ToshibaメーカーSD-R1512の使用説明書/サービス説明書
ページ先へ移動 of 17
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-R1512 CD-R W/D VD-R OM COMBO DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the Com bo Drive ...........................
1 INTR ODUCTION – SD-R1512 General Features Reads and record s digital data on CD-R/-RW discs 3-way Disc Eject (ej ect button, software, emergency eject hole ) Average Random Access Time CD 100ms DV.
Front Panel Figure 1.SD-R1512 DVD Write able Drive Front Panel Loading Tray Load disc using tray. Busy Light LED The LED lights green or amber whe n the drive is operating (LED is amber whe n drive is writing.) Eject Button The Eject button is used to open the disc tra y so you can install or remove a disc.
3 SETUP – SD-R1512 The following steps must be performe d to properly install your drive: • Set Drive J umper Settings • Connect A udio Cab le • Attach IDE BUS Cable • Attach P ow er Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pi n s located on the rear of the Combo drive.
4 Placing Combo Drive inside your Computer Now that you have set the jumpers, you are read y to install your Combo drive inside your computer. Important Note: Disconnect power fr om your co mputer system before b eginning installation. Remove computer co ver and faceplate if required.
5 Audio Cable (optional) - If you have a sound card and speakers, and would like t o play audio CDs on your computer, you will need to install a CD/DVD audio ca ble. Toshiba's Combo drives use a sta ndard 4-pin audio cable that can be purchased from mo st local computer suppliers.
6 USING THE D VD Combo Drive – SD-R1512 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
7 Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the Combo drive, perform the following steps: 1. Open the Loading T r a y by pressing the Eject Button. 2. Slide disc holders a wa y from disc. 3. Grasp disc by edges , and lift out of loading tra y .
8 Emergency Ejection CAUTION: The following procedure is intended on ly as a last resort when pressing the eject button fails to open the Loading Tray 1. T ur n computer powe r OFF by properly shutting down system. 2. Inser t a solid bar (i.e. large paper clip) into Emergency Eject hol e and push in until loading t ra y opens.
9 TR OUBLESHOO TING – SD-R1512 Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instructi ons to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
10 SPECIFICA TIONS –SD-R1512 General Interface: ATAPI Applicable Formats - Write: Formats for Writing Disc at once, Track at once , session at once, Packet Write, increm ental write, restri cted ove.
11 Performance Rotational Speed DVD-ROM (single layer) DVD-ROM (dual layer) DVD-R (Ver. 2.0) DVD-R (Ver. 1.0) DVD-RW (Ver 1.1) DVD-RAM (Ver. 2.1) DVD-video (CSS-Disc) CD-ROM, CD-R CD-RW CD-DA Transfer CD-DA, Video-CD CD-R (Write) High Speed CD-RW (Write) CD-RW (Write) 7,580rpm (5.
12 Reliability MTBF 100,000 hours P ower ON Hours 5,436 hours/y ear ON/OFF Cycles 313 cycles/ye ar Number of Access 600,000 accesses/y ear Operating Duty Cycle 20% of P ower ON time (Reading/Seeki ng) 2% of P ower ON time (Writing/Seeking) MTTR 0.
13 Connectors DC input 4-pin P ower Suppl y Connector A T API Interf ace Connector 40 Pin I/F A T API Standard A udio Connectors 4-pin and 2-pin connector (use matching housing, P ar t No .
14 DRIVE CONNECT ORS –SD-R1512 Figure 1.SD-R1512 Combo Drive Rear Panel - Connectors Power Connector Power is supplied to your DVD d rive by the connection with your computer's +5V/+12V power cable to the power socket at the back of dri ve.
15 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
デバイスToshiba SD-R1512の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba SD-R1512をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba SD-R1512の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba SD-R1512の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba SD-R1512で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba SD-R1512を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba SD-R1512の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba SD-R1512に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba SD-R1512デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
