ToshibaメーカーPSLD2Xの使用説明書/サービス説明書
ページ先へ移動 of 201
Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual Toshiba Personal Computer Satellite L350 Satellite Pro L350 EQUIUM L350 SATEGO L350 (PSLD0x/PSLD1x) (PSLD2x/PSLD3x) Mainte.
ii Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual Copyright © 2008 by Toshiba Corporation. All rights reserv ed. Under the copyright laws, this manual cannot be reproduced in any form without the pr ior written perm ission of Toshiba.
Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Compute.
iv Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual The manual is divided into the following parts: Chapter 1 Hardware Overview describe s the Satellite L350 / Satellite Pro L350 / EQUIUM L350 / SATEGO L350 system unit and each FRU.
Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual v Conventions This manual uses the following form ats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition.
vi Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual Table of Contents Chapter 1 Hardware Overview 1.1 Features .............................................................................................................. .
Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual vii Procedure 3 Format Check................................................................................ 2-12 Procedure 4 Test Program Check ............................
viii Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual 3.2.5 Audio Play Test ......................................................................................8 3.2.6 Audio Record Test ..................................
Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual ix Safety Precautions ................................................................................................ 4-2 Before You Begin .................................
x Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual Removing the Wireless LAN Card .................................................................... 4-26 Installing the Wireless LAN Card .................................
Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual xi Removing the CCD and MIC ............................................................................ 4-52 Installing the CCD and MIC ....................................
xii Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ...................
Chapter 1 Hardware Overview.
1 Hardware Overview ii Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual.
1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual iii Chapter 1 Contents 1.1 Features ................................................................................................................... .
1 Hardware Overview iv Satellite L350/Satellite Pro L350/EQUIUM L350/SATEGO L350 Maintenance Manual Figures Figure 1-1 ID Parts Description Placement ............................................................................... 6 Figure 1-2 Computer Block Diagram .
1 Hardware Overview 1.1 Features 2 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual 1.1 Features The Toshiba Satellite L350/Satellite Pro L350/ EQUIUM L350/SATEGO L350 is .
1.1 Features 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 3 The computer has two SO-DIMM slots, which come standard with DDRII-667MHz module. It supports PC2-5300 and uses SO-DIMMs (DDRII SDRAM) driven at 1.
1 Hardware Overview 1.1 Features 4 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual Keyboard The keyboard has 30 kinds’ countries keyboard. Battery The computer has a removable 6/9 Cell Lithiu m Ion battery pack and an internal RTC battery (rechargeable).
1.1 Features 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 5 On-Board LAN The internal LAN supports 10/100Mbit, enabli ng connection to a LAN at up to 100Mbps. It supports Wake-up on LAN from S3/S4/S5 and PXE boot support.
1 Hardware Overview 1.1 Features Figures 1-1/1-2/1-3 and 1-4 show the com puter and its system unit configuration, respectively. Figure 1-1 ID Parts Description Placement 6 Satellite L350/Satellit.
1.1 Features 1 Hardware Overview Figure 1-2 Computer Block Diagram Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 7.
1 Hardware Overview 1.1 Features Figure 1-3 System Board Configurations 8 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual.
.
1.2 System Unit Components 1 Hardware Overview 1.2 System Unit Components Figure 1-4 is Block Diagram of the System Unit. Figure 1-4 System Unit Block Diagram Satellite L350/Satellite Pro L350/EQUIUM .
1 Hardware Overview 1B1.2 System Unit Components 10 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual The system unit of the computer consists of the following com ponents: Processor: Intel Core2 Duo, Dual Core & Merom Celeron Processor.
1.2 System Unit Components 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 11 y 8Mb x 1 chip (1024KB flash parts) − NvStorage Size: 128KB − NvStor.
1 Hardware Overview 1B1.2 System Unit Components 12 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual − Enhanced Power Management − Manageability − System Management Bus (SMBus 2.
1.2 System Unit Components 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 13 Battery EEPROM y 24C02 equivalent (128 words x 16 bits, I2C interfac.
1 Hardware Overview 1B1.2 System Unit Components 14 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual − IEEE 802.11agn y Data Rate − IEEE 802.11g: Standard 54M bps − IEEE 802.11ag: Standard 54M bps − IEEE 802.11agn: Standard 130M bps y Frequency Channel − IEEE802.
2B1.3 2.5-inch HDD 1 Hardware Overview 1.3 2.5-inch HDD The computer contains an extremely low-pr ofile, lightweight and high-perform ance HDD. The HDD incorporates 9.5 mm or 12.5 m m height magnetic disk and m ini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA.
1 Hardware Overview 3B1.4 Combo CD-RW/DVD-ROM 1.4 Combo CD-RW/DVD-ROM The Combo CD-RW/DVD-ROM drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and HS CD-RW at 10x speed and US CD-RW at 24x speed and CD-RW at 4x speed.
4B1.5 DVD Super Multi (+-R Double Layer) 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 17 1.5 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-in ch) and 8-cm (3.15-inch) discs.
1 Hardware Overview 5B1.6 18 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual 1.6 HD DVD ROM The HD DVD ROM drive accepts 12-cm (4.
6B1.7 Power Supply 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 19 1.7 Power Supply The power supply unit provides many different voltages for the system board and perform s the following functions: 1.
1 Hardware Overview 7B1.8 Batteries 20 Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual 1.8 Batteries The computer has the following three types of batteries: Main Battery Pack Real Time Clock (RTC) Battery Table 1-5 lists the specifications of these batteries.
7B1.8 Batteries 1 Hardware Overview Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual 21 Table 1-6 Quick/Normal Charging Time State Charge Time Off-State Charge 6/9 Cell Ab.
2 Troubleshooting 2-i Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2 概要 Chapter 2 Troubleshooting.
2 Troubleshooting 2-ii Sa tellite L350/Satellite Pro L350/EQUIUM L350/SATEGO L350 Maintenance Manual Chapter 2 Contents 2.1 Outline .................................................................................................................... 2-1 2.
2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-iii 2.10 Audio Test ............................................................................................................ 2-21 Procedure 1 Test Program Check .
2 Troubleshooting 2-iv Satellite L350/Satellite Pro L350/EQUIUM L350/SATEGO L350 Maintenance Manual Figures Figure 2-1 Basic Flowchart ............................................................................................. 2-3 Tables Table 2-1 HDD Error Code and Status .
2.1 Outline 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-1 2.1 Outline This chapter describes the fault diagnosis proced ures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1.
2 Troubleshooting 2.2 Basic Flowchart 2-2 Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2.2 Basic Flowchart The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU.
2.2 Basic Flowchart 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-3 Star t Connect the AC Adapter DC IN LED on ?? BATTERY LED on ?? Turn the power on.
2 Troubleshooting 2.2 Basic Flowchart 2-4 Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual Figure 2-1 Basic Flowchart (2/2) Keyboard works well ?? Follow the keyboard diagnostic procedure in Section 2.6 1 N o Insert Bootable CD into ODD Diagnostic Program Loaded ?? Perform each test with the diagnostic program.
2.2 Basic Flowchart 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-5 If the diagnostic program cannot detect an er ror, the error may be interm ittent. Run the continuous test program repeatedly to isolate th e problem.
2 Troubleshooting 2.3 Power Supply 2-6 Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2.3 Power Supply The power supply in the computer controls ma ny functions and com ponents. To check if the power supply is defective or malfunctioning, foll ow the troubleshooting procedures below as instructed.
2.3 Power Supply 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-7 DC IN LED DC IN LED Power supply status On in Green DC power being su pplie d (from the AC adapter) Off Battery damage and can’t charg e duri ng DC-in.
2 Troubleshooting 2.3 Power Supply Procedure 2 Connection Check Power is supplied to the system board as illustrated below: AC adaptor System board AC power cord AC adaptor cord Battery pack Follow th.
2.4 System Board 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-9 2.4 System Board To check if the system board is defectiv e or malfunctioning, f ollow the troubleshooting procedures below as instructed.
2 Troubleshooting 2.4 System Board 2-10 Satellite L350/Satellite Pro L350/EQUIUM L350 /SATEGO L350 Maintenance Manual Procedure 2 Test Program Check The maintenance test program contains seve ral program s for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3.
2.5 2.5-inch HDD 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-11 2.5 2.5-inch HDD To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed.
2 Troubleshooting 2.5 2.5-inch HDD 2-12 Satellite L350/Satellite Pro L350/EQUIUM L350 /SATEGO L350 Maintenance Manual create a DOS partition on drive C. Then restart the computer. If the problem persists, go to Procedure 3. Check 3 If drive C is listed as active in the FDISK menu, perform Check 4.
2.5 2.5-inch HDD 2 Troubleshooting Procedure 4 Test Program Check Run the HDD test program stored on the maintena nce test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed.
2 Troubleshooting 2.5 2.5-inch HDD Procedure 5 Connector Check and Replacement Check The HDD or system board may be faulty. Di sassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connect ors have been firmly connected to the HDD, system board and CPU.
2.6 Keyboard 2 Troubleshooting 2.6 Keyboard To check if the computer’s keyboard is defective or malf unctioning, follow the troubleshooting procedures below as instructed.
2 Troubleshooting 2.7 Display 2.7 Display To check if the computer’s display is def ective or malfunctioning, follow the troubleshooting procedures below as instructed.
2.7 Display 2 Troubleshooting Check 3 The FL may be fault y. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 4. Check 4 The FL inverter board may be fa ulty. Replace it w ith a new one and return to Procedure 3.
2 Troubleshooting 2.8 ODD Drive 2.8 ODD (Optical Disk Drive) To check if the internal ODD drive is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 ODD Cleaning Check 1.
2.8 ODD Drive 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-19 Check 3 The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functio n ing properly, perform Check 4.
2 Troubleshooting 2.9 LAN 2-20 Satellite L350/Satellite Pro L350/EQUIUM L350 /SATEGO L350 Maintenance Manual 2.9 LAN To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed.
Error! Reference source not found.E rror! Reference source not found. Audio Test 2 Troubleshooting 2.10 Audio Test To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed.
2 Troubleshooting 2.11 Cooling Module 2.11 Cooling Module To check if the computer’s cooling module is defective or malfunctioning, f ollow the troubleshooting procedures below as instructed.
2.11 Cooling Module 2 Troubleshooting Satellite L350/Satellite Pro L350 /EQUIUM L350/SATEGO L350 Maintenance Manual 2-23.
Chapter 3 Diagnostic Programs.
3 Diagnostic Programs ii Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual Chapter 3 Contents 3.1 General ....................................................................................................................
3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual iii 3.8 Video ........................................................................................................................... 44 3.9 Communication (COMM) .
.
3.1 General 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 1 3.1 General This chapter explains the dia gnostic programs which tests and di agnoses the functions of the hardware components of this computer.
3 Diagnostic Programs 3.1 General 2 Satellite L350,Satellite Pro L350, EQUIUM L350,SAT EGO L350 Main tenance Manual A Formatted FLOPPY DISK A Test Media CD (A-BEX TEST CD-R OM TCDR-702)(for CD.
3.2 Quick Start 3 Diagnostic Programs 3.2 Quick Start When the system is booting from Service Diagnos tic CD, the following screen will be displayed: Please select a test item or select 0 to exit to Free -DOS: 3.2.1 Quick Test When this item is selected, the syste m will run the configured test item s and generate a test report automatically.
3 Diagnostic Programs 3.2 Quick Start Select ‘Test Mouse’ or press F8 to run the test. The prompt inform ation would be displayed in the screen as below.
3.2 Quick Start 3 Diagnostic Programs Here is another method to run the test: Highl ight a test item by us ing arrow keys, then, press Enter to start. If there are parameters pr ovided, user should set para meters in the parameter dialog window. CPU Speed Test (Step by Step): 1.
3 Diagnostic Programs 3.2 Quick Start 3. Test Result System will automatically run and display the tes t result as follows: Following is the comparison report of the two testing methods m entioned abo.
3.2 Quick Start 3 Diagnostic Programs As to the method adopted in CPU Speed test , user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time.
3 Diagnostic Programs 3.2 Quick Start It requires user to press the key and ch eck whether the key in the screen changes color or not. User can terminate test by typing ‘ END ’. When testing the ‘ Fn ’ key, it must press the ‘ Esc ’ key at the same time.
3.2 Quick Start 3 Diagnostic Programs 3.2.6 Audio Record Test Check whether the system could record the sound normally. If there is no error during the whole test, Pass; otherwise Fail. The test wi ll repeat for four tim es. When the test is completed, a file named autest.
3 Diagnostic Programs 3.2 Quick Start In this screen, all lines which attrib ute could be edited and updated. The 1 st line (the font in yellow with blue background) shows the attr ibute’s value tha.
3.2 Quick Start 3 Diagnostic Programs NOTE: Setup All of DMI Informati on in Type is Max 32 Digital The attributes that have been modified woul d be marked in red; otherwise in yellow. User could press F2 to save the changes, or press F4 to ignore and exit the current program.
3 Diagnostic Programs 3.2 Quick Start User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current pr ogram. On the left column, the components information is listed and us er can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component.
3.2 Quick Start 3 Diagnostic Programs 3.2.11 Exit to Free DOS Select this item to exit to Free DOS. 3.2.12 The Diagn ostics Screen Explanation Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progress Bar, Erro r L ist, Test Item’s Title, Status Bar and Message Box.
3 Diagnostic Programs 3.2 Quick Start The error list of each test m odule is displayed at the lower rig ht corner of the screen. It would display the total error quantity found in the test, the most recent five error co des and description would be shown here.
3.2 Quick Start 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 15 Script File Name : Script file nam e, e.g. ‘ Custom .INI’ in the above screen; Current Time(C. TIME) : Current system time, e.
3 Diagnostic Programs 3.3Option 3.3 Options 3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s param eters and t hose parameters created by the L OG file. Options Menu Notes: • Select All/None Items Switch between selecting a ll test items and selecting none.
3.3 Option 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 17 Configure batch parameters and a ll the test item’s param eters . • Load Batch Parameters Upload all the test items and the param eters to the *.
3 Diagnostic Programs 3.3Option • Test Order Specify the order of the test items. C hoose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence. • Test Options Choose one of the following options: 9 Wait On Error Wait for further confirmation while an error occurs.
3.3 Option 3 Diagnostic Programs Monitor the remaining ba ttery capacity (percent). 9 Monitor CPU Thermal Monitor the CPU temperature. • Test Mode 9 LOOPBOUND The chosen test items will run repeated ly accord ing to the times specified in the 'Number of Loops'.
3 Diagnostic Programs 3.3Option Repeat times of the test item. • Interactive If the item is enabled during the test, the te s t items that need user to response can run normally, such as PS2 Mouse te st; If it is disabled, thos e test item s will report FAIL.
3.3 Option 3 Diagnostic Programs In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files.
3 Diagnostic Programs 3.3Option 3.3.6 LOG Parameters Setting You can access the Log Parameters screen through Service DiagnosticsOptions - Generate Report.
3.3 Option 3 Diagnostic Programs If selecting this parameter, erro rs and time will be recorded only when the test fails. 9 Append to Old Log File If selecting this parameter, the new lo g will be added to the old one. 9 Log Device Info on Fail If selecting this parameter, deta ils of the failed test will be reco rded.
3 Diagnostic Programs 3.3Option In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: • ↑ , ↓ Scroll a line backward or forward on the screen.
3.3 Option 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 25 Scroll a page backward or forward on the screen. • Esc Exit the Log viewer. • F1 Display the Help information about the Log viewer operations and the functional keys.
3 Diagnostic Programs 3.3Option 26 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual Base Memory Test : PASS Extended Memory Test : PASS End Time: Wed Jul 05 10:47:51 2006 <Module Name>: Service Diagnostic Ver 1.00 .
3.4 Subtests 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 27 3.4 Subtests Test Group Sub Item ID Subtest Test ID Test items Internal Name System.
3 Diagnostic Programs 3.4 Subtests 28 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 02 Random Increment Read/Write [RandIncr] 11 Data Bus Test [DataBus] 12 Memory Spee.
3.4 Subtests 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 29 VESA 1024x768x32 K Mode VESA 1024 x 768 x 16 K Mode VESA 1024 x 768 x32bit Mode [V1.
3 Diagnostic Programs 3.5 System Test 3.5 System Test Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item.
3.5 System Test 3 Diagnostic Programs CPU Speed Comparison --Whether you want to make a comparison of the CPU speed with the value set in ‘E xpected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’. Expected CPU Speed --Specify the expected CPU Speed value you want for further comparison.
3 Diagnostic Programs 3.5 System Test 32 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 6. MMX The test item is to confirm whether the CPU supports MMX instru ctions. Subtest 02 Boards 1. DMA Controller This test item is to check whethe r the DMA controller works norm ally.
3.5 System Test 3 Diagnostic Programs parameter setting dialog window. Set the range of Speed that is to be tested, then choose the OK button to test it.
3 Diagnostic Programs 3.6 Memory Test 3.6 Memory Test This test module is to check whet her the m em ory chip works normally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that in cludes two sub-items -- ROM Read and ROM Write Protection.
3.6 Memory Test 3 Diagnostic Programs Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m emory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested.
3 Diagnostic Programs 3.6 Memory Test 36 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below. Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL.
3.6 Memory Test 3 Diagnostic Programs In addition to the above pattern test of th e memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test. Test Range: Specify the test coverage range of Extended Memory.
3 Diagnostic Programs 3.6 Memory Test The test item is to ensure that there is no short circuitry issue in mem ory chip. The parameter dialog window is the same as that in ‘Subtest 02 P attern’. Subtest 06 Walking 0’s Test The test item is to ensure that there is no open circuitry issue in memory chip.
3.6 Memory Test 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 39 This test item is to check whether the data bus works normally. Subtest 12 Memory Speed Test This test item is to check the data -transferring rate for the ca che memory and the system memory.
3 Diagnostic Programs 3.7 Storage 3.7 Storage Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified before the HDD test. The screen is as follows: Password : hard disk 1.
3.7 Storage 3 Diagnostic Programs LBA Start, LBA End --Specify the start and end byte in LBA (Large Block Address). Percent —Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested.
3 Diagnostic Programs 3.7 Storage Percent-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested.
3.7 Storage 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 43 Subtest 02 ODD The ODD test runs on ID E CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and perf ormance. 1.
3 Diagnostic Programs 3.10 Peripheral 3.8 Video This test item tests the video by: 1. displaying the figures in different graphic modes. 2. displaying the property and color of the characters in different text modes. User will confirm whether each video m ode works normally by judging whether the display is correct.
3.10 Peripheral 3 Diagnostic Programs It would display the below texts of th e different attributes in the screen: 1. Text in normal attribute; 2. Text in blinking normal attribute; 3. Text in inverse attribute; 4. Text in blinking inverse attribute; 5.
3 Diagnostic Programs 3.10 Peripheral 4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode.
3.10 Peripheral 3 Diagnostic Programs This test item is to check whether 80*25 Text Mode works normally. In the test, user is required to respond according to the instru ction in the screen. Subtest 02 640 * 480 VGA Mode This test item is to check whethe r 680*480 VGA Text mode works normally.
3 Diagnostic Programs 3.10 Peripheral Subtest 03 VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respon d following the instruction in the screen. 1. 640X480 Video Modes Test 2.
3.10 Peripheral 3 Diagnostic Programs If press Ctrl+Break to force the test to term inate during execution of VESA Video Memory, the test program will not operate and display properly in f urther tests. Subtest 05 AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally.
3 Diagnostic Programs 3.10 Peripheral Subtest 07 Register Test This test item is to check whether th e registers of the video adapter works normally. Subtest 08 Color Purity Test This test item is to check whether th e sy stem (the video adapter and the display) could display the purity color of re d, green, blue, black and white.
3.10 Peripheral 3 Diagnostic Programs Subtest 09 Direct Color Test This test item is to check the video adap ter ’s composing ability of direct color in high and true color mode. In the test, user is required to respond according to the instru ction in the screen.
3 Diagnostic Programs 3.10 Peripheral NOTE 1:AMD platform can’t support this item Subtest 11 BitBlt Engine Test This test item is to check whether th e BitBlt engine works norm ally.
3.10 Peripheral 3 Diagnostic Programs NOTE 1:AMD platform can’t support this Test item Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 53.
3 Diagnostic Programs 3.10 Peripheral 54 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 3.9 Communication (COMM) Subtest 01 LAN Card This test item is to check whether the m odule can detect the exis tence of the network card and display its related information.
3.10 Peripheral 3 Diagnostic Programs 3.10 Peripheral Subtest 01 Keyboard This test item is to check wh ether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Clock Line Test Check whether the keyboard clock line works normally.
3 Diagnostic Programs 3.10 Peripheral Subtest 03 Led Test 1. Led Test Check whether the Device led works normally. NOTE 1:If The Machine is AMD Pl atform, The HDD LED is very Dim 56 Satellite L350,Sat.
3.11Error Codes and Description 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 57 3.11 Error Codes and description The format of ‘Error Code’ .
3 Diagnostic Programs 3.11Error Codes and Description 58 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 04 (XMS)Mem ory Problem The test pattern read out from the extension memory is different from the one that has been written in this address.
3.11Error Codes and Description 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 59 configuration. 17 PCI to ISA Bridge Error PCI-ISA bridge errors. Repeat multiple times. If there is always the same error, replace the board.
3 Diagnostic Programs 3.11Error Codes and Description 60 Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 15 VESA VRAM Test Error Physical problems with the video card or the monitor. Check whether there is any physical problem with the video card or the monitor.
3.11Error Codes and Description 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 61 01 Keyboard Map & Stroke Test Fail Keyboard Map & Stroke Test fails. Check the KBD connection and repeat the test.
.
3.12 Quick Test Item List 3 Diagnostic Programs Satellite L350,Satellite Pro L350, EQUIUM L350,SATEGO L350 Main tenance Manual 62 3.12 Quick Test Item List Device Test Items Comment CPU Basic Function.
Chapter 4 Replacement Procedures 4 1.
4 Replacement Procedures 4-ii Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual.
4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-iii Chapter 4 Contents 4.1 General ............................................................................................................
4 Replacement Procedures 4-iv Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the Keyboard ...................................................................................... 4-23 4.5 MDC Module .........
4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-v Removing the FL Inverter Board ....................................................................... 4-47 Installing the FL I nverter Board .
4 Replacement Procedures 4-vi Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Figures Figure 4-1 Removing the battery pack ................................................................................. 4-8 Figure 4-2 Removing the PC card .
4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-vii Figure 4-31 Removing CCD board and MIC ...................................................................... 4-52 Figure 4-32 Removing the speakers .
4.1 General 4 Replacement Procedures 4 1 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures m ay not require you to remove all the surrounding FRUs to replace only one FRU.
4 Replacement Procedures 4.1 General 4-2 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Safety Precautions Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-3 CAUTION: 1. Before replacing a component, make su re that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications.
4 Replacement Procedures 4.1 General 4-4 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Before You Begin Before you begin to disassembly the computer, keep in m ind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-5 Disassembly Procedures The cable connectors come in these two basic types: .
4 Replacement Procedures 4.1 General 4-6 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipm ent.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-7 Colors of Screw Shanks For easy identification of the correct screws, the scre.
4 Replacement Procedures 4.1 General Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-9 Installing the Battery Pack Install the battery pack according to the following procedures and Figure 4-1.
4 Replacement Procedures 4.1 General Removing the Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are using.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-11 Installing the Optional PC Card Install the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode.
4 Replacement Procedures 4.1 General Removing the Memory Card Remove the mem ory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Push the memory card to be rem oved until it stops then release the mem ory card.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-13 Installing the Memory Card Install the memory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode.
4 Replacement Procedures 4.1 General Removing the Optional Memory Remove the optional mem ory (module) according to the following procedures and Figures 4- 4, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer.
4.1 General 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-15 Installing the Optional Memory Install the optional memory (m odule) according to the following procedures and Figures 4-4, after checking that the computer is turned off in boot mode.
4 Replacement Procedures 4.2 HDD 4.2 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4-5, 4- 6.
4.2 HDD 4 Replacement Procedures 3. Remove the HDD pack by pulling on the tab attached to the pack, following the direction of the arrows. NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails.
4 Replacement Procedures 4.2 HDD 4-18 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the HDD Install the HDD according to the following procedures and Figures 4-5, 4-6. CAUTION: To avoid damage, always hold the HDD only by its sides.
4.3 ODD Bay Module 4 Replacement Procedures 4.3 ODD Bay Module Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules.
4 Replacement Procedures 4.3 ODD Bay Module 4-20 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the ODD Bay Module Install the ODD bay module according to the following procedures and Figures 4-7. 1. Place the ODD bay module in the correct position and slide it in.
4.3 ODD Bay Module 4 Replacement Procedures Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-8.
4 Replacement Procedures 4.4 Keyboard 4.4 Key board Removing Keyboard Remove the Keyboard according to the following procedures and Figure 4-9. 1. Release the following 12 latches on the keyboard cover, in that order: - One left latch - Five bottom latches - Six front latches 2.
4.4 Keyboard 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-23 Installing the Keyboard Install the keyboard according to the following procedures and Figure 4-9. 1. Connect the keyboard cable to CN11 on the system board.
4 Replacement Procedures 4.5 MDC Module 4.5 MDC Module Removing the MDC Module Remove the MDC Module (Modem Daughter Card) according to the following procedures and Figures 4-10, after checking that the computer is turned off in boot mode. CAUTION : Remove the MDC module after turning off the computer.
4.5 MDC Module 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-25 Installing the MDC Module Install the MDC module according to the following procedures and Figures 4-10, after checking that the computer is turned off in boot mode.
4 Replacement Procedures 4.6 Wireless LAN card 4.6 Wireless LAN Card Removing the Wireless LAN Card Remove the wireless LAN card according to the following procedures and Figure 4-11. CAUTION : Do not touch the connectors on the wireless LAN card and in the computer with your bare hands.
4.6 Wireless LAN Card 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-27 Installing the Wireless LAN Card Install the wireless LAN card according to the following procedures and Figure 4-11. 1.
4 Replacement Procedures 4.7 Top Cover 4 1 4.7 Top Cover Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-12 and 4-13. 1. Turn the computer upside down and remove the following 23 screws: - Eighteen M2.5x7 black flat head screws and three M2x4 black flat head screws.
4.7 Top Cover 4 Replacement Procedures Latch Power board cable Touch pad board flat cable Switch board flat cable Speakers cable Top cover CN8 CN9 CN1 CN2 Figure 4-13 Removing the top cover Installing the Top Cover Install the top cover with the display assembly according to the following procedures and Figures 4-12, 4-13.
4 Replacement Procedures 4.7 Display Assembly 4.8 Display Assembly Removing the Display Assembly CAUTION : Use care to avoid that the antenna cable is not caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-14, 4-15.
4.7 Display Assembly 4 Replacement Procedures M2 5x7 black flat head screw . LCD FL cable CCD cable MIC cable Wireless LAN antenna CN5 CN7 CN13 Figure 4-15 Removing the display assembly Installing the Display Assembly and ODD Extended Board Install the display assembly according to the following procedures and Figures 4-14, 4-15.
4 Replacement Procedures 4.9 System Board, AC-IN Cable and ODD Extended Board 4.9 System Board, AC-IN Cable and ODD Extended Board Removing the System Board, AC- IN Cable and ODD Extended Board NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board.
4.9 System Board, AC-IN Cable and ODD Extended Board 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-33 Installing the System Board, AC-IN Cable and ODD Extended Board Install the System Board, AC-IN Cable and ODD Extended Board according to the following procedures and figure 4-16.
4 Replacement Procedures 4.10 CPU Cooling Module and Fan 4-34 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4.10 CPU Cooling Module and Fan CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation.
4.10 CPU Cooling Module and Fan 4 Replacement Procedures M2 5x5 white flat head screw . Fan Tape CN501 Figure 4-17 Removing the fan M2x3 white flat head screw CPU cooling module bracket CPU cooling mo.
4 Replacement Procedures 4.10 CPU Cooling Module and Fan Figure 4-19 Applying silicon grease Installing the CPU Cooling Module and Fan(For Intel CPU) Install the cooling Module according to the following procedures and Figures 4-17, 4-18 and 4-19. CAUTION: When installing the cooling module, keep the following in mind: 1.
4.10 CPU Cooling Module and Fan 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4-37 CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation.
4 Replacement Procedures 4.10 CPU Cooling Module and Fan M2 5x5 white flat head screw . Fan Tape CN501 Figure 4-20 Removing the fan M2x3 white flat head screw CPU cooling module bracket CPU cooling mo.
4.10 CPU Cooling Module and Fan 4 Replacement Procedures Figure 4-22 Applying silicon grease Installing the CPU Cooling Module and Fan(For AMD CPU) Install the cooling Module according to the following procedures and Figures 4-20, 4-21 and 4-22. CAUTION: When installing the cooling module, keep the following in mind: 1.
4 Replacement Procedures 4.11 CPU 4.11 CPU Removing the CPU Remove the CPU according to the following procedures and Figures 4-23, 4-24 and 4-25. CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation.
4.11 CPU 4 Replacement Procedures Installing the CPU Install the CPU according to the following procedures and Figures 4-24, 4-25. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket.
4 Replacement Procedures 4.11 CPU 3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. NOTE: FOXCONN CPU socket will be 180 degrees to the left.
4.12 Broadcom Card 4 Replacement Procedures 4.12 Broadcom Card Removing the Broadcom Card Remove the Broadcom card according to the following procedures and Figure 4-26. CAUTION: Do not touch the connectors on the Broadcom card and in the computer with your bare hands.
4 Replacement Procedures 4.12 Broadcom Card 4-44 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the Broadcom Card Install the Broadcom card according to the following procedures and Figure 4-26. 1. Insert the Broadcom card into the connector an angle of 45 degrees.
4.13 Display Mask 4 Replacement Procedures 4.13 Display Mask Removing the Display Mask Remove the display mask according to the following procedures and Figure 4-27. 1. Remove the following 4 seals on the display module in that order: - Two black seals on the bottom - Two black seals on the top 2.
4 Replacement Procedures 4.13 Display Mask 4-46 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the Display Mask Install the display mask according to the following procedures and Figure 4-27.
4.14 FL Inverter Board 4 Replacement Procedures 4.14 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figures 4-28. 1. Remove one M2.5x5 black flat head screw. M2x4 black flat head screw M2 5x5 black flat head screw .
4 Replacement Procedures 4.14 FL Inverter Board 4-48 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figures 4-28.
4.15 LCD Module 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4 - 49 4.15 LCD Modules NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module.
4 Replacement Procedures 4.15 LCD Module M2x3 black flat head screw M2 5x5 black flat head screw . Left LCD bracket Right LCD bracket LCD module Top LCD bracket M2 5x5 black flat head screw . M2x3 black flat head screw M2x3 black flat head screw Figure 4-29 Removing the LCD module and screws 6.
4.15 LCD Module 4 Replacement Procedures Installing the LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the LCD module according to the following procedures and Figures 4-29, 4-30. 1. Turn the LCD upside down.
4 Replacement Procedures 4.16 CCD Board and MIC 4.16 CCD Board and MIC Removing the CCD Board and MIC Remove the FL inverter board according to the following procedures and Figure 4-31. 1. Remove the CCD module with CCD cable from display rear cover. 2.
4.16 CCD Board and MIC 4 Replacement Procedures Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual 4 - 53 Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-31.
4 Replacement Procedures 4.17 Speakers 4.17 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4-32. 1. Remove two M2x3 black flat head screw securing the left speaker. 2. Remove two M2x3 black flat head screws securing the right speaker.
4.18 Power Button Board and Switch Board 4 Replacement Procedure s 4.18 Power Button Board and Switch Board Removing the Power Button Board and Switch Board Remove the Power Button Board and Switch Board according to the following procedures and Figures 4-33.
4 Replacement Procedures 4.18 Power Button Board and Switch Board 4-56 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Install the Power Button Board and Switch Board Install the Power Button Board and Switch Board according to the following procedures and Figures 4-33.
4.19 Touch Pad and Button Board 4 Replacement Procedure s 4.19 Touch Pad and Button Board Removing the Touch Pad and Button Board Remove the touch pad and button board according to the following procedures and Figure 4- 34. 1. Disconnect the touch pad flat cables from CN5000 on the button board and touch pad.
4 Replacement Procedures 4.19 Touch Pad and Button Board 4-58 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the Touch Pad and Button Board Install the touch pad and button board accordi ng to the following procedures and Figure 4-34.
4.20 USB Cable, CRT Cable and RJ11 Cable 4 Replacement Procedure s 4.20 USB cable, CRT cable and RJ11 Cable Removing the USB cable, CRT cable and RJ11 Cable Remove the USB cable, CRT cable and RJ11 Cable according to the following procedures and Figure 4-35.
4 Replacement Procedures 4.20 USB Cable, CRT Cable and RJ11 Cable 4-60 Satellite L350/ Satellite Pro L 350/ EQUIUM L350/ SATEGO L350 Maintenance Manual Installing the USB cable, CRT cable and RJ11 Cable Install the USB cable, CRT cable and RJ11 Cable according to the following procedures and Figure 4-35.
6000 1 次 Appendices.
Appendices App-ii Satellite L350/Satellite Pro L350/EQUIUM L 350/SATEGO L350 Maintenance Manual Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout .
Appendices Satellite L350/Satellite Pro L350/EQUIUM L350/ SATEGO L350 Maintenance Manual App-iii C.24 CN508 Bri dge Media Slot Connector (21-Pin) ............................................ C-17 C.25 CN510 Broadcom Decoder Connector (52-Pin) ........
デバイスToshiba PSLD2Xの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Toshiba PSLD2Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba PSLD2Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba PSLD2Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba PSLD2Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba PSLD2Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba PSLD2Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba PSLD2Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba PSLD2Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。