ToshibaメーカーL630-BT2N13の使用説明書/サービス説明書
ページ先へ移動 of 230
GMAD00243010 04/10 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 162 in this gui de.
2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical ap.
4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n.
5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can.
6 5.375 x 8.375 ver 2.3 In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer . Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment.
7 5.375 x 8.375 ver 2.3 3 The standard connecting arrangemen t (telephone jack type) for this equipment is jack t ype(s): USOC RJ11C. Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card.
8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health W ireless LAN products, like other radio de vices, emit radio frequency electromagnetic energy . The lev el of energy emitted by W i reless LAN devices howe ver is f ar much less than the elect romagnetic energy emitted b y wireless devices lik e for example mobile phones.
9 5.375 x 8.375 ver 2.3 Canada – Indust ry Canada (IC) This device complies with RS S 210 of Industry Canada. The installer of this radio equipment mu st ensure that the antenna is loc ated or point.
10 5.375 x 8.375 ver 2.3 EU Declaration of Conformity TOSHIB A declares that this product conforms to the follo wing Standards: This product is carrying the CE-Mark in accordance w ith the related European Directiv es. The party responsib le for CE-Marking is TOSHIB A Europe GmbH, Hammfelddamm 8, 41460 Neuss, Ger many .
11 5.375 x 8.375 ver 2.3 VCCI Class B Information Modem W arning Notice This information is only applicable if your computer has a modem. Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN).
12 5.375 x 8.375 ver 2.3 Using this Equipment in Japan In Japan, the frequency bandwi dth of 2,400 MHz to 2,483.5 MHz for second generation low-po wer data communicatio n systems such as this equipment ov erlaps that of mobile object identifi cation systems (premises radio station and specified lo w-power radio station).
13 5.375 x 8.375 ver 2.3 The indication sho wn belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.
14 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on wha t type of wi reless device is in your computer .
15 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 622ANHMW and 633ANHMW Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
16 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Atheros ® Wireless Wi-Fi ® Link AR5B95 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
17 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Ukraine United Kingdom Uruguay USA V enezuela V ietnam Y emen Zimbabwe België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special reg istration with IB PT/BIPT is required.
18 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply .
19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8192E This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8191SE This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
22 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that.
23 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table.
24 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization.
25 5.375 x 8.375 ver 2.3 Ta i w a n The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations.
26 5.375 x 8.375 ver 2.3 Copyright This guide is copyrighted by T o shiba Amer ica Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide canno t be reproduced in any form without the prior written permission of T o shiba.
27 5.375 x 8.375 ver 2.3 T rademarks Satellite and eco Utility are either registered trademarks or trad emarks of T oshiba America Information Systems, In c. and/or T oshiba Cor poration. Adobe and Photoshop are either registered trademarks or tr ademarks of Adobe Systems Incorporated in the Unite d States and/or other countries.
28 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 35 This guide ...............................................................37 Safety icons ............................
29 Contents 5.375 x 8.375 v er 2.3 Turning on the power .......................................48 Setting up your software ...................................48 Registering your computer with Toshiba ................49 Adding optional external devices.
30 Contents 5.375 x 8.375 v er 2.3 Turning off the computer ........................................82 Options for turning off the computer ................ 83 Using the Shut down command ........................ 85 Using and configuring Hibernation mode .
31 Contents 5.375 x 8.375 v er 2.3 Inserting an optical disc ................................. 107 Playing an audio CD ........................................109 Playing optical media ......................................109 Recording optical media .
32 Contents 5.375 x 8.375 v er 2.3 Chapter 4: Exploring Y our Computer’ s Features ................... 129 Exploring the desktop ........................................... 129 Finding your way around the desktop .............130 Setting up for co mmunications .
33 Contents 5.375 x 8.375 v er 2.3 TOSHIBA eco Utility™ ...........................................159 TOSHIBA Service Station ......................................160 TOSHIBA PC Health Monitor .................................160 Chapter 6: If Something Goes Wrong .
34 Contents 5.375 x 8.375 v er 2.3 Appendix A: Hot Keys/TOSHI BA Cards .......... ........................ 190 Hot Key Cards .......................................................190 Using the Hot K ey Cards .................................191 Application Cards .
35 5.375 x 8.375 ver 2.3 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T oshiba com puter , your work and entertainment can accompan y you where ver you go. Y our co mputer model may be ENERGY ST AR ® qualified.
36 Introd uctio n 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 30% and 60% less energ y depending on how it is used.
37 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated.
38 Introd uctio n Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data.
39 Introduction Other documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are de signed to accommodate all possible configurations for an entire product Series.
40 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information.
41 Getting Started Selecting a place to work T o keep your computer in prime operating condition, pro tect your work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
42 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin.
43 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer .
44 Getting Started Connecting to a power so ur ce Please handle your computer carefully to avo id scratching or damaging the surface. Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery .
45 Getting Started Connecting to a po wer sour ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to t.
46 Getting Started Char ging the main battery ❖ Glows white when the main battery is fully charged ❖ Is unlit when the main battery has d ischarged, the battery is not charging, or the A C adaptor.
47 Getting Started Using the computer for the f irst time Using the computer for the first time The computer is now ready for you to turn it on and be gin using it. Opening the display panel 1 Facing the front of the com puter, locate the center of the display panel.
48 Getting Started Using the computer for the fir st time T urning on the power T o turn on the computer: 1 Make sure an y external de vices (such as the A C adaptor , if you plan to use AC po wer rather th an battery power) are properly connected and ready .
49 Getting Started Re gistering your computer with T oshib a Registering your computer with T oshiba Product registration is strongly reco mmended, and allows T oshiba to send you periodic updates, announcement s, and special offers applicable to your p roduct.
50 Getting Started Adding memory (optional) Before adding external devices or memory , T oshiba recommends setting up your software. See “Setting up your s oftware” on page 48 . Installing a memory module Memory modules can be installed in the memory mo dule slots on the base of the computer .
51 Getting Started Adding memory (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start . (Sample Image) Shut down button 2 Click the Shut do wn button in the lo wer-right corner of the Start menu. The computer closes all open programs, shuts down the operating system, and then turns off.
52 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre ws that secure the memory module slot cover . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cov er .
53 Getting Started Adding memory (optional) If your system has the memory modules stacked on top of one another , you must remove the top module first before removing/installing the bottom module. For this model, Slot A is the bottom slot. Slot B is the top slot.
54 Getting Started Adding memo ry (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module.
55 Getting Started Adding memory (optional) 16 T urn the computer right side up. Make sure to remov e the soft cloth from the work surface be fore restarting the computer .
56 Getting Started Adding memory (optional) Do not try to remove a memor y module with the computer turned on. Y ou can damage the computer and the memor y module. Do not remove the memory module while the computer is in Sleep or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost.
57 Getting Started Adding memory (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screws.
58 Getting Started Recovering the Internal Stor age Drive 7 Reconnect the cables. 8 Restart the computer . TECHNICAL NOTE: Y ou must have at least one memor y module installed for the computer to work. Checking total memory When you add or remove a memory mo d u l e , you can check that the computer has recognized the change.
59 Getting Started Recovering the Internal Stora ge Drive A recov ery image of your computer is stored on the internal storage dri ve, and the image can be restored b y running the recovery utilities directly f rom your internal storage drive as described in the sections below .
60 Getting Started Recovering the Internal Stor age Drive Recovering to out-of-box state (recommended recovery method) Recoverin g an internal storag e driv e to its out-of-box state deletes all partitions on the drive and all info rmation stored in those partitions.
61 Getting Started Recovering the Internal Stora ge Drive (Sample Image) W arning screen 5 When the T oshiba Recov ery W i zard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
62 Getting Started Recovering the Internal Stor age Drive (Sample Image) Reco very of F a ctory Default Software scr een 7 Click Next . A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to sa ve your work to e xternal media before proceeding (see “Backing up your work” on page 104 ).
63 Getting Started Recovering the Internal Stora ge Drive The “Recov er to a custom size pa rtition” option restores you r C: dri ve to its out-of-box state, and allows you to specify the size for the C: partition.
64 Getting Started Recovering the Internal Stor age Drive (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
65 Getting Started Recovering the Internal Stora ge Drive 9 Click Next to be gin the recovery . When the process is complete, a message displays indicating that the C: dri ve has been recov ered. 10 Press any k ey on the ke yboard to restart the computer .
66 Getting Started Recovering the Internal Stor age Drive 4 A warning screen appears stating that when the recovery is ex ecuted all data will be deleted and rewritten.
67 Getting Started Recovering the Internal Stora ge Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover without changing the hard drive partitions . (Sample Image) Reco very of F a ctory Defa ult Software scr een 7 Click Next .
68 Getting Started Recovering the Internal Stor age Drive When you create recovery DVDs/media, only the operating system files, applications, and drivers originally shipped with the computer are backed up to the external media and can be res tored from this media.
69 Getting Started Recovering the Internal Stora ge Drive Y ou cannot store your system’ s applications on the same drive or disc/disc set where the rest of the system recovery files are stored. For example, you will need to store the applications on one USB flash drive and the system recover y files on another USB flash drive.
70 Getting Started Recovering the Internal Stor age Drive Restoring from recovery DVDs/media The recovery process deletes information stored on the internal storage drive. Be sure to save your work to ex ternal media before executing the recovery (see “Backing up your work” on page 104 ).
71 Getting Started Recovering the Internal Stora ge Drive 2 Do one of the following: ❖ If your recov ery files are on D VDs, insert the f irst reco very D VD into your optical disc driv e. ❖ If your recov ery files are on a USB flash driv e, connect the USB flash dri ve to your computer .
72 Getting Started Erasing the Internal Stora ge Drive Erasing the Internal Storage Drive Erasing the internal storage drive will delete all data on the drive, including the partitions. Be sure to create recovery DVDs/media and back up your data to external media before erasing the internal storage drive.
73 Getting Started Checking the internal stor age drive oper ating status (Sample Image) Er ase the har d disk scr een 4 Click Next . A confirmation message displays reminding you that all data on the internal storage driv e will be lost.
74 Getting Started Using the T ouchP ad™ Installing drivers and applications The T oshiba Application Installer allows you to reinstall the drivers and applications that were original ly bundled with your computer .
75 Getting Started Using the T ouchP ad™ Refer to the table below for specif ic instructions on perfor ming each operation. The pointer is the icon (usually an arrow) that moves on the screen when you slide your finger across the T ouchPad or move a mouse connected to your computer .
76 Getting Started Using the T ouchP ad™ Scroll vertically Slide your finger along the right edge of the T ouchPad in the direction you want to scroll.
77 Getting Started Using the T ouchP ad™ Adjusting T ouchPad™ settings While you are typing, the on-screen pointer may seem to move or jump around “by itself” to ran dom locations on the screen. The on-screen pointer may also seem to automatically select text, click buttons, and acti vate other user interf ace elements.
78 Getting Started Using external display de vices T ouchPad setting options vary by computer model. The T ouchPad settings are accessible through the Mou se Properties option of the Windows Control Panel. For more information, please visit www .support.
79 Getting Started Using external display de vices Selecting video cables T o connect a device to the HDMI™ O ut port, you must purchase an HDMI™ cable.
80 Getting Started Using external display de vices Directing the display output when you turn on the computer Once you ha ve connected an e xte rnal displ ay devi ce, you can choose to use the internal display only , the external de vice only , or both simultaneo usly .
81 Getting Started Using an external k e yboard Adjusting the quality of the external display T o obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
82 Getting Started T urning off the computer T o connect a printer to your computer: 1 Connect the printer cable to th e printer and then connect the other end to one of the computer’ s USB ports. 2 Plug the printer’ s power cable into a li ve A C outlet.
83 Getting Started T urning off the computer It is a good idea to turn of f your computer when you are not using it for a while. If you are using the computer for the first time, lea ve the computer plugged into a power source (e ven though the computer is off) to fully charge the main battery .
84 Getting Started T urning off the computer ❖ Restarting from Hib ernation takes a little mor e time and consumes more main b attery po wer than restarting from Sleep. ❖ When starting up again, the computer returns to the state in which you left it, including all open programs and files you were using.
85 Getting Started T urning off the computer Using the Shut down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns of f your computer .
86 Getting Started T urning off the computer 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. (Sample Image) Edit Plan Settings screen 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears.
87 Getting Started T urning off the computer These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Shut down if you want the computer to shut down when you close the display panel.
88 Getting Started T urning off the computer 2 Click Hibernate in the pop-up menu . The computer sav es the state of all open pro grams and f iles, turns of f the display , and then turns off. Configuring Hibernation mode options Y ou can place the computer into Hibernation mode by either pressing the power b utton or closing the display panel.
89 Getting Started T urning off the computer 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 5 Select Hibernate for the options you want.
90 Getting Started T urning off the computer Starting again from Hibernation mode T o start up the computer from Hibernation mode, press the power button until the ON/OFF light gl o ws white.
91 Getting Started T urning off the computer T o use any of these methods, you f irst need to enable them using the Power Options feature. 1 Click Start , Contro l Panel , System and Security , and then Po wer Options . The Po wer Options window appears.
92 Getting Started T urning off the computer 5 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options screen 6 Select Sleep for the options you want.
93 Getting Started Customizing your computer’ s settings Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the ON/OFF light glows white.
94 Getting Started Caring for your computer Moving the computer Before moving your computer, e ven across the room, make sure all dri ve acti vity has ended (the intern al storage driv e and optical disc dri ve indicator lights stop glowing) and all e xternal peripheral cables are disconnected.
95 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive.
96 Learning the Basics Using the ke yboar d ❖ Back up your files to ex ternal media on a regular basis. Label the backup copies clearly and store them in a safe place.
97 Learning the Basics Using the ke yboar d Character keys T yping with the character keys is very mu ch li ke t yp ing on a typewriter , e xcept that: ❖ The space bar creates a space char acter instead of just passing ov er an area of the page. ❖ The lo wercase letter l (el) and the number 1 are not interchangeable.
98 Learning the Basics Using the ke yboar d F1 through F12 are called function keys because the y ex ecute programmed functions when pressed. Used in combinatio n with the Fn key , fun ction keys marked with icons ex ecute specific functions on the computer .
99 Learning the Basics Starting a pr o gram Using the overlay to type numeric data The keys with the numbers on th eir right front are the numeric ov erlay keys. T o turn the numer ic ove rlay on, press Fn and F11 simultaneously . The numeric overlay light glows wh en the numeric overlay is on.
100 Learning the Basics Starting a pr ogra m If you pause with your mouse on All Programs, it will open it up . Y ou may need to scroll up or down to see the complete list. 2 Click the program group, in this example, Accessories . The Accessories menu is displayed.
101 Learning the Basics Saving your work 7 In the right part of the window , double-click wordpad . The operating sy stem opens W ordPad. T o close the program, click the Clo se button in the upper-right corner of the program’ s window .
102 Learning the Basics Saving your work Saving files 1 Click on the arrow in the upper -left corner of your W indows ® -based application to display the drop-down menu, and then click Sav e . If you are working with a docum ent that already has a f ile name, this i s all you need to do.
103 Learning the Basics Printing your work Microsoft ® W ord file. Creating your own extension is usually unwise, since the program is unlikely to recognize a strange extension and may refuse to handle your file correctly . TECHNICAL NOTE: By default, the Windows ® operating system does not show file extensions.
104 Learning the Basics Backing up your work 3 Specify the print parameters. For e xample, the range of pages and number of copies to print. 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer .
105 Learning the Basics Using the optical disc drive TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to over write a file that already exists on the internal storage drive. Make sure the backup v ersion is the one you want before overwriting the existing file.
106 Learning the Basics Using the optical disc drive ❖ Some Blu-ray Disc™ movies hav e online content that can be accessed from the disc. T o view this content, your computer must be connected to the Intern et.
107 Learning the Basics Using the optical disc drive Optical disc drive components The optical disc dri ve is located on the side of the computer . Y our optical disc driv e may look like this: (Sample Illustration) Optical disc drive Drive in-use indicator light —Indicates when the driv e is in use.
108 Learning the Basics Using the optical disc drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for optical discs” on page 111 .
109 Learning the Basics Using the optical disc drive 8 Make sure the disc is completely on the spindle and is lyin g flat on the tray . If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance.
110 Learning the Basics Using the optical disc drive Recording optical media Depending on the configuration, your computer may come with an optical disc driv e that allo ws you to: ❖ Play pre-recorded and recorded optical media. ❖ Read/write data and multi -media files to recordable optical media.
111 Learning the Basics T oshiba’ s online r esour ces Removing a disc with the computer off T o remov e a disc with the computer turned of f: 1 Insert a slender object, such as a straightene d paper clip, into the manual eject hole. The disc tray sl ides partiall y out of the d riv e.
112 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your comput er while trav eling. T oshiba’ s energy-saver design Y our computer enters a l o w-power suspension mode when it is not being used, thereby conserving energy and sa ving money in the process.
113 Mobile Computing Running the computer on battery power Battery Notice Battery life rating is for comparison purposes only , and does not indicate the battery life that will be obtained by any indi vidual user .
114 Mobile Computing Char ging batteries TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on. Power management Y our computer ships with the power.
115 Mobile Computing Char ging ba tteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet.
116 Mobile Computing Monitoring main battery power T o recharge the R TC battery , plug the computer into a li ve electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC battery because it charges while the computer is on.
117 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ) with the ON/OFF light ( ). When the ON/OFF light flashes amber , it indicates that the system is suspended (using the Windows ® operating system Sleep command).
118 Mobile Computing Monitoring main battery power Determining remaining battery power Wait a few moments after turning on the computer before trying to monitor the remaining battery power . The computer needs this time to check the battery’ s remaining capacity and perform its calculations.
119 Mobile Computing Monitoring main battery power Setting batter y notifications Y ou can set two notifications. Each notification can be set to alert you when a specified percentage of remaining battery po wer has been reached.
120 Mobile Computing Monitoring main battery power ❖ How much you use the internal storage dri ve or other optional devices ❖ Where you are working, since operating time decr eases at low temperat.
121 Mobile Computing Monitoring main battery power 2 Select an appropriate plan for your work en vironment or create your own custom plan. 3 Click Create a po wer plan in the left pane to set up a new plan. T o edit a plan or to edit advanced settings, continue to the following steps.
122 Mobile Computing Using the T OSHIB A eco power plan 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: eco and Balanced. 3 Release the Fn key . The hot ke y card disappears. Y ou are now in the selected mode.
123 Mobile Computing Changing the main battery Removing the battery from the computer T o remove the battery: 1 Sav e your work. 2 T urn of f the computer or place it in Hibernation mode according to the instructions in “Using and configuring Hibernatio n mode” on page 87 .
124 Mobile Computing Changing the main battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately . Always dispose of used battery packs in compliance with all applicable laws and regulations.
125 Mobile Computing T aking car e of your battery 3 Slide the battery release lo ck to the locked position. (Sample Illustration) Locking the battery r elease lock 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 123 .
126 Mobile Computing T aking car e of your battery ❖ T o replace the main battery , use an identical battery that you can purchase through the T oshiba W eb site at accessories.toshiba.com . ❖ A rev erse polarity condi tion should be avoided with all batteries.
127 Mobile Computing Disposing of used batteries ❖ If you are not going to use the computer for more than eight hours, disconnect the A C adaptor . ❖ Store spare battery packs in a cool dry place out of direct sunlight. Disposing of used batteries The life of a battery pack depends on usage.
128 Mobile Computing T raveling tips T oshiba is dedicated to preservi ng the en vironment by sponsoring Call2Recycle™ , a program of the Rechar geable Battery Recycling Cor por atio n. For more information and for drop-off locations, visit www .rbrc.
129 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system.
130 Exploring Y our Computer’ s Features Explorin g the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, taskbar , notification area, and background pattern.
131 Exploring Y our Computer’ s Features Exploring the desktop ❖ TECHNICAL NOTE: If you delete a large number of files or very large files from the internal storage drive, there may be insufficient space available in the Re cycle Bin to hold these files.
132 Exploring Y our Computer’ s Features Setting up for communications T askbar Each time you open a program, a button associated with that program appears on the taskbar . With some programs, a b utton appears on the taskbar for each document or window you open.
133 Exploring Y our Computer’ s Features Setting up for communications For information on ho w to set up a wireless connection, refer to your wireless networking device documentation or your network administrator . T o enable or disable wireless communication, use the Hot Key Fn + F8 .
134 Exploring Y our Computer’ s Features Setting up for communications Connecting a modem to a telephone line (A vailable on certain models.) Y our computer may come with a built-in modem th at can be connected to a standard voice-grade telephone line.
135 Exploring Y our Computer’ s Features Explorin g audio featur es Exploring audio features Y ou can use your computer to record sounds usi ng the computer’ s internal microphone (av ailable on certain models) or an optional external microphone.
136 Exploring Y our Computer’ s Features Using the W eb Camera TECHNICAL NOTE: When using amplified speakers, use speakers that require an external power source.
137 Exploring Y our Computer’ s Features Using the Memory car d r eader Using the Memory card reader (A vailable on certain models.) The Memory card reader suppor ts the use of Memory Stick ® , Memory Stick PR O™, Memory Stick PR O Duo™, Memory St ick Duo™, Secure Digital™ (SD™), or MMC ® (MultiMediaCard ® ) media.
138 Exploring Y our Computer’ s Features Using the Memory car d r eader When inserting memory media, do not touch the metal contacts. Y ou could expose the storage area to static electri city , which can destroy data.
139 Exploring Y our Computer’ s Features Using the eSA T A/USB combo port Using the eSA T A/USB combo port (A vailable on certain models.) Y our computer includ es an eSA T A/USB combo port, which can be used with both eSA T A (external Serial Advanced T echnology Attachment) de vices and USB devices.
140 Chapter 5 Utilities Y our computer includes seve ral utilities designed to help you to reconfigure your system to best meet your individual needs. T ogether , these allo w you to ascerta in certain system details, set additional options, or change de fault options.
141 Utilities TOSHIB A Assist ❖ TOSHIB A Accessibility ❖ TOSHIB A eco Utility™ ❖ TOSHIB A Service Station ❖ TOSHIB A PC Health Monitor TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings.
142 Utilities TOSHIB A Assist Connect The feature a vailable in this category is: ❖ Bluetooth ® Settings (Sample Image) T OSHIBA Assist window – Connect tab.
143 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secure tab.
144 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility ❖ TOSHIB A HDD Protection Utility (Sample Image) T OSHIBA Assis.
145 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Setup (Hardware Settings) ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Access.
146 Utilities TOSHIB A Application Installer TOSHIBA Application Installer The T OSHIB A Application In staller allo ws you to re install the dri vers and applications that were originally bundled with your computer .
147 Utilities Setting passwor ds Setting passwords Setting a password lets you walk aw ay from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can wo rk on your computer again.
148 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to se.
149 Utilities Setting passwor ds 6 Click OK . The supervisor password util ity dialog box appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK .
150 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , TOSH IBA , Utilities , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab .
151 Utilities TOSHIB A F ace Recognition Utility TOSHIBA Face Recognition Utility Y our computer may come with the TOSHIB A Face Recognition utility . This utility provides another way to log on to your co mputer . For high security purposes, TOSHIBA Face Re cognition is not a suitable substitute for Windows ® passwords.
152 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose problem s with devices in your computer . Refer to the online Help documentation with in the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have.
153 Utilities TOSHIB A HDD Pr otection Utility TOSHIBA HDD Protection Utility The TOSHIB A HDD Protection Utility controls your computer’ s hard disk dri ve (HDD) protection feature, which parks the HDD whene ver motion is detected on the computer .
154 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Control Panel , Hard ware and Sound , and then under Devices and Printers , click Mouse , or click the Mouse icon in the Op timize tab of TOSHIB A Assist .
155 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the TOSHIB A configuration management tool av ailable through th e W indows ® operating system.
156 Utilities TO S H I B A H a rd w a re S e t u p ❖ Display —Allows you to change various default settings for the built-in display When the computer restarts, it remembers the last configuration. If data does not appear on the display you are using after starting in Sleep mode, press Fn + F5 .
157 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 203 ).
158 Utilities TOSHIB A Accessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required.
159 Utilities TOSHI BA eco Utility™ TOSHIBA eco Utility™ The TOSHIB A eco Utility™ monitors your power sa vings from using the eco power plan by tracking real-time power consumption and accumulated savings o ver time.
160 Utilities TOSHIB A Service Station TOSHIBA Service Station The TOSHIB A Service Station helps you keep your n e w computer running at its best by notifying you when updated software, firmw are, documentation or other informat ion is av ailable for your computer .
161 Utilities TOSHIB A PC Health Monitor Y ou may disable the TOSHIB A PC Health Monitor at an y time by uninstalling the software via t he W indows ® Control Panel. Doing so will automatically delete all collected inform ation from the internal storage dri ve.
162 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself.
163 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask .
164 If Something Goes Wrong Pr oblems when you turn on the computer The computer displays the WARNING RESUME F AILURE/Windows Error Recovery – Windows did not shut down successfully message. T o continue, select Start W indows normally . This can happen if the computer was put into Sl eep mode and the battery has discharged.
165 If Something Goes Wrong The W indows ® operating system is not working If the trickle-charging does not prov e ef fectiv e, visit the T oshiba W eb site at pcsupport.tosh iba.com and see the Support Bulletin Step-Charging the computer ’ s battery (click the Ask Iris ® link and search for the s upport b ullet in by name).
166 If Something Goes Wrong The W indo ws ® operating system is not working ❖ The operating system responds dif ferently from the normal routine. ❖ The screen does not look right. Unless a hardware de vice has failed, problems usually occur when you change the system in some way such as installing a ne w program or adding a device.
167 If Something Goes Wrong The W indo ws ® operating system is not working If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is v ery slow . Many f actors contribute to the speed with which you can surf the Internet.
168 If Something Goes Wrong F ixing a pr oblem with De vice Manag er Fixing a problem with Device Manager Device Manager pro vides a way to check and change the configuration of a de vice. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable.
169 If Something Goes Wrong Memory pr oblems Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be hardware or e ven software related. It is w orthwhile checking for these firs t: 1 Click Start , and then click the Shut do wn button in the lo wer-right corner of the Start menu.
170 If Something Goes Wrong P ower and the batteries If the A C po wer light stil l does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance. The A C adaptor and power cord/c able work corr ectly , b ut the battery will not charge.
171 If Something Goes Wrong K e yboar d pr oblems Keyboard problems If, when you type, strange things happen or nothin g happens, the problem may be related to the keyboard itself. The keyboard pr oduces unexpected characters. A keypad o verlay may be on.
172 If Something Goes Wrong Display pr oblems If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’ s po wer cord/cable is f irmly plugged into a working p o wer outlet. ❖ Check that the cable connecting the external monitor to th e computer is fi rmly attached.
173 If Something Goes Wrong Disk or storag e drive pr oblems Small bright dots appear on yo ur TFT display when y ou turn on y our compu ter . Small bright dots may appear on your screen display when you turn on your computer .
174 If Something Goes Wrong Optical disc drive pr oblems 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system er rors ❖ Scan for and attempt reco very of bad sectors 7 Click Start . Error- checking tests and repairs the storage driv e.
175 If Something Goes Wrong Optical disc drive pr oblems Y ou press the disc eject b utton, but the drive tray does not slide out. Make sure the computer is connect ed to a po wer source and turned on. The optical disc dri ve eject mechanism requires po wer to operate.
176 If Something Goes Wrong Optical disc drive pr oblems While viewing a Blu-ray Disc™ movie the sound is not coming from the computer's speakers. Y ou can change the destination of the audio signal in Sound properties in the Control Panel. Blu-ray Disc™ player T echnology .
177 If Something Goes Wrong Sound system pr oblems Sound system problems No sound is coming from the computer’ s speakers. Adjust the volume control. T ry pressing Fn + Esc to see if v olume mute is disabled. Check that the volume control on the computer is turned up.
178 If Something Goes Wrong Modem pr oblems The printer will not print wh at y ou see on the scr een. Many programs display information on the screen differently from the way they print it. S ee if your program has a print previe w mode. This mode lets you see your work exactly as it will print.
179 If Something Goes Wrong W ireless networking pr oblems ❖ V e rify that your computer can det ect access points or routers. If it can detect a W i-Fi ® access point or router then it may be a configuration issue. ❖ V erify that signal strength is good usin g the utility provided with the W i-Fi ® adapter .
180 If Something Goes Wrong D VD and BD operating pr oblems ❖ If you hav e enabled any security provisions (closed system, MA C address filtering, W ired Equivalent Pri v acy [WEP], etc.), check the access point v endor's W eb site for recent firmw are upgrades.
181 If Something Goes Wrong Develop good computing habits A blank scr een appears while watching a D VD-R OM or BD-R OM movie or title. Change the setting for when to tu rn off the display using the following steps: 1 Click Start , Contro l Panel , System and Security , and then Po wer Options .
182 If Something Goes Wrong Develop good computing habits If you hav e installed your own programs, you should back up these programs as well as your data file s. If something goes wrong that requires you to reformat your inte rnal storage dri ve and start again, reloading all your programs and data files from a backup source will sa ve ti me.
183 If Something Goes Wrong Develop good computing habits 2 In the left pane, clic k System protection . The System Protecti on tab of th e System Properties windo w appears. 3 Click Create... 4 In the input field, enter a name that is descripti ve enough to be easily understood in the future, such as “Before inst alling Brand X Accounting app.
184 If Something Goes Wrong Develop good computing habits Backing up your data or your entire computer with the Windows ® operating system The most v aluable component of y our computer system is the data you create and store on its internal storage drive.
185 If Something Goes Wrong Develop good computing habits then be able to easily restore the W indows ® operating system to the state it was in prior to the installation, undoing any changes that the installatio n process introduced.
186 If Something Goes Wrong If you need further assistance The eSA T A device is not recognized fr om Sleep or Hibernation mode. A connected eSA T A device may not be recognized if it is connected to the computer’ s eSA T A/USB comb o port (av ailable on certain models) while the computer is in Sleep or Hibernation mode.
187 If Something Goes Wrong Other T oshiba Internet W eb sites T oshiba’ s T echnical Support Web site For technical support, or to stay current on the most recent softw are and hardware options for your computer, and for other product information, be sure to regularly check the T o shiba W eb site at pcsupport.
188 If Something Goes Wrong T oshiba’ s worldwide off ices T oshiba’ s worldwide offices A ustralia T oshiba (Australia) P ty . Limited 84-92 T alav era Road North Ryde NSW 2113 Sydney Australia Canada T o shiba Canada Ltd. 191 McNabb Street Markham, Ontario L3R - 8H2 Canada France T oshiba Systèmes (France) S.
189 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additio nal T osh iba worldwide locations, please visit: www .toshiba. co.jp/i ndex. htm . United States T oshiba America Information Systems, Inc. 9740 Irvine Boulev ard Irvine, California 92618 United States The Rest of Europe T oshiba Europe (I .
190 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards prov ide a quick way to modif y selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot K ey Cards and Application Cards.
191 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off.
192 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 141 .
193 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Cards: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stacked” card on the far right of the display .
194 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards.
195 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer .
196 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window .
197 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep m ode” on page 90 .
198 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 87 .
199 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the p o w e r - o n di sp l ay o p t i on s (only th.
200 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode.
201 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module.
202 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T ouchPad™. For more information on using the T ouchPad, see “Using the T ouchPad™” on page 74 .
203 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution.
204 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Cursor control overlay Numeric overlay or Fn + This TOSHIB A Card or hot ke y turns the cursor control ov erlay on and off.
205 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot ke y turns the scroll lo ck feature on and off. Fn + This hot ke y t urns th e TOSHIB A Z o om in g Utility to zoom out. Fn + This hot key turns the TOSHIBA Zooming Utility to zoom in.
206 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer ships w ith the correct power su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world.
207 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide.
208 Glossary DIMM Dual Inline Memo ry Module DOS Disk Operating System DPI Dots Per Inch DV D Digital V ersat ile (or V id eo) Disc DV D - R O M Digital V ersatile (o r V id eo) Disc Read-Only Memory .
Glossary 209 RO M Read-Only Me mory RT C Real-T ime Clock SD Secure Digital SDRAM Synchronous Dynamic Random Access Memory SSD Solid State Driv e TFT Thin Film Tr ansistor USB Univ ersal Serial Bus URL Uniform Resource Locator WA N W ide Area Network www W orld W ide W eb Te r m s The following terms may appear in this user’ s guide.
210 Glossary B backup —A copy of a f ile, usually on a remov able disk, kept in case the original file is lost or damaged. Basic Input/Output System (BIOS) —See BIOS. baud rate —The speed at which a communication de vice, such as a printer or mo dem, transmits in formation.
Glossary 211 C cache —A section of very fast memory in which frequently used information is duplicated for qu ick access. Accessing data from cache is faster than accessing it from the computer’ s main memory . See also CPU ca che, L 1 c ache, L2 c ache.
212 Glossary CPU cache —A section of very fast memory residing between the CPU and the computer’ s main memory that temporarily stores data and instructions the CPU will need to ex ecute commands and programs. See also cach e, L1 ca che, L 2 ca che.
Glossary 213 document —Any file created with an appl ication and, if sav ed to disk, gi ven a name by which it can be retrie ved. See also fil e . double-click —T o press and release the point ing device’ s primary button rapidly twice without moving the pointi ng device.
214 Glossary F fil e —A collection of related in formation, saved on disk with a uniqu e name. A file may be a program, information used by a program, or a document. See also docum ent. File Allocation T able (F A T ) —The section of a s t o r a g e d r iv e that keeps track of the location of stored files.
Glossary 215 H DM I ( High-Def inition Multimedia Interface) —A n interface used to transmit high quality audio and video signal via a single cable in digital format, providing better picture quality than analog signal.
216 Glossary LAN (Local Area Network) —A group of com puters or other devices dispersed ov er a relati vely limited area and connected by a communications link that enables any de vice to interact with an y other on the network.
Glossary 217 motherboard —The computer’ s main circuit board that contains the processor , memory , and other primary com ponents. MS-DOS pr ompt —See system pr ompt. multi-function drive —A D VD dri ve that can r ead and write to CD and DV D m e d i a .
218 Glossary password —A unique string of characters en tered by a user to verify his or her identity to the computer or the network. PC Card —A credit-card-sized expansion card designed to increase the capabilities of computers.
Glossary 219 Random Access Memory —See RAM. Read-Only Memory —See RO M . reb o ot —See boot , re s t a r t . removable disk —A disk that can be remov ed from a disk dri ve.
220 Glossary shortcut —See k eyboar d shortcut . Sleep —A feature o f some W indo ws ® operating systems that allows you to turn off the computer without exiting your open applications and to continue from where you left of f when you turn the computer on again.
Glossary 221 W We b —See W o rld W ide W eb . Wi- F i ® —A registered trademark term of the W i-Fi Alliance that stands for W ireless Fidelity , and is anot her term for the communication protocol to permit an Ethernet connect ion using wireless communication components.
222 Index A A C adaptor 44 AC p o w e r 114 A C power light 44 accessing network 133 adding memory check total memor y 58 memory (optional) 49 optional external devices 49 adequate ventilation cooling.
223 Index running computer on battery power 112 safety precautions 125 setting notifications 119 battery indicator light 117 BIOS Setup see TOSHIB A Hardware Setup Blu-ray Disc™ using 105 , 106 but .
224 Index display devices ext e rn al 78 display output settings 80 display panel opening 47 display , external adjusting 81 disposal information 27 disposing of used batteries 127 DV D caring for dis.
225 Index desktop 130 moving to desktop 130 recycle bin 130 safety 38 installation memory module 50 installing a charged battery 124 battery 122 memory modules 49 mouse 81 Instruction Manual fo r Safe.
226 Index N network accessing 133 Connect to the Internet 133 connecting your comp uter 133 networking wireless 132 notification area 132 O ON/OFF indicator light 117 online resources To s h i b a 111.
227 Index USB-compatible 81 printing a file 103 problem solving modem not recei ving or transmitting 178 Startup options 166 program, starting 99 program, starting from Start menu 99 projector connect.
228 Index Sleep mode 84 configuring 90 configuring options 90 hot key 197 po wering do wn 90 Shut down 90 starting again from 93 using 90 software Setup W izard 48 software program starting 99 startin.
229 Index Disk Defragmenter 174 display error message 172 display problems screen is blank 171 D VD BD player 180 eject button 17 5 error message, warning resume failure 164 Error-checking 173 eSA T A.
230 Index W indows® operating system desktop 129 troubleshooting 165 W indo ws® Start menu starting a program 99 wireless netw orking 132 troubleshooting 178 wizards Connect to the Internet 133.
デバイスToshiba L630-BT2N13の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba L630-BT2N13をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba L630-BT2N13の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba L630-BT2N13の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba L630-BT2N13で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba L630-BT2N13を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba L630-BT2N13の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba L630-BT2N13に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba L630-BT2N13デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
