ToshibaメーカーP40の使用説明書/サービス説明書
ページ先へ移動 of 192
GMAD00380010 09/13 If you need assistance: T echnical support is available online at T oshiba’ s W eb site at support.tosh iba.com . At this W eb site, you will find answers for many commonly asked tec hnical questions plus many downloadable software drivers, BIOS upda tes, and othe r downloads.
2 5.375 x 8.375 ver 2.3 Handling the cord on this prod uct will expose you to lead, a chemical known to the State of Ca lifornia to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Protection of Stored Data For your important data, please make periodic back-up cop ies of all the data stored on th e hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data.
4 5.375 x 8.375 ver 2.3 FCC Notice “Declarati on of Conformity Information” This equipment has be en tested an d found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits ar e designed to pr ovide reasonable pr otection against harmful interference in a residential installation.
5 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnology Interoperability Bluetooth ® modules ar e designed to be interoperable with any product with Bluetooth wireless technolo gy that is based on .
6 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnology and Y our Health The products with Bluetooth ® wireless technology , like other radio devices, emit radio frequency electr omagnetic ener gy .
7 5.375 x 8.375 ver 2.3 Wireless Interoperability Wireless LAN pr oducts ar e designed to be interoperable with any wireless LAN pr oduct that is ba sed on Direct Sequence Spr ead Spectrum (DSS S) radio techno logy , and is compliant to: ❖ The IEEE 802.
8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health Wireless LAN products, like other ra dio devices, emit radio frequency electromagnetic ener gy . The level of ener gy emitted by Wirele ss LAN devices however is far much less than the electr omagnetic ener gy emitted by wireless devices lik e for example mobile phones.
9 5.375 x 8.375 ver 2.3 Optical Disc Drive Safety Instructions This section is only applicabl e if your sys tem has an Optical Disc Drive. This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT . T o use this model pr operly , read th e User’ s Guide carefully an d keep it for your future refe ren ce .
10 5.375 x 8.375 ver 2.3 Operation is subject to the followi ng two conditions: (1) this device may not cause interference , and (2) this device must accept any interferenc e, including interference that may cause undesir ed operation of this device.
11 5.375 x 8.375 ver 2.3 Regulatory statements This product complies with any man datory product specification in any country/region whe re the pr oduct is so ld.
12 5.375 x 8.375 ver 2.3 In the European Union, these symbols indicate that when the last end user wishes to discar d this product, it must be sent to appropr iate facilities for recovery and r ecyclin g. This Directive applies to EU member countries only and does not apply to end users in other countries such as the United States.
13 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance w ith European spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply .
14 5.375 x 8.375 ver 2.3 listed above, the user must cease operating the Wireless LAN at that location and consult the local te chnical support staff responsib le for the wireless network. ❖ The 5 GHz T urbo mode feature is not allowed for operation in any European Comm unity country .
15 5.375 x 8.375 ver 2.3 Using this Equi pment in Japan In Japan, the frequency bandwidt h of 2,400 MHz to 2,483.5 MHz for second g eneratio n low-power d ata communication sy stems such as this equipment overlaps that of mo bile object iden tification systems (premises radio station and speci fied low-power radio station).
16 5.375 x 8.375 ver 2.3 3 The interference range of this equipment is less than 10m. 4 This equipment uses a fr equency bandwi dth from 2 ,400 MHz to 2,483.
17 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical da ta that may be contr olled under the U.S. Export Administration Re gulations, and may b e subject to the approval of the U.S. Department of Commerce prior to export.
18 5.375 x 8.375 ver 2.3 T rademarks Satellite, Satellite Pro, and ec o Util ity are either register ed trademarks or trademarks of T oshiba America Information System s, Inc. and/or T oshiba Corporation. Adobe and Photoshop are either register ed trademarks or trademarks of Adobe Sy stems Incorporat ed in the United States and/or other countries.
19 5.375 x 8.375 ver 2.3 Computer Recycling Information As part of a commitment to people and the future, T oshiba promotes the efficient use of r esources by working to achieve our zer o-waste- to-landfill goal at all o ur production si tes.
20 5.375 x 8.375 v er 2.3 Contents Chapter 1: Introducti on ..................... ...................... 26 This guide ...................................... ...................... 28 Safety icons ............................................. ........
21 Contents 5.375 x 8.375 v er 2.3 Check list ...................................................... . 36 Precautions ................................................... . 37 Important information on your computer’s cooling fan......................
22 Contents 5.375 x 8.375 v er 2.3 Caring for your computer ..................................... 75 Cleaning the computer .................................. 75 Moving the computer ..................................... 75 Using a computer lock .......
23 Contents 5.375 x 8.375 v er 2.3 What to do when the main battery runs low ................................................ ............ 96 Setting battery notifications ........................... 96 Conserving battery power .......................
24 Contents 5.375 x 8.375 v er 2.3 Deleting a user password ............................ 124 System Settings ................................................. 125 Sleep Utilities ..................................................... 127 USB Sleep and Charge .
25 Contents 5.375 x 8.375 v er 2.3 If you need further assistance ............................ 162 Contacting Toshiba ...................................... 163 Other Toshiba Internet Web sites ...................... 163 Toshiba’s worldwide offices .
26 Introduction W elcome to the world of powerfu l, portable, multimedia computing. With y our T oshiba comput er , yo ur work and entertainmen t can accompan y you wherever you go.
27 Introduction 5.375 x 8.375 ver 2.3 When considering addition s to your ho me office, purchase products that have ear ned the ENERG Y ST AR ® for all your equipment nee ds, which ca n save you mon ey , save energy , and help pr otect the c limate. Visit http://www .
28 Introduction This guide 5.375 x 8.375 ver 2.3 The pr oduct specifications an d configuration information are designed for a product Ser ies. Y our particular model may not have all the feat ures and specifications listed or illustrated.
29 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual c ontains safety instructions th at must be observed to avoid po tential hazards that could result in personal injuries, damag e to your equipm ent, or loss of da ta.
30 Introduction Documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are designed to accommo date all possible configuratio ns for an entire product Series.
31 Chapter 1 Getting Started This chapter provides tips for using your comput er effectively , summarizes how to connect componen ts, and explains what to do the first time you use your co mputer .
32 Getting Started Selecting a place to work ❖ Equipment t hat generate s a strong electromagnetic field, such as stereo speak ers (other tha n speakers th at are connected to the computer) or speakerphon es. ❖ Rapid changes in temper ature or humidity and sources of temperature change such as air conditioner vent s or heaters.
33 Getting Started Selecting a place to work ❖ When typing, k eep your wrists straigh t and try not to rest your wr ists on the not ebook. Support your arms on your forearm area. The forearms can be supported by the chair arm supports o r the desk surface .
34 Getting Started Selecting a place to work ❖ When using a n otebook for long hours, it may be more comfortable to do ck the noteboo k and use an ex tern al keyboard, mouse and monitor . ❖ The keyboa rd and mouse (or tra ckball) shou ld be close to your el bow level.
35 Getting Started Selecting a place to work T aking breaks and varying tasks ❖ Change the wa y you work s o that you are not stu ck in the same postu re for long periods of time. Some people find it comfortable to occasi onally stand while using the notebook.
36 Getting Started Selecting a place to work Seeking additional help Follow the advice fr om your employ er’ s company heal th and safety staff. Contact them if you need assistance mak ing adjustment to your workstat ion or adjus ting the lighting.
37 Getting Started Selecting a place to work Precautions Y our compute r is designed to provide optimum safety a nd ease of use, and to withstand th e rigors of travel. Y o u should observe cer tain precautions t o further reduce the risk of personal injury or damage to the co mputer .
38 Getting Started Selecting a place to work Consider us ing a hard computer insulating pad or similarly suitable hard insula ting material when using a computer on your lap. Never place a h eavy object on t he computer and be careful not to drop a heavy object onto the compute r .
39 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer .
40 Getting Started Connecting to a power source Please handle yo ur computer carefully to a void scratching or damaging the surface. Connecting to a power source Y our computer r equir es power to operate. Use the powe r cord/cable and AC adaptor t o connect the c omputer to a live electrical outlet, or to charge the computer’ s battery .
41 Getting Started Connecting to a power source (Sample Illustration) Power cord/cable and AC adapto r T o connect AC po wer to the co mputer: 1 Connect th e power cord/cable to the AC adapto r .
42 Getting Started Charging the main battery 3 Connect the po wer cord/cable to a live electrical outlet. The AC power lig ht on the indicator panel glows white. Never attempt to conn ect or disconnect a powe r plug with wet hands. Failur e to follow this instruction could result in an electric shock, possibly resulting in serious injury .
43 Getting Started Using the computer for the first time Using the computer for the first time The computer is now ready for you to t urn it o n and begin using it, see “Exploring Y our Computer’ s Featur es” on page 107 .
44 Getting Started Registering your computer with T oshiba Setting up your software When you turn on the computer f or the first time, do not turn off the power again unt il the operating syst em has loaded completely . The names of windows displayed, an d the order in which windows appear , may vary accor ding to your software setup choices.
45 Getting Started T o Shut down your computer T o Shut down your computer 1 From the Start or Deskto p screen, move your pointer t o the upper -ri ght corner of the scr een or swipe in fr om the right edge. 2 When the Windows ® charms appear , click or touc h the Settings ( ) charm.
46 Getting Started T o Restart your computer T o Restart your computer 1 From the Start or Deskto p screen, move your pointer t o the upper -ri ght corner of the scr een or swipe in fr om the right edge. 2 When the Windows ® charms appear , click or touc h the Settings ( ) charm.
47 Getting Started Adding optional external devices 3 In the lower r ight of the scr een click or t ouch the Power () i c o n . (Sample Imag e) Sleep 4 Highlight Sleep , and then click or touch the Sleep option.
48 Getting Started Adding memory (optional) Adding memory (optional) HINT : T o purchase additional me mory modules, see the accessor ies inf ormation packag ed with your syst em or visit accessories.toshiba.com . Y ou r c o m p u t e r comes with enough memory to run most of today’ s popular applications.
49 Getting Started Adding memory (optional) Before you install or r emove a memory module, turn off the computer . If you install or remove a memory module while the computer is in Slee p or Hibe rnat ion mode, data will be lost. For this model, Slo t A is the bottom slot.
50 Getting Started Adding memory (optional) 5 Unplug and remove any cable s connected to the computer , including the AC a daptor . Do not try to r emove a memory module with the computer turned on. Y ou can damage the computer and the memory module. Do not remove the memory module while the comput er is in Sleep or Hiber nation mode.
51 Getting Started Adding memory (optional) 12 Locate an empt y memory module slot o n the undersi de of the computer . If no memory slot is available, you must remove a module by performing steps 2 - 3 of “Removing a memory module” on page 54 .
52 Getting Started Adding memory (optional) 14 Firmly pre ss the memory modu le into the memory slot’ s socket at a pproximately a 30-degree angle (t o the horizontal surf ace of the c omputer).
53 Getting Started Adding memory (optional) (Sample Illustration) Inserting th e memory module into the slot For this model, Slo t A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A.
54 Getting Started Removing a memory module 19 Reconnect th e cables. 20 Restart the co mputer . TECHNICAL NOTE: Y ou must ha ve at least on e memory module installed for the co mputer to work.
55 Getting Started Removing a memory module 3 Gently lift the me m or y module to a 30-degree angle an d slide it out o f the slot. (Sample Illustration) Remo ving th e memory modu le 4 Replace the memory modu le slot cover and se cure it using the screw(s).
56 Getting Started Recovering the Inter nal Storage Drive 7 Reconnect th e cables. 8 Restart the co mputer . TECHNICAL NOTE: Y ou must ha ve at least on e memory module installed for the co mputer to work. Checking total memory When you add or r emove a memo ry mo du le , you can check that the compu ter has recognized the ch ange.
57 Getting Started Recover ing the Internal Storage Dr ive A recovery image of you r computer is st ored on the inter nal storage dr ive, and th e image can be r estor ed by running t he recovery utilities dir ectly from your internal storage drive as described in the section s belo w .
58 Getting Started Recovering the Inter nal Storage Drive Creating recov ery media It is strongly recommended that you create r ecovery media. If the recovery files on your inter nal storage drive become corrupted or are deleted, y ou can restore your system from your recovery media.
59 Getting Started Recover ing the Internal Storage Dr ive The TOSHIBA Recovery Media C reator dialog box displays. (Sample Image) TOSHIBA Recovery Media Cr eator dialog box 2 Select DVD or USB Flash from the drop-down lis t, depending on the type of external media you want to use.
60 Getting Started Recovering the Inter nal Storage Drive If you are copying the recovery files to DVDs, be sure to label each DVD in the set se quentially (for exa mple, “1 of 3,” “2 of 3,” etc.), so that you will know in which order to insert the discs during r ecovery .
61 Getting Started Recover ing the Internal Storage Dr ive ❖ If your recovery files are on a USB flash drive, connect the U SB flash drive to your compu ter . 3 T u rn on yo ur computer while pressing the F12 key on your keyboard. The Boot menu displays.
62 Getting Started Recovering the Inter nal Storage Drive Y ou can recover t he factory defa ult software (r efresh your PC), while the comput er will attempt to ba ck up your data using the utilities stored on your computer’ s internal storage drive: TECHNICAL NOTE: Y our data will be copied into the backup folder .
63 Getting Started Recover ing the Internal Storage Dr ive 6 Select Refresh your PC without affecting your files , and click or tou ch Get Started . The “Refr esh you r PC” scr een appears . (Sample Image) Refresh your PC screen T oshiba does not guar antee successful dat a back up.
64 Getting Started Recovering the Inter nal Storage Drive 9 Y our system will restart. The “Refr eshing your PC” wind ow appears. When the process is complete your system will reboot your Windows ® operating sy stem. Reset your PC The recovery process delete s information stored on the internal storage dr ive.
65 Getting Started Recover ing the Internal Storage Dr ive 6 Select Remove everything and reinstall Windows , and click or tou ch Get Started . The “Reset your PC” sc reen appe ars. (Sample Image) Reset y our PC screen 7 Click or touch the Next button.
66 Getting Started Recovering the Inter nal Storage Drive The “Ready to reset your PC” screen appears. (Sample Image) Ready to reset your PC screen 9 Click or touch the Reset button. The “Resetting your PC” wi ndow appears. Whe n the process is complete your system will reboot your Windows ® operating sy stem.
67 Getting Started Using the touch pad (Sample Image) Installing drivers and applications 2 Click or touch Next . 3 Click or touch the item you want to install. 4 Click or touch Install . 5 Follow the on-scr een prompts to comp lete the installation process, see “TOSHIBA Application Installer” on page 1 34 .
68 Getting Started Using the touch pad ❖ Zoom in for a clo se-up view ❖ Zoom out to see mor e information at once (Sample Illustration) The touch pad and associated contr ol buttons Refer to the ta ble below for specific instructions on performing each operation.
69 Getting Started Using the touch pad Open or activate an it em 1 Move the pointe r to the item you want to open/activate. 2 Do one of the following : ❖ T ap the touch pad twice in rapid succession.
70 Getting Started Using the touch pad Adjusting touch pad settings While you ar e typing, th e on-scr een pointer may s eem to move or jump around “by itself” to ran dom locations on the scr een. The on-scr een pointer may also seem to automatically s elect text, click buttons, and activa te other user interface elements.
71 Getting Started Using the touch pad T ouch pa d setting op tions vary by co mputer model. The touch pad s ettings are accessib le through the Mouse Prope rties option of the Windows Contr ol Panel. For more information, please visit support.toshiba.
72 Getting Started Using external display devices Using external display devices Y our computer co mes with a built-in display , but you can also connect the following types of external display devices to the video ports descr ibed below: T o locate your HDMI™ or RGB port, plea se refer to your Quick Start documen t.
73 Getting Started Using external display devices Connecting an external monitor or projector Y ou can easily attach an e xternal monitor or proje ctor to yo ur computer if yo u need a larger screen. To d o t h i s : 1 Read the directions that came with the monitor to see if you first need to install new software.
74 Getting Started Customizing your computer’ s settings ❖ Second screen only (Sample Image) Display options window The ( ) + P keys navigate through th e options without activating a selection . Press ENTER to activate a selection. Y ou may also u se the F4 key , and then press ENTER to activate a se lection.
75 Getting Started Caring for your computer Refer to your operating system documentation o r Help and Support for de tails. Y ou may als o wish to customize your power u sage settings. For mor e informatio n, see “Power Plans” on page 98 . There are additional custom se ttings you can choose.
76 Getting Started Caring for your computer Using a computer lock Y ou may want to secure your computer to a heavy obje ct such as your desk. The easies t wa y t o d o t hi s i s t o p urc ha se an optional co mputer lock cable. Fo r more information on purchasing a cable lock , visit acces sories.
77 Chapter 2 Learning t he Basics This chapter giv es some computing tips an d provides important information about basic fe atures. Computing tips ❖ Save your work fr equently . Y our work stays in the computer’ s tempor ary memory until you save it to th e intern al storage drive.
78 Learning the Basics Computing tips ❖ Back up your files t o external media on a re gular basis. Label the ba ckup copies clea rly and store them in a safe place.
79 Learning the Basics Using the keyboard Using the keyboard Y our computer may be equipped with a 10-key keyboard, depending on your model. Y our computer’ s ke yboard contains charact er keys, control keys, function keys, and special Win dows ® keys.
80 Learning the Basics Backlit keyboard Function keys The function ke ys (not to be confused with the Fn k ey) are the 12 keys at the top of the keyboard. (Sample Illustration) Function keys F1 through F12 are called function keys be cause they execute programmed functions wh en pressed.
81 Learning the Basics To u c h s c r e e n T ouch screen Y our computer may come with a t ouch screen, enabling dire ct interaction with displayed apps and pr ograms thro ugh simple or multi-touch gestures. T ouch screen navigation Use your fing er to manipulate the on-screen icons, bu ttons, menu items, and other it ems on the touch scr een.
82 Learning the Basics Mouse pr operties Mouse properties Mouse pr operties allo w you to change your pointing devi ce or mouse settin gs. T o access Mou se properties: 1 Move your pointe r to the upper -right corner of t he screen or swipe in f rom the right edge.
83 Learning the Basics Saving your work Below is an exa mple using the Search field to start an app: 1 Move your pointe r to the upper -right corner of t he screen or swipe in f rom the right edge. Whe n the Windo ws ® charms appear click or touch the Search ( ) charm.
84 Learning the Basics Using the optical disc drive HINT : Backing up all the files on your inter nal stor age drive may take a considerable amount of time and multiple CDs/DVDs. Y ou may prefer to use a high- capacity file recovery syst em, such as an external hard drive.
85 Learning the Basics Using the opti cal disc dr ive Optical disc drive components The optical disc drive is located on the side of the computer . Y our optical disc drive may look like this: (Sample Illustration) Optical disc drive Drive in-use indicator light —In dicates when the drive is in use.
86 Learning the Basics Using the optical disc drive Media control buttons The media c ontrol buttons located a bove the key board allow you mute the sound and play audio CDs or DVD movi es when the comput er is on.
87 Learning the Basics Using the opti cal disc dr ive Handle DVDs and CDs carefully , making contact only with the cente r hole and edge. Do not to uch the surf ace of the disc. Do not sta ck discs. If you incorr ectly handle the discs, yo u could los e data.
88 Learning the Basics Using the optical disc drive Due to manufact uring and qualit y variations in thir d party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, .
89 Learning the Basics T oshiba’ s online r esources Never use a pencil to press the ma nual eject bu tton. Pencil lead can break off inside the computer a nd damage it. 2 Pull the tray out until it is fu lly open, remove the disc, and place it in its protective cover .
90 Chapter 3 Mobile Computing This chapter covers all aspe cts of using your computer while traveling. T oshiba’ s energy-saver design Y our computer en ters a low-power suspen sion mode when it is not being use d, thereby conserving en er gy and saving money in the process.
91 Mobile Computing Running the computer on battery power Battery Notice Battery life r ating is for compar ison purpos es only , and does not indicate th e battery life tha t will be obtained by any individual user .
92 Mobile Computing Charging batteries The RTC battery powe rs the RTC memory that stores your system configur ation settings and the current time and dat e information. It main tains this informatio n for up to a month while the computer is tu rned off.
93 Mobile Computing Charging batter ies TECHNICAL NOTE : The rechar ging of the battery may not occur wh en your compu ter is using all of the power provided by the AC adaptor to r un applications, fe atures, and devices.
94 Mobile Computing Monitoring battery power Depending on your system, the RTC battery may only charge while the computer is tu rned on . T o rechar ge the RTC battery , plug the computer int o a live electrical outlet and leave the computer powered on for 24 hours.
95 Mobile Computing Monitoring battery power HINT : Be careful not to confuse the battery light ( ), the power light ( ), and the power button light. When the power light o r power button light flashes amber , it indicates that the system is suspended (using the Windows ® operating system Sleep command).
96 Mobile Computing Monitoring battery power TECHNICAL NOTE: T he computer drains t he battery faster at low temperatur es. Check your r emaining char ge frequently if you are working in te mperatures below 50 degr ees Fahr enheit.
97 Mobile Computing Monitoring battery power 4 Click or touch Change advanced power settings . The Advance d settings tab o f the Powe r Options window appears. 5 Double-click or touch Battery to display the battery options. (Sample Image) Advanced settings tab of Power Options screen 6 Configur e the alarm settings to suit your needs.
98 Mobile Computing Monitoring battery power These power -saving options con trol the way in which the computer is co nfigured. By using them , you can increase the length of time you can use the computer befo re you need to rechar ge the battery . Microsoft ® has combined these options into preset Power Plans.
99 Mobile Computing Using the eco power plan T o edit a plan or to edit advanc ed settings, con tinue to the following steps. 5 Click or touch Change plan settings to choose the plan you want to edit. This scre en allows you to cha nge basic settings.
100 Mobile Computing Changing the main battery Changing the main battery This User's Guide covers an entire pr oduct series. Certain models may not have an accessible batt ery . For models with a non-accessible battery r ead the following Changing the main battery information.
101 Mobile Computing Changing the main battery Removing the battery from the computer T o remove the battery: 1 Save your work . 2 T u rn off the computer , see “T o Shut down your computer” on pa ge 45 . 3 Unplug and remove any cable s connected to the computer , including the AC adapto r .
102 Mobile Computing Changing the main battery If the battery is leaking or its case is cracked, put on prot ective gloves to ha ndle it, and disc ard it immediately . Always dispose of used batt ery packs in compliance with all applicable laws and regula tions.
103 Mobile Computing T aking car e of your battery 3 Slide the batter y releas e lock to the locked posit ion. (Sample Illustration) Locking the ba ttery release lock 4 T u rn the co mputer right side up. 5 Reconnect an y cables that wer e r emoved in step 3 of “Removing the bat tery fr om the computer” on page 1 01 .
104 Mobile Computing Disposing of your computer Maintaining your battery Fully dischar ging your battery pack will allow better accuracy of the battery mete r . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it o n battery power u ntil the battery pack fully dischar ges.
105 Mobile Computing Disposing of your computer Disposing of used batt eries For models with an accessible battery read the following disposal information. The life of a battery pack depen ds on usage. Wh en the battery pack n eeds replacing, the main ba ttery light flash es amber short ly after you have fully recharged the batter y .
106 Mobile Computing T raveling tips T oshiba is dedicated to preserving the environment by sponsoring Call2Recycle ™ , a program of t he Rechar geable Batt ery Recycling Corpor ation, so you can eas ily rec ycl e acc ess ible recha rgeable batt eries .
107 Chapter 4 Exploring Y our Computer’ s Features In this chapter , you will explor e some of the special features of your comp uter . Exploring the Start screen The Start scr een is the launch ing.
108 Exploring Y our Computer’s Features Exploring the Start screen For detailed information on th e new functionalit y , r efer to the Windows ® Help and Support. (Sample Image) Windows ® Start screen Charms Use the Windows ® charms to start apps, find documents, set up system component s, and perform most ot her computing tasks.
109 Exploring Y our Computer’ s Features Exploring the desktop T iles Tiles can be acce ssed and launched f rom the Start screen. T ypical Start screen tiles are th e Desktop tile and Mail tile, as well as tiles repr esenting all other applicatio ns downloaded to your system.
110 Exploring Y our Computer’s Features Exploring the desktop Icons An icon represents a folder , file, or program that can be quickly activated by double-c licking or touching the icon. Y ou can create a n ew desktop icon f or any folder , file, or prog ram by dragging the element’ s icon fr om its location in a window to the desktop ar ea.
111 Exploring Y our Computer’ s Features Windows ® Store Notification area The notifica tion area displays icons of tasks or programs that run continuously in the background and disp lays notifications . T o lear n more about each task , position the pointer ove r the icon for a few moment s and a short descr iption of the task ap pears.
112 Exploring Y our Computer’s Features Setting up for commun ications Setting up for communications T o connect to the Inte rnet yo u need: ❖ A browser or communications program ❖ An Internet S.
113 Exploring Y our Computer’ s Features Exploring audio features Connecting your computer to a network Y ou can connect your computer to a n etwork to inc rease its capabilities and functionality . Accessing a network For specific inf ormation abou t connectin g to the netw ork, consult your netw ork administrator .
114 Exploring Y our Computer’s Features Exploring audio featur es 5 When you have finished recording, click or touc h the Stop Recording button. The Save As dialog box appears.
115 Exploring Y our Computer’ s Features Using the W eb Camera Using the Web Camera Y our computer may come with a built-in W eb Camera. With this W eb Camera y ou can do the following: ❖ T ake pi.
116 Exploring Y our Computer’s Features Using the Memory card reader Inserting memo ry media T o locate yo ur Memory card reader , plea se refer to your Quick Start documen t. The following instruct ions apply to all types of supported media devices.
117 Exploring Y our Computer’ s Features Using the Memory card r eader 3 Highlight, and then click or touch the item you would like to eject. If the syste m is unable to pr epar e the media for safe removal, a message will tell you to try again later .
118 Chapter 5 Utilities Y our computer includes several utilities designed to help you to reconfigur e your system to best meet yo ur individual needs. T ogether , these allow you to ascertain ce rtain system details, set additio nal options, or chan ge default options.
119 Utilities eco Utility ® eco Utility ® The eco Utility ® monitors your power savings from usin g the eco power plan by trackin g real-time power consumption and accumulated savin gs over time. T o access the eco Utility ® : 1 From the Start screen begin typing eco Utility .
120 Utilities Password Utility Password Utility Setting a passw ord lets you walk away from your com puter while providing additional protection for yo ur files. When you set a passwor d, you must enter the pas sword be fore you can work on your comput er again.
121 Utilities Password Utility 2 Click or touch Password Utility . (Sample Image) Supervisor Passw ord tab 3 Click or touch Supervisor Password . 4 Click or touch Set . 5 Enter your passwo rd, and then enter it aga in to verify . 6 Click or touch Set .
122 Utilities Password Utility Deleting a supervisor password T o delete a supervis or password: 1 T o access Supervisor Passwor d from th e Start scr een begin typing Password Utility . 2 Click or touch Password Utility . A pop-up scr een appears asking for a passwor d.
123 Utilities Password Utility 2 Click or touch Password Utility . 3 Click or touch User Password . (Sample Image) User Pas sword tab 4 Click or touch Set . 5 Enter your passwo rd, and then enter it aga in to verify . 6 Click or touch Set . 7 Click or touch OK to save your passwo rd as a text file.
124 Utilities Password Utility Deleting a user password T o cancel th e power -on password function: 1 T o access User Passw ord fr om the Start screen begin typing Password Utility . 2 Click or touch Password Utility . A pop-up scr een appears asking for a passwor d.
125 Utilities System Settings System Settings System Settings is the TOSH IBA configu ration management tool available thr ough th e Windows ® operating system. T o access it: 1 T o access Syst em Settings from the Start s creen begin typing System Settings .
126 Utilities System Settings ❖ Display —Allows you to change various default settings for the built-in display When the compu ter restarts, it remembers the last configuration. If data does not appear on the display you are using after start ing in Sleep mode, press the ( ) + P keys to toggle the display .
127 Utilities Sleep Utilities Sleep Utilities This utility displays whether the “USB Sleep and Charge function” is en abled or disabled and sh ows the position of the USB port th at supports the “USB Sleep and Cha r ge function.” 1 T o access Sleep Utilities from the Start scr een begin typing System Settings .
128 Utilities Sleep Utilities ❖ When “USB Sleep and Char ge function” is set to Enabled, USB bus power (DC 5V) will be supplied to the compatible port even when the power of the computer is turned OFF . USB bus power (DC 5V) is similarly supplied to the exter nal devices which ar e connected to the compatible ports .
129 Utilities Sleep Utilities Enabling/Disabling USB Sleep and Charge This utility can be us ed to enable or di sable the USB Sleep and Char ge functio n. T o enable this fun ction, select Enable . T o disable this function, toggle the E nable button to the Disabled position.
130 Utilities Sleep Utilities With certain exter nal devices, th e USB Sleep and Char ge function may no t work no matter wh ich char ging mode you select. In those cases, disable USB Sleep and Char ge in the utility and turn the computer on to char ge the device, or use a different charging device.
131 Utilities HDD Protection Utility HDD Protection Utility The HDD Protection Utility cont ro ls your computer’ s hard disk drive (HDD) protection feature, which parks the HDD whenever moti on is detected on t he computer .
132 Utilities Function Key Function Key TOSHIBA Function Ke y enables you to activa te functions by pressing specific keys either singly or in combination with Fn . Some function s show the toast n otification at the edge of t he scre en. These settings turn notificati ons ON/OFF .
133 Utilities Recovery Media Creator Recovery Media Creator The Recovery Media Creator ut ility enables you to create recovery media that can be u sed to return your system to its out-of-box stat e, if necessary . Fo r detailed informa tion on using the utility to create recovery media, see “Creating recovery media” on page 58 .
134 Utilities TOSHIBA Application Installer TOSHIBA Application Installer The TOSHIBA Application Installe r allows you to reinstall the drivers and applicatio ns that were or igin ally bundled with your computer . Y ou must have an Internet connection to reinsta ll applications.
135 Chapter 6 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identif y and solve. Ot hers may r equire help from yo ur network administ rator or the manufacturer of the softw are pr ogram. This chapter aims to help you solve many problems by yourself.
136 If Something Goes Wrong Problems when you turn on the computer If you ar e working in a pr ogram tha t suddenly fr eezes, chances are the program has stopped responding. Y ou can exit the pr ogram without shut ting down the ope rating system or closing other pr ograms.
137 If Something Goes Wrong Problems when you turn on the computer The computer displays the WARNING RESUM E FA I L U R E / Windows Error Recovery – Windows did not shut down successfully message. T o continue , select Start Windows normally . This can happen if the c omputer was put into Slee p mode and the battery ha s dischar ged.
138 If Something Goes Wrong The Windows ® operating system is not working 3 If your comput er has a removable batt ery , connect the AC adaptor to t he computer . Leave the battery out of the computer . T ry tu rning the computer on again . If the comput er starts norm ally , the batt ery may need char ging, may be depleted, or ma y be defective.
139 If Something Goes Wrong The Windows ® operating system i s not working Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device. If you experience any of these problems, use t he options in the Startup menu to fix the problem.
140 If Something Goes Wrong The Windows ® operating system is not working Reset your computer ❖ All of your pers onal files and apps are removed ❖ Y our computer set tings are changed back to their defaults For mor e informatio n, see “Reset your PC” on page 64 .
141 If Something Goes Wrong The Windows ® operating system i s not working ❖ Enable debugging mode Starts Windows ® in an advanced troubleshooting mode ❖ Enable boot logging Creates a file that lists a ll the dr ivers that ar e installed during startup ❖ Enable Safe Mode Starts Windows ® with a minimal s et of drivers and services.
142 If Something Goes Wrong Fixing a problem with Device Manager My browser cannot find a site I bookmarked. The W orld Wide W eb is con stantly changing. A site you bookmarked yesterday may not be available today o r its server may be down f or temporar y repair .
143 If Something Goes Wrong Memory problems Checking device properties Device Manager provid es a way to view the pr operties of a device. Properties include the name of the manu facturer , the type of device , the drivers installed, an d the system resources assigned to the device.
144 If Something Goes Wrong Memory problems 2 When the Windows ® charms appear , click or touc h the Settings ( ) charm. 3 In the lower r ight of the scr een click or t ouch the Power () i c o n . (Sample Image) Shut down 4 While holding the Shift key , clic k or touch the Shut down option.
145 If Something Goes Wrong Power and the batteries Power and the batteries The computer bat tery may not be acc essible by the us er . Y our computer re ceives its po wer thr ough the AC adaptor and power cor d/cable or from the syste m batter ies (battery and real-time clock (RTC) battery).
146 If Something Goes Wrong Keyboard pr oblems The battery appears not to power th e computer for as long as it usually does. If you fr equently r epeat shallow char ge and dischar ge, the battery meter may become inaccura te. Let the bat tery discharge completely , then try charging it again.
147 If Something Goes Wrong Display problems Display problems Here are some typical display problems and their solutions: The screen is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. If you are using the built-in screen, make sure the display prior ity is not set for an external monitor .
148 If Something Goes Wrong Display problems A message displays saying that there is a problem with your display settings and that t he adapter type is incorrect or the current settings do not work with your hardware. Reduce the size of the color palette to one that is suppo rted by the computer’ s inter nal display .
149 If Something Goes Wrong Disk or storage drive pr oblems Disk or storage drive problems Proble ms with the storage dr ive or with external media usually show up as an inability to access the drive or as sector errors. Sometimes a drive pr oblem may cause o ne or more files to appear to have garbage in them.
150 If Something Goes Wrong Optical disc drive problems 7 Even if you do not need to s can the drive for errors you can scan by c licking or touching Scan drive . Error -checking test s and repairs the storage drive. Y our hard disk seems very slow . If you have been using you r computer for a long time, you r files may have become fragmented.
151 If Something Goes Wrong Optical disc drive problems Examine the disc to see if it is dirty . If necessary , wipe it with a clean cloth dipped in water or a ne utral cleaner . Replace the dis c in the tray . Make su re that the disc is lying flat against the tray , label side up.
152 If Something Goes Wrong Sound system pr oblems Sound system problems No sound is coming from the computer’ s speakers. Adjust the volume control. T ry pressing the F11 ke y to see if volume mute is disabled. Check that th e volume control on the computer is tur ned up.
153 If Something Goes Wrong Wireless networking pr oblems The printer will not print what you see on the screen. Many programs display info rmation on the screen differently from the way they print it. See if your pr ogram has a print preview mode. This mode lets you see your wo rk exactly as it will pr int.
154 If Something Goes Wrong Wireless networking pr oblems ❖ Check the Windows ® Control Panel's De vice Mana ger to verify that the Wi-Fi ® adapt er is recognized by the Windows ® operating syst em, and that the driv er is loaded. T o access the Devic e Manager , fr om the Start scre en begin typing Control Panel .
155 If Something Goes Wrong DVD operating problems DVD operating problems If you experience a problem playing DVDs, you may be able to fix the pr oblem yourself. For general pr oblems playing a DVD title, try the following steps: 1 V erify that the disc is in a format that the drive supports.
156 If Something Goes Wrong Develop good computing habits The screen saver runs while you are watching a movie or title. If the screen saver is e nabled, it runs on t op of any movie or title you ar e watching. T o disable the scr een saver: 1 Right-click the de sktop and click Personalize in the menu.
157 If Something Goes Wrong Develop good computing habits Read the documentation. It is very dif ficult to pr ovide a fail-safe set of step s you can follow every t ime you experience a problem with the computer . Y our ability to solve pr oblems will improve as you learn about how the computer and its softwar e work together .
158 If Something Goes Wrong Develop good computing habits 3 In the left pa ne, click or touch System Protection . The System Pr otection tab of th e System Pr operties window appears. 4 Click or touch Configure . 5 Under Restore settings sele ct T urn on System Protection .
159 If Something Goes Wrong Develop good computing habits 7 V erify that the Res tore point you chose is the corr ect one. If it is not, click or touch Ba ck to return to the prev ious step. 8 Close all programs and save all open files. 9 Click or touch Finish , and then Ye s to b egin the system res t o re.
160 If Something Goes Wrong Develop good computing habits For additional Help, w hile in the Windows ® Desktop screen, press the F1 key to launch the Windows ® Help and Support scr een.
161 If Something Goes Wrong Develop good computing habits ❖ Do one installation at a time. If you ha ve several new items to add to y our computer syste m, install just one at a time, cr eating r estor e points immediately befor e each successive installation.
162 If Something Goes Wrong If you need further assistance ❖ If you ar e attempti ng to char ge a devi ce without an AC adaptor connect ed to the computer , the computer 's battery power may be below the limit specified in the TOSHIBA Sleep utility or the battery may be depleted.
163 If Something Goes Wrong Other T oshiba Inter net W eb sites Contacting T oshiba T oshiba’ s T echnical Support W e b site For technic al support, or to stay current on the most recent software and hardware options for y our computer , and for other product informa tion, be sure to regularly chec k the To s h i b a W e b s i t e a t support.
164 If Something Goes Wrong T oshiba’ s worldwide offices For mor e information on additi onal T oshiba worldwide locations, please visit: w ww .toshiba.co .jp/index.htm . Latin America and Caribbean T oshiba Amer ica Information Systems, Inc. 9740 Irvine Boul evard Irvine, California 92618 United State s Mexico T oshiba de México S.
165 5.375 x 8.375 ver 2.3 Appendix A TOSHIBA Function Keys TOSHIBA Function keys provide a quick way to modify selected system functions and to lau nch applications.
166 TOSHIBA Function Keys Functions 5.375 x 8.375 ver 2.3 Help file Display brightness This T O S H I B A Function key displa ys the help file. This T O S H I B A Function ke y decreases the screen brightness. This T O S H I B A Function ke y increases the screen brightness.
167 TOSHIBA Function Keys Functions 5.375 x 8.375 ver 2.3 Output (Display switch) This T O S H I B A Function key cycles through the display options and highlig hts the available options.
168 TOSHIBA Function Keys Functions 5.375 x 8.375 ver 2.3 Disabling or enabling the touch pad Media butt ons V olume Mute This TO S H I B A Function key enables/disables the touch pad. T o enable/disable the to uch pad press F5 . For mor e information on using th e touch pad, see “Using the to uch pad” on page 67 .
169 TOSHIBA Function Keys Functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices Keyboard Function keys Zoom (Display resolution) This TO S H I B A Function key enables/dis ables the Wi-Fi ® antenna in yo ur computer . The wireless modes are: ❖ Disables the wireless antenna (Airplane mode is ON).
170 5.375 x 8.375 ver 2.3 Appendix B Power Cord/Cable Connectors Y our computer ships with the corr ect power supp ly for the country of pur chase. Th is appendix shows the sh apes of the typical AC power c ord/c able connectors for vari ous parts of the world.
171 Glossary TECHNICAL NOTE: Some feat ures defined in th is glossary may no t be available on your computer . Acronyms The following acr onyms may a ppear in this User’ s Guide.
172 Glossary DPI Dots Per Inch DVD Digital V ersatile (or Video) Disc DVD-ROM Digital V ersatile (or Vide o) Disc Read-Only Memory eSA TA external Serial Advanced T echnology Attachment FAT File Alloc.
Glossary 173 RFI Radio Frequency Interference ROM Read-Only Memory RTC Real-Time Clock SD Secure Digital SDRAM Synchronous Dyn amic Random Access Memory SSD Solid Stat e Drive TFT Thin Film T ransisto.
174 Glossary B backup —A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged. Basic Input/Output System (BIOS) —See BIOS . baud rate —The speed at which a communication de vice, such as a prin ter or modem, transmits info rmation.
Glossary 175 C cache —A section of very fast memory in which fr equently used information is duplicated for quick acc ess. Accessing data from cache is faster than accessing it from the computer ’ s main memory . See also CPU cache , L1 cache , L2 cache .
176 Glossary controller —A device that cont rols the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and pr inters all requir e controllers. CPU —See Central Processing Unit (CPU) .
Glossary 177 disc —A ro und, flat piece o f mater ial, designe d to be re ad fro m and written to by optical (laser) t echnology , and used in th e production of optical discs, such as CDs and DVDs.
178 Glossary eSA TA —An exter nal device that supports hot swapping and fast data transf er . V ery usef ul in storing an d transferr ing large files. executable file —A computer pr ogram that is ready to run. Application programs and batch files are examples of executable files.
Glossary 179 Function key —(1) A feature in which ce rtain keys in combination with the Fn key can set system options or control system parameters, such as the battery save mode. (2) A key or combina tion of keys that activates a memory reside nt prog ram.
180 Glossary I icon —A small imag e displayed on the screen that represents a function, file, or prog ram. interlaced —A method of refreshing a computer sc reen, in which only every other line of pi xels is r efr eshed. Inter laced monitors take two pa sses to cr eate a complete scr e en image.
Glossary 181 load —T o move information from a storage device (s uch as a hard disk) into memo ry for processing. local area network —See LAN . logical drive —A section of a disk tha t is recognized by the operating system as a separate dis k drive.
182 Glossary non-interlaced —A method of r efr eshing a co mputer scr een, in which each pixel of every lin e is refr eshed as th e electr on beam scans across and down the screen. Compare interlaced . non-system disk —A disk for stor ing progra ms and data that cannot be us ed to start the co mputer .
Glossary 183 pointer —An icon (usually an arrow) th at moves on the scr een when you slide yo ur finger across the touch pad or mo ve a mouse. Used to point to and sele ct/activate on-s creen items, such as icons , menu items, and butt ons.
184 Glossary RGB (Red, Green, Blue) monitor —A monitor th at repr oduces all colors by mix ing red, green, and blue light in various combinations. RJ45 connector —An eight-wir e connecto r used to conne ct a computer to a n etwork. ROM (Read-Only Memory) —Non-volatile memo ry that can be read bu t not writ ten to.
Glossary 185 system prompt —The symbol (in the MS-DOS ® operating system, generally a drive letter followed by a “greater than” sign) indicating wh ere users are to enter commands.
186 Index A AC adaptor 40 AC power 92 AC power light 40 accessing network 113 adding memory check total memory 56 memory (optional) 48 optional external devices 47 adequate ventilation cooling fan 39 .
187 Index RTC m e mo r y 92 running computer on battery power 90 safety pr ecautions 103 setting notifications 96 taking car e of 103 battery indicator light 95 BIOS Setup see System Settings button e.
188 Index disposing of your computer 104 documentation 30 DVD removing with computer of f 88 removing with computer on 88 DVD player troubleshooting 155 DVDs using 84 E eco power plan 99 eco Utilit y.
189 Index M maintaining your battery 104 manual eject hole optical disc drive 85 media control buttons mute button 86 next track button 86 play/pause button 86 previous track button 86 using 86 volume.
190 Index utility 120 port HDMI™ 72 power connecting cable to AC adaptor 41 cord/cable 42 cord/cable c onnectors 170 ener gy-saving featur es 90 power down shut down 45 power light 95 power manageme.
191 Index customize computer settings 74 display output 73 Shut down computer 45 , 46 , 47 , 49 , 144 icon 45 , 46 , 47 , 49 , 144 Sleep mode 46 Sleep Utilities 127 sounds rec ord in g 113 speake rs u.
192 Index power and batteries 145 printer 15 2 restor e points 157 screen does not look corr ect/ flickers 147 slow Internet connection 141 sound system 152 trouble running discs 151 trouble running p.
デバイスToshiba P40の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Toshiba P40をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba P40の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba P40の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba P40で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba P40を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba P40の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba P40に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba P40デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。