ページ先へ移動 of 34
TEC Bar Code Printer B-442 Owner's Manual Table of Contents.
LIST OF ST ANDARDS OF CONFORMITY (EU ONL Y) Manufacturer : Toshoba TEC Corporation Address : 570 Ohito, Ohito-Cho, Tagata-Gun, Shizuoka-Ken, 410-2392 Japan declares that following product Product Name.
(i) Safety Summary EM1-33046A Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment.
(ii) Safety Summary EM1-33046A CAUTION This indicates that there is the risk of personal Injury or damage to objects if the machines are improperly handled contrary to this indication.
Copyright © 1999 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, Japan Page EM1-33046A CAUTION: 1. This manual may not be copied in whole or in part without prior written permission of TEC. 2. The contents of this manual may be changed without notification.
1. INTRODUCTION EM1-33046A 1. INTRODUCTION 1. INTRODUCTION Thank you very much for purchasing the TEC B-442 Bar Code Printer. The attractive desktop printer delivers superior performance at an economical price. Both powerful and easy-to-use, the B-442 printer is your best choice among industrial direct thermal and thermal transfer label printers.
1. INTRODUCTION EM1-33046A 1. INTRODUCTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
1. INTRDUCTION EM1-33046A 1.1 APPLICABLE MODEL B - 4 4 2 - Q Q 1.1 APPLICABLE MODEL Destination Code QQ: North America QP: Europe GH12-GB: UK Thermal direct/Thermal transfer 1.2 UNP ACKING AND INSPECTION After receiving your B-442 Bar Code Printer, carefully inspect the device and its accessories.
2. SPECIFICATIONS EM1-33046A 2.1 PRINTER 2. SPECIFICA TIONS 2.1 PRINTER 2.1.1 Printer Block Type: Direct thermal or thermal transfer Print Speed: 1.5 inches or 2.0 inches per second Resolution: 203 dots per inch (8 dots per mm) Font Styles: Five alphanumeric fonts from 0.
2. SPECIFICATIONS EM1-33046A 2.2 OPTIONS 2.1.4 Communications Interface Communications: RS-232C (DB-9) at 2400, 4800, 9600 or 19200 baud Character Set: ANSI ASCII character set Word Length: 7 or 8 data bits, 1 or 2 stop bits, selectable parity Handshaking: XON/XOFF (on receive mode only) and CTS/DTR Input Buffer: 2 K bytes 2.
2. SPECIFICATIONS EM1-33046A 2) Tag Paper <Design> 12.0 mm ~ 273.0 mm 2.3 MEDIA 2.5 mm ~ 5.0 mm Backing Paper Label 1.0 mm 25.0 mm~115.0 mm BackingPaper 25.7 ± 0.3 mm Label 1) Thermal Label <Design> 2.3 MEDIA Fig. 2-2 Fig. 2-1 Fig. 2-4 Fig.
2. SPECIFICATIONS EM1-33046A <Non Print Area> Specification Spool type 40 mm ~ 110.0 mm Ø67 mm The ink side is outside of ribbon winding. Item Shape Width Max. OD Winding method Fig. 2-7 1.0 mm 1.0 mm Printing Area 1.0 mm 1.0 mm No. 1 2 3 4 2.4 RIBBON 4) Relationship between the head effective print width and paper.
2. SPECIFICATIONS EM1-33046A 2.5 CARE/HANDLING OF THE MEDIA AND RIBBON NOTE : When purchasing ribbon locally, they must meet the above size. There may be TEC-approved ribbons which do not fall within the above size, however, they have no functional problem.
3. OVERVIEW EM1-33046A 3.1 PRINTER PARTS 3. OVER VIEW 3.1 PRINTER PARTS Fig. 3-1 Top Front View 1. Cover Release Button 2. Pause Switch 3. Power, On-line and Error Indicator Lights 4.
3. OVERVIEW EM1-33046A 3.1 PRINTER PARTS Fig. 3-3 Rear View 1. Power On/Off Switch 4. 8 Position Dipswitch 2. Power Supply Connector 5. Label Insert Opening (for use with external labels) 3. RS-232 DB-9 Interface Connector 6. Cover Hinge Fig. 3-2 Interior View 1.
3. OVERVIEW EM1-33046A 3.2 EXTERNAL LABEL ROLL MOUNT Fig. 3-4 External Label Roll Mount 3.2 EXTERNAL LABEL ROLL MOUNT 3-3.
3. OVERVIEW EM1-33046A 3.3 SWITCHES AND INDICA TOR LIGHTS • INDICATORS PWR. (Power) Indicator The green PWR. indicator light will illuminate when the Power Switch is turned on. On-line Indicator The green On-line indicator will be on when the printer is ready to print.
4. DIP SWITCH FUNCTIONS EM1-33046A 4. DIP SWITCH FUNCTIONS Baud 19200 9600 4800 2400 SW-1 OFF ON OFF ON SW-2 OFF OFF ON ON 4. DIP SWITCH FUNCTIONS The DIP switches are located on the rear of the printer. WARNING! Turn the POWER OFF before changing the DIP switch settings.
5. SET UP PROCEDURE EM1-33046A 9 Printer Pin Function 1 +5 V 2 TxD 3 RxD 4 DSR 5 GND 6 RDY 7N / C 8 RDY 9+ 5 Host 9 25 Function Pin Pin RxD 2 3 TxD 3 2 DTR 4 20 GND 5 7 DSR 6 6 RTS 7 4 CTS 8 5 5.
6. LOADING LABEL AND TAG STOCK EM1-33046A 6. LOADING LABEL AND TAG STOCK 6. LOADING LABEL AND TAG ST OCK 1. Open the printer cover by pressing the two cover release buttons located on the right and left sides of the printer. While pressing the buttons, pull up on the printer cover.
6. LOADING LABEL AND TAG STOCK EM1-33046A 6. LOADING LABEL AND TAG STOCK Fig. 6-3 Feeding Labels through Adjustable Label Edge Guides 1. Printer Carriage Release Lever 2. Label 3. Front Rubber Roller or Platen 4. Adjustable Label Edge Guides Fig. 6-2 Inserting Label Supply Roll into Label Supply Roll Mounts 1.
7. SELF-PEELING FUNCTION EM1-33046A 7. SELF-PEELING FUNCTION Fig. 7-1 Setting Up Printer for Self-Peeling Function 1. Printer Carriage Release Lever 3. Self-peeling Roller 2. Front Rubber Roller 4. Backing Paper 7. SELF-PEELING FUNCTION 1. Remove the printer’s front panel.
8. RIBBON LOADING INSTRUCTIONS EM1-33046A 8. RIBBON LOADING INSTRUCTIONS 4 Fig. 8-1 Placement of Ribbon Supply Roll 1. Printer Carriage Release Lever 3. Ribbon Rewind Roll 2. Ribbon Supply Roll 4. Thermal Transfer Ribbon 8. RIBBON LOADING INSTRUCTIONS 1.
8. RIBBON LOADING INSTRUCTIONS EM1-33046A 8. RIBBON LOADING INSTRUCTIONS Fig. 8-2 Proper Placement of Label Stock and Thermal Transfer Ribbon 8-2.
9. INSTALL EXTERNAL LABEL ROLL MOUNT EM1-33046A 9. INSTALL EXTERNAL LABEL ROLL MOUNT Fig. 9-1 Install External Label Roll Mount 1. External Label Roll Mount 2.
10. INSTALL MOMORY MODULE EM1-33046A 10. INSTALL MEMORY MODULE NOTES: 1. Be sure to protect a memory module by putting it in it's protective cover when not in use in the printer. 2. Do not subject the memory module to any shocks or excessive forces.
11. SELF TEST EM1-33046A 11. SELF TEST 1 1. SELF TEST To initiate the Self Test Mode, depress the Feed key while turning on the printer. The printer will first calibrate the label length. If a label edge is not detected within 7", the printer will then stop attempting to feed labels and treat the media as continuous thermal paper.
12. DUMP MODE EM1-33046A 12. DUMP MODE 12. DUMP MODE After the Self Test Mode, the printer is in Dump Mode. In the Dump mode, any characters sent from the host computer will be printed in two columns as follows: on the left side of the paper are the characters received and on the right side are the corresponding hexadecimal value of the characters.
13. GENERAL MAINTENANCE EM1-33046A 13. GENERAL MAINTENANCE 13.1 CLEANING 13.1 CLEANING To help retain the high quality and performance of your printer it should be regularly cleaned. The greater the usage of the printer, the more frequent the cleaning.
13. GENERAL MAINTENANCE EM1-33046A 13.2 COVERS AND PANELS 13.2 COVERS AND P ANELS The covers should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution. NOTE: Clean printer cover with an electrostatic free cleaner for automated office equipment.
14. TOROUBLESHOOTING EM1-33046A 14. TROUBLESHOOTING WARNING! If you cannot solve a problem with the following solutions, do not attempt to repair it yourself. Turn the power off, unplug the printer, then contact your TEC representative for assistance.
15. ERROR MESSAGES EM1-33046A 15. ERROR MESSAGES 15. ERROR MESSAGES 1 Syntax Error The command format is incorrect. Check command manual carefully. The serial port setting is incorrect. Check dip switch and reset the printer. 2 Out of Range Numeric input is too large to be processed.
16. HOW TO CONNECT THE PRINTER WITH PROTABLE LCD KEYBOARD EM1-33046A 16. HOW TO CONNECT THE PRINTER WITH PORTABLE LCD KEYBOARD 16 . HOW T O CONNECT THE PRINTER WITH PORT ABLE LCD KEYBOARD To connect a portable LCD keyboard to the printer, we must write a program with particular commands as below: Example: DOWNLOAD "KEYBOARD.
PRINTED IN TAIWAN EM1-33046A E.
デバイスToshiba B-442の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba B-442をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba B-442の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba B-442の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba B-442で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba B-442を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba B-442の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba B-442に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba B-442デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
