ToshibaメーカーEM1-33043Dの使用説明書/サービス説明書
ページ先へ移動 of 46
TEC P or table Pr int er B-210 SERI ES O w ner’ s M an ual Docu ment No . EM1-33043D T O SHIB A TE C CO R P O RA TION Table of Contents.
DECLARATI O N O F CONFORM ITY Manuf actur er Address Product Name m odel opti ons Safety EMC : T E C Cor por at ion : 570 O hi to. O hit o- Cho. Tagat a- G un, Shi zuoka-Ken, 41 D-23 Japan decl ar es .
E M 1 - 33043A T A BL E OF CONTENTS P age 1. INTRODUCTIO N ....................... . 1-1 1.1 APPL ICABL E M ODEL .......... . 1-10 1.2 ACCESSORIE S .................... . 1- 11 2. SPECIFICAT ION S ..................... . 2-1 2.1 PRINTE R .............
Page 9. GENERA L MAINTENANCE .......... 9-1 9.1 CLEAN ING ............................. 9-1 9.2 COVERS AND OPER ATION PAN EL .............. 9-3 9. 3 RE MOVI N G JA MMED ME DIA .................................... 9-4 10. TROUBLES HOOTING .............
1- 1 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION 1. INTRODUCTION Thank you for purchasing the TEC B-210 series portable printer. The B-210 printer displays its high performance with extraordinarily high speed printing up to 50.
1- 2 EM1-33043D 1. INTRODUCTION FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1- 3 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION Changes or modifications not expressly approved by manufacturer for compliance could void the user's authority to operate the equipment. CAUTION To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.
1- 4 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION Safety Precautions This Owner's Manual and the products (machines) which you have purchased contain indications which should be observed in order to use the machines safely and prevent harm to yourself and others and damage to property.
1- 5 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION • Avoid water, operation with wet hands or cleaning with a moistened cloth. Failure to do this may cause fire or electric shock. • Do not wipe the machine with a cloth moistened with thinner or other volatile solvent as this may cause fire or electric shock.
1- 6 EM1-33043D 1. INTRODUCTION • If the battery gets wet, dry it completely. Using a wet battery may cause fire or electric shock. • Be aware of the following precautions when using batteries. Otherwise they could heat up, burst or burn. ■ Do not throw the battery into fire or heat it with a microwave or oven, etc.
1- 7 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION CAUTION This indicates that there is the risk of personal injury or damage to objects if the machines are improperly handled contrary to this indication. • Keep away from flame or other sources of heat.
1- 8 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION • Unload the battery when the machine will not be used for a long time. Failure to do this may cause machine failure. • Keep the battery away from flame, a heat source or other locations subject to high temperature.
1- 9 EM1-33043D 1. INTRODUCTION 1. INTRODUCTION Precautions The following precautions will help to ensure that this machine will continue to function correctly.
1- 10 EM1-33043D 1. INTRODUCTION 1.1 APPLICABLE MODEL • B-210 Series Model name description B - 2 1 1 - G H 1 1 - G B 1.1 APPLICABLE MODEL Interface 11: Radio (418 MHz) + RS-232C 12: Radio (433 MHz).
1- 11 EM1-33043D 1. INTRODUCTION 1.2 ACCESSORIES 1.2 ACCESSORIES Owner’s Manual Print Head Cleaner Battery Media Guide.
2- 1 EM1-33043D 2. SPECIFICATIONS 2.1 PRINTER 2. SPECIFICATIONS 2.1 PRINTER Description 128 mm (W) x 88 mm (H) x 50 mm (D) Approximate 460 g, 450 g ∗ (Including a battery) -5 ° C ~ 40 ° C 25%~ 85% RH (No condensation) Batch mode/Strip mode Thermal print head Thermal direct 8 dots/mm (203 dpi) Max.
2- 2 EM1-33043D 2. SPECIFICATIONS 2.2 SERIAL INTERFACE (RS-232C) 2.2 SERIAL INTERFACE (RS-232C) Item Baud rate Protocol Signals Description 9600 bps XON/XOFF, 8 bit data, Even parity, Stop bit = 1 bit.
2- 3 EM1-33043D 2. SPECIFICATIONS Item Description Type Physical layer conforming to IrDA-SIR V1.0 Transmission speed 19200 bps Communicable distance 0.3 m max. Peak wavelength of 850 to 900 nm the infrared ray Communicable angle ± 15 ° degrees max.
2- 4 EM1-33043D 2. SPECIFICATIONS 2.5 MEDIA 2.5 MEDIA Label Receipt Black Mark (on reverse side) Receipt paper Fig. 2-1 G D H B A F G D C H I E B A Feed direction.
2- 5 EM1-33043D 2. SPECIFICATIONS 2.5 MEDIA Issue mode Item Label/Receipt 10.0 ~ 167.0 13.0 ~ 67.0 Pitch Label/Receipt 7.0 ~ 160.0 10.0 ~ 60.0 length Width including 34, 37, 40, 43, 46, 49, backing paper 52, 55 ± 0.5 Media width Label 31.0 ~ 52.0 Receipt 34, 37, 40, 43, 46, 49 52, 55 ± 0.
3- 1 EM1-33043D 3. APPEARANCE 3.1 FRONT/REAR VIEW 3. APPEARANCE 3.1 FRONT/REAR VIEW Fig. 3-1 Rear View Belt Holder Serial Interface Connector Front View Battery Cover Battery Cover Release Catch Power.
3- 2 EM1-33043D 3. APPEARANCE 3.2 OPERATION PANEL 3.2 OPERATION PANEL REPRINT Button Each time this button is pressed, the printer issues the same label as the previous one. When the button is held, the printer issues labels continuously. Receipts are fed for 20 mm by pressing this button once.
4- 1 EM1-33043D 4. INSTALLING THE PRINTER 4.1 LOADING THE BATTERY 4. INSTALLING THE PRINTER 4.1 LOADING THE BATTERY CAUTION: 1. Be sure to turn off the printer before loading the battery. 2. Use the specified battery only. Failure to do this may cause fire or electric shock.
4- 2 EM1-33043D 4. INSTALLING THE PRINTER 4.1 LOADING THE BATTERY 2) Load a fully charged battery into the printer. NOTE: Remove the battery pack cover from the battery, and then load the battery in the correct orientation as indicated in the following figure.
4- 3 EM1-33043D 4. INSTALLING THE PRINTER 2) Fit the media guide into a slot which corresponds to the width of media to be used. First insert portion 1 , then 2 until it snaps in position. 4.2 INSTALLING THE MEDIA GUIDE 4.2 INSTALLING THE MEDIA GUIDE NOTE: The media guide is not required for a 55 mm wide label roll.
4- 4 EM1-33043D 4. INSTALLING THE PRINTER 3) To remove or relocate the media guide, push up the pin on the media guide with a screw driver or equivalent, and remove the media guide from the printer.
5- 1 EM1-33043D 5. LOADING THE MEDIA A A 5. LOADING THE MEDIA 5. LOADING THE MEDIA This printer prints both labels and receipts. 1. Turn off the printer. 2. Slide the media cover release catches in the direction indicated by arrows A and open the media cover.
5- 2 EM1-33043D 5. LOADING THE MEDIA 5. LOADING THE MEDIA Fig. 5-3 3. Put a label roll or a receipt roll into the media holder unit in the orientation as shown below. Media Holder Unit Media Roll Fig. 5-2 • Batch issue 1. Insert the leading edge of the label roll into the media outlet.
5- 3 EM1-33043D 5. LOADING THE MEDIA 5. LOADING THE MEDIA 3. Turn on the printer and press the REPRINT button. The printer will align the print start position for the label. When using receipts, the printer will feed for 20 mm. 2. Close the media cover completely.
5- 4 EM1-33043D 5. LOADING THE MEDIA • Strip issue 1. Unroll the label roll a little and remove a label. Fig. 5-6 Fig. 5-5 2. Close the media cover completely.
5- 5 EM1-33043D 5. LOADING THE MEDIA 3. Turn on the printer and press the REPRINT button. The printer will align the print start position. NOTES: 1. Be sure to take up any slack in the media roll before closing the media cover. An incompletely closed cover will cause a media skew, print position misalignment, poor print quality, paper jam, etc.
6- 1 EM1-33043D 6. SECURING THE PRINTER TO YOUR WAIST 6. SECURING THE PRINTER TO YOUR WAIST 6. SECURING THE PRINTER TO YOUR WAIST CAUTION: Care should be taken not to drop the printer when securing it to your waist. 1) Lift the belt holder. Fig. 6-1 2) Insert the belt holder into your belt and lower the printer to secure it to your waist.
7- 1 EM1-33043D 7. ISSUING THE MEDIA 7. ISSUING THE MEDIA 7. ISSUING THE MEDIA CAUTIONS: 1. Radio communication between a handy terminal and the B-210 printer is guaranteed when the handy terminal is in the operator’s hand and the printer is secured at the waist.
7- 2 EM1-33043D 7. ISSUING THE MEDIA 7. ISSUING THE MEDIA 1. Turn on the printer. 2. Send data from the handy terminal to the printer. (Regarding the operation of the handy terminal, please refer to the handy terminal’s operating manual.) (Radio Communication Sample) Fig.
7- 3 EM1-33043D 7. ISSUING THE MEDIA 7. ISSUING THE MEDIA 3) After printing the receipt, press the REPRINT button to feed it to the position where it is easily cut. Each time the REPRINT button is pressed, the receipt is fed for 20 mm. 4. Trim off the printed media upward or downward with the cutter.
8- 1 EM1-33043D 8. CARE/HANDLING OF THE MEDIA 8. CARE/HANDLING OF THE MEDIA 8. CARE/HANDLING OF THE MEDIA CAUTION: Be sure to read carefully and understand the Supply Manual. Use only media which meet specified requirements. Use of non-specified media may shorten the head life and result in problems with bar code readability or print quality.
8- 2 EM1-33043D 8. CARE/HANDLING OF THE MEDIA • The thermal paper used for direct thermal printing must not have the specifications which exceed Ca ++ 800 ppm, Na + 800 ppm, K + 800 ppm and CL - 600 ppm. • Some ink used on pre-printed labels may contain components which shorten the print head's product life.
9- 1 EM1-33043D 9. GENERAL MAINTENANCE 9.1 CLEANING 9. GENERAL MAINTENANCE 9.1 CLEANING To help retain the high quality and performance of your printer it should be regularly cleaned. The greater the usage of the printer, the more frequent the cleaning.
9- 2 EM1-33043D 9. GENERAL MAINTENANCE 6. Remove paper particles or stains from the feed gap sensor, black mark sensor, and the batch/strip sensor with a soft cloth. Print Head Print Head Cleaner Fig. 9-1 Cutter Strip Roller Feed Gap Sensor Black Mark Sensor Platen Strip Mode Sensor Fig.
9- 3 EM1-33043D 9. GENERAL MAINTENANCE 9.2 COVERS AND OPERATION 9.2 COVERS AND OPERATION PANEL The covers should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution. NOTE: Clean the printer cover with an electrostatic free cleaner for automated office equipment.
9- 4 EM1-33043D 9. GENERAL MAINTENANCE 9.3 REMOVING JAMMED MEDIA 9.3 REMOVING JAMMED MEDIA 1. Turn off the printer. 2. Open the media cover. 3. Remove the media roll from the printer. 4. Remove the jammed media. DO NOT USE any sharp implement or tool as these could damage the printer.
10- 1 EM1-33043D 10. TROUBLESHOOTING Cause Media end The media cover is open. The printer is jammed with media. The print head element is broken. A communication error occurred. The battery voltage is low. Status Indicator Blinks Lights 10. TROUBLESHOOTING 10.
10- 2 EM1-33043D 10. TROUBLESHOOTING Check Did the status indicator light and then go off at power on? Is the printer turned on? Is the media roll loaded correctly? Is the status indicator blinking or.
.
.
PRINTED IN JAPAN EM1-33043D 99010500 GS E.
デバイスToshiba EM1-33043Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba EM1-33043Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba EM1-33043Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba EM1-33043Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba EM1-33043Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba EM1-33043Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba EM1-33043Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba EM1-33043Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba EM1-33043Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
