ToshibaメーカーB-670-QQの使用説明書/サービス説明書
ページ先へ移動 of 32
TEC Thermal Printer B-670/680-QQ SERIES Owner ’ s Manual.
Copyright © 2002 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
(i) Safety Summary EO1-33015 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment.
(ii) Safety Summary EO1-33015 CAUTION This indicates that there is the risk of personal Injury or damage to objects if the machines are improperly handled contrary to this indication.
T ABLE OF CONTENTS 1. INTRODUCTION ...................................................................................... 1- 1 1.1 APPLICABLE MODEL ..................................................................... 1- 1 1.2 ACCESSORIES ............
1-1 1. INTRODUCTION EO1-33015 1. INTRODUCTION Thank you for choosing the TEC B-672/682 Series thermal/transfer printer. This new generation high performance/quality printer is equipped with the latest hardware including the newly developed high density (12 dot/mm, 305 dot/inch) edge print head.
2-1 2. SPECIFICATIONS EO1-33015 Supply voltage Universal (automatic switching) 85-138 V, 50/60 Hz 187-276 V, 50/60 Hz Be sure to use a power cord which meets the standard.
2-2 2. SPECIFICATIONS EO1-33015 2.2 OPTIONS 2.2 OPTIONS Description A stop and cut swing cutter This module strips the label from the back- ing paper with the take-up block and strip block. A 2MB RAM upgrade which enhances the image handling capability of the printer.
2-3 2. SPECIFICATIONS EO1-33015 NOTES: 1. The media specification other than above are unchanged. 2. When marking black marks on label rolls, the following requirements must be satisfied. When the gap length is less than 4 mm: The black mark length should be longer than the gap length.
3-1 3. OVERVIEW EO1-33015 3. OVER VIEW 3.1 FRONT/REAR VIEW 3.1 FRONT/REAR VIEW 3.2 OPERA TION P ANEL POWER ON LINE ERROR FEED REST ART PAUSE Fig. 3-2 Front View Rear View Message Display (LCD) Top Cover Head Lever Right Side Cover Power Switch 0: OFF 1: ON Media Outlet Operation Panel Fig.
4-1 4. DIP SWITCH FUNCTIONS (B-672 only) EO1-33015 4. DIP SWITCH FUNCTIONS (B-672 only) The DIP switches are located to the right of the Guide Wheel. 4. DIP SWITCH FUNCTIONS (B-672 only) NOTES: The Shaded settings are the factory default settings. "OFF" means "OPEN".
5-1 5. SET UP PROCEDURE EO1-33015 5. SET UP PROCEDURE 5.1 REQUIREMENTS FOR OPERA TION The B-672/682 has the following requirements: • The host computer must have a serial port or centronics parallel port. • To communicate with host, either an RS-232C cable or Centronics cable is required.
6-1 6. INSTALLING THE PRINTER EO1-33015 6. INST ALLING THE PRINTER 6.1 CONNECTING THE POWER CORD AND CABLES 6.1 CONNECTING THE POWER CORD AND CABLES Fig.
7-1 7. LOADING THE RIBBON EO1-33015 7. LOADING THE RIBBON 7. LOADING THE RIBBON WARNING! 1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the moving parts, push the switch in the “OFF” position to stop movement.
7-2 7. LOADING THE RIBBON EO1-33015 7. LOADING THE RIBBON 5. Push the ribbon core against the spring guide wheel, align the protrusion of the guide wheel with the notch of the ribbon core, then set the ribbon. 6. To remove the slack of the ribbon, turn the ribbon core in the direction indicated by the arrow.
8-1 EO1-33015 8. LOADING THE MEDIA 8. LOADING THE MEDIA 8. LOADING THE MEDIA 3. Lock the Media Holder securely with the Lock Lever. 4. Pass the Holder Shaft through the Media, then set one of the Media Holders and lock it securely with the Lock Lever.
8-2 EO1-33015 8. LOADING THE MEDIA 8. LOADING THE MEDIA 5. Turn the Lock Levers of the Media Holders to the unlock position and readjust the Media position to the center. Then lock the Media Holders securely with the Lock Levers. Fit the Media Guides to the Media.
8-3 EO1-33015 8. LOADING THE MEDIA 8. LOADING THE MEDIA 7. Set the black mark/feed gap sensor to the correct position by turning the adjusting knob. Turning the knob right will move the sensor towards the center of the media while turning left will move it away from the center of the media.
8-4 EO1-33015 8. LOADING THE MEDIA 8. LOADING THE MEDIA 8. The media is now loaded and the sensor position is set. Batch type: Media Fig. 8-6 Cutter type: Where a cutter is fitted load the media as standard and feed it through the cutter module. NOTES: 1.
8-5 EO1-33015 8. LOADING THE MEDIA 8. LOADING THE MEDIA Strip type: 1 Strip labels from the backing paper for about 200-mm long from the top edge of the label roll. 2 Lower the backing paper release bar. 3 Pass the backing paper between the strip roller and the backing paper holder.
9-1 EO1-33015 9. INSERTING THE OPTIONAL FLASH MEMORY CARD (B-672 only) 9. INSERTING THE OPTIONAL FLASH MEMORY CARD (B-672 only) 9. INSERTING THE OPTIONAL FLASH MEMOR Y CARD (B-672 only) Fig. 9-1 1. Turn the power off. 2. Insert the flash memory card into the memory card slot on the rear of the printer.
10-1 10. INSERTING THE OPTIONAL PCMCIA CARD (B-682 only) EO1-33015 10. INSERTING THE OPTIONAL PCMCIA CARD (B-682 only) 10. INSERTING THE OPTIONAL PCMCIA CARD (B-682 only) 1. Turn the power off. 2. Insert the PCMCIA card into the card slot at the rear of the printer.
11-1 EO1-33015 11. CARE/HANDLING OF THE MEDIA AND RIBBON 11. CARE/HANDLING OF THE MEDIA AND RIBBON 1 1. CARE/HANDLING OF THE MEDIA AND RIBBON • Do not store the media and ribbon for longer than the manufactures recommended shelf life.
12-1 EO1-33015 12. GENERAL MAINTENANCE 12.1 CLEANING 12. GENERAL MAINTENANCE WARNING! 1. Be cafeful when handling the print head as it becomes very hot. 2. Care must be taken not to injure yourself with the printer paper cutter. 3. Do not touch moving parts.
12-2 EO1-33015 12. GENERAL MAINTENANCE 12.1 CLEANING 7. Turn the pinch roller lever to the right. 8. Remove the white screw and detach the ribbon end sensor plate. NOTE: When installing the ribbon end sensor plate, be sure to fit both studs in the notches of the ribbon end sensor plate.
12-3 EO1-33015 12. GENERAL MAINTENANCE 12.2 UNDER THE MEDIA GUIDES 12.2 UNDER THE MEDIA GUIDES 1. Remove the Media Guides. 2. Remove the jammed Media. 3. Clean “dust and glue” on the Media Guides with a soft cloth moistened with alcohol. 4. Remount the Media guides using the screws.
12-4 EO1-33015 12. GENERAL MAINTENANCE 12.4 REMOVING JAMMED MEDIA 12.4 REMOVING JAMMED MEDIA 1. Turn the power off. 2. Open the top cover, and right side cover.
12-5 EO1-33015 12. GENERAL MAINTENANCE ■ Cleaning the Cutter Unit 1. Loosen two screws and remove the cutter cover. 2. Remove the white screw and media guide. 3. Remove the jammed paper and trash. 4. Clean the cutter with dry cloth. 12.4 REMOVING JAMMED MEDIA 5.
12-6 EO1-33015 12. GENERAL MAINTENANCE 12.5 THRESHOLD SETTING 12.5 THRESHOLD SETTING For the printer to maintain a constant print position it uses the transmissive sensor to detect the gap between labels by measuring the amount of light passing through the media.
13-1 EO1-33015 13. TROUBLESHOOTING 13. TROUBLESHOOTING 13. TROUBLESHOOTING Solution 1. Re-fit the media correctly. → Press the RESTART key. 2. Remove the cause of the jam and replace the media correctly. → Press the RESTART key. 3. Turn the power off then on again.
13-2 EO1-33015 13. TROUBLESHOOTING 13. TROUBLESHOOTING Solution Turn the power off and decrease the print head temperature. 1. Restart the printing by pressing the RESTART key. 2. Replace the print head. Turn the power off. Contact your Authorized Service representative.
13-3 EO1-33015 13. TROUBLESHOOTING 13. TROUBLESHOOTING Solution 1. Check that the media and the ribbon is loaded correctly. 2. Check whether the print head is set correctly or not. 3. Check the cabling between the printer and the host. Dirty print head.
デバイスToshiba B-670-QQの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba B-670-QQをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba B-670-QQの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba B-670-QQの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba B-670-QQで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba B-670-QQを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba B-670-QQの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba B-670-QQに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba B-670-QQデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
