ToshibaメーカーPT311U04E07Kの使用説明書/サービス説明書
ページ先へ移動 of 246
GMAD00257010 04/10 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 177 in this gui de.
2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical ap.
4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n.
5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can.
6 5.375 x 8.375 ver 2.3 In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer . Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment.
7 5.375 x 8.375 ver 2.3 3 The standard connecting arrangemen t (telephone jack type) for this equipment is jack t ype(s): USOC RJ11C. Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card.
8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health W ireless LAN products, like other radio de vices, emit radio frequency electromagnetic energy . The lev el of energy emitted by W i reless LAN devices howe ver is f ar much less than the elect romagnetic energy emitted by wireless devices lik e for example mobile phones.
9 5.375 x 8.375 ver 2.3 Canada – Indust ry Canada (IC) This device complies with RS S 210 of Industry Canada. The installer of this radio equipment mu st ensure that the antenna is located or pointe.
10 5.375 x 8.375 ver 2.3 EU Declaration of Conformity TOSHIB A declares that this product conforms to the follo wing Standards: This product is carrying the CE-Mark in accordance w ith the related European Directiv es. The party responsib le for CE-Marking is TOSHIB A Europe GmbH, Hammfelddamm 8, 41460 Neuss, Ger many .
11 5.375 x 8.375 ver 2.3 VCCI Class B Information Modem W arning Notice This information is only applicable if your computer has a modem. Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN).
12 5.375 x 8.375 ver 2.3 Using this Equipment in Japan In Japan, the frequency bandwi dth of 2,400 MHz to 2,483.5 MHz for second generation low-po wer data communicatio n systems such as this equipment ov erlaps that of mobile object identifi cation systems (premises radio station and specified lo w-power radio station).
13 5.375 x 8.375 ver 2.3 The indication sho wn belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.
14 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on what type of wi reless de vice is in your computer .
15 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 622ANHMW and 633ANHMW Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
16 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Atheros ® Wireless Wi-Fi ® Link AR5B95 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
17 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Ukraine United Kingdom Uruguay USA V enezuela V ietnam Y emen Zimbabwe België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special reg istration with IB PT/BIPT is required.
18 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply .
19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8192E This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8191SE This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
22 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that.
23 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table.
24 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnology and Y our Health The products with Bluetooth ® wireless technolog y , like other radio de vices, emit radio frequency electromagnetic ener gy .
25 5.375 x 8.375 ver 2.3 Regulator y statements This product complies with any mandatory product specification in any country/ region where the product is sold.
26 5.375 x 8.375 ver 2.3 Optical Disc Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model properl y , read th e user’ s guide carefully and keep it for your fut ure reference.
27 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approv al of the U.S. Department of Commerce prior to export.
28 5.375 x 8.375 ver 2.3 T rademarks Portégé and eco Utility are either registered trademarks or trademarks of T oshiba America Information Systems, In c. and/or T oshiba Cor poration. Adobe and Photoshop are either registered trademarks or tr ademarks of Adobe Systems Incorporated in the Unite d States and/or other countries.
29 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 37 This guide ...............................................................39 Safety icons ............................
30 Contents 5.375 x 8.375 v er 2.3 Using the computer fo r the first time ......................49 Opening the display panel ................................. 49 Turning on the power .......................................50 Setting up your software .
31 Contents 5.375 x 8.375 v er 2.3 Using a mouse ........................................................83 Connecting a printer ...............................................83 Setting up a printer ...........................................84 Turning off the computer .
32 Contents 5.375 x 8.375 v er 2.3 Using the optical disc drive ................................... 107 Optical disc drive components ........................ 107 Inserting an optical disc ................................. 108 Playing an audio CD ....
33 Contents 5.375 x 8.375 v er 2.3 Disposing of used batteries ..................................129 Traveling tips ........................................................ 131 Chapter 4: Exploring Y our Co mputer’ s Features ................... 132 Exploring the desktop .
34 Contents 5.375 x 8.375 v er 2.3 TOSHIBA Security Assist ......................................156 TOSHIBA PC Diagnostic Tool Utility ...................... 158 TOSHIBA HDD Protection Utility ...........................159 Mouse Utility ............
35 Contents 5.375 x 8.375 v er 2.3 Memory problems ................................................184 Power and the batteries ........................................ 184 Keyboard problems ...............................................186 Display problems .
36 Contents 5.375 x 8.375 v er 2.3 Sleep mode .....................................................214 Hibernation mode ........................................... 215 Output (Display switch) .................................216 Display brightness ...
37 5.375 x 8.375 ver 2.3 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our computer model may be ENERGY ST AR ® qualified.
38 Introd uctio n 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 30% and 60% less energ y depending on how it is used.
39 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated.
40 Introd uctio n Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data.
41 Introduction Other documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are de signed to accommodate all possible configurations for an entire product Series.
42 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information.
43 Getting Started Selecting a place to work T o keep your computer in prime operating condition, protect you r work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
44 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin.
45 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer .
46 Getting Started Connecting to a power so ur ce Please handle your computer carefully to avo id scratching or damaging the surface. Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery .
47 Getting Started Connecting to a po wer sour ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to t.
48 Getting Started Char ging the main battery The computer’ s main battery light gives you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng ch.
49 Getting Started Using the computer for the f irst time Using the computer for the first time The computer is now ready for you to turn it on and be gin using it. Opening the display panel 1 Facing the front of the com puter, locate the center of the display panel.
50 Getting Started Using the computer for the fir st time T urning on the power T o turn on the computer: 1 Make sure an y external de vices (such as the A C adaptor , if you plan to use AC po wer rather th an battery power) are properly connected and ready .
51 Getting Started Re gistering your computer with T oshib a Registering your computer with T oshiba Product registration is strongly reco mmended, and allows T oshiba to send you periodic updates, announcement s, and special offers applicable to your p roduct.
52 Getting Started Adding memory (optional) Before adding external devices or memory , T oshiba recommends setting up your software. See “Setting up your s oftware” on page 50 . Installing a memory module Memory modules can be installed in the memory mo dule slots on the base of the computer .
53 Getting Started Adding memory (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start . (Sample Image) Shut down button 2 Click the Shut do wn button in the lower -right corner of the Start menu. The computer closes all open programs, shuts down the operating system, and then turns off.
54 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre ws that secure the memory module slot cover . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cov er .
55 Getting Started Adding memory (optional) If your system has the memory modules stacked on top of one another , you must remove the top module first before removing/installing the bottom module. For this model, Slot A is the bottom slot. Slot B is the top slot.
56 Getting Started Adding memory (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module.
57 Getting Started Adding memory (optional) 15 Re-insert the main battery . For more information on inserting the main battery , see “Inserting a char ged battery” on page 127 . 16 T urn the computer right side up. Make sure to remov e the soft cloth from the work surface be fore restarting the computer .
58 Getting Started Adding memory (optional) Do not try to remove a memor y module with the computer turned on. Y ou can damage the computer and the memor y module. Do not remove the memory module while the computer is in Sleep or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost.
59 Getting Started Adding memory (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screws.
60 Getting Started Recovering the Internal Stor age Drive TECHNICAL NOTE: Y ou must have at least one memor y module installed for the computer to work. Checking total memory When you add or remove a memory mo d u l e , you can check that the computer has recognized the change.
61 Getting Started Recovering the Internal Stora ge Drive A recov ery image of your computer is stored on the internal storage dri ve, and the image can be restored b y running the recovery utilities directly f rom your internal storage dri ve as described in the sections below .
62 Getting Started Recovering the Internal Stor age Drive Recovering to out-of-box state (recommended recovery method) Recoverin g an internal storag e driv e to its out-of-box state deletes all partitions on the drive and all info rmation stored in those partitions.
63 Getting Started Recovering the Internal Stora ge Drive (Sample Image) W arning screen 5 When the T oshiba Recov ery W i zard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
64 Getting Started Recovering the Internal Stor age Drive (Sample Image) Reco very of F a ctory Default Software scr een 7 Click Next . A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to sa ve your work to e xternal media before proceeding (see “Backing up your work” on page 106 ).
65 Getting Started Recovering the Internal Stora ge Drive The “Recov er to a custom size pa rtition” option restores you r C: dri ve to its out-of-box state, and allows you to specify the size for the C: partition.
66 Getting Started Recovering the Internal Stor age Drive (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
67 Getting Started Recovering the Internal Stora ge Drive 8 Click Next . A confirmation message displays reminding you that all data will be lost during the recov ery process. Be sure to sav e your work to e xternal media before proceeding (see “Backing up your work” on page 106 ).
68 Getting Started Recovering the Internal Stor age Drive 4 A warning screen appears stating that when the recovery is ex ecuted all data will be deleted and rewritten.
69 Getting Started Recovering the Internal Stora ge Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover without changing the hard drive partitions . (Sample Image) Reco very of F a ctory Defa ult Software scr een 7 Click Next .
70 Getting Started Recovering the Internal Stor age Drive When you create recovery DVDs/media, only the operating system files, applications, and drivers originally shipped with the computer are backed up to the external media and can be res tored from this media.
71 Getting Started Recovering the Internal Stora ge Drive Y ou cannot store your system’ s applications on the same drive or disc/disc set where the rest of the system recovery files are stored. For example, you will need to store the applications on one USB flash drive and the system recover y files on another USB flash drive.
72 Getting Started Recovering the Internal Stor age Drive Restoring from recovery DVDs/media The recovery process deletes information stored on the internal storage drive. Be sure to save your work to ex ternal media before executing the recovery (see “Backing up your work” on page 106 ).
73 Getting Started Recovering the Internal Stora ge Drive 3 T urn on your computer . When the ini tial screen displays, press F12 . The boot menu di splays. 4 Using the arro w keys, select the D VD option or the USB Flash option, depending on which type of medi a you are using, and then press Enter .
74 Getting Started Erasing the Internal Stora ge Drive Erasing the Internal Storage Drive Erasing the internal storage drive will delete all data on the drive, including the partitions. Be sure to create recovery DVDs/media and back up your data to external media before erasing the internal storage drive.
75 Getting Started Checking the internal stor age drive oper ating status purposes. This process may take several hours, depending on the size of your internal storage dri ve. (Sample Image) Er ase the har d disk scr een 4 Click Next . A confirmation message displays reminding you that all data on the internal storage driv e will be lost.
76 Getting Started Using the T ouchP ad™ Installing drivers and applications The T osh iba Application Installer allows you to reinstall the drivers and applications that were original ly bundled with your computer .
77 Getting Started Using the T ouchP ad™ Refer to the table below for specif ic instructions on perf orming each operation. The pointer is the icon (usually an arrow) that moves on the screen when you slide your finger across the T ouchPad or move a mouse connected to your computer .
78 Getting Started Using the T ouchP ad™ Scroll vertically Slide your finger along the right edge of the T ouchPad in the direction you want to scroll.
79 Getting Started Using the T ouchP ad™ Adjusting T ouchPad™ settings While you are typing, the on-screen pointer may seem to move or jump around “by itself” to ran dom locations on the screen. The on-screen pointer may also seem to automatical ly select text, click buttons, and activ ate other user interface elements.
80 Getting Started Using external display de vices T ouchPad setting options vary by computer model. The T ouchPad settings are accessible through the Mou se Properties option of the Windows Control Panel. For more information, please visit www .support.
81 Getting Started Using external display de vices Selecting video cables T o connect a device to the HDMI™ O ut port, you must purchase an HDMI™ cable.
82 Getting Started Using external display de vices Directing the display output when you turn on the computer Once you ha ve connected an e xte rnal displa y devi ce, you can choose to use the internal display only , the external device only , or both simultaneo usly .
83 Getting Started Using an external k e yboard Adjusting the quality of the external display T o obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
84 Getting Started T urning off the computer T o connect a printer to your computer: 1 Connect the printer cable to th e printer and then connect the other end to one of the computer’ s USB ports. 2 Plug the printer’ s power cable into a li ve A C outlet.
85 Getting Started T urning off the computer It is a good idea to turn of f your computer when you are not using it for a while. If you are using the computer for the first time, lea ve the computer plugged into a power source (e ven though the computer is off) to fully charge the main battery .
86 Getting Started T urning off the computer ❖ Restarting from Hib ernation takes a little m ore time and consumes more main b attery po wer than restarting from Sleep. ❖ When starting up again, the computer returns to the state in which you left it, including all open programs and files you were using.
87 Getting Started T urning off the computer Using the Shut down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns of f your computer .
88 Getting Started T urning off the computer 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. (Sample Image) Edit Plan Settings screen 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears.
89 Getting Started T urning off the computer These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Shut down if you want the computer to shut down when you close the display panel.
90 Getting Started T urning off the computer 2 Click Hibernate in the pop-up menu . The computer sav es the state of all open progr ams and f iles, turns of f the display , and then turns of f. Configuring Hibernation mode options Y ou can place the computer into Hibernation mode b y either pressing the power b utton or closing the display panel.
91 Getting Started T urning off the computer 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 5 Select Hibernate for the options you want.
92 Getting Started T urning off the computer Starting again from Hibernation mode T o start up the computer from Hibernation mode, press the power button until the ON/OFF light gl o ws green.
93 Getting Started T urning off the computer T o use any of these methods, you f irst need to enable them using the Power Options feature. 1 Click Start , Contro l Panel , System and Security , and then Po wer Options . The Po wer Options window appears.
94 Getting Started T urning off the computer 5 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options screen 6 Select Sleep for the options you want.
95 Getting Started Customizing your computer’ s settings Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the ON/OFF light glo ws green.
96 Getting Started Caring for your computer Moving the computer Before moving your computer, e ven across the room, make sure all dri ve acti vity has ended (the intern al storage driv e and optical disc dri ve indicator lights stop glowing) and all e xternal perip heral cables are disconnected.
97 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive.
98 Learning the Basics Using the ke yboar d ❖ Back up your files to ex ternal media on a regular basis. Label the backup copies clearly and store them in a safe place.
99 Learning the Basics Using the ke yboar d Character keys T y ping with the character keys is very mu ch li ke t yp in g o n a typewriter , e xcept that: ❖ The space bar creates a space char acter instead of just passing ov er an area of the page. ❖ The lo wercase letter l (el) and the number 1 are not interchangeable.
100 Learning the Basics Using the ke yboar d F1 through F12 are called function keys because the y ex ecute programmed functions when pressed. Used in combin ation with the Fn key , fun ction keys marked with icons ex ecute specific functions on the computer .
101 Learning the Basics Starting a pr ogr am Using the overlay to type numeric data The keys with the numbers on th eir right front are the numeric ov erlay keys. T o turn the numeric ov erlay on, press Fn and F11 simultaneously . The numeric overlay light glo ws wh en the numeric overlay is on.
102 Learning the Basics Starting a pr ogram If you pause with your mouse on All Programs, it will open it up . Y ou may need to scroll up or down to see the complete list. 2 Click the program group, in this example, Acces sories . The Accessories menu is displayed.
103 Learning the Basics Saving your work 7 In the right part of the window , double-click wordpad . The operating sy stem opens W ordPad. T o close the program, click the Clo se button in the upper-right corner of the program’ s window .
104 Learning the Basics Saving your work Saving files 1 Click on the arrow in the upper -left corner of your W indows ® -based application to display the drop-down menu, and then click Sav e . If you are working with a docum ent that already has a f ile name, this i s all you need to do.
105 Learning the Basics Printing your work Microsoft ® W ord file. Creating your own extension is usually unwise, since the program is unlikely to recognize a strange extension and may refuse to handle your file correctly . TECHNICAL NOTE: By default, the Windows ® operating system does not show file extensions.
106 Learning the Basics Backing up your work 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer . Y ou can back up your files to diff erent types of media such as CDs, D VDs, external stor age media, or to a network, if av ailable.
107 Learning the Basics Using the optical disc drive TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to over write a file that already exists on the internal storage drive. Make sure the backup v ersion is the one you want before overwriting the existing file.
108 Learning the Basics Using the optical disc drive Drive in-use indicator light —Indicates when the driv e is in use. Eject button —Press to release the disc tray . Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing.
109 Learning the Basics Using the optical disc drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for optical discs” on page 112 .
110 Learning the Basics Using the optical disc drive If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance. 9 Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
111 Learning the Basics Using the optical disc drive For more information regarding supported optical media formats please refer to your computer’ s detailed specif ications at pcsupport.toshiba.com . Due to manufacturing and quality variations in third party optical media (e.
112 Learning the Basics T oshiba’ s online r esour ces Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray out until it is fully open , remove the disc, and place it in its protecti ve co ver .
113 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your com puter while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process.
114 Mobile Computing Running the computer on battery power Y our computer contai ns T oshiba EasyGuard ® . The T oshiba EasyGuard * technology is made up of four fou ndational elements that incorpora.
115 Mobile Computing Running the computer on battery power T o ensure that the battery maintain s its maximum capacity , operate the computer on battery po wer at least once a month. The Lithium-Ion battery has no memory effect so it is not necessary to let the battery fully dischar ge each time.
116 Mobile Computing Char gi ng batteries Using additional batteries If you travel and need to work for man y hours with out an A C power source, you may purchase a battery m odule for use in the com puter , or carry additional charged battery packs with you.
117 Mobile Computing Char ging ba tteries The battery may not start ch arging immediately under the following conditions: ❖ The battery is extremely hot or cold. T o ensure that the battery char ges to its full capacity , wait until it reaches room temperature (50 to 80 degrees F ahrenheit, 10 to 26 degrees Celsius).
118 Mobile Computing Monitoring main battery power It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low , the real-time clock and calendar may display the incorrect time and date or stop working.
119 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ), the ON/OFF light ( ). When the ON/OFF light flashes amber , it indicates that the system is suspended (using the Windows ® operating system Sleep command).
120 Mobile Computing Monitoring main battery power Mov e the pointer ov er the po wer icon in the notification area, see “Finding your way around the desktop” on page 133 for more information on the notification area. A pop-up message displays the remaining battery power as a percentage.
121 Mobile Computing Monitoring main battery power T o change the default notification settings: 1 Click Start , Contro l Panel , System and Security , and then Po wer Options . The Po wer Options window appears. 2 Click Change plan s ettings under the po wer plan to be customized.
122 Mobile Computing Monitoring main battery power There are v arious ways in which you can conserv e power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves .
123 Mobile Computing Monitoring main battery power T o edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change plan settin gs to choose the plan you want to edit.
124 Mobile Computing Using the T OSHIB A eco power plan Using the TOSHIBA eco power plan This computer is equipped w ith the TOSHIB A eco power plan. Operating the computer with th is po wer plan enabled reduces electrical power consumption by slightly lo wering system performance.
125 Mobile Computing Changing the main battery Changing the main batter y When your main battery has ru n out of power , you have two options: plug in the A C adaptor or install a char ged main battery .
126 Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlo cked position. (Sample Illustration) Unlocking the battery r elease lock 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer .
127 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks.
128 Mobile Computing T aking car e of your battery 4 T urn the computer right side up. 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 125 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life.
129 Mobile Computing Disposing of used batteries Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
130 Mobile Computing Disposing of used b atteries Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating apparatus (e.g., microwave oven). Heat can ca use a battery pack to explode and/or release caustic liquid, both which may possibly cause serious injury .
131 Mobile Computing T raveling tips T raveling tips The en vironmental precautions listed in “Selecting a place to work” on page 42 , also apply while traveling. ❖ Nev er leav e your computer on a sunny ledge or in a place where it could get wet or covered in dust.
132 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system.
133 Exploring Y our Computer’ s Features Exploring the desktop Finding your way around the desktop Y our computer’ s desktop includes several standard features: icons, Start button, taskbar , notification area, and background pattern.
134 Exploring Y our Computer’ s Features Explorin g the desktop ❖ TECHNICAL NOTE: If you delete a large number of files or very large files from the internal storage drive, there may be insufficient space available in the Re cycle Bin to hold these files.
135 Exploring Y our Computer’ s Features Setting up for communications T askbar Each time you open a program, a button associated with that program appears on the taskbar . With some programs, a b utton appears on the taskbar for each document or window you open.
136 Exploring Y our Computer’ s Features Setting up for communications For information on ho w to set up a wireless connection, refer to your wireless networking device documentation or your network administrator . T o enable or disable wireless communication, use the Hot Key Fn + F8 .
137 Exploring Y our Computer’ s Features Setting up for communications Connecting a modem to a telephone line (A vailable on certain models.) Y our computer may come with a built-in modem th at can be connected to a standard voice-grade telephone line.
138 Exploring Y our Computer’ s Features Explor ing audio feat ur es Exploring audio features Y ou can use your computer to record sounds using the com puter’ s internal microphone (av ailable on certain models) or an opti onal external microphone.
139 Exploring Y our Computer’ s Features Using the W eb Camera TECHNICAL NOTE: When using amplified speakers, use speak ers that require an external power source.
140 Exploring Y our Computer’ s Features Using an Expr essCard ® Using an ExpressCard ® (A vailable on certain models.) The ExpressCard ® slot supports the use of ExpressCard media. The slot also supports ho t swapping, which allo ws you to replace one ExpressCard with another while the computer is on.
141 Exploring Y our Computer’ s Features Using the Memory car d r eader 4 Press the ExpressCard eject butto n once to pop it out slightly , and push it in to remove the ExpressCard. The ExpressCard ejects sl ightly from the slot. 5 Grasp the edges of the ExpressCar d and slide it out of the slot.
142 Exploring Y our Computer’ s Features Using the Memory car d r eader 2 Push the media i nto the adapter u ntil it locks in place (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts. Y ou could expose the storage area to static electri city , which can destroy data.
143 Exploring Y our Computer’ s Features Using the eSA T A/USB combo port Using the eSA T A/USB combo port (A vailable on certain models.) Y our computer includ es an eSA T A/USB combo port, which can be used with both eSA T A (external Serial Advanced T echnology Attachment) de vices and USB devices.
144 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help yo u to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns.
145 Utilities TOSHIB A Assist ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ TOSHIB A Accessibility ❖ Fingerprint Authentication Utilit y ❖ TOSHIB A eco Utility™ ❖ TOSHIB A Ser.
146 Utilities TOSHIB A Assist Connect The feature a vailable in this category is: ❖ Bluetooth ® Settings (Sample Image) T OSHIBA Assist window – Connect tab.
147 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password ❖ TOSHIB A Security Assist (Sample Image) T OSHIBA Assist window – Secu.
148 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility ❖ TOSHIB A HDD Protection Utility (Sample Image) T OSHIBA Assis.
149 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Se tup (Hardware Settings) ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Butto.
150 Utilities TOSHIB A Application Installer TOSHIBA Application Installer The T OSHIB A Application In staller allo ws you to re install the dri vers and applications that were originally bundled with your computer .
151 Utilities Setting passwor ds Setting passwords Setting a password lets you walk aw ay from your computer whi le providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again.
152 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to se.
153 Utilities Setting passwor ds 6 Click Set . 7 Click OK if you want to save the password to a text file or external media of your choice, or click Cancel to continue without saving the password to a text f ile. 8 Shut down the system to complete the process.
154 Utilities Setting passwor ds 2 On the left side, click the Secure tab . 3 Click the User Password icon. The TOSHIB A P assword Utility windo w appears. (Sample Image) TOSHIB A P asswor d Utility window 4 Click Set . 5 Enter your pas sword, and then enter it ag ain to verify .
155 Utilities TOSHIB A F ace Recognition Utility TOSHIBA Face Recognition Utility Y our computer may come with the TOSHIB A Face Recognition utility . This utility provides another way to log on to y our computer . For high security purposes, TOSHIBA Face Re cognition is not a suitable substitute for Windows ® passwords.
156 Utilities TOSHIB A Security Assist TOSHIBA Security Assist The TOSHIB A Security Assist Ut ility acts as a “command center” where you can set up v arious passwords or other security features, and see ho w these features can be used with each other to increase security ev en further , or to simplify the ways that you protect your system.
157 Utilities TOSHIB A Security Assist ❖ Log on Settings —Select this category to set up security options that protect in di vidual user accounts. ❖ Password of current user : Check the status of the W indows ® password for the account to which you are currently logged on.
158 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have.
159 Utilities TOSHIB A HDD Pr otection Utility TOSHIBA HDD Protection Utility The TOSHIB A HDD Protection Utility controls your computer’ s hard disk dri ve (HDD) protection feature, which parks the HDD whene ver motion is detected on the computer .
160 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contro l Panel , Hardware and Sound , and then under Devices and Printers , click Mouse , or click the Mouse icon in the Op timize tab of TOSHIB A Assist .
161 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the TOSHIB A configuration management tool av ailable through th e W indows ® operating system.
162 Utilities TO S H I B A H a rd w a re S e t u p ❖ CPU —Allows you to enable or disable CPU frequency switching modes Dynamically Swit chable —This mode is th e default setting for your comput.
163 Utilities USB Sleep and Char ge Utility USB Sleep and Charge Utility This utility displays w hether the “USB Sleep and Charge function” is enabled or disabled and shows the position of the USB port that supports the “USB Sleep and Charge function.
164 Utilities USB Sleep and Char ge Utility ❖ When “USB Sleep and Charge function” is set to Enabled, USB bus power (DC 5V) will be supplied to the compatible port even when the power of the computer is turned OFF . USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports.
165 Utilities USB Sleep and Char ge Utility Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag.
166 Utilities USB Sleep and Char ge Utility Power supply mode settings Y our computer may provide two dif ferent charging modes, to support various types of USB de vices. If your computer provides more than one charging mode, the char ging mode you shoul d select depends on the USB d evice you want to charge.
167 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 221 ).
168 Utilities TOSHIB A Button Support TOSHIBA Button Support TOSHIB A Button Support allows you to customize the system control panel buttons. These butt ons are located on the system control panel near th e upper-right corner of the keyboard.
169 Utilities TOSHI BA A ccessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required.
170 Utilities F ing erprint Authenticati on Utility Fingerprint Authentication Utility (A vailable on certain models.) The fingerprint authentication uti lity can be used to replace the keyboard-based user password authentication system when booting up.
171 Utilities F ing erprint Authent ication Utility Fingerprint Logon The fingerprint utility enables logon to your comp uter using fingerprints. During user enrollmen t, fing erprint samples are sa ved and associated with the user’ s W indows ® user account.
172 Utilities F ing erprint Authenticati on Utility ❖ A void the follo wing finger conditions for enrollment or recognition as they may result in fingerprint enrollment erro rs or a drop in the f ingerprint recognitio n success rate. ❖ Soaked or swollen fi nger (e.
173 Utilities F ing erprint Authent ication Utility Fingerprint reader limitations ❖ The fingerprint reader compar es and analyzes the unique characteristics in a fingerprint. Ho wev er , there may be instances where certain users are unable to register their fingerprints due to insuf ficient unique characteristics in their fi ngerprints.
174 Utilities TOSHIB A eco Utility™ TOSHIBA eco Utility™ The TOSHIB A eco Utility™ monitors your power sa vings from using the eco power plan by tracking real-time power consumption and accumulated savings o ver time.
175 Utilities TOSHIB A Service Station TOSHIBA Service Station The TOSHIB A Service Station helps you keep your ne w computer running at its best by notifying you when updated software, firmw are, documentation or othe r information is av ailable for your computer .
176 Utilities TOSHIB A PC Health Monitor Y ou may disable the T OSHIB A PC Health Monitor at any time by uninstalling the software via t he W indows ® Control P anel. Doing so will automatically delete all collected inform ation from the internal storage dri ve.
177 Chapter 6 If Somet hing G oes W r ong Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself.
178 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask .
179 If Something Goes Wrong Pr oblems when you turn on the computer The computer displays the WARNING RESUME F AILURE/Windows Error Recovery – Windows did not shut down successfully message. T o continue, select Start W indows normally . This can happen if the computer was put into Sl eep mode and the battery has discharged.
180 If Something Goes Wrong The W indo ws ® operating system is not working If the trickle-charging does not prov e ef fectiv e, visit the T oshiba W eb site at pcsupport.tosh iba.com and see the Support Bulletin Step-Charging the computer’ s battery (click the Ask Iris ® link and search for the s upport b ulletin by name).
181 If Something Goes Wrong The W indo ws ® operating system is not working ❖ The operating system responds dif ferently from the norm al routine. ❖ The screen does not look right. Unless a hardware de vice has failed, probl ems usually occur when you change the system in some way such as installing a ne w program or adding a device.
182 If Something Goes Wrong The W indo ws ® operating system is not working If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is v ery slow . Many f actors contribute to the speed with which you can surf the Internet.
183 If Something Goes Wrong F ixing a pr oblem with Device Manag er Fixing a problem with Device Manager Device Manager pro vides a way to check and change the configuration of a de vice. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable.
184 If Something Goes Wrong Memory pr oblems Memory problems Incorrectly connected or faulty memory modu les may cause errors that seem to be hardware or ev en software related. It is worthwhile checking for these firs t: 1 Click Start , and then click the Shut do wn button in the lo wer-right corner of the Start menu.
185 If Something Goes Wrong P ower and the batteries If the A C po wer light stil l does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance. The A C adaptor and power cord/c able work corr ectly , b ut the battery will not charge.
186 If Something Goes Wrong K e yboar d pr oblems Keyboard problems If, when you type, strange things happen or nothin g happens, the problem may be related to the keyboard itself. The keyboard pr oduces unexpected characters. A keypad o verlay may be on.
187 If Something Goes Wrong Display pr oblems If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’ s po wer cord/cable is f irmly plugged into a working p ower outlet. ❖ Check that the cable connecting the external monitor to th e computer is fi rmly attached.
188 If Something Goes Wrong Disk or storag e drive pr oblems Small bright dots appear on y o ur TFT display when yo u turn on y our compu ter . Small bright dot s may appear on your screen display when you turn on your computer .
189 If Something Goes Wrong Optical disc drive pr oblems 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system er rors ❖ Scan for and attempt reco very of bad sectors 7 Click Start . Error- checking tests and repairs the storage driv e.
190 If Something Goes Wrong Sound system pr oblems Y ou press the disc eject b utton, but the dri ve tray does not slide out. Make sure the computer is connect ed to a po wer source and turned on. The optical disc dri ve eject mechanism req uires po wer to operate.
191 If Something Goes Wrong Expr essCar d ® pr oblems The computer emits a loud , high-pitched noise. This is feedback between the mi crophone and the speakers. It occurs in any sound system when inpu t from a micropho ne is fed to the speakers and the speak er volume is too loud.
192 If Something Goes Wrong Expr essCar d ® pr oblems 2 Double-click the appr opriate ExpressCard, which w ill be listed under one of the categories show n, for e xample: Disk dri ves, Network adapters, Other , etc.
193 If Something Goes Wrong Printer pr oblems 2 Click Eject [device name] for the de vice you want to remove. The Safe T o Remove Hardware message appears. 3 Remov e the device. Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported.
194 If Something Goes Wrong Modem pr oblems Y ou may ha ve connected the printer while the computer is on. Disable Sleep mode, turn of f the computer, and turn off the printer . T urn the printer back on, make sure it is online, and then turn the computer back on.
195 If Something Goes Wrong W ireless networking pr oblems Wireless networking problems This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi ® ) networking. The terms and concepts used assume a bas ic understanding of networks, and may be for more advanced users.
196 If Something Goes Wrong D VD operating pr ob lems ❖ Use IPCONFIG to verify that the computer has a useful IP address - one other than the priv ate address of 169.254.xxx.xxx assi gned by W indo ws ® . 1 Click Start to open the Start menu. 2 T y pe Cmd in the Search programs and files f ield.
197 If Something Goes Wrong D VD operating pr oblems 3 Use the D VD player so ftware that came with your comp uter to view D VD movies. 4 Clean the disc and try again. A dirty dri ve can also cause audio problems. If you have tried se veral discs and all fail, consider sending your drive to an authorized service provid er to get it cleaned.
198 If Something Goes Wrong Develop good computing habits Develop good computing habits Sa ve y our work fr equently . Y ou can ne ver predict when your co mputer will lock, forcin g you to close a program and lose unsaved changes. Man y software programs build in an automatic backup, but you should not rely solely on this feature.
199 If Something Goes Wrong Develop good computing habits Data and system configuration backup in the Windows ® operating system The W indo ws ® operating system offers some easy-to-use features for backing up your W indows ® settings and your data - documents and other important files.
200 If Something Goes Wrong Develop good computing habits Then, at a later time, you can re-establish your Windo ws ® configuration using the sa ved restore point. T o do th is: 1 Click Start , All Programs , Acces sories , System T ools , and then System Restore .
201 If Something Goes Wrong Develop good computing habits Follo w these steps to back up y our computer or files to optical discs, or a storage driv e: Y ou cannot back up the computer while running on battery power . Connect the AC adaptor before continuing.
202 If Something Goes Wrong Develop good computing habits ❖ Restart the W indo ws ® operating system. Alw ays restart th e W indows ® operating system after each installation, ev en if the installation utility does not prompt you to do so.
203 If Something Goes Wrong If you need further assistance ❖ The USB Sleep and Charge function may not work with certain external de vices ev en if they are compliant with the USB specification. In those cas es, powe r on the computer to charge the device or use a dif ferent charging de vice.
204 If Something Goes Wrong If you need further assistance ❖ If the problem occurs while you are running a program, consult the program’ s documentation for troubleshooting suggestio ns. Contact the software company’ s technical support group for their assistance.
205 If Something Goes Wrong Other T oshiba Internet W eb sites Other T oshiba Internet Web sites T oshiba’ s worldwide offices toshiba.com W orldwide T oshiba corporate site laptops.toshiba.com Marketing and product information in the USA accessories.
206 If Something Goes Wrong T oshiba’ s worldwide off ices For more information on additio nal T osh iba worldwide locations, please visit: www .t oshiba.co.jp/index.htm . Latin America and Caribbean T o shiba America Information Systems 9740 Irvine Blvd.
207 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards provi de a quick way to modify selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot Ke y Cards and Application Cards.
208 Hot Keys/TOSHIBA Cards Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off.
209 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 145 .
210 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Applicati on Cards: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stack ed” card on the far right of the display .
211 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected wh en the Application Cards are displayed.
212 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a us er with a valid account will need to log back on to gain access to the computer .
213 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window .
214 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mode” on page 92 .
215 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 89 .
216 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the p o w e r - o n di s pl a y op t i o n s (only the.
217 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all m odels. Some systems also support an additional Swap Image Display mode.
218 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the W i-Fi ® module.
219 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad™. For more information on using the T ou chPad, see “Using the T o uchPad™” on page 76 .
220 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Cursor control overlay Numeric overlay or Fn + This TOSHIB A Card or hot ke y turns the cursor control ov erlay on and off.
221 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) Keyboard hot key functions or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution.
222 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer ships w ith the correct power su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world.
223 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide.
224 Glossary DIMM Dual Inline Memo ry Module DOS Disk Operating System DPI Dots Per Inch DV D Digital V ersatile (or V ideo) Disc DV D - R O M Dig ital V ersatile (or V ideo) Disc Read-Only Memory EPR.
Glossary 225 RO M Read-Only M emory RT C Real-T ime Clock SD Secure Digital SDRAM Synchronous Dynamic Random Access Memory SSD Solid State Driv e TFT Thin Film Tr ansistor USB Univ ersal Serial Bus URL Uniform Resource Locator WA N W ide Area Network www W orld W ide W eb Te r m s The following terms may appear in this user’ s guide.
226 Glossary B backup —A copy of a f ile, usually on a remov able disk, kept in case the original file is lost or damaged. Basic Input/Output System (BIOS) —See BIOS. baud rate —The speed at which a communication de vice, such as a printer or mo dem, transmits in formation.
Glossary 227 C cache —A section of very fast memory in which frequently used information is duplicated for qu ick access. Accessing data from cache is faster than accessing it from the computer’ s main memory . See also CPU ca che, L1 c ache, L2 cach e.
228 Glossary CPU cache —A section of very fast memory residing between the CPU and the computer’ s main memory that temporarily stores data and instructions the CPU will need to ex ecute commands and programs. See also cach e, L 1 ca che, L2 c ache.
Glossary 229 document —Any file created with an appl ication an d, if saved to disk, gi ven a name by which it can be retrie ved. See also fil e . double-click —T o press and release the point ing device’ s primary button rapidly twice without moving the pointi ng device.
230 Glossary F fil e —A collection of related in formation, saved on disk with a uniqu e name. A file may be a program, information used by a program, or a document. See also docum ent. File Allocation T able (F A T) —The section of a s t o r a ge d r ive that keeps track of the location of stored files.
Glossary 231 H DM I ( High-Definition Multimedia Interface) —A n interface used to transmit high quality audio and video signal via a single cable in digital format, providing better picture quality than analog signal.
232 Glossary LAN (Local Area Network) —A group of com puters or other devices dispersed ov er a relati vely limited area and connected by a communications link that enables any de vice to interact with an y other on the network.
Glossary 233 motherboard —The computer’ s main circuit board that contains the processor , memory , and other primary com ponents. MS-DOS pr ompt —See system pr ompt. multi-function drive —A D VD dri ve that can r ead and write to CD and DV D m e d i a .
234 Glossary password —A unique string of characters en tered by a user to verify his or her identity to the computer or the network. PC Card —A credit-card-sized expansion card designed to increase the capabilities of computers.
Glossary 235 Random Access Memory —See RAM. Read-Only Memory —See RO M . reb o ot —See boot , re s t a r t . removable disk —A disk that can be remov ed from a disk dri ve.
236 Glossary shortcut —See k eyboar d shortcut . Sleep —A feature o f some W indo ws ® operating systems that allows you to turn off the computer without exiting your open applications and to continue from where you left of f when you turn the computer on again.
Glossary 237 W We b —See W o rld W ide W eb . Wi- F i ® —A registered trademark term of the W i-Fi Alliance that stands for W ireless Fidelity , and is anot her term for the communication protocol to permit an Ethernet connect ion using wireless communication components.
238 Index A A C adaptor 46 AC p o w e r 115 A C power light 46 accessing network 136 adding memory check total memor y 60 memory (optional) 51 optional external devices 51 adequate ventilation cooling.
239 Index running computer on battery power 114 safety precautions 128 setting notifications 120 battery indicator light 119 BIOS Setup see TOSHIB A Hardware Setup but t on eco Utility™ 124 eject, o.
240 Index ext e rn a l 80 display output settings 82 display panel opening 49 display , external adjusting 83 disposal information 28 disposing of used batteries 129 DV D caring for discs 112 removing.
241 Index disabling or enabling wireless devices 218 display brightness 217 Hibernatio n mode 215 keyboard o verlays 221 Lock (Instant security) 212 Output (Display sw itch) 216 po wer plan 213 Sleep .
242 Index remo ving memory media 14 2 using 141 memory module installation 52 inserting into socket 55 removing 57 , 59 microphone using 138 modem connecting to telephone line 137 problem solving 194 .
243 Index connecting cable to A C adaptor 47 cord/cable 47 cord/cable connectors 222 energy-sa ving features 113 turning on 50 power b utton 50 po wer management 115 optimum performance 115 po wer pla.
244 Index a place to work 42 power plan options 122 video cables 81 setting lo w battery notifications 120 setting up A C adaptor 46 adding memory (optional) 51 communications 135 computer 45 software.
245 Index T oshiba Ea syGuard® 114 TOSHIB A eco po wer plan 124 TOSHIB A eco Utili ty™ 174 TOSHIB A Face Recognition Utility 155 TOSHIB A Hardware S etup 161 TOSHIB A HDD Pr otection Util ity 159 T.
246 Index computer more quickly 87 options 85 turning on power 50 U USB Sleep and Charge cannot use 202 USB Sleep and Charge Utility 163 USB W akeup function does not work 203 USB-compatible printer 8.
デバイスToshiba PT311U04E07Kの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba PT311U04E07Kをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba PT311U04E07Kの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba PT311U04E07Kの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba PT311U04E07Kで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba PT311U04E07Kを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba PT311U04E07Kの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba PT311U04E07Kに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba PT311U04E07Kデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
