ToshibaメーカーSD-37VBSBの使用説明書/サービス説明書
ページ先へ移動 of 60
DVD PLAYER Hi-Fi VIDEO CASSETTE RECORDER USER’S GUIDE SD-37VBSB DIGITAL VIDEO 2J50101A [EN]Cover 27/2/06, 5:38 PM 1.
2 W ARNING: T O REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NO T EXPOSE THIS APPLIANCE T O RAIN OR MOISTURE. DANGEROUS HIGH V OL T A GES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET . REFER SER VICING TO QU ALIFIED PERSONNEL ONL Y . CA UTION: This Digital Video Disc Play er employs a Laser System.
3 SAFETY PRECA UTIONS SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
4 Precautions Notes on handling When shipping the D VD/VCR, the original shipping car ton and packing materials come in handy . For fully protection, repack the unit as it was originally packed at the factory . Do not use volatile liquids , such as insect spray , near the DVD/VCR.
5 Notes on discs On handling discs Do not touch the playback side of the disc. Do not attach paper or tape to discs. On cleaning discs Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the centre outwards with a soft cloth.
6 DIGITAL VIDEO About this owner’ s manual This owner’ s manual e xplains the basic instr uctions of this DVD/VCR. Some DVD video discs are produced in a manner that allows specific or limited operation during playbac k. As such, the D VD/VCR may not respond to all operating commands.
7 Contents SAFETY PRECAUTIONS ................................ 2 Precautions ...................................................... 4 Notes on discs .................................................. 5 Contents ........................................
8 SCART -sock et (for VCR/DECODER) (L2) Parts and functions Front Rear AC mains read COAXIAL DIGIT AL A UDIO OUT jack RF IN jack A UDIO (L/R) OUT jacks RF OUT jack SCAR T -socket (f or RGB OUT , Compo.
9 No . Display VCR mode of TV/VCR switch Display VCR DV D CD 10 : 00 01 : 00 2 L1/L2/L3 TRK CH 2 Playbac k (lights) / Auto resume (flashes) Still picture D VD disc is inser ted.
10 OPEN/CLOSE Open or Close the tra y 33,34,54 PO WER Po w er on/off 16 TV/VCR Switch to TV only at Scar t connection 26 VCR Select to operate VCR 16 DV D Select to operate D VD 33 CLOCK/COUNTER Chang.
11 Remote control 1 23 Replace the compar tment cov er. Install two "R03/AAA" batteries (supplied), paying attention to the polarity diagram in the batter y compar tment. Open the battery compart- ment cover in the direction of the arrow . How to install the batteries Use micro batteries type UM-4 ( R03/AAA-Size ).
12 Basic connection Connect your DVD/VCR to your home's aerial and to your TV-set as shown in the illustration. When you have finished these connections then connect your DVD/VCR to the 230 V / 50 Hz mains. In addition to the coaxial cable connection, you should also connect the supplied SCART cable from the DVD/VCR to your TV as shown.
13 SCART-cable (not supplied) If a Satellite Receiver is used, we recommend the following configuration: Connection to a Satellite Receiver Playback connection The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the model and features of each component.
14 Connect to an A V Amplifier with built-in digital surround If you are using an Amplifier with a built-in digital surround as f ollows, y ou can enjoy the v ar ious audio systems such as Dolby Digital and DTS by using the Coaxial Digital Output.
15 Plug your D VD/VCR's plug into the mains supply . "Auto" will star t to flash in the display . Y our D VD/VCR will auto- matically tune itself in and set the correct time and date (This may tak e approx.
16 Setting the on-screen language 3 1 2 4 Turn on your TV and select the AV input mode. So you can follow the setting on TV screen. Notes: • If the unit does not operate properl y , or No key operation (b y the unit and/ or the remote control): Static elec- tricity , etc.
17 4 Setting the time and date manually 2 3 1 5 7 8 VCR Preparation: • Tu rn ON the TV and set to the A V input mode. • Press VCR to select the VCR mode. (The VCR indicator will light.) Example: Setting the clock to "11:30" October , 28 (SA T), 2006.
18 The Auto setup function (see page 15) memorizes all broadcasts to the suit- able CH positions. However some broadcast may not be memorized due to weak signal. In this case, use manual tuning function. T uning the TV stations manuall y Note: Occasionally, the auto search might catch a weak signal and stop.
19 VCR VCR VCR Loading and unloading a cassette tape Erase prevention tab Screwdriver Adhesive tape Erase prevention tab 12 Use only video cassette tapes marked . Loading Push the center of the tape until it is automatically inserted. Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left.
20 To rewind the tape or forward it rapidly To stop pla yback 1 2 Notes: • This VCR selects the playbac k tape speed SP or LP automatically . • The Cassette tape and D VD disc can be play ed back simultaneously . If you press VCR or DV D , the tape playback and D VD pla yback alter nate with each other on the screen.
21 Special playback VCR VCR VCR Picture Search Reverse picture search function Press REV x 1 or x 2 during the playback. Forward picture search function Press FWD x 1 or x 2 during the playback. To return to playback: Press PLAY . Still Picture Press PAUSE/STEP during playback.
22 1 4 3 2 Repeat playback Note: If the unit is turned off or star ts recording, the repeat mode is cancelled. Normal repeat playback The entire video tape will be play ed until its end. The tape will then automatically rewind to the beginning and the playback will be re- peated.
23 VCR VCR VCR Counter Display 2 1 3 12:00 SUN 00:04:38 SP 12:00 SUN 00:00:00 SP ZERO RETURN function This function makes tape-rewinding stop at the counter 00:00:00 position automatically . Notes: • When you load a video cassette, the display indication changes to "00:00".
24 2 1 2 1 REC VCR REC VCR INDEX NO. (up to 9) or is displayed Whenever a recording is begun an invisible index mark is recorded on the tape. These index marks are all identical, and each mark means: "Here starts a new recording".
25 REC VCR VCR REC VCR Recording a TV Program 4 1 2 3 VCR VCR Notes: • Since the DVD/VCR has a built-in TV tuner the TV set may be turned off when recording. The TV set may only be used to check for accurate program adjust- ments or to monitor recordings.
26 VCR Recording a TV Progr am 1 2 3 “VCR” indicator goes on. “VCR” indicator goes off. “VCR” indicator goes on. You can record a program using the TV receiver of the DVD/VCR and at the same time watch another program on the TV set using its receiver.
27 One-touch Timer Recor ding (O TR) 3 4 “REC” will keep blinking in the display. VCR 1 2 VCR REC VCR The one-touch timer recording feature provides a simple and convenient way to make a timed recording.
28 2 4 1 3 --:-- --:-- ------ -- --:-- --:-- -- ------ --:-- --:-- -- ------ --:-- --:-- -- ------ --:-- --:-- ------ -- --:-- --:-- ------ -- --:-- --:-- ------ -- --:-- --:-- ------ -- / ENTER SELECT : EXIT : MENU - - - - - - - - .
29 Timer recording 5 --:-- --:-- ------ -- 13:00 14:30 1 23 MON --:-- --:-- ------ -- --:-- --:-- ------ -- --:-- --:-- ------ -- --:-- --:-- ------ -- ------ --:-- --:-- -- ------ --:-- --:-- -- - - .
30 NICAM OFF NICAM M1/2 NICAM M1 NICAM ST 1 Stereo recor ding and playbac k This D VD/VCR is capable of recording sound in Hi-Fi system. The recording will be performed automatically . NICAM STEREO broadcasts are recorded in its original sound system regardless of the setting.
31 Stereo recording and playback Playback Use AUDIO SELECT to select under stereo/mono or bilingual playback. See the table below for more information.
32 5 1 2 3 4 VCR Press AUX on the recording unit repeatedly until L3 appears. OR Playback on camera Playback unit (not supplied) Recording unit (not supplied) 1 2 3 Duplicating a video tape When you try to connect with a cable, make sure the power of both units have been turned off.
33 Pla ying a disc Press OPEN/CLOSE or PLA Y on the unit. The disc tra y closes automatically . On the TV -screen, “ ” changes to “Reading” and then playback commences. Press / or / to select title. Press ENTER. • Title is selected and play commences.
34 To pause pla yback (still mode) Press PA USE/STEP dur ing playbac k. To resume normal playbac k, press PLA Y . • The sound is muted during still mode. To stop pla yback Press STOP . To remove the disc Press OPEN/CLOSE . Remove the disc after the disc tray opens completely .
35 Y ou can pla y discs at various speeds. Playing in fast reverse or fast forward directions Playing frame by frame Press REV or FWD during playback. REV : Fast reverse playback FWD : Fast forward playback Each time you press REV or FWD , the playback speed changes.
36 Zooming This unit will allow you to zoom in on the frame image. Y ou can then make selections b y switching the position of the frame. 1 2 Press ZOOM during playback. The center part of the image will be zoomed in. Each press of ZOOM will change the ZOOM 1 (x 1.
37 Marking the scenes Returning to the scenes 1 Press MARKER during playback or stop mode. 2 1 3 Marking desired scenes 2 3 Notes: • Some discs may not work with the marking operation. • The marking is canceled when you open the disc tray or turn the power off .
38 Repeat playback 1 Press PLAY MODE during playback or stop mode. Repeat playback/A-B Repeat playback Press PLAY MODE again to clear the screen. 3 A-B Repeat playback A-B repeat playback allows you to repeat selection between two selected points. 1 Press A-B RPT during playback.
39 Press PLAY MODE during stop mode. 1 Press B B B B B / A A A A A to return to the left column, then press C C C C C / D D D D D to select the “Program Playback” and press ENTER. The programs you selected will start to playback in order. • To resume normal playback, select Mode “Off” in step 2.
40 Press C C C C C / D D D D D / B B B B B / A A A A A to select the desired title. Changing angles/Title selection/D VD menu Press ANGLE during playback.
41 Changing soundtrack language Y ou can select the language when y ou play a multilingual disc. 1 2 Press AUDIO during playback. The current soundtrack language will appear.
42 Subtitles/T o turn off the PBC/Disc status To turn off the subtitle, press SUBTITLE until “Off” appears. • The on screen display will disappear after a few seconds. 1 Notes: • Depending on the DVD, you may not be able to change subtitles, or to turn subtitles on or off.
43 MP3/JPEG/DivX ® and A udio CD operation Limitations on MP3/JPEG/DivX ® CD playback • MP3/JPEG/DivX ® CD is the disc that is standardized by ISO9660, its file name must include 3-digits extension letters, “.mp3”, “.jpg”, “.div”, “.
44 Press / to select file. • In case the current directory includes more than 8 files, press or to scroll in the file list. • To see contents in folder, select the folder and then press ENTER . To return to the upstairs directory, select “ Go Up .
45 Place a disc on which JPEG files have been recorded onto the tray. 1 A file browser screen will appear on the screen. 2 Press C / D to select the file. To display a thumbnail list, press DVD MENU . Press B / A or C / D to select the desired file. (To return to a file browser, press TOP MENU .
46 Place a disc on which DivX ® files have been recorded onto the tray. 1 A file browser screen will appear on the screen. 2 Press C / D to select file. 3 Press ENTER or PLAY. The selected DivX ® movie will be played back on the screen. Press STOP to end playback.
47 Folder-1 Folder-2 MP3-1 MP3-2 MP3-3 Select Files Repeat :Off Mode :Off Folder-1 Folder-2 MP3-1 MP3-2 MP3 3 Select Files Repeat :Track Mode :Off Repeat and program playback using file browser Repeat playback (CD) In the file browser, press B / A or C / D to select “Repeat” during stop mode.
48 In the file browser, press B / A or C / D to select “Edit Mode”, then press ENTER. When “Edit Mode” is black color, you can mark the files which you want to add into Program list. Press B / A or C / D to select the file you want to add into the program list.
49 Press SETUP during stop mode. The following on-screen display appears. 1 2 3 To c lear SETUP screen, press SETUP or RETURN. 6 Customizing the function settings Press C or D to select the desired section, then press B or A . First option will be highlighted.
50 Setting details Menu, Subtitle, Audio You can select the language of “Menu”, “Subtitle” and “Audio” if more than one languages are recorded onto the disc. English, Francais, Espanol, Deutsch, Italiano: The selected language will be heard or seen.
51 JPEG Interval You can continuously playback all JPEG files automatically. After the selection below, the disc will start playback on which JPEG files have been recorded. Off: Pla ys back one file at a time. 5 Seconds: Pla ys back images in the form of a slide show at 5 second intervals.
52 Parental control setting Some discs are specified is not suitable for children. Such discs can be limited not to playback with the unit. 1) Press C or D to select “Parental”, then press ENTER. “Enter Pass word” screen will appear . 2) Press “0000” using Number buttons (0–9) .
53 Output You can select the video output signal of the DVD video player to the TV from “Interlace” or “Progres- sive”. RGB: Select when connecting to a composite TV. Component: Select when connecting to a TV equipped with component video inputs but progressive scan is not compatible.
54 T emporar y cancel the rating le vel by D VD disc Load a DVD disc and press PLAY or OPEN/ CLOSE on the unit (see page 33). Note: This temporary cancellation of rating level will be kept until the disc is ejected. When the disc is ejected, the original rating level will be set again automatically .
55 Language code list Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919 Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921 Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922 Albanian 2927 F.
56 SYMPTOMS POSSIBLE SOLUTIONS • Make sure the power cord is plugged in. • Try another AC outlet. • Power is off, check fuse or circuit breaker. • Unplug unit, then plug it back in. • Select the DVD or VCR mode before operating. DVD/VCR does not operate.
57 No subtitle. • Some discs hav e no subtitles. • Subtitles are cleared. Press SUBTITLE . Angle cannot be changed. • Multi-angles are not recorded on the D VD disc. • The function is prohibited with the unit or the disc. appears on the screen.
58 GENERAL Po w er supply: Po w er consumption: W eight: Dimensions: Input Le vel: Output Le vel: Hi-Fi F requency Response: Hi-Fi Dynamic Range: VCR section Video system: Video Head: A udio T rack: C.
59 2J50101A [EN] P56-Back 27/2/06, 5:41 PM 59.
Following information is only for EU-member states: The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly , you wil.
デバイスToshiba SD-37VBSBの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba SD-37VBSBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba SD-37VBSBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba SD-37VBSBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba SD-37VBSBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba SD-37VBSBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba SD-37VBSBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba SD-37VBSBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba SD-37VBSBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
