ToshibaメーカーIK - HD1Cの使用説明書/サービス説明書
ページ先へ移動 of 35
For Customer Use Enter below the Serial # which is located on the bottom of the cabinet. Retain this information for future ref- erence. Model # IK-HD1C Serial # CAMERA CONTROL UNIT INSTRUCTION MANUAL.
2 SAFETY PRECAUTIONS Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data.
3 Disclaimer We disclaim an y responsibility and shall be held harmless for any damages or losses incurred b y the The following description is for that a camera head “IK-HD1H” connected to this camera control unit. user in any of the f ollowing cases: 1.
4 1 CAUTIONS ON USE AND INSTALLATION ............................................ 2 COMPONENTS ....................................................................................... 3 ITEMS CONTROLLED BY THE ON SCREEN DISPLAY ........................
5 (2) External sync frequency range .................................................................................... (3) Using the unit with external sync signal ....................................................................... (3.1) H (Horiz ontal) phase adjustm ent .
6 1 Camera Control Unit ............................................................................................... 1 2 Accessori es a Instruction manual ........................................................................................ 1 2.
7 Available selections Item Preset value (Factory s etting) MANUAL AUTO, MANUAL, SS MODE OFF OFF AUTO, MANUAL, OFF MODE OFF AWB AWB, ATW, MANUAL MODE AUTO level -100 0 100 0 AUTO peak/average 00 10 05.
8 3 4 2 1 12 3 45 8 7 9 6 Camera cable for “IK-HD1H” terminal POWER switch POWER LED FILE button GAIN button DISP button P AGE button MENU UP (SHD) button MENU DOWN (SHD) button DA T A UP (A WB) button DA T A DOWN (A BB) button DC IN 12V terminal REMOTE terminal Y/G terminal P B /B terminal P R /R terminal EXT.
9 㽽 DC IN 12V terminal Accept a DC power input (12V). 㽾 Y/G terminal Outputs Y or G. (BNC connector) 㽿 P B /B terminal Outputs P B or B. (BNC connector) 㾀 P R /R terminal Outputs P R or R. (BNC connector) 㾁 REMOTE terminal To connect to a RS-232C device for remote control function.
10 DC IN 12V 1 +12V 2 +12V 3 GND 4 GND REMOTE 1 2 3 4 5 6 7 8 9 NC NC NC NC GND NC RXD TXD NC 5 3A Connector Pin A ssignments 䊶 Only use optional camera head model # IK-HD1H with this camera controller. The use of another head m ay cause damage to the control unit and camera head.
11 㽲 Refer to the item “5. CONNECTION”, connec t the equipment correctly. A camera head "IK-HD1H" needs to be connected to this camera control unit from this section on.
12 AT W Automatic Tracking White Balance 䋩 䋩 䋩 䋩 AW B 䋨 䋨 䋨 䋨䋨 䋨 䋨 䋨 Automatic White Balance 䋩 䋩 䋩 䋩 MA NUA L 䋨 䋨 䋨 䋨 Manual White Balance 䋩 䋩 䋩 䋩 Outline The camera m easures the object color tem perature and adjusts the white balance automatically.
13 Meaning Display A WB OK Automatic white balance adj ustment f inished correctly. A WB NG LEVEL LOW Automatic white balance adjustm ent cannot be perf ormed bec ause the video l evel is too low. Adjust the video level by increasing the illumination or opening the lens iris.
14 Five scene files (A, B, C, D, E) are available as user memories for this unit. These are chosen depending on shooting conditions. By using the [FILE] button, the camera operation is changed immediately from the currently selected Scene File to the next.
15 Due to the lens used or the environmental condition, color shading may occur at the upper and lower edge of the screen. If this happens, the shading correction function can be used to decrease the amount of color shading.
16 Various setti ngs can be control led on the unit b y using the on scr een menu disp layed on the monitor . The contents once set are memorized in the scene files (A, B, C, D, E) selected, so if the power turns off, it is unnecessar y to set again when us ing the unit nex t time.
17 䊶 Select the m enu to change the setting by referring to the item “7.1 Using the Menus ”. 䊶 When the [MENU UP], [MENU DOW N] buttons ar e pushed, the “ 㸢 ” on the s creen moves up and down. Move the “ 㸢 ” to the item whose setting you wish to change.
18 䋨 䋨 䋨 䋨 1 䋮 䋮 䋮 䋮 1 䋩 䋩 䋩 䋩 Changing the setting in AUTO mode Shutter mode AUTO, MA NUAL, SS Video level adjustment -100 to 100 Peak and average ratio adjustment 00 10 to 10.
19 (d) Changing the automatic shutter zone area The available picture area is shown by the shading correction on the screen that is parted in 64. 㽲 Move the “ 㸢 ” to AREA by pushing [MENU UP], [MENU DO W N] buttons. 㽳 Select the m easurem ent light area by pushing [DATA UP], [DATA DOW N] buttons .
20 䋨 䋨 䋨 䋨 1 䋮 䋮 䋮 䋮 2 䋩 䋩 䋩 䋩 Changing the setting in MANUAL mode Shutter mode AUTO, MANUAL, SS -- 1 SHUTTER -- <FILE A> Shutter speed setting MODE MANUAL OFF, 1/100s, 1.
21 2 GAIN (Video gain) GAIN has three modes ; AUTO, MANUAL, OFF. Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the three modes : AUTO, MANUAL, OFF.
22 䋨 䋨 䋨 䋨 3 䋩 䋩 䋩 䋩 WHT BAL(White Balance) The W HT BAL has three m odes; AW B, ATW , MANUAL. Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the three modes : AWB, ATW, MANUAL.
23 䋨 䋨 䋨 䋨 3 䋮 䋮 䋮 䋮 2 䋩 䋩 䋩 䋩 Changing the setting in ATW(A uto matic Tracking W hite balance) mode White balance mode AWB, ATW, MANUAL -- 3 WHT BAL -- <FILE A> R PAINT .
24 䋨 䋨 䋨 䋨 3 䋮 䋮 䋮 䋮 3 䋩 䋩 䋩 䋩 Changing gain in MANUA L mode White balance mode AWB, ATW, MANUAL Red gain adjustment -100 to 100 -- 3 WHT BAL -- <FILE A> Blue gain adjust.
25 䋨 䋨 䋨 䋨 4 䋩 䋩 䋩 䋩 PROCESS Gamma correctio n ON, OFF Gamma correction level setting -10 to 10 -- 4 PROCESS -- <FILE A> GAMMA ON/OFF ON GAMMA 0 Detail gain setting -7 to 7 DTL G.
26 䋨 䋨 䋨 䋨 4 䋮 䋮 䋮 䋮 3 䋩 䋩 䋩 䋩 Changing detail (outline) gain 㽲 Move the “ 㸢 ” to DT L GAIN by pushing [MENU UP], [MENU DOW N] buttons. 㽳 Select the desired value of the detail gain by pushing [DATA UP], [DATA DO W N] buttons.
27 䋨 䋨 䋨 䋨 5 䋩 䋩 䋩 䋩 MATR IX(Matrix color correction) Matrix color correction ON, OFF Red hue setting -- 5 MATRIX -- <FILE A> Yellow hue setting R e d g a i n s e t t i n g MATRI.
28 䋨 䋨 䋨 䋨 6 䋩 䋩 䋩 䋩 SYNC When an exter nal sync s ignal is input, the displa y changes f rom INT ( internal sync) to EXT. (external s ync) automatically. I N T E X T 䋨 䋨 䋨 䋨 6 䋮 䋮 䋮 䋮 1 䋩 䋩 䋩 䋩 INT screen -- 6 SYNC -- <FILE A> MODE INT 䋨 䋨 䋨 䋨 6 䋮 䋮 䋮 䋮 2 䋩 䋩 䋩 䋩 Changing EXT.
29 䋨 䋨 䋨 䋨 7 䋩 䋩 䋩 䋩 OPTION OUTPUT Y/P b /P r , RGB SHADING MODE SET, MANUAL, OFF -- 7 OPTION -- <FILE A> RS232C baud rate 9600bps, 19200bps OUTPUT Y/P b /P r OSD OUTPUT ALL ON, .
30 䋨 䋨 䋨 䋨 7 䋮 䋮 䋮 䋮 5 䋩 䋩 䋩 䋩 Changing RS232C baud rate 䋨 䋨 䋨 䋨 7 䋮 䋮 䋮 䋮 6 䋩 䋩 䋩 䋩 Changing OSD OUTPUT mode 㽲 Move the “ 㸢 ” to BAUD RATE by pushing [MENU UP], [MENU DOW N] buttons. 㽳 Select either 9600bps or 19200bps by pushing [DATA UP], [DATA DOW N] buttons.
31 When using the unit with an exter nal sync s ignal to EXT. SYNC term inal on the r ear panel. W hen the exter nal sync si gnal is input, the c amera autom atically switches its sync from the internal s ync to the external sync.
32 Items to be checked Symptom No picture 䍃 Is power supplied correctly? 䍃 Is the lens iris adjusted correc tly? 䍃 Is the power switch on, and the power LED illuminated? 䍃 Are the camera and v.
33 Power supply 12V DC 㫧 10% Power consumption Approx. 10.3 W (including a camera head) Pick-up system RGB, 3CCD, Micro prism system Image sens or 1/3 inch, IT 䋭 CCD Output pixels Horiz ontal : 1920, Vertical : 1080 Scanning system 2 䋺 1 interlace Scan frequency [59.
34 Unit : mm [inch] 10. EXTERNA L APPEA RANCE DIA GRAM 㪋㪋㪅㪍㩷㪲㪈㪅㪎㪍㪴 㪋㪇㩷㪲㪈㪅㪌㪏㪴 㪈㪏㪍㩷㪲㪎㪅㪊㪉㪴 㪈㪈㪇㩷㪲㪋㪅㪊㪊㪴 㪈㪏㪅㪏㪊 㪲.
Limited Warranty – T OSHIBA CCD Camera The Imaging Systems Division of T oshiba America Information Systems, Inc. ("ISD") makes the follo wing limited warranties with regard to this CCD Camera ("Product"). These limited w arranties e xtend to the Original End-User ("Y ou[r]").
デバイスToshiba IK - HD1Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba IK - HD1Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba IK - HD1Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba IK - HD1Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba IK - HD1Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba IK - HD1Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba IK - HD1Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba IK - HD1Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba IK - HD1Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
