ToshibaメーカーM30-35の使用説明書/サービス説明書
ページ先へ移動 of 338
Toshiba Personal Computer Satellite M30-35 Series Maintenance Manual TOSHIBA CORPORATION File Number 960-455.
ii Satellite M30-35 Maintenance Manual (960-455) Copyright © 2003 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein.
Satellite M30-35 Maintenance Manual (960-455) iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite M30-35 Series.
iv Satellite M30-35 Main tenance Manual (960-455) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite M30 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems.
Satellite M30-35 Maintenance Manual (960-455) v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition.
vi Satellite M30-35 Main tenance Manual (960-455) Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ... 1-1 1.2 System Unit Block Diagram .
Satellite M30-35 Maintenance Manual (960-455) vii Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test .......
viii Satellite M30-35 Maintenance Manual (960-455) Chapter 4 Replacement Procedures 4.1 General .................................................................................................................... ... 4-1 4.2 Battery Pack .............
Satellite M30-35 Maintenan ce Manual (960-455) ix Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ...................................................
x Satellite M30-35 Maintenance Manual (960-455).
Chapter 1 Hardware Overview.
1 Hardware Overview 1-ii Satellite M30-35 Maintenance Manual (960-455).
1 Hardware Overview Chapter 1 Contents 1.1 Features................................................................................................................... ....1-1 1.2 System Unit Block Diagram ..............................................
1 Hardware Overview 1-iv Satellite M30-35 Maintenance Manual (960-455) Figures Figure 1-1 Front of the computer .....................................................................................1-6 Figure 1-2 System un it configuration.............
1.1 Features 1 Hardware Overview 1 Features 1.1 Features The Toshiba Satellite M30 Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Sem iconductor (CMOS) technology extensively to provide compact size, minim um weight, low power usage and high reliability.
1 Hardware Overview 1.1 Features CD-RW/DVD Drive This drive is a combination of DVD-ROM and CD-R/RW Drive. . It is full-size and runs either 12cm (4.
1.1 Features 1 Hardware Overview Universal Serial Bus (USB2.0) Three USB ports are provided. The ports comply with the USB2.0 standard, which enables data transfer speeds 40 times faster than USB1.1 standard. USB1.1 is also supported. IEEE 1394 port The computer comes with one IEEE 1394 port.
1 Hardware Overview 1.1 Features Sound system The sound system is equipped with the following features: AC 97 Link • • • • • • • Sound CODEC: STAC9750 Stereo speakers Built-in Microp.
1.1 Features 1 Hardware Overview Internet button This button launches an Internet browser. If the computer’s power is off, you can press this button to turn on the computer’s power and launch the browser automatically in one step. TOSHIBA Console button This button launches an application automatically.
1 Hardware Overview 1.1 Features The front of the computer is shown in figure 1-1 and the system unit configuration is shown in figure 1-2. Figure 1-1 Front of the computer Figure 1-2 System unit conf.
1.2 System Unit Block Diagram 1 Hardware Overview 1.2 System Unit Block Diagram Figure 1-3 is a block diagram of the system unit. Internal Touch Pad Figure 1-3 System unit block diagram Satellite M30-.
1 Hardware Overview 1.2 System Unit Block Diagram The system unit is composed of the following m ajor components: Processor Intel Banias Processor 1.40GHz • • • • – Processor core speed: 1.40GHz (Performance Mode at 1.35V) and 1.20GHz (Battery Optimized Mode at 0.
1.2 System Unit Block Diagram 1 Hardware Overview Memory Two memory slots are provided. Expansion up to 2GB (2,048MB) is available. Supports DDR CL2/2.
1 Hardware Overview 1.2 System Unit Block Diagram PC Card Controller Gate Array One YEBISU-SS gate array is used. • • • • This gate array has the following functions and components. – PCI interface (PCI Revision2.2) – CardBus/PC Card controller (Yenta2 Version2.
1.2 System Unit Block Diagram 1 Hardware Overview GPU Controller One nVIDIA NV34M chip is used. The GPU controller incorporates graphics accelerator, video accelerator.
1 Hardware Overview 1.2 System Unit Block Diagram One TMP87PM48U chip is used. • • • • • • • • • This controller controls the power sources.
1.2 System Unit Block Diagram 1 Hardware Overview Sensor Thermal Sensor: One ADM1032AR chip is used. • • LCD Sensor: One NRS-701-1015T is used.
1 Hardware Overview 1.3 3.5-inch Floppy Disk Drive (USB External) 1.3 3.5-inch Floppy Disk Drive (USB External) The 3.5-inch USB FDD is a thin, high-performance reliable drive that supports 720KB and 1.44MB. The FDD is shown in figure 1-4. The specifications for the FDD are listed in Table 1-1.
1.4 2.5-inch Hard Disk Drive 1 Hardware Overview 1.4 2.5-inch Hard Disk Drive The removable HDD is a random access non-volatile storage device. It has a non-rem ovable 2.5-inch magnetic disk and mini-W inchester type magnetic heads. The computer supports a 40GB, 60GB and 80GB HDD.
1 Hardware Overview 1.4 2.5-inch Hard Disk Drive Parameter Specifications HITACHI GBC000Z810 HITACHI GBC000014810 TOSHIBA HDD2188B Outline Width (mm) 69.85 ± 0.25 69.85 ± 0.25 69.85 dimensions Height (mm) 9.5 ± 0.25 9.5 ± 0.25 9.5 Depth (mm) 100 ± 0.
1.4 2.5-inch Hard Disk Drive 1 Hardware Overview Specifications Parameter HITACHI GBC000Z810 HITACHI GBC00014810 TOSHIBA HDD2188B Storage size (formatted) 80GB 80GB Speed (RPM) 4200 5400 4200 Data transfer speed 350 typ 450 max 175.0-341.78 (Mbits/s) Interface transfer rate (MB/s) 100 max.
1 Hardware Overview 1.5 CD-RW/DVD-ROM Drive 1.5 CD-RW/DVD-ROM Drive This drive is a combination of DVD-ROM and CD-R/RW Drive. . It is full-size and runs either 12cm (4.
1.6 DVD-R/RW 1 Hardware Overview 1.6 DVD-R/RW A full-size DVD-R/-RW drive module lets you reco rd data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed, CD-ROMs at maximum 24 speed and CD-Rs at maximum 16 speed.
1 Hardware Overview 1.6 DVD-R/RW Table -4 DVD-R/RW drive specifications Item Toshiba SD-R6112 ATAPI Burst (MB/sec) 33.3 (Ultra DMA mode 2) 16.6 (PIO Mode 0 to 4, Multi word DMA mode 0 to 2) Average ac.
1.7 DVD-Multi (CD-R/RW DVD-RAM/R/RW) Drive 1 Hardware Overview 1.7 DVD-Multi (CD-R/RW DVD-RAM/R/RW) Drive This drive is a combination of CD-R/RW, DVD-R/RW and DVD-RAM Drive. It is full-size and runs either 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor.
1 Hardware Overview 1.7 DVD-Multi (CD-R/RW DVD-RAM/R/RW) Drive Table 1-5 DVD-Multi drive specifications (2/2) Item TEAC G8CC00013210 Matsushita G8CC00019210 Speed (Write) CD-R CD-RW DVD-R DVD-RW DVD-RAM 16x max.(ZCLV) 10x (CLV) 2x (CLV) 1x (CLV) 2x (ZLV) 16x (ZoneCLV) 8x (CLV) 2x (CLV) 1x (CLV) 2x (ZCLV) (4.
1.8 Keyboard 1 Hardware Overview 1.8 Keyboard The keyboard is mounted 85(US)/86(UK) keys that consist of character key and control key, and in conformity with JIS. The keyboard is connected to mem brane connector on the system board and controlled by the keyboard controller.
1 Hardware Overview 1.9 TFT Color Display 1.9 TFT Color Display The TFT color display consists of 15.4-inch WXGA LCD module and FL inverter board. 1.9.1 LCD Module A high-resolution external monitor connected to the computer can display up to 2048(H) × 1536(V), at 16M colors.
1.9 TFT Color Display 1 Hardware Overview Table 1-6 LCD module specifications (2/5) Specifications Item 15.4-inch WXGA (G33C0001F110) Number of Dots 1,280 (W) x 800 (H) Dot spacing (mm) 0.25875 (H) x 0.25875 (V) Display range (mm) 332.16(H) x 207.6(V) Table 1-6 LCD module specifications (3/5) Specifications Item 15.
1 Hardware Overview 1.9 TFT Color Display 1.9.2 FL Inverter Board The FL inverter board supplies a high frequency current to illuminate the LCD module FL. Table 1-7 lists the FL inverter board specifications. Table 1-7 FL inverter board specifications Item Specifications Voltage (V) DC 5 Input Power (W) 7 Voltage (V) 750 Current (mA) 6.
1.10 Power Supply 1 Hardware Overview 1.10 Power Supply The power supply supplies many different voltages to the system board and perform s the following functions: 1.
1 Hardware Overview 1.10 Power Supply Table 1-8 Power supply output rating (1/2) Name Voltage (V) Use PPV 1.468-0.748 CPU MCH1R2- P1V 1.2 Odem PTV 1.075 CPU, ADM1032, Odem, ICH4-M 2R5-B2V 2.5 Odem, SDRAM 2R5-P2V 2.5 NV34 1R25-B1V 1.25 SDRAM PGV 1.2-1.
1.10 Power Supply 1 Hardware Overview Table 1-8 Power supply board output rating (2/2) Name Voltage (V) Use S5V 5 OZ168 MCV 5 PSC A4R7-P4V 4.7 STAC9750, MIC CDA4R7-E4V 4.
1 Hardware Overview 1.11 Batteries 1.11 Batteries The computer has three types of batteries as follows: Main battery pack RTC battery The battery specifications are listed in Table 1-9. Table 1-9 Battery specifications Battery name Material Output v oltage Capacity Main battery Lithium-Ion (6-cell) 10.
1.11 Batteries 1 Hardware Overview 1.11.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The microprocessor controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer.
1 Hardware Overview 1.11 Batteries 1-32 Satellite M30-35 Maintenance Manual (960-455) 1.11.3 RTC battery The RTC battery provides power to keep the current date, time and other setup information in memory while the com puter is turned off. Table 1-11 lists the charging time and data preservation period of the RTC battery.
Chapter 2 Troubleshooting Procedures.
2 Troubleshooting Procedures 2-ii Satellite M30-35 Maintenance Manual (960-455).
2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ...........................................
2 Troubleshooting Procedures Procedure 1 External Monitor Check ............................................................ 2-40 Procedure 2 Diagnostic Test Program Execution Check .............................. 2-40 Procedure 3 Connector and Cable Check.
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart ............................................................................ 2-3 Figure 2-2 A set of tool for debug port test ...................................................
2 Troubleshooting Procedures 2-vi Satellite M30-35 Maintenance Manual (960-455).
2.1 Troubleshooting 2 Troubleshooting Procedures 2 2.1 Troubleshooting Chapter 2 describes how to determine if a Fi eld Replaceable Unit (FRU) in the com puter is causing the computer to malfunction. The FRUs covered are: 1. Power supply 5. Keyboard 9.
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide fo r determining which troubleshooting procedures to execute.
2.2 Troubleshooting Flowchart 2 Troubleshooting Procedure s Figure 2-1 Troubleshooting flowchart (1/2) Satellite M30-35 Main tenance Manual (960-455) 2-3.
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (2/2) 2-4 Satellite M30-35 Maintenan ce Manual (960-455).
2.2 Troubleshooting Flowchart 2 Troubleshooting Procedure s If the diagnostics program cannot detect an erro r, the problem may be intermittent. The Running Test program should be executed severa l times to isolate the problem .
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2.3 Power Supply Troubleshooting The power supply controls many functions and components. To determ ine if the power supply is functioning properly, star t with Procedure 1 and continue with the other Procedures as instructed.
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Table 2-2 DC IN icon DC IN icon Power supply status Lights blue DC power i s being supplied from the AC adapter.
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN icon blinks orange.
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Check 1 Convert the DC IN icon blink patt ern into the hexadecimal error code and compare it to the tables below.
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Check 1 Compare the patterns in the hexadeci mal error code to the tables below. DC IN Error code Meaning 10h AC Adaptor output voltage is over 16.5 V. 11h Advanced Port Replicator output voltage is over 16.
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 1R8-C1V output Error code Meaning 60h 1R8-C1V voltage is over 2.16 V, w hen the computer is powered on/ off. 61h 1R8-C1V voltage is 1.53 V or under , when the computer is p owered on. 62h 1R8-C1V voltage is 1.
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting E3V output Error code Meaning A0h E3V voltage is over 3.96 V, w hen the computer is powered on/off. A1h E3V voltage is 2.81 V or under, when the computer is powered on. A2h E3V voltage is 2 .
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 1R25-P1V output Error code Meaning D0h 1R25-P1V voltage is ove r 1.50 V, when the computer is powered on/off. D1h 1R25-P1V voltage is 1.06 3 V or under, when the computer i s powered on.
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 3 Connection Check The power supply wiring diagram is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from the wall outlet.
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Procedure 4 Charge Check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the pow er. If you cannot turn on the power, go to Procedure 5.
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 5 Replacement Check The system board processor module m ay be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures .
2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2.4 System Board Troubleshooting This section describes how to determine if the system board is defective or not. Start with Procedure 1 and continue with the other proced ures as instructed.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting Procedure 1 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it.
2.4 System Board Troubleshooting 2 Troubleshooting Procedures Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If error message (5) appears, go to th e Keyboard Troubleshooting Procedures in Section 2.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting Procedure 2 Debugging Port Check on Boot Mode Check the D port status by a debug port test. Th e tool for debug port test is shown below. Figure 2-2 A set of to ol for debug port test The test procedures are follows; 1.
2.4 System Board Troubleshooting 2 Troubleshooting Procedures 5. Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for starting D port into FDD and input “FD starting drive:>dport”.) The D port status is displayed in the following form; 6.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-4 Debugging port boot mode status (2/7) Debug Port Description 0098h Initialize USB Controller 0101h 0102h Verify Real Mode. If the CPU is in protected mode, turn on A20 and pulse the reset line, forcing a shutdown 0.
2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debugging port boot mode status (3/7) Debug Port Description 0129h Initialize the POST Memory Manager 012Ah Zero clear the first 512K of RAM 012Bh 012Ch Test 512K base address lines 012Eh Test the first 4MB of RAM.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting 0152h Table 2-4 Debugging port boot mode status (4/7) Debug Port Description 0154h 0155h 0157h 0158h Test for unexpected interru pts.
2.4 System Board Troubleshooting 2 Troubleshooting Procedures 0185h Configure all PnP ISA devices. 0186h Table 2-4 Debugging port boot mode status (5/7) Debug Port Description 0187h Configure motherboar d configurable devices. 0188h Initialize timeouts, key buffer, and soft reset flag.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting 01AEh Clear CMOS flags for post. 2-26 Satellite M30-35 Main tenance Manual (960-455).
2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debugging port boot mode status (6/7) Debug Port Description 01B0h Check for errors. 01B1h 01B2h Change status bits in CMOS and/or the BIOS data area to reflect the fact that POST is complete.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-4 Debugging port boot mode status (7/7) Debug Port Description 01D7h 01D8h 20FFh Try to boot with INT 19h.
2.4 System Board Troubleshooting 2 Troubleshooting Procedures Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Di agnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more inform ation on how to perform these tests.
2 Troubleshooting Procedures 2.4 System Board Troubleshooting Procedure 4 Replacement Check The system board connectors may be disconnect ed. Disassemble the com puter following the steps described in Chapter 4, Replacement Procedures and perform Check 1.
2.5 FDD Troubleshooting 2 Troubleshooting Procedures 2.5 FDD Troubleshooting This section describes how to determine if the FDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required.
2 Troubleshooting Procedures 2.5 FDD Troubleshooting Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation about th e diagnostics test procedures.
2.5 FDD Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connector Check and Replacement Check The 3.5inch FDD is connected to the System Board via USB port. Check 1 Make sure the USB cable is securely connected to the FDD. Also, make sure the USB cable of the FDD is securely connected to the system board.
2 Troubleshooting Procedures 2.6 HDD Troubleshooting 2.6 HDD Troubleshooting This section describes how to determine if the HDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required.
2.6 HDD Troubleshooting 2 Troubleshooting Procedures Procedure 2 Partition Check Insert the Toshiba MS-DOS system di sk and restart the computer with U key holding down. Perform the following checks: Check 1 Type C : and press Enter . If you cannot change to drive C, go to Check 2.
2 Troubleshooting Procedures 2.6 HDD Troubleshooting Procedure 3 Format Check The computer’s HDD is formatted using the low level format program and the MS-DOS FORMAT program. To format the HDD, start with Check 1 below and perform the other steps as required.
2.6 HDD Troubleshooting 2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program.
2 Troubleshooting Procedures 2.6 HDD Troubleshooting Procedure 5 Connector Check and Replacement Check The HDD may be disconnected, or the HDD or the system board may be dam aged.
2.7 Keyboard Troubleshooting 2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting Procedure 2 Connector and Replacement Check The keyboard, PAD I/F and PAD Switch may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: 1.
2.8 Display Troubleshooting 2 Troubleshooting Procedures 2.8 Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures 2.8 Display Troubleshooting Procedure 3 Connector and Cable Check The LCD Module is connected to the system board by an LCD/FL cable. The FL inverter board is also connected to the system board by an LCD/FL cable. And the FL is connected to the FL inverter board by the HV cable.
2.8 Display Troubleshooting 2 Troubleshooting Procedures Procedure 4 Replacement Check The FL, FL inverter board, LCD module, and system board are connected to display circuits.
2 Troubleshooting Procedures 2.9 Optical Drive Troubleshooting 2.9 Optical Drive Troubleshooting This section describes how to determine if th e Optical Drive is func tioning properly. Perform the steps below starting with Procedure 1 and co ntinue with the other procedures as required.
2.9 Optical Drive Troubleshooting 2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The Optical Drive is connected to the syst em board.
2 Troubleshooting Procedures 2.10 Modem Troubleshooting 2.10 Modem Troubleshooting This section describes how to determine if the computer' s modem is functioning properly. Perform the steps below starting with Procedure 1 and continui ng with the other procedures as required.
2.10 Modem Troubleshooting 2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The Modem is installed as a modem daughter ca rd (MDC). If the modem m alfunctions, there may be a bad connection between the MDC a nd the System Board.
2 Troubleshooting Procedures 2.12 LAN Troubleshooting 2.11 LAN Troubleshooting This section describes how to determine if the computer's LAN is functioning properly. Perform the steps below starting with Procedure 1 and continui ng with the other procedures as required.
2.12 Wireless LAN Troubleshooting 2 Troubleshooting Procedures 2.12 Wireless LAN Troubleshooting This section describes how to determine if the computer's W ireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
2 Troubleshooting Procedures 2.12 Wireless LAN Troubleshooting Procedure 2 Antennas' Connection Check The wireless LAN wiring diagram is shown below: Any of the connections may be disconnected.
2.12 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Procedure 3 Antenna Check Check 1 Use an antenna test cable to check the antennas' connection. Follow the steps below: 1. Remove the wireless LAN slot cover and lift it off. Refer to Chapter 4, Replacement Procedures , for detailed steps of disassembling.
2 Troubleshooting Procedures 2.12 Wireless LAN Troubleshooting Procedure 4 Replacement Check The wireless LAN board is connected to the pow er board and the system board.
2.13 Sound Troubleshooting 2 Troubleshooting Procedures 2.13 Sound Troubleshooting This section describes how to determine if the computer's sound functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
2 Troubleshooting Procedures 2.13 Sound Troubleshooting Procedure 2 Connector Check The sound function wiring diagram is shown below: Any of the connections may be disconnected.
2.13 Sound Troubleshooting 2 Troubleshooting Procedures Procedure 3 Replacement Check Check 1 If the stereo speakers do not sound pr operly, they may be defective or damaged. Replace them with new ones. If the stereo speakers still do no t work properly, go to Check 5.
2 Troubleshooting Procedures 2.14 SD Card Slot Troubleshooting 2.14 SD Card Slot Troubleshooting To check if the SD card/Smart Media slot is good or no good, follow the troubleshooting procedures below as instructed.
2.14 SD Card Slot Troubleshooting 2 Troubleshooting Procedures Satellite M30-35 Main tenance Manual (960-455) 2-57.
Chapter 3 Tests and Diagnostics.
3 Tests and Diagnostics 3-ii Satellite M30-35 Maintenance Manual (960-455).
3 Tests and Diagnostics Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ..............................................
3 Tests and Diagnostics 3-iv Satellite M30-35 Maintenance Manual (960-455) 3.23 System Configuration .............................................................................................. 3-47 3.23.1 Function Description ......................
3.1 The Diagnostic Test 3 Tests and Diagnostics 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test program to test the functions of the computer’s hardware modules. The Diagnostic Test Program is stored on the Diagnostic Disk.
3 Tests and Diagnostics 3.1 The Diagnostic Test You will need the following equipment to perform som e of the Diagnostic test programs. The Diagnostics Disk (all tests) A formatted working dis.
3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM. To start the DIAGNOSTIC TEST PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive and turn on the computer while pressing F key.
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 2. To execute the DIAGNOSTIC TEST MENU from the DIAGNOSTICS MENU, set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA Personal Computer XXXXXX DIAGNOSTICS Version X.
3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3. Select the test you want to execute and press Enter . When SYSTEM TEST is selected, the following message will appear: SYSTEM TEST XXXXXXX XXX DIAGNOSTIC TEST VX.
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 5. The following message will appear: ERROR STOP : YES/NO Selecting YES stops the test program when an error is found and displays the operati.
3.3 Subtest Names 3 Tests and Diagnostics 3.3 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No.
3 Tests and Diagnostics 3.3 Subtest Names Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 6 PRINTER 01 02 03 Ripple pattern Function Wrap around 7 ASYNC 06 07 FIR/SIR Point to poi.
3.4 System Test 3 Tests and Diagnostics 3.4 System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter .
3 Tests and Diagnostics 3.4 System Test Subtest 07 DMI read This subtest displays the information in the Flash-ROM in the following format. *** DMI Data Display Ver X.
3.4 System Test 3 Tests and Diagnostics 7. “Create DMIINFO TXT (Y/N) ?” is displayed. Press Y, then the DMI information (text data) is written to the Floppy disk, etc. Subtest 10 CPU Temperature This subtest checks the CPU temperature. When the subtest starts, the following message appears on the display.
3 Tests and Diagnostics 3.5 Memory Test 3.5 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter .
3.6 Keyboard Test 3 Tests and Diagnostics 3.6 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter .
3 Tests and Diagnostics 3.6 Keyboard Test Subtest 04 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check. This test displays the response from the touch pad and touch pad switch.
3.6 Keyboard Test 3 Tests and Diagnostics Subtest 05 USB (Port 0, Port1) test This subtest checks USB. The USB TEST Module (ZD0003P01) and USB Cable (ZD0003P02) must be connected to the computer. The following message will appear. Select a port to test and press Enter .
3 Tests and Diagnostics 3.7 Display Test 3.7 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter .
3.7 Display Test 3 Tests and Diagnostics Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter .
3 Tests and Diagnostics 3.7 Display Test Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHH.
3.8 Floppy Disk Test 3 Tests and Diagnostics 3.8 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD. The contents of the floppy disk will be erased.
3 Tests and Diagnostics 3.8 Floppy Disk Test Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test.
3.9 Printer Test 3 Tests and Diagnostics 3.9 Printer Test To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The following messages will appear af ter selecting the Printer Test from the DIAGNOSTIC TEST MENU.
3 Tests and Diagnostics 3.9 Printer Test Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasize.
3.10 Async Test 3 Tests and Diagnostics 3.10 Async Test To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want to execute and press Enter .
3 Tests and Diagnostics 3.11 Hard Disk Test 3.11 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 01, 02, 03, 04, 06, 07,09, or 10 is executed.
3.11 Hard Disk Test 3 Tests and Diagnostics 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter . The following message will appear during each subtest.
3 Tests and Diagnostics 3.11 Hard Disk Test 3-26 Satellite M30-35 Maintenance Manual (960-455) Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder.
3.12 Real Timer Test 3 Tests and Diagnostics 3 3.12 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter .
3 Tests and Diagnostics 3.12 Real Timer Test Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increment.
3.13 NDP Test 3 Tests and Diagnostics 3.13 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen.
3 Tests and Diagnostics 3.14 Expansion Test 3.14 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE: To execute this subtest, the PC card wraparound connector is required.
3.15 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics 3.15 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD test, select 13 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK (ZA1217P01/P000204190) for CD-ROM and DVD-ROM TEST DISK TSD-1 for DVD-ROM.
3 Tests and Diagnostics 3.16 LAN test 3.16 LAN test To execute the LAN test, select 14 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The LAN test contains one subtest. Subtest 01 LAN MAC ADDRESS DISPLAY This subtest reads MAC ADDRESS and displays it.
3.17 Error Code and Error Status Names 3 Tests and Diagnostics 3.17 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test.
3 Tests and Diagnostics 3.17 Error Code and Error Status Names Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name ASYNC 01 02 04 08 10 20 40 50 60 70 80 DSR On.
3.17 Error Code and Error Status Names 3 Tests and Diagnostics Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name Expansion C1 C2 C3 C4 C5 C6 C7 C8 CB CD Addre.
3 Tests and Diagnostics 3.18 Hard Disk Test Detail Status 3.18 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight-digit number.
3.18 Hard Disk Test Detail Status 3 Tests and Diagnostics Table 3-4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error.
3 Tests and Diagnostics 3.19 Head Cleaning 3.19 Head Cleaning 3.19.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.19.
3.20 Log Utilities 3 Tests and Diagnostics 3.20 Log Utilities 3.20.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or output the data to a printer.
3 Tests and Diagnostics 3.20 Log Utilities 3.20.2 Operations 1. Selecting 5 and pressing Enter in the DIAGNOSTIC MENU, logs error information into RAM or onto a floppy disk.
3.21 Running Test 3 Tests and Diagnostics 3.21 Running Test 3.21.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02 and 04) 3. Display test (subtest 01) 4.
3 Tests and Diagnostics 3.22 Floppy Disk Drive Utilities 3.22 Floppy Disk Drive Utilities 3.22.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a floppy disk drive.
3.22 Floppy Disk Drive Utilities 3 Tests and Diagnostics 3.22.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2.
3 Tests and Diagnostics 3.22 Floppy Disk Drive Utilities 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a message sim ilar to the one below: Insert source disk into drive A: Press any key when ready.
3.22 Floppy Disk Drive Utilities 3 Tests and Diagnostics 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display will go to step (h).
3 Tests and Diagnostics 3.22 Floppy Disk Drive Utilities 3-46 Satellite M30-35 Maintenance Manual (960-455) (k) The following message will appear. To finish the dump, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear.
3.23 System Configuration 3 Tests and Diagnostics 3 3.23 System Configuration 3.23.1 Function Description The System Configuration program contains th e following configuration information for the computer: 1. Processor Type 2. VGA Controller 3. MS-DOS Version 4.
3 Tests and Diagnostics 3.23 System Configuration 3.23.2 Operations Selecting 8 from the DIAGNOSTIC MENU and pressing Enter displays the following system configuration: System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX * - VGA Controller = XXXXXX * - MS-DOS Version = V7.
3.24 Wireless LAN Test Program (Calexico) 3 Tests and Diagnostics 3.24 Wireless LAN Test Program (Calexico) This section describes how to perform the wireless LAN transm itting-receiving test with the test program.
3 Tests and Diagnostics 3.25 Wireless LAN Test Program (Atheros 11b/g or 11a/b/g) 3.25 Wireless LAN Test Program (Atheros 11b/g or 11a/b/g) This section describes how to perform the wireless LAN transm itting-receiving test with the test program.
3.25 Wireless LAN Test Program (Atheros 11b/g or 11a/b/g) 3 Tests and Diagnostics Setting the responder machine NOTE: Release the write-protection of the floppy disk for the test. Insert a floppy disk containing the test program into the floppy disk drive of the responder machine and turn on the responder machine.
3 Tests and Diagnostics 3.25 Wireless LAN Test Program (Atheros 11b/g or 11a/b/g) When the tester machine has passed the test, "OK" m essage will appear in the tester machine. Press Enter to return to the main menu. When the tester machine has not passed the test, "NG" m essage will appear in the tester machine.
3.26 Sound/LAN/Modem Test Program 3 Tests and Diagnostics 3.26 Sound/LAN/Modem Test Program This section describes how to perform the Sound/LAN/Modem test with the test program . Insert the Test program disk in the floppy disk drive and turn on the power.
3 Tests and Diagnostics 3.26 Sound/LAN/Modem Test Program Subtest 01 Microphoned recording & play [Recording & play test !] This subtest checks the function of the CODEC A/D D/A converter. Both the microphone and headphone terminals can be checked at the sam e time.
3.26 Sound/LAN/Modem Test Program 3 Tests and Diagnostics Subtest 02 LAN This subtest checks the operation of mini-PCI I/F by the loopback in the chip.
3 Tests and Diagnostics 3.26 Sound/LAN/Modem Test Program After a few seconds, the following message will appear: ...Press Key (Y = OK, N =NG) If you hear the modem sou n d from the speakers, press Y , otherwise, press N . NOTE : The menu displayed by your computer may be slightly different from the one shown above.
3.27 IEEE1394 test program 3 Tests and Diagnostics 3.27 IEEE1394 test program This section describes how to perform the IEEE1394 test with the test program. NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test.
3 Tests and Diagnostics 3.27 IEEE1394 test program 3-58 Satellite M30-35 Maintenance Manual (960-455).
Chapter 4 Replacement Procedures.
4 Replacement Procedures 4-ii Satellite M30-35 Maintenance Manual (960-455).
4 Replacement Procedures Chapter 4 Contents 4.1 General .................................................................................................................... ... 4-1 4.2 Battery Pack .....................................................
4 Replacement Procedures 4.27 Sensor/Switch Board................................................................................................ 4-69 4.28 LCD Cable/Wireless LAN Antenna/Hinge ..........................................................
4 Replacement Procedures Figure 4-24 Removing the Touch pad holder .................................................................. 4-45 Figure 4-25 Removing the CD-key assembly ................................................................. 4-46 Figure 4-26 Removing the System board (1) .
4 Replacement Procedures 4-vi Satellite M30-35 Maintenance Manual (960-455) Figure 4-56 Replacing TMD fluorescent lamp (WXGA) (6) .......................................... 4-83 Figure 4-57 Replacing TMD fluorescent lamp (WXGA) (7) ...................
4.1 General 4 Replacement Procedures 4 Replacement Procedures 4.1 General This section explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order to remove others.
4 Replacement Procedures 4.1 General Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1) Always use the genuine battery that is authorized by Toshiba or compatible with the unit.
4.1 General 4 Replacement Procedures Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassem bly steps. Begin each procedure by removing the AC adapter and the battery pack as instructed in this section: 1.
4 Replacement Procedures 4.1 General Disassembly Procedures The computer has two basic types of cable connectors: • Pressure Plate Connectors • Coaxial Cable Connectors • Normal Pin Connectors T.
4.1 General 4 Replacement Procedures Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts.
4 Replacement Procedures 4.1 General Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose.
4.1 General 4 Replacement Procedures Color of Screw Shaft To avoid mistakes on the screw length, screw shafts are colored as follows: Even number length screw: brown Odd number length screw: white Special length screw: blue Screws whose lengths are indicated to one or more decimal places such as 2.
4 Replacement Procedures 4.2 Battery Pack 4.2 Battery Pack Removing the Battery Pack To remove the battery pack, follow the steps below and refer to figure 4-1. CAUTION: When handling battery packs, be careful not to short circuit the terminals. Also do not drop, hit or apply impact; do not scratch, break, twist or bend the battery pack.
4.2 Battery Pack 4 Replacement Procedures Installing the Battery Pack To install the battery pack, follow the steps below and refer to figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of.
4 Replacement Procedures 4.3 PC Card 4.3 PC Card Removing the PC Card To remove the PC card, follow the steps below and refer to figure 4-2. CAUTION: Before you remove a PC card, refer to the card's documentation and your operating system documentation for proper procedures and precautions.
4.3 PC Card 4 Replacement Procedures Installing the PC Card To install the PC card, follow the steps below and refer to figure 4-2. 1. Make sure the eject button does not stick out.
4 Replacement Procedures 4.4 SD Card 4.4 SD Card Removing the SD Card To remove the SD card, follow the steps below and refer to figure 4-3. CAUTION: Before you remove the SD card, refer to the card's documentation and to your operating system documentation for proper procedures and precautions.
4.5 HDD 4 Replacement Procedures 4.5 HDD CAUTION : When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. HDD Removing the HDD To remove the HDD, follow the steps below and refer to figures 4-4 and 4-5. 1. Turn the computer upside down.
4 Replacement Procedures 4.5 HDD 3. Push the tab of the HDD pack to the direction of the arrow and remove the HDD pack. Be careful not to damage the connector. NOTE: The following steps describe how to disassemble the HDD pack; however, do not disassemble if the HDD is working properly.
4.5 HDD 4 Replacement Procedures Installing the HDD To install the HDD, follow the steps below and refer to figures 4-4 and 4-5. CAUTION: Do not hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Install the HDD to the aluminum laminate .
4 Replacement Procedures 4.6 Optical Drive 4.6 Optical Drive Removing the Optical Drive To remove the optical drive, follow the steps below and refer to figures 4-6 and 4-7. CAUTION: Do not apply excessive force to the top of an optical drive. 1. Remove the following screws securing the optical drive .
4.6 Optical Drive 4 Replacement Procedures 3. Remove the following screws securing the plastic frame . • M2 × 3C S-FLAT HEAD screw × 4 • Stepping screw × 1 Opt ica l Dr iv e Pl astic frame M2 .
4 Replacement Procedures 4.6 Optical Drive Installing the Optical drive To install the optical drive, follow the steps below and refer to figures 4-6 and 4-7. 1. Seat the plastic frame on the side of the optical drive, and secure it with the following s crews .
4.7 Memory module/ Modem Daughter Card 4 Replacement Procedures 4.7 Memory module/ Modem Daughter Card CAUTION: The power of the computer must be turned off when you remove the memory module. Removing a memory module with the power on risks damaging the module or the computer itself.
4 Replacement Procedures 4.7 Memory module/ Modem Daughter Card Installing the memory module To install the memory m odule, confirm that the computer is in boot m ode. Then follow the steps below and refer to figures 4-8. 1. Insert the memory module into the connector of the computer slantwise (terminal side first) and press it to connect firmly.
4.7 Memory module/ Modem Daughter Card 4 Replacement Procedures 4.7.2 Modem Daughter Card Removing the Modem Daughter Card To remove the modem daughter card, follow the steps below and refer to figure 4-9. 1. Remove the following screws securing the m odem daughter card.
4 Replacement Procedures 4.7 Memory module/ Modem Daughter Card Installing the Modem Daughter Card To install the modem daughter card, follow the steps below and refer to figures 4-9. 1. Connect the modem cable to CN1 on the modem daughter card. 2. Connect the modem daughter card to the connector PJ3000 on the system board.
4.8 Wireless LAN board 4 Replacement Procedures 4.8 Wireless LAN board CAUTION: The power must be turned off when you remove the wireless LAN board. Removing the wireless LAN board with the power on risks damaging the card or the computer itself. Never press hard or bend the wireless LAN board.
4 Replacement Procedures 4.8 Wireless LAN board 4-24 Satellite M30-35 Ma intenance Manual (960-455) Installing the wireless LAN board To install the wireless LAN board, follow the steps below and refer to figure 4-10.
4 Replacement Procedures 4.9 Keyboard 4 Replacement Procedures 4.9 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to figures 4-11 to 4-12.
4.9 Keyboard 4 Replacement Procedures 4. Lift the upper side of the keyboard out and turn it’s face down on the palm rest. 5. Remove the following screw securing the keyboard support plate and remove the keyboard support plate. • M2.5 × 8B FLAT HEAD screw × 1 M2.
4 Replacement Procedures 4.9 Keyboard Installing the Keyboard To install the keyboard, follow the steps below and refer to figures 4-11 to 4-12. 1. Place the keyboard face down on the palm rest. 2. Connect the keyboard cable to the connector PJ3200 on the system board.
4.10 Switch cover ASSY/Switch membrane 4 Replacement Procedures 4.10 Switch cover ASSY/Switch membrane Removing the Switch cover ASSY/Sw itch membrane To remove the Switch cover ASSY/Switch mem brane, follow the steps below and refer to figure 4-13 and 4-14.
4 Replacement Procedures 4.10 Switch cover ASSY/Switch membrane 2. Pull up the insulator . 3. Disconnect the switch membrane cable from the connector PJ7001 on the system board. 4. Remove the following screws fixing the switch membrane . • M2.5 × 4B FLAT HEAD screw × 2 5.
4.10 Switch cover ASSY/Switch membrane 4 Replacement Procedures Installing the Switch cover ASSY/Sw itch membrane To install the Switch cover ASSY/Switch membrane, fo llow the steps below and refer to figure 4-13 and 4-14. 1. Place the switch membrane with the right side under the guides and secure it with the following screws .
4 Replacement Procedures 4.11 Display Assembly 4.11 Display Assembly Removing the Display Assembly To remove the display assembly, follow the steps below and refer to figures 4-15 to 4-17. 1. Turn the computer face down, and remove the following screws .
4.11 Display Assembly 4 Replacement Procedures 2. Turn the computer face up and open the display panel. 3. Remove the following screws securing the display assem bly. • M2.5 × 6B FLAT HEAD screw × 3 • M2.5 × 8B FLAT HEAD screw × 1 4. Disconnect the LCD cable from the connector PJ5600 on the system board.
4 Replacement Procedures 4.11 Display Assembly 8. Remove the display assembly from the base assembly. Display asse mbly Figure 4-17 Removing the display assembly (3) NOTE: When removing the display assembly, be careful not to damage any cables.
4.11 Display Assembly 4 Replacement Procedures Installing the Display Assembly To install the display assembly, follow the steps below and refer to figures 4-15 to 4-17. 1. Install the display assembly on the base assembly. NOTE : When installing the display assembly, be careful not to pinch or damage any cables.
4 Replacement Procedures 4.12 Touch Pad Button 4.12 Touch Pad Button Removing the Touch Pad Button To remove the touch pad button, follow the steps below and refer to figure 4-18. 1. Remove the following screws fixing the touch pad button. • M2.5 × 4 Tapping screw × 3 2.
4.13 Microphone 4 Replacement Procedures 4.13 Microphone Removing the Microphone To remove the Microphone, follow the steps below and refer to figures 4-19 and 20. 1. Remove the microphon e from the guide. Micr op ho n e Figure 4-19 Removing the microphone 2.
4 Replacement Procedures 4.13 Microphone Installing the Microphone To install the Microphone, follow the steps below and refer to figures 4-19 and 20. 1. Pass the microphone cable from the front to the back. 2. Set the microphone , putting the hole in the guide.
4.14 Touch Pad 4 Replacement Procedures 4.14 Touch Pad Removing the Touch Pad To remove the touch pad, follow the steps below and refer to figures 4-21. 1. Disconnect the touch pad flexible cable from the connector PJ3201 on the system board. 2. Remove the following screws securing the touch pad.
4 Replacement Procedures 4.14 Touch Pad Installing the Touch Pad To install the touch pad, follow the steps below and refer to figures 4-21. 1. Connect the touch pad flexible cable to the connector on the touch pad. 2. Install the touch pad and secure it with the following screws .
4.15 RTC Battery 4 Replacement Procedures 4.15 RTC Battery WARNING: When replacing the RTC battery, be sure to use genuine batteries or replacement batteries authorized by Toshiba. Installing the wrong battery could cause a battery explosion or other damage.
4 Replacement Procedures 4.15 RTC Battery Removing the RTC Battery To remove the RTC battery, follow the steps below and refer to figure 4-22. 1. Peel off the insulator . 2. Disconnect the RTC battery cable from the connector PJ8490 on the system board.
4.16 Sound Board/Touch Pad holder 4 Replacement Procedures 4.16 Sound Board/Touch Pad holder 4.16.1 Sound Board Removing the Sound Board To remove the sound board, follow the steps below and refer to figure 4-23. 1. Remove the following screw and the sound board .
4 Replacement Procedures 4.16 Sound Board/Touch Pad holder Installing the Sound Board To install the sound board, follow the steps below and refer to figure 4-23. 1. Connect the sound board I/F cable to the connector on the sound board and secure it with the insulator .
4.16 Sound Board/Touch Pad holder 4 Replacement Procedures 4.16.2 Touch Pad holder Removing the Touch Pad holder To remove the touch pad holder, follow the steps below and refer to figures 4-24. 1. Disconnect the sound board I/F cable from the connector PJ7002 on the system board.
4 Replacement Procedures 4.17 CD-Key assembly 4.17 CD-Key assembly Removing the CD-Key assembly To remove the CD-key assembly, follow the steps below and refer to figures 4-25. 1. Disconnect the CD-key flexible cable from the connector PJ7000 on the system board.
4.18 System Board 4 Replacement Procedures 4.18 System Board Removing the System Board To remove the system board, follow the steps below and refer to figures 4-26 and 4-27. 1. Peel off the glass tape and disconnect the RGB cable from the connector PJ5621 on the system board.
4 Replacement Procedures 4.18 System Board 7. Remove the following screws securing the system board. • M2.5 × 6B FLAT HEAD screw × 1 8. Lift up the right side of the system board and remove it.
4.18 System Board 4 Replacement Procedures Satellite M30-35 Maintenan ce Manual (960-455) 4-49 Installing the System Board To install the system board, follow the steps below and refer to figures 4-26 and 27. 1. Install the system board from the left side.
4 Replacement Procedures 4.19 CPU 4 Replacement Procedures 4.19 CPU Removing the CPU To remove the CPU, follow the steps below and refer to figures 4-28 and 4-29. CAUTION: 1) The CPU can become very hot during operation. Be sure to let it cool before starting repair work.
4.19 CPU 4 Replacement Procedures CAUTION: Silicon grease is applied between the fin and the CPU. When removing the fin, be careful not to damage the CPU under the fin.
4 Replacement Procedures 4.19 CPU Installing the CPU To install the CPU, follow the steps below and refer to figures 4-28 to 4-30. 1. Make sure the cam is in the open position. 2. Seat the CPU in the CPU socket. Make sure the position is exact to avoid damaging pins on the CPU.
4.20 Speaker 4 Replacement Procedures 4.20 Speaker Removing the Speaker To remove the speaker, follow the steps below and refer to figures 4-31 and 4-32. 1. Remove the following screws and peel the insulator . • M2.5 × 6B FLAT HEAD screw × 4 • M2.
4 Replacement Procedures 4.20 Speaker 2. Remove the following screw and cable holder . • M2.5 × 4B FLAT HEAD screw × 1 M2.5 × 4B FLA T HEAD Cabl e holder Figure 4-32 Removing the cable holder 3. Remove both the speakers . Installing the Speaker To install the speaker, follow the steps below and refer to figures 4-31 to 4-32.
4.21 Fan 4 Replacement Procedures 4.21 Fan Removing the Fan To remove the fan, follow the steps below and refer to figure 4-33. 1. Remove the following screws securing the fan. • M2.5 × 6B FLAT HEAD screw × 1 (lower right side) 2. Remove the fan .
4 Replacement Procedures 4.22 USB Board/DC-IN jack/Network jack 4.22 USB Board/DC-IN jack/Network jack Removing the USB Board/DC-IN jack/Network jack To remove the USB board/DC-IN jack/network jack, follow the steps below and refer to figure 4-34. 1. Remove the following screw securing the USB board.
4.22 USB Board/DC-IN jack/Network jack 4 Replacement Procedures Installing the USB Board/DC-IN jack/Network jack To install the USB board/DC-IN jack/network jack, follow the steps below and refer to the figure 4-34. 1. Connect the DC-IN jack cable to the connector CN1 on the power board and Install the DC-IN jack .
4 Replacement Procedures 4.23 RGB board/Power board 4.23 RGB board/Power board Removing the RGB board/Power board To remove the RGB board/Power board, follow the steps below and refer to figures 4-35 to 4-37. 1. Remove the following screws and battery plate .
4.23 RGB board/Power board 4 Replacement Procedures 4. Remove the following screws and power board . • M2.5 × 6 Tapping screw × 2 M2. 5 × 6 Ta ppin g B atte ry c ab le Wir eless LA N ca ble ( wh ite) Wir eless LA N ca ble ( bla ck ) Figure 4-37 Removing the power board 5.
4 Replacement Procedures 4.23 RGB board/Power board Installing the RGB board/Power board To install the RGB board/Power board, follow the steps below and refer to figures 4-35 to 4- 37. 1. Connect the battery cable to the connector CN4 on the power board.
4.24 Display Mask 4 Replacement Procedures 4.24 Display Mask Removing the Display Mask To remove the display mask, follow the steps below and refer to figures 4-38. 1. Remove the two mask seals at the lower part of the display mask. 2. Remove the four rubber masks at the top of the display mask.
4 Replacement Procedures 4.24 Display Mask Installing the Display Mask To install the display mask, follow the steps below and refer to figures 4-38. 1. Place the display mask on the LCD module. 2. Engage the latches of the display mask. 3. Secure the display mask with the following screws .
4.25 FL Inverter 4 Replacement Procedures 4.25 FL Inverter Removing the FL Inverter To remove the FL inverter, follow the steps below and refer to figure 4-39. 1. Remove the following screw securing the FL inverter. • M2 × 4B S-FLAT HEAD screw × 1 2.
4 Replacement Procedures 4.25 FL Inverter Installing the FL Inverter To install the FL inverter, follow the steps below and refer to figure 4-39. 1. Connect the FL cable and the HV cable to the FL inverter. 2. Seat the FL inverter and stick the insulator on the FL inverter of the FL cable side.
4.26 LCD Module 4 Replacement Procedures 4.26 LCD Module NOTE: 1) Be careful not to apply pressure to the ICs along the edge of LCD module. The ICs are easily damaged. 2) For environmental reasons, do not throw away a malfunctioning LCD module (or FL).
4 Replacement Procedures 4.26 LCD Module 5. Disconnect the LCD cable from the connector on the back of the LCD and remove the LCD module . CAUTION : When removing the LCD cable, be careful not to damage the connector.
4.26 LCD Module 4 Replacement Procedures 6. Remove the following screws securing the two metal braces to the LCD m odule. • M2 × 3C S-FLAT HEAD screw × 4 Me t al br ace Me t al br ace M2 × 3C S -.
4 Replacement Procedures 4.26 LCD Module Installing the LCD Module To install the LCD module, follow the steps below and refer to figures 4-40 and 4-41. 1. Secure the two metal braces to the LCD module with the following screws . • M2 × 3C S-FLAT HEAD screw × 4 2.
4.27 Sensor/Switch Board 4 Replacement Procedures 4.27 Sensor/Switch Board Removing the Sensor/Switch Board To remove the sensor/switch board, make sure the com puter is in boot mode and powered off, follow the steps below and refer to figure 4-42. 1.
4 Replacement Procedures 4.28 LCD cable/Wireless LAN Antenna/Hinge 4.28 LCD cable/Wireless LAN Antenna/Hinge Removing the LCD cable/Wireless LAN Antenna To remove the LCD cable/wireless LAN antenna, follow the steps below and refer to figures 4-43 to 4-49.
4.28 LCD cable/Wireless LAN Antenna/Hinge 4 Replacement Procedures 3. Peel off the four acetate tapes fixing the wireless LAN antenna cable. 4. Peel off the three copper sheets and the gasket fixing the wireless LAN antenna. 5. Peel off both the wireless LAN antennas and pull out the cables through the hole under the hinge cap.
4 Replacement Procedures 4.28 LCD cable/Wireless LAN Antenna/Hinge 6. Remove the hinge caps . 7. Remove the following screws fixing the hinges on the display cover. • M2.5 × 4B FLAT HEAD screw × 2 M2. 5 × 4B FL AT H E AD Hin ge ca p Figure 4-46 Removing the hinge cap 8.
4.28 LCD cable/Wireless LAN Antenna/Hinge 4 Replacement Procedures 9. Pull out the LCD cable . 10. Remove the following screws and circle plate . • M2 × 4B S-FLAT HEAD screw × 2 M2 × 4B S-FLA T HEAD Circle plate Figure 4-48 Removing the circle plate 11.
4 Replacement Procedures 4.28 LCD cable/Wireless LAN Antenna/Hinge Installing the LCD cable/Wireless LAN Antenna To install the wireless LAN antenna/Bluetooth antenna/display cover/speaker, follow the steps below and refer to figures 4-43 to 4-50. 1. Pass the LCD cable through the slot and guide.
4.28 LCD cable/Wireless LAN Antenna/Hinge 4 Replacement Procedures Satellite M30-35 Maintenan ce Manual (960-455) 4-75 10. Secure the wireless LAN antenna with the three copper sheets and the gasket . Standard for sticking position of copper sheets (right , left) The copper sheet shall not be over the edge of the wall of LCD cover .
4 Replacement Procedure 4.29 Fluorescent Lamp 4 4.29 Fluorescent Lamp This system uses LCD modules from the following suppliers. The procedure for replacing the fluorescent lamp is different for each LCD module. Refer to the appropriate procedure. Type Part No.
4.29 Fluorescent Lamp 4 Replacement Procedure 4.29.1 Replacing the 15.4-inch WXGA TMD Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign substance into the module.
4 Replacement Procedure 4.29 Fluorescent Lamp NOTE: 1) Be careful not to give any damage to the TAB. 2) The X-PCB insulation sheet should be left attached to the bezel, as it will be recycled. 3) The Y-PCB insulation sheet shall not be disposed after removed, as it will be recycled.
4.29 Fluorescent Lamp 4 Replacement Procedure 2. Removing screws 1) Spread out the insulation sheet without detaching from the side of bezel. 2) Remove the screws (left side, right side) in order as shown in the figure below. NOTE: Use a Philips screwdriver with type 0 bit to remove the screws.
4 Replacement Procedure 4.29 Fluorescent Lamp 3. Removing bezel 1) Turn the LCD module face up with the insulation sheets on it. 2) Release the latches of the bezel and frame. (five points on upper side, two points lower side) 3) Remove the double-sided adhesive tape on the bottom of the side of bezel, and remove the bezel.
4.29 Fluorescent Lamp 4 Replacement Procedure 4. Spreading out PCB 1) Spread out the X-PCB and Y-PCB horizontally in order. NOTE: Be careful not to damage the TAB.
4 Replacement Procedure 4.29 Fluorescent Lamp 5. Removing PCB-ASSY cell 1) Remove the PCB-ASSY cell from the backlight unit. 2) Remove the double-sided adhesive tape from the back of the cell. NOTE: 1) Remove the tape slowly not to break the cell. The cell and frame are glued by double-sided adhesive tape.
4.29 Fluorescent Lamp 4 Replacement Procedure Assembling the 15.4-inch WXGA TMD Fluorescent Lamp To assemble the 15.4-inch WXGA TMD fluorescent lam p, follow the steps below and refer to figures 4-56 to 4-61. 1. Checking backlight 1) Check the following items shown in the figure below.
4 Replacement Procedure 4.29 Fluorescent Lamp 2. Assembling PCB-ASSY cell 1) Remove the release paper of the double-sided tape at the upper of the backlight unit. 2) Light up the backlight. 3) Make sure there is no dust, alien substance or scratch on the backlight.
4.29 Fluorescent Lamp 4 Replacement Procedure 3. Folding and temporary fixing of TAB/PCB 1) Fold the X-TAB (X-PCB) and Y-TAB (Y-PCB) to the back of backlight unit. 2) Hook the X-PCB on the three latches on the back of frame. NOTE: Be careful not to damage the TAB.
4 Replacement Procedure 4.29 Fluorescent Lamp 4. Setting bezel 1) Hook the bezel on the five latches of the frame from the upper side. NOTE: 1) Make sure the GND-CU on the left side and lamp reflector shall be inside the bezel. 2) Be careful not to damage the TAB.
4.29 Fluorescent Lamp 4 Replacement Procedure 5. Fixing PCBs and bezel with screws 1) Tighten the left side with the screws in order shown in the figure below. 2) Tighten the right side with the screws in order shown in the figure below. NOTE: 1) Tighten the screws in order.
4 Replacement Procedure 4.29 Fluorescent Lamp 6. Sticking tapes and insulation sheets 1) Stick the Y-PCB insulation sheet and X-PCB insulation sheet in order. 2) Stick the two bezel tapes on the lower side (lamp side). 3) Stick the fixing tape for FL cable.
4.29 Fluorescent Lamp 4 Replacement Procedure 4.29.2 Replacing the 15.4-inch WXGA LG.Philips Fluorescent Lamp Disassembly of outside tape / Cover shield To disassemble the 15.4-inch WXGA LG.Philips fluorescent lam p, follow the steps below and refer to figures 4-62 to 4-65.
4 Replacement Procedure 4.29 Fluorescent Lamp Disassembly of Top case 1. Disassembly of Top Case CAUTION : Pressure or stress should not be given on Top Case and Gate COF.
4.29 Fluorescent Lamp 4 Replacement Procedure Disassembly of Source PCB and Gate PCB 1. Disassembly of Source PCB CAUTION : Pressure or stress should not be given on PCB and TCP during removing double tape. 2. Disassembly of Gate PCB CAUTION : Pressure or stress should not be given on PCB and TCP during removing double tape.
4 Replacement Procedure 4.29 Fluorescent Lamp Disassembly of Board Ass’y, Tape Adhesi ve, Light guide,Cover Ass’y bottom (L) 1. Disassembly of Board Ass’y CAUTION : This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y.
4.29 Fluorescent Lamp 4 Replacement Procedure Assembly of Cover bottom, Sheets, Light guide, Tape Adhesive, Double Tape and Board Ass’y. To assemble the 15.4-inch WXGA LG.Philips fluorescent lam p, follow the steps below and refer to figures 4-66 to 4-69.
4 Replacement Procedure 4.29 Fluorescent Lamp Assembly of Source PCB 1. Assembly of Source PCB CAUTION : Stress should not be given on TCP during assembling S/M hook.
4.29 Fluorescent Lamp 4 Replacement Procedure Assembly of Cover Ass’y, Screw, Top Case 1. Assembly of Top Case CAUTION : Pressure should not be given on Gate COF.
4 Replacement Procedure 4.29 Fluorescent Lamp Assembly of outside Tape and Cover shield 1. Assembly of Tape shield and Tape Adhesive used for Top case fixing NOTE : Pressure or stress should not be given on Top case during this process. 2. Assembly of Cover shield (S) NOTE : Pressure or stress should not be given on control PCB.
4.29 Fluorescent Lamp 4 Replacement Procedure 4.29.3 Replacing the 15.4-inch WXGA Samsung Fluorescent Lamp Disassembling the 15.4-inch WXGA Samsung Fluorescent Lamp To disassemble the 15.4-inch WXGA Sam sung fluorescent lamp, follow the steps below and refer to figures4-70 to 4-74.
4 Replacement Procedure 4.29 Fluorescent Lamp 3. Remove the two screws from the PCB. Scr ew Scr ew PCB Figure 4-71 Replacing Samsung fluorescent lamp (WXGA) (2) 4.
4.29 Fluorescent Lamp 4 Replacement Procedure 5. Remove the four bottom hooks and four side hooks (left and right) in the order. Then remove the top chassis from the m old frame. ( 2) Side hook (1 ) B o tto m h o o k Figure 4-73 Replacing Samsung fluorescent lamp (WXGA) (4) 6.
4 Replacement Procedure 4.29 Fluorescent Lamp 4-100 Satellite M30-35 Main tenance Manual (960-455) 7. The assembly procedure of the 15.4-inch WXGA Samsung fluorescent lamp is the reverse of the above disassembly procedure.
Appendices.
Appendices App-ii.
Appendices Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout ....................................................................................
Appendices C.23 PJ8490 RTC Battery Connector (3-pin) ..............................................................C-17 C.24 PJ8770 FAN connector (3-pin) ...........................................................................C-17 C.25 PJ2000 Debugging port (4-pin) .
Appendices Figures Figure B-1 System board (FMSSY* 32M) layout (front) ........................................................1 Figure B-2 System board (FMSSY* 32M) layout (back).........................................................3 Figure B-3 System board (FMSMP* 64M) layout (front) .
Appendices Tables Table B-1 System board (FMSSY* 32M) ICs and connectors (front) .....................................2 Table B-2 System board (FMSSY* 32M) ICs and connectors (back) .....................................4 Table B-3 System board (FMSMP* 64M) ICs and connectors (front) .
Appendices Table C-24 FAN connector (3-pin) ....................................................................................C-17 Table C-25 Debugging port (4-pin) ....................................................................................
Appendices App-viii.
Appendix A Handling the LCD Module Appendices Appendix A P Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1.
Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent.
Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge.
Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
Appendix A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassembly can cause m alfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime).
Appendices Appendix A Handling the LCD Module A-6 Satellite M30-35 Main tenance Manual (960-455).
Appendix B Board Layout Appendices Appendix B Board Layout B.1 System Board (FMSSY* 32M) Front View (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) (K) (L) (M) (N) (O) (P) (Q) (R) (S) (T) (U) (V) (W) Figure B.
Appendices Appendix B Board Layout Table B-1 System board (FMSSY* 32M) ICs and connectors (front) Mark Number Name (A) PJ2100 PC card I/F connector (B) PJ7000 CD key I/F connector (C) PJ6001 Internal .
Appendix B Board Layout Appendices B.2 System Board (FMSSY* 32M) Back View (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) Figure B-2 System board (FMSSY* 32M) layout (back) Satellite M30-35 Maintenan ce Manu.
Appendices Appendix B Board Layout Table B-2 System board (FMSSY* 32M) ICs and connectors (back) Mark Number Name (A) PJ3400 Parallel I/F connector (B) PJ3000 MDC I/F connector (C) PJ1820 CD-ROM I/F c.
Appendix B Board Layout Appendices B.3 System Board (FMSMP* 64M) Front View (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) (K) (L) (M) (N) (O) (P) (Q) (R) (S) (T) (U) (V) (W) (X) Figure B-3 System board (FMS.
Appendices Appendix B Board Layout Table B-3 System board (FMSMP* 64M) ICs and connectors (front) Mark Number Name (A) PJ2100 PC card I/F connector (B) PJ7000 CD key I/F connector (C) PJ6001 Internal .
Appendix B Board Layout Appendices B.4 System Board (FMSMP* 64M) Back View (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) Figure B-4 System board (FMSMP* 64M) layout (back) Satellite M30-35 Maintenan ce Manu.
Appendices Appendix B Board Layout B-8 Satellite M30-35 Main tenance Manual (960-455) Table B-4 System board (FMSMP* 64M) ICs and connectors (back) Mark Number Name (A) PJ3400 Parallel I/F connector (.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-1 C Appendix C Pin Assignment System Board (common to FMSSY* 32M, FMSMP* 64M) C.1 IS1400/1401 Memo ry connector (200-pin) Table C-1 Memory connector (200-pin)(1/4) Pin No.
Appendices Appendix C Pin Assignment C-2 Satellite M30-35 Main tenance Manual (960-455) Table C-1 Memory connector (200-pin)(2/4) Pin No. Signal name I/O Pin No.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-3 Table C-1 Memory connector (200-pin)(3/4) Pin No. Signal name I/O Pin No.
Appendices Appendix C Pin Assignment C-4 Satellite M30-35 Main tenance Manual (960-455) Table C-1 Memory connector (200-pin)(4/4) Pin No. Signal name I/O Pin No. Signal name I/O 195 SMBCLK-P3P I/O 196 GND - 197 P3V - 198 GND - 199 N.C - 200 N.C - C.2 PJ1800 HDD I/F connect or (44-pin) Table C-2 HDD I/F connector (44-pin) Pin No.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-5 C.3 PJ1820 CD-ROM I/F connector (50-pin) Table C-3 CD-ROM I/F connector (50-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 CDAUDL-EXP I 2 CDAUDR-EXP I 3 CD-GND I 4 N.
Appendices Appendix C Pin Assignment C-6 Satellite M30-35 Main tenance Manual (960-455) C.4 PJ2100 PC card I/F connector (68-pin) Table C-4 PC card I/F connector (68-pin) (1/2) Pin No.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-7 Table C- PC card I/F connector (68-pin) (2/2) Pin No. Signal name I/O Pin No. Signal name I/O 59 ACSERR-BYN I/O 60 ACREQ-BYN I/O 61 ACCBE3-BYN I/O 62 ACAUDI-BYP I 63 ACSTSC-BYP I 64 ACAD28-BYP I/O 65 ACAD30-BYP I/O 66 ACAD31-BYP I/O 67 ACCD2-B3N I 68 GND - C.
Appendices Appendix C Pin Assignment C-8 Satellite M30-35 Main tenance Manual (960-455) C.6 PJ2200 Mini PCI I/F connector (124-pin) Table C-6 Mini PCI I/F connector (124-pin) (1/2) Pin No. Signal name I/O Pin No. Signal name I/O 1 N.C. - 2 N.C. - 3 N.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-9 Table C-6 Mini PCI I/F connector (124-pin) (2/2) Pin No. Signal name I/O Pin No.
Appendices Appendix C Pin Assignment C-10 Satellite M30-35 Maintenance Manu al (960-455) C.7 PJ3000 MDC I/F connector (30-pin) Table C-7 MDC I/F connector (30-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 N.C - 2 GND - 3 GND - 4 N.C - 5 N.C - 6 N.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-11 C.8 PJ3200 Keyboard I/F connector (34-pin) Table C-8 Keyboard I/F connector (34-pin) Pin No.
Appendices Appendix C Pin Assignment C-12 Satellite M30-35 Maintenance Manu al (960-455) C.10 PJ3400 Parallel I/F Connector (25-pin) Table C-10 Parallel I/F connector (25-pin) Pin No.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-13 C.12 PJ4200 1394 I/F connector (4-pin) Table C-12 1394 I/F connector (4-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 TPB0-P3N I/O 2 TPB0-P3P I/O 3 TPA0-P3N I/O 4 TPA0-P3P I/O C.
Appendices Appendix C Pin Assignment C-14 Satellite M30-35 Maintenance Manu al (960-455) C.14 PJ5621 CRT I/F connector (20-pin) Table C-14 CRT I/F connector (20-pin) Pin No. Signal name I/O P i n N o . Signal name I/O 1 GND - 2 TVLOUT-PXP O 3 GND - 4 TVCOUT-PXP O 5 GND - 6 N.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-15 C.17 PJ6003 Speaker Connector (right) (3-pin) Table C-17 Speaker connector (right) pin assignment (3-pin) Pin No. Signal name I/O P i n N o . Signal name I/O 1 SPKOTR-EXN O 2 N.
Appendices Appendix C Pin Assignment C-16 Satellite M30-35 Maintenance Manu al (960-455) C.19 PJ7001 Power switch I/F connector (15-pin) Table C-19 Power switch I/F connector (15-pin) Pin No.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-17 C.21 PJ7004 Panel switch I/F connector (2-pin) Table C-21 USB connector PCB I/F connector (2-pin) Pin No. Signal name I/O P i n N o . Signal name I/O 1 PNLOFF-S3V I 2 GND - C.
Appendices Appendix C Pin Assignment C-18 Satellite M30-35 Maintenance Manu al (960-455) C.25 PJ2000 Debugging port (4-pin) Table C-25 Debugging port (4-pin) Pin No.
Appendix C Pin Assignment Appendices Satellite M30-35 Main tenance Manual (960-455) C-19 (only for FMSSY* 32M) C.26 PJ7003 USB connector PCB I/F connector (4-pin) Table C-26 USB connector PCB I/F connector (4-pin) Pin No. Signal name I/O P i n N o . Signal name I/O 1 USB1PS-E5V O 2 USBP2C-S3N O 3 USBP2C-S3P O 4 GND - (only for FMSMP* 64M) C.
Appendices Appendix C Pin Assignment C-20 Satellite M30-35 Maintenance Manu al (960-455).
Appendix D Keyboard Scan/Character Codes Appendices Satellite M30-35 Maintenance Manual (960-455) D-1 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes D-2 Satellite M30-35 Maintenance Manual (960-455) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes Satellite M30-35 Maintenance Manual (960-455) D-3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes D-4 Satellite M30-35 Maintenance Manual (960-455) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes Satellite M30-35 Maintenance Manual (960-455) D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes D-6 Satellite M30-35 Maintenance Manual (960-455) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes Satellite M30-35 Maintenance Manual (960-455) D-7 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No.
Appendices Appendix D Keyboard Scan/Character Codes D-8 Satellite M30-35 Maintenance Manual (960-455) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm o n * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.
Appendix E Key Layout Appendices Appendix E Appendix E Key Layout E.1 United Kingdom (UK) Keyboard Figure E-1 UK keyboard E.2 United States (US) Keyboard Figure E-2 US keyboard Satellite M30-35 Mainte.
Appendices Appendix E Key Layout E-2 Satellite M30-35 Maintenance Manual (960-455).
Appendix F Wiring Diagrams Appendices Appendix F Appendix F Wiring Diagrams F.1 Parallel Port Wraparound Connector -SELECT -PINT Figure F-1 Parallel port wraparound connector F.
Appendices Appendix F Wiring Diagrams F-2 Satellite M30-35 Maintenance Manual (960-455).
Appendix G BIOS Rewrite Procedures Appendices Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KBC rewriting disk for the com puter that has renewed BIOS data.
Appendices Appendix G BIOS Rewrite Procedures G-2 Satellite M30-35 Maintenance Manual (960-455).
Appendix I Reliability Appendices Appendix I Appendix I Reliability The following table shows MTBF (Mean Time between Failures). Table I-1 MTBF MTBF Time (hours) VRAM32MB (FMSSY* board) model 7323.
Appendices Appendix I Reliability I-2 Satellite M30-35 Maintenance Manual (960-455).
Appendix J SETUP Appendices Appendix J Appendix J SETUP This function displays the current system setup information. The options are listed blow. 1. Main (1) Total Memory (2) System Date (3) System Time (4) BIOS Ver.
Appendices Appendix J SETUP To access the SETUP display, power on the computer and while “TOSHIBA” logo is displayed, press [F2] . Then, the main menu sim ilar to the one blow appears. There are five tabs (Main, Advanced, Security, Boot and Exit) in the SETUP menu.
Appendix J SETUP Appendices Advanced 1. Power On Display [Auto-Selected] If any external display is connected, the power on display will be in analog RGB only mode. Otherwise it will be in LCD only mode. [LCD+Analog RGB] Display both the integrated LCD screen and analog RGB screen mode.
Appendices Appendix J SETUP J-4 Satellite M30-35 Maintenance Manual (960-455) 9. Parallel Port Mode This option sets the mode for the parallel port using options. [ECP] Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to “ECP.
デバイスToshiba M30-35の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba M30-35をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba M30-35の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba M30-35の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba M30-35で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba M30-35を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba M30-35の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba M30-35に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba M30-35デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
