ToshibaメーカーW-707の使用説明書/サービス説明書
ページ先へ移動 of 49
V ideo Cassette Recor der W -707 OWNER’S MANUAL This publication is printed on recycled paper 70971855 PLAY STOP PROG.TV POWER EJECT PAUSE/STILL REC REV FF.
2 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
3 INTRODUCTION IMPOR T ANT PRECA UTIONS Save Original Packing Materials The original shipping carton and packing materials will come in handy if you ever have to ship your VCR. For maximum protection, repack the set as it was originally packed at the factory.
4 1. Read owner’s manual After unpacking this product, read the owner’s manual carefully, and follow all the operating and other instructions. 2. Power Sources This product should be operated only from the type of power source indicated on the marking label.
5 INTRODUCTION 6. Water and Moisture Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like. 7. Cleaning Unplug this product from the wall outlet before cleaning.
6 16. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen into the product.
7 INTRODUCTION INTRODUCTION Provides important notes and general explanation of the VCR, including names of the buttons, jacks, etc. SAFETY PRECAUTIONS .................... 2 IMPOR T ANT PRECA UTIONS ............. 3 IMPOR T ANT SAFETY INSTRUCTIONS ...
8 Fr ont Panel Remote Control INTRODUCTION Identification of Controls See the page in for details. This manual shows the names of buttons in italics. To operate this VCR.
9 INTRODUCTION Rear Panel LINE IN 1 A UDIO (Rear), 2 (Front) jac ks If the connected equipment is monaural (has one audio output jack), connect the L (MONO) side, the same sound is recorded on both L and R on the Hi-Fi track.
10 Setting up the Remote Contr ol 1 Open the batter y compar tment lid on the rear panel. 2 Install 2 batteries (“AAA” size) f ollowing the polarity diagrams. 3 Close the batter y compar tment lid. 4 P oint the remote control at the VCR and press the buttons within the oper ating range.
11 PREP ARA TION Antenna/VCR/TV Connection 1 Disconnect the antenna cab le from your TV and connect it to the RF IN terminal on the VCR. 2 Connect the RF OUT terminal to the TV . AUDIO/VIDEO Connections The A UDIO/VIDEO jacks are also a vailab le to connect y our TV .
12 Cable Connection Choose one of the below according to y our usage of the cable bo x. This set-up will enable you to: – record an unscramb led channel. – watch an unscramb led channel while recording it. – record an unscramb led channel while watching another (only when y ou connect a cable- compatible TV).
13 PREP ARA TION This set-up will enable you to: – watch an unscramb led or scrambled channel while recording it. – record any channels through the cab le box.
14 Auto Set Up 1 Connect the antenna cable to the VCR (see page 11). Then connect the VCR’ s pow er plug to an A C outlet. “A uto” flashes in the VCR displa y as the VCR automatically tunes in all activ e stations. When A uto Set Up is completed successfully , the current time will be display ed.
15 PREP ARA TION SET UP PROGRAM PRESET PROG H 120 0 16 80 1 OF F O OF F O U AT O U A M EG R FA S P E TA P E LE SAP S E T SI M U L C A S T GT AN T E A LA n nn n n n OF F O n n GUA G X DS I n O F E n ED : n Optional settings on the SET UP screen Other optional settings can be made .
16 Setting the Clock Example: T o set the clock to 2:30 p .m. on A ugust 25 (summer time) 2000. 1 Press PROG . The MENU screen appears on the TV . 2 Select “PRESET” using CURSOR RIGHT or CURSOR LEFT , and press ENTER . 3 Press ENTER to select “CLOCK SET”.
17 PREP ARA TION Incoming Antenna/Cable (CA TV) Signals The VCR scans through all receivab le TV and CA TV channels and stores only the activ e ones in your area into the memory . Once the storing is finished, y ou can select a desired channel using CH .
18 To add channels To erase channels Adding or erasing channels Adding channels If a desired channel cannot be scanned automatically because of a weak signal, it can be added to the memor y . Erasing channels Y ou can erase a stored channel from the memory if it is unnecessar y .
19 PREP ARA TION V ideo Cassette Use Loading a cassette Push the cassette into the cassette compar tment with the window side f acing up and the label side tow ards the front. The VCR is automatically turned on. The indicator will appear in the VCR display .
20 Adjusting the tracking When pla yback star ts, the VCR automatically adjusts the trac king for clear pictures and sound (Digital A uto T rac king). The “DT” indicator blinks during the adjusting. If the VCR cannot locate the best possible trac king point, hold down one of CH/TRK to adjust the trac king manually .
21 PLA YBA CK PLA YBA CK V ariable Speed Playbac k You can play back a tape at various tape speeds. Picture Search A tape runs at 5 times or 7 times the nor mal playbac k speed so that you can quic kly locate a par ticular scene. 1 Press FF or REW dur ing pla yback.
22 Frame Advance A picture adv ances frame by frame . 1 Press PLA Y dur ing still pla yback. Each time you press PLA Y , the picture advances one fr ame. If you press and hold PLA Y , the tape runs at 1/30th the nor mal pla yback speed. To resume normal playback Press P A USE/STILL .
23 PLA YBA CK Counter Function Y ou can view the cloc k, linear time counter or tape remaining time in the VCR display or on the TV screen. 1 Each time y ou press REMAIN/COUNTER , the VCR display changes in sequence as f ollows: The indication abov e will also appear on the TV screen by pressing DISPLA Y .
24 Index Search Function The VCR can find a point where a registered index signal is on a tape and pla y back f or about 5 seconds. Y ou can easily locate the desired progr am by inputting the inde x signal. Registering index signals Each time a recording star ts, an inde x signal is automatically registered.
25 RECORDING W atching a TV program while recording another 1) While recording, press TV/VCR to tur n off “VCR” indicator . 2) Choose another channel using the channel selector on the TV . Skipping unnecessary scenes while recording Press P A USE/STILL to stop recording momentarily .
26 Timer Pr ogramming Procedure Example : T o record cable channel 25 in the SP tape speed from 9:30 p .m. until 10:00 p .m. on A ugust 30. T oda y is August 25. 1 Load a cassette with the saf ety tab attached. 2 Press PROG to displa y the MENU screen.
27 RECORDING 5 Move to the next using CURSOR RIGHT , and set the recording date using CURSOR UP or CURSOR DO WN . The date changes as follows: [WKL YSU] … [WKL YSA]: Y ou can record TV progr ams on the same channel on the day and time every week.
28 If a power failure occurs during the timer program recording (including VCR Plus+ C 3 ® system recording (page 31)) • When a pow er f ailure has occurred, “- -:- -” appears in the VCR displa y . Since the progr ammed contents ha ve been cleared, reset the clock and timer prog ramming.
29 RECORDING RECORDING The flow char t below will giv e y ou an idea as to what must be done to use the VCR Plus+ C 3 ® system feature. Setting the Clock (page 16) ↓ Cable Box Set-up (page 33) ↓ .
30 Guide Channel Setting 1 Press PR OG . 2 Select “PRESET” using CURSOR RIGHT or CURSOR LEFT , and press ENTER . 3 Select “CH MEMOR Y” using CURSOR UP or CURSOR DO WN , and press ENTER . 4 Set “TV/CA TV” to “TV” or “CA TV” using CURSOR RIGHT or CURSOR LEFT .
31 RECORDING VCR Plus+ C 3 ® system Pr ogramming 1 Press VCR Plus+ . The VCR Plus+ screen appears. 2 Enter a PlusCode ® programming number . Example : T o record a program with the PlusCode ® programming number 36295 (fictitious code). Press number b utton 3, 6, 2, 9 and 5 .
32 Confirming the VCR Plus+ C 3 ® system timer pr ograms Before the VCR enters the timer standby mode (TIMER indicator not lit) 1) Press PR OG to displa y the MENU screen. 2) Press ENTER to select “PROGRAM”. Check the progr ammed data. 3) Press PR OG to e xit.
33 RECORDING Cable Box Set-up The VCR can directly control channel selecting of the connected cable box. RECORDING Cable Box Contr ol This VCR needs to be connected to a cab le bo x equipped with an infrared wireless remote control. Y ou can select cable channels from the cab le box b y operating this VCR.
34 Cable Box Set-up (continued) Cable Box Set-up 1 Press PR OG. to displa y the MENU screen. 2 Select “PRESET” using CURSOR RIGHT or CURSOR LEFT , and press ENTER . 3 Select “CABLE BO X/DSS” using CURSOR UP or CURSOR DO WN , and press ENTER . 4 Select “NO” or “C.
35 RECORDING VCR display Cable box display Cable channel number 7 Select “BRAND TYPE” using CURSOR DO WN , and enter a brand code of y our cable bo x using number b uttons . Ref er to the table on the next page. Example : For a T OSHIBA cab le box, identified b y number 36.
36 T able of cable box brand codes Toshiba 36 Anvision 13, 20, 21, 22, 23, 24, 25, 26, 58, 62, 84 Archer 1, 20, 21, 29, 42, 44, 63, 88, 91 Cablestar 13, 20, 21, 22, 23, 24, 25, 26, 58, 62, 84 Cablevie.
37 RECORDING DSS ® Satellite Receiver Set-up The VCR can directly control channel selecting of the connected DSS ® satellite receiver. RECORDING DSS ® Satellite Receiver Control This VCR needs to be connected to a DSS ® satellite receiv er equipped with an infrared wireless remote control.
38 DSS ® Satellite Receiver Set-up (continued) DSS ® Satellite Receiver Set-up 1 Press PR OG. to displa y the MENU screen. 2 Select “PRESET” using CURSOR RIGHT or CURSOR LEFT , and press ENTER . 3 Select “CABLE BOX/DSS” using CURSOR UP or CURSOR DO WN , and press ENTER .
39 RECORDING Buttons to control a remote- controllable DSS ® satellite receiver Once you complete the set-up f or a remote controllable DSS ® satellite receiv er , y our DSS ® satellite receiver can be controlled b y the follo wing buttons on the remote control of the VCR.
40 MTS Broadcast Compatibility This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to your stereo system or stereo TV, you will experience the SAP or stereo sound. Preparation Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.
41 RECORDING Simulcast Recording When TV program such as MTV, HBO or MAX is being simulcast in FM stereo in your area, the VCR can also record the simulcast sound from an FM stereo tuner or receiver onto the Hi-Fi track and normal track. Preparation • Connect the TV and stereo system to the VCR as below.
42 Setting Control Codes 1 Press TV to set the remote control operating y our TV . 2 While holding down PROG , enter the two digits of y our TV’ s brand code (listed right) using number b uttons . 3 Release PROG . 4 P oint the remote control at your TV and use each button listed belo w to make sure that your TV is operated correctly .
43 ADDITIONAL INFORMA TION Toshiba 01 Bell & Howell 09 Carver 10 Celebrity 03 Citizen 12 Curtis Mathes 09, 12 Dumont 14 Electro band 03 Emerson 09, 11 Fisher 09 GE 02, 07, 11 Gibralter 14 Goldstar.
44 No power . • The power cord is not plugged in. – Plug the power cor d into the outlet firmly . Although the power is on, the VCR will not work. • There is no cassette. – Load a cassette. (page 19) The clock does not work. • There has been a power failure.
45 ADDITIONAL INFORMA TION The remote control does not work properly . • The batteries are exhausted. – Replace all batteries. (page 10) • The remote control is operated beyond the operating range. – Make sure the remote control is within 30° of the remote sensor on the VCR.
46 Specifications Power supply: 120 V AC, 60 Hz Power consumption: 19 W External dimensions: 430 × 96.5 × 281 mm (W.H.D.) Mass: 3.8 kg Channels received: VHF: Channels 2–13 UHF: Channels 14–69 C.
47 ADDITIONAL INFORMA TION LIMITED W ARRANTY T OSHIB A VIDEO CASSETTE RECORDER Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii Inc.
LIMITED W ARRANTY (continued) How to Obtain Warranty Service (1)Refer to the troubleshooting guide in your owner's manual. This check list may solve your problem. (2)Call the TACP toll free number 800-631-3811 within (30) days after you find a defective product or part.
SECTION 2 ADJUSTMENT PR OCEDURES 1. MECHANICAL ADJUSTMENT 1-1. Mechanical Parts Location 1-2. Servicing Jig List 1-3. Ma in Par ts Ser vicing Time 1-4. Mechanism Check Method 1-5. M echanical Deck Removing and Mounting Method 1-6. Main Parts Replacement 1-7.
デバイスToshiba W-707の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Toshiba W-707をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba W-707の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba W-707の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba W-707で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba W-707を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba W-707の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba W-707に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba W-707デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
