ToshibaメーカーB-SV4Tの使用説明書/サービス説明書
ページ先へ移動 of 42
TOSHIBA Barcode Printer B-SV4T SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente Manual do Utilizador.
TOSHIBA Barcode Printer B-SV4T SERIES Owner’s Manual.
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • Schallemission: unter 70dB (A ) nach DIN 45635 (oder ISO 7779) • Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein.
Safety Summary ENGLISH VERSION EO1-33062 ( ) i Safety Summary Personal safety in handling or maintaining the equipmen t is extremely important. Warnings and Cautions necessary for safe handling are included in this manual.
Safety Summary ENGLISH VERSION EO1-33062 ( ) ii If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance.
ENGLISH VERSION EO1-33062 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW .......................................................................................................... E1 -1 1.1 Introduction ....................................................
ENGLISH VERSION EO1-33062 APPENDIX 2 INTERFACE .......................................................................................................... E A2-1 GLOSSARIES INDEX CAUTION! 1. This manual may not be copied in whole or in par t without prior written permission of TOSHIBA TEC.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.1 Introduction E1- 1 1. PRODUCT OVERVIEW 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories Thank you for choosing the TOSHIBA B-SV4T series barcode printer. This Owner’s Manual contains valuab le information from general set-up to confirming the printer's operation us ing test prints.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.4 Accessories E1- 2 When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your Authorised TOSHIBA TEC representative.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.5 Appearance E1- 3 1.5 Appearance 1.5.1 Dimensions 1.5.2 Front View 1.5.3 Rear View The names of the parts or units introdu ced in this section are used in the following chapters.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.5 Appearance E1- 4 1.5.4 Interior 1.5.5 Button and Indicator Lamp The FEED/PAUSE Button and the Indicator Lamp have the following functions: As the FEED button • Pressing this button when the printer is in online state causes a media feed.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.1 Precautions E2- 1 2. PRINTER SETUP 2.1 Precautions This section outlines the steps necessary to setup your printer prior to its operation. The section includes precautions, connecting cables, assembling accessories, loading media and ribbon, and performing a test print.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.2 Procedure before Operation E2- 2 2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF 2.3.1 Turning ON the Printer This section describes the outline of the printer setup. 1. Unpack the accessories and printer from the box.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.4 Connecting the Cables to the Printer E2- 3 2.3.2 Turning OFF the Printer 2.4 Connecting the Cables to the Printer 1. Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.5 Connecting the Power Adapter and the Power Cord E2- 4 2.5 Connecting the Power Adapter and the Power Cord 1. Make sure that the printer power switch is in the OFF (O) position. 2 . Insert the Power Cord into th e inlet of the Power Adapter.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.6 Opening/Closing the Top Cover E2- 5 2.6 Opening/Closing the Top Cover When opening or closing the Top Cover, please be sure to follow the instructions below. To open the Top Cover: 1. Turn the Cover Open Levers fr ontward, and gradually open the Top Cover.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.6 Opening/Closing the Top Cover E2- 6 2.6 Opening/Closing the Top Cover (Cont.) To hold the Top Cover at Position 2, first open the Top Cover until the Top Cover Support goes over Position 2 ( c ), then close the Top Cover a little ( d ) to secure the Top Cover Support.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2- 7 2.7 Loading the Media This section describes in detail how to load a media roll. 1. Turn OFF the printer. 2. Turn the Cover Open Levers fr ontward, and open the Top Cover. 3. When the inner core diameter of the media roll is 25.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2- 8 2.7 Loading the Media (Cont.) 6. Insert the both ends of the Media Shaft into the slots of the printer to place the Media Holder A ss’y into th e printer. Make sure that the media feeds from the top, as shown below.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2- 9 2.7 Loading the Media (Cont.) 11. After loading the media, manually set the Media Sensor to the correct position. The Feed Gap Sensor is included in the right Media Guide. Position of the Feed Gap Sensor can be set by fitting the Media Guides to the media ends.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2-10 Strip Feed Roller 2.7 Loading the Media (Cont.) Strip mode (Option): When issued in the strip mode, labels are automatically removed from the backing paper each time a label is printed.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2-11 2.7 Loading the Media (Cont.) Cut mode (Option): When the Cutter is installed, th e media is automatically cut. After loading the media as described on the previous pages, insert the leading edge of the media through the Media Outlet of the Cutter Cover.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2-12 2.7 Loading the Media (Cont.) When a media roll has an outside diameter exceeding 127 mm (5 ” ) or an inner core diameter of 38.1 mm (1.5 ” ), the optional External Media Roll Hanger is required.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.8 Loading the Ribbon E2-13 2.8 Loading the Ribbon When the printer is turned on, it automatically detects whether a ribbon is installed or not and switches the printing method between thermal transfer or direct thermal.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.8 Loading the Ribbon E2-14 2.8 Loading the Ribbon (Cont.) 5. Pull the leader tape of the ribbon downward, and feed it under the Print Head. 6. Attach the leader tape to the Paper Core with adhesive tape. 7.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities E2-15 2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities 2.9.1 Media Sensor Calibration 2.9.2 Self Print Test and Dump Mode This utility is used to calibrate th e sensitivity of the Feed Gap/Black Mark Sensor.
2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities E2-16 2.9.2 Self Print Test and Dump Mode (Cont.) Print test label sample The test print contents should be changed by the following commands and parameters: PROGRAM VERSION: VX.
3. MAINTENANCE ENGLISH VERSION EO1-33062 3.1 Cleaning E3- 1 3. MAINTENANCE 3.1 Cleaning 3.1.1 Print Head This chapter describes how to pe rform routine maintenance. To ensure the continuous high quality operation of your printer, you should perform a regular maintenance routine.
3. MAINTENANCE ENGLISH VERSION EO1-33062 3.1 Cleaning E3- 2 3.1.2 Platen/Sensors 3.1.3 Cover 1. Wipe the Platen with a soft cloth moistened with absolute alcohol. 2. Remove dust or paper particles fro m the Black Mark Sensor, Feed Gap Sensor, and Ribbon Sensor using an air blower.
3. MAINTENANCE ENGLISH VERSION EO1-33062 3.2 Care/Handling of the Media and Ribbon E3- 3 3.2 Care/Handling of the Media and Ribbon • Do not store media or ribbons for longer than the manufacturer’s recommended shelf life • Store media rolls on the flat end.
4. TROUBLESHOOTI NG ENGLISH VERSION EO1-33062 4.1 Troubleshooting Guide E4- 1 4. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions. 4.1 Troubleshooting Guide Problems Solutions The Online Indicator Lamp (green) is not illuminated.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.1 Printer EA1- 1 APPENDIX 1 SPECIFICATIONS Appendix 1 describes the printer specifications and supplies for use on the B-SV4T printer. A1.1 Printer The following are the printer specifications. Item Specifications AC100 to 240V, 50/60 Hz 100 to 120V: 2.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.2 Options EA1- 2 A1.2 Options Option Name Type Description Keyboard display unit KB-75-QM-R This m odule is an external intelligent keyboard display unit. Cutter module B-SV204-QM-R B-SV404-QM-R A cutter unit that makes stub cuts.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.3 Media EA1- 3 A1.3.1 Media Type (Cont.) Unit: mm (inch) Issue mode Item Batch mode Strip mode Cut mode c Width including backing paper 20 to 112 (0.8 to 4.4) d Media width 17 to 109 (0.7 to 4.3) Label 12 to 609.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.3 Media EA1- 4 A1.3.3 Detection Area of the Reflective Sensor The Reflective Sensor is movable within the full range of the media width. The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.4 Ribbon EA1- 5 A1.3.4 Effective Print Area The figure below illustrates the relation between th e head effective print width and media width. The figure below shows the effective print area on the media.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33062 APPENDIX 2 INTERFACE EA2- 1 APPENDIX 2 INTERFACE Interface Cables To prevent radiation and reception of electrical no ise, the interface cables must meet the following requirements: • Fully shielded and fitted with meta l or me tallized connector housings.
GLOSSARIES ENGLISH VERSION EO1-33062 GLOSSARIES GLOSSARIES Bar code A code which represents alphanumeric characters by using a series of black and white stripes in different widths. Bar codes are used in various industrial fields: Manufacturing, Hospitals, Libraries, Retail, Transpor tation, Warehousing, etc.
GLOSSARIES ENGLISH VERSION EO1-33062 GLOSSARIES Supply Media and ribbon Tag A type of media having no adhesive backing but black marks to indicate the print area. Usually tags are made of cardboard or other durable material. Thermal print head A print head using thermal transfer or thermal direct printing method.
INDEX ENGLISH VERSION EO1-33062 INDEX INDEX B Backing paper 2-10, A1-3 Bar code A1-1 Batch mode 2-6 Black mark 2-9, 2-15, A1-2, A1-4 Black mark length A1-3 Black mark sensor 1-4, 2-8, 2-9, 2-15, 3-2 C.
INDEX ENGLISH VERSION EO1-33062 INDEX S Serial interface 1-3, 2-3, A1-1 Strip mode 2-10, A1-3 Supply voltage A1-1 T Tag paper A1-2 Thermal transfer A1-1 Top cover support 1-4, 2-5, 2-6 3”-diameter m.
E EO1-33062.
デバイスToshiba B-SV4Tの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba B-SV4Tをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba B-SV4Tの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba B-SV4Tの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba B-SV4Tで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba B-SV4Tを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba B-SV4Tの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba B-SV4Tに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba B-SV4Tデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
