ToshibaメーカーSD-R5112の使用説明書/サービス説明書
ページ先へ移動 of 38
TOSHIBA STORAGE DEVICE DIVISION SD-R5112 DVD-R/-RW DRIVE PRODUCT SPECIFICATION MARCH 2003 REV. 1.0 Specifications are subject to change without notice DOCUMENT NUM BER 16004.
SD-R5112 Rev.1.0 LIMITATION OF LIABILITY Those warranties in the express warranty separately agreed between TOSHIBA and your company are the only warranties given to the consumer and are in lieu of any other warranties, whether express or implied with regard to this component.
SD-R5112 Rev.1.0 DO NOT use this equipment in the system such as medical equipment which may cause personal injury or property damages resulting from malfunction of this equipment and unexpected data corruption or data error in reading operation.
SD-R5112 Rev.1.0 6. As for mounting bracket to incorporate this product into an equipment, (1) When this product is incorporated into an equipment by using the mounting screw holes in the right and le.
SD-R5112 Rev.1.0 7. In the market, there are some drives or players that maintain to read CD or DVD disc, though, they may not designed to read CD-RW or DVD-RW disc. When you try to read the CD-RW or DVD-RW disc written by this product using other drives or players, please make sure that the equipment is applicable to CD-RW or DVD-RW disc.
SD-R5112 Rev.1.0 Contents 1. Introduction ---------------------------------------------------------------------------------------------------------------------- 1 2. Features -------------------------------------------------------------------------------------------------------------------------- 1 3.
SD-R5112 Rev.1.0 7.2. Current Drain ------------------------------------------------------------------------------------------------------- 22 7.2.1.Sleep ------------------------------------------------------------------------------------------------------------ 22 7.
1/29 SD-R5112 Rev.1.0 1. Introduction This document describes TOSHIBA's SD-R5112 DVD-R/-RW Drive. 2. Features This drive reads DVD CSS (Contents Scramble Systems) Disc. This drive reads digital data stored on CD-ROM, DVD-ROM and CD audio discs. This drive read and records the digital data on DVD-R/-RW and CD-R/RW discs.
2/29 SD-R5112 Rev.1.0 3. Specifications 3.1.Performance (1) Applicable Write Format DVD-R :Disc at once, Incremental write DVD-RW :Disc at once, Incremental write, Restricted overwrite CD-R/RW :Disc at once, Track at once, Session at once,Packet write (2) Applicable Write Disc * 1 DVD-R :DVD-R for General (Ver.
3/29 SD-R5112 Rev.1.0 (5) Rotational Speed DVD (Single) : Approx. 7,580 rpm (5.0-12X CAV) DVD (Dual) : Approx. 5,053 rpm (3.3-8X CAV) DVD-R Ver.1.0 : Approx. 3,200 rpm (2-4.8X CAV) DVD-R Ver.2.0 : Approx. 2,780 rpm (2-4.8X CAV) DVD-RW Ver.1.1 : Approx.
4/29 SD-R5112 Rev.1.0 (7) Access Time Average Random Access Time DVD* 2 : 130 ms Typ CD* 3 : 110 ms Typ DVD-RAM* 4 : 200 ms Typ Average Random Seek Time DVD* 5 : 120 ms Typ CD* 6 : 105 ms Typ DVD-RAM*.
5/29 SD-R5112 Rev.1.0 (9) Load/Eject (a) Electrical Load/Eject (Eject Button) (b) Load/Eject by ATAPI command (c) Emergency Eject (10) Air Flow Not Required (11) Acoustic Noise 40 dB (IEC 179 A weighted at 1 m) (12) Power Supply +5 V , +12 V (details in Section 7) 3.
6/29 SD-R5112 Rev.1.0 3.2.2.Dust and Dirt unspecified 3.2.3.Vibration (1) Operating (1 Oct/min) -------------------------- no hard error ----- 5 to 500 Hz 2.45 m/s 2 [0.25 G] ( 0-p) (excluding resonance point) (2) Operating (Write) (1 Oct/min) ---------------- no hard error ----- 5 to 500 Hz 2.
7/29 SD-R5112 Rev.1.0 3.3. Installation Conditions Mount the drive within 20 ° of the horizontal positions and within 10 ° of the vertical positions 20 ° 20 ° 20 ° 20 ° 20 ° 20 ° 20 ° a) Horizontal position 10 ° 10 ° 10 ° 10 ° b) Vertical position Figure 1 Installation position 3.
8/29 SD-R5112 Rev.1.0 189.5 +0.7 - 0.4 (Unit:mm) Figure 2-1 External Dimensions.
9/29 SD-R5112 Rev.1.0 (Unit:mm) Figure 2-2 External Dimensions.
10/29 SD-R5112 Rev.1.0 3.5. Reliabilites 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----- Allowing 5 Retries(default) ----- DVD: 10 -15 Max CD: Mode 1:10 -15 Max Mode 2:10 -12 Max (2) Seek Error Rate --- Allowing 5 Retries 10 -6 Max (default) 3.
11/29 SD-R5112 Rev.1.0 D VD-R/-RW DRIVE MODEL SD-R51 12 BLOCK DIAGRAM Disc Motor PUH F eed Motor P osition Detector R F Amp EQL T racking Amp Focus Amp T A1365AF P ower Driver P ower Driver BD7908 P o.
12/29 SD-R5112 Rev.1.0 5.Functions 5.1. Disc Data Configurations 5.1.1. DVD-ROM Data Configurations Figure 4 shows how data is constructed in the case of dual layer/parallel track data DVD disc. The DVD spec defines the single layer, the dual layer/opposite and parallel track disc, that the DVD-ROM drive supports.
13/29 SD-R5112 Rev.1.0 5.1.3. CD-R / CD-RW Data Configurations Before writing CD-R / CD-RW disc contains time-code information called ATIP. ATIP is abbreviation of "Absolute Time In Pre-groove" in the wobbling groove by modulating the carrier frequency.
14/29 SD-R5112 Rev.1.0 5.2. Power ON/OFF Timing (Target) Figure 8 shows the initialization sequence Power ON or ATAPI-RST System Initialization Focus Search Spindle ON Learning Stand-by "TEST UNIT READY" Command "Command" Receivable "Check Condition" Status "Good" Status Max.
15/29 SD-R5112 Rev.1.0 6.2.Signal summary The physical interface consists of single ended TTL compatible receivers and drivers communicating through a 50P-connector as shown in Figure 13 and Figure 14 "Interface connector". 6.2.1. Signal Specification Figure 9 shows the Signal Specifications N P N Sig.
16/29 SD-R5112 Rev.1.0 6.2.2. Timing of Host Interface (PIO) Figure 10 shows the Host Interface Timings. Address valid*1 DIOR-/DIOW- Write data valid*2 Read data valid*2 IOCS16- IORDY t4 t6 t7 t9 tA t.
17/29 SD-R5112 Rev.1.0 6.2.3.Timing of Host Interface (DMA Multi) Figure 11 shows the Host Interface DMA multi word Timings DMARQ DMACK-*1 DIOR-/DIOW-*1 Read DD0-15 Write DD0-15 tZ tI tJ tD tE tL tF tH tG t0 tK *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
18/29 SD-R5112 Rev.1.0 6.2.4.Timing of Host Interface (Ultra DMA ) Figure 12 shows the Host Interface Ultra DMA word Timings DMARQ DMACK- STOP DMARDY STROBE tMLI tUI tACK tFS tENV tZAD tZIORDY t2CYC t.
19/29 SD-R5112 Rev.1.0 6.3. Connector Figure 13 shows the mixture connector (Interface/Power supply) Table 2 shows Interface connector pin assignment. power supply connector PIN #1 : 12 V PIN #2 : GND PIN #3 : GND PIN #4 : +5 V 10.09 3.4 2.54 21.18 (2.
20/29 SD-R5112 Rev.1.0 CSEL Cable Select I - I / O I / O I / O I / O I / O PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 I / O SIGNAL.
21/29 SD-R5112 Rev.1.0 6.4. Support Command List ATAPI Packet Commands 00h Test Unit Ready 01h Rezero Unit 03h Request Sense 12h Inquiry 1Bh Start / Stop Unit 1Ch Receive Diagnostics 1Dh Send Diagnost.
22/29 SD-R5112 Rev.1.0 ATA Commands No OP Code Command Description 1 00h NOP 2 08h DEVICE RESET 3 20/21h READ SECTOR (S) 4 90h EXECUTE DEVICE DIAGNOSTICS 5 A0h PACKET 6 A1h IDENTIFY PACKET DEVICE 7 E0.
23/29 SD-R5112 Rev.1.0 8.CD Audio (Test condition: Ordinary temperature) 8.1. Analog Out --- in case of the attenuator is set at 0 dB by the command --- (1) Output Level 0.
24/29 SD-R5112 Rev.1.0 9. Device Configuration Jumper 9.1. Device configuration jumper (MODE SELECT) The device configuration jumper is a 6-pin, right angle and header (Molex P/N70203 or equivalent) with three marked positions.
25/29 SD-R5112 Rev.1.0 10. Busy Indicator The LED of Front Bezel indicates the drive status. (Busy Indicator) Color: Green (1) After Tray is closed, Busy Indicator start blinking at 0.8 s intervals, and then ----- (1-1) Turns off when the drive in the 'Idle' status.
26/29 SD-R5112 Rev.1.0 11.Connection 11.1. Power Supply Cable (1) Housing AMP JAPAN P/N 1-480424-0 or equivalent (2) Contact AMP JAPAN P/N 170148-2 or equivalent (3) Cable Length AWG #28 Max. 2 m 11.2. Interface Cable (1) Connector ATAPI specification (2) Cable 40 core type Specific Impedance 100 OHM +/-10 % (without shield) Length Max.
27/29 SD-R5112 Rev.1.0 13.Safety Standards/Agency Approvals (1) Safety EN60950 UL 1950 CAN/CSA-22.2 No.950 (2) Laser FDA 21CFR (U.S.A./DHHS) EN60825-1 (Europe) (3) EMC CE EN50081-1 : 1992 [Residental,.
28/29 SD-R5112 Rev.1.0 TOSHIBA TOSHIBA EUROPE GMBH EU-Declaration of Conformity Product: DVD-R/-RW Drive Manufacturer(s): Toshiba Corporation 1-1, Shibaura 1-chome, Minato-ku, Tokyo 105-8001 Japan See.
29/29 SD-R5112 Rev.1.0 EU-Declaration of Conformity ED-Directive Related Standard Issude Level/Test condition EMC-emission: EMC-immunity Product/Options Model Related EU-Directive 89/336/EEC X Manufac.
SD-R5112 Rev.1.0 Deviation List Page Item Rev # 0.9 Rev # 1.0 2 3.1.Performance (2) Applicable Write Disc DVD-R DVD-R (Ver2.0 for General) DVD-R for General (Ver2.01) Optional Spec. Rev.1.0 DVD-RW DVD-RW (Ver1.1) DVD-RW (Ver1.1) Optional Spec. Rev.1.0 (3) Applicable Read Disc DVD DVD-R (Ver.
SD-R5112 Rev.1.0 Page Item Rev # 0.9 Rev # 1.0 22 7.2.8.Write (CD-R 12/16X ZCLV) TBD mA 650 mA Write (DVD-R 4X CLV) TBD mA 600 mA 7.2. Current Drain (+12V) 7.2.1.Sleep TBD mA (DVD/CD) 60 mA (DVD/CD) 7.2.2.Standby TBD mA (DVD/CD) 60 mA (DVD/CD) 7.2.3.Continuous Read TBD mA (DVD) 600 mA (DVD) TBD mA (CD) 700 mA (CD) 7.
デバイスToshiba SD-R5112の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba SD-R5112をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba SD-R5112の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba SD-R5112の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba SD-R5112で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba SD-R5112を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba SD-R5112の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba SD-R5112に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba SD-R5112デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
