ToshibaメーカーX500の使用説明書/サービス説明書
ページ先へ移動 of 277
Qosmio X500 Maintenance Manual (960-Q08) Toshiba Personal Computer Qosmio X500 Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08.
Qosmio X500 Maintenance Manual (960-Q08) Copyright © 200 9 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein.
Qosmio X500 Maintenance Manual (960-Q08) Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Qosmio X500 Series. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
Qosmio X500 Maintenance Manual (960-Q08) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Qosmio X500 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems.
Qosmio X500 Maintenance Manual (960-Q08) Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition.
Qosmio X500 Maintenance Manual (960-Q08) Table of Contents Chapter 1 Contents 1.1 Features ................................................................................................................... .......1 1.2 System Block Diagram ..........
Qosmio X500 Maintenance Manual (960-Q08) Chapter 2 Troubleshooting Procedures 2.1 Troubleshooting ........................................................................................................... .1 2.2 Troubleshooting Flowchart ............
Qosmio X500 Maintenance Manual (960-Q08) 2.9 Display Troubleshooting..............................................................................................28 Procedure 1 Extern al Monitor Check...................................................
Qosmio X500 Maintenance Manual (960-Q08) Chapter 3 Diagnostic Programs 3.1 Tests and Diagnostics Software Overview .............. 3- Error! Bookmark not defined. 3.2 Executing the Diagnostic Test ................................. 3- Error! Bookmark not defined.
Qosmio X500 Maintenance Manual (960-Q08) Chapter 4 Replacement Procedures 4.1 Overview ................................................................................................................... .4 - 1 Safety Precautions ......................
Qosmio X500 Maintenance Manual (960-Q08) 4.21 Web Camera m odule ................................................................................................ 4-62 4.22 Speaker Box ...................................................................
Qosmio X500 Maintenance Manual (960-Q08) Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ............................................................
Qosmio X500 Maintenance Manual (960-Q08).
Qosmio X50 0 Maintenance Manual (960- Q08) Chapter 1 Hardware Overview.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) ii 1 Hardware Overview Chapter 1 Contents 1.1 Features ................................................................................................................... .......1 1.
Hardware Overview Chapter 1 Qosmio X50 0 Maintenance Manual (960- Q08) iii Figures Figure 1-1-1 Front of the computer.........................................................................................4 Figure 1-2-1 System block diagram for AMD platform .
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) 1 Features 1.1 Features The Qosmio X500 features are listed below. Microprocessor Microprocessor that is used will be d ifferent by the model. It supports processors as follows Intel® Core(TM) i7-720QM processor 1.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 2 Keyboard module has104/105/109 keys. It supports Windows keys and application keys. New Dummy card slot The new card slot (dummy card) accommodates express card. Optical devices A DVD Super Multi drive is equipped.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) 3 Bridge media slot XD/MS/MS pro/SD/MMC are supported Bluetooth Some computers in this series of fer Bl uetooth wireless communication functiona lity. This module is Version 2.
Chapter 1 Hardware Overview 1. Web Camera LED* 2. Web Camera* 3. Built-in microphone* 4. Wireless LAN/Wireless WAN Anten n as (Not shown) 5. Speaker 6. Touch Pad 7. Fingerprint Sensor* 8. Touch Pad Control Buttons 9. Display Screen 10. Speaker 11. Power Button* 12.
Chapter 1 Hardware Overview 1.2 System Block Diagram Figure 1-2-1 shows the system block diagram. Figure 1-2-1 System block diagram for Intel Platform 5 Qosmio X50 0 Maintenance Manual (960- Q08).
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 6 The PC contains the following components. CPU Intel® Core(TM) i7-720QM processor 1.6GHz, 1.73GHz Memory DDR3-1066MHz 1GB, 2GB or 4GB memory m odules 200-pin SO-DIMM 1.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) 7 Other main system chips • Clock Generator • EC/KBC –[W/CIR(Winbond WPCE 775CA0DG)] –[WO/CIR(Winbond WPCE775.
Chapter 1 Hardware Overview 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3-1 shows a view of the 2.5-inch HDD and Tables 1-3-2 and 1-3-3 list the specifications.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) 9 Standard value Parameter HITACHI HTS545016B9A 300 HITACHI HTS545025B9 A300 HITACHI HTS545032 B9A300 HITACHI HTS545040 B9A300 HITACHI HTS545050B9A 300 Width (mm) 69.85 +/- 0.25 Height (mm) 9.
Chapter 1 Hardware Overview Specification Parameter FUJITSU MJA2160BH FUJITSU MJA2250BH FUJITSU MJA2320BH FUJITSU MJA2400BH FUJITSU MJA2500BH Storage size (format ted) 160GB 250GB 320G B 400GB 500G B .
Chapter 1 Hardware Overview 1.4 Optical Drive (HD DV D-ROM & CD-R/RW Drive) The DVD Super Multi drive accommodates eith er 12 cm (4.72-inch) or 8 cm (3.15-inch) CD/DVD-ROM, CD-R/RW, DVD±R/±RW and DVD-RA M. It is a high-performance drive that reads DVD-ROM at maximum 8-speed a nd CD at maximum 24-sp eed.
Chapter 1 Hardware Overview Table 1- 4-2 DVD Super Multi drive outline dimensions Parameter Standard value Maker HLDS (GT20N-ATAK7N7 ) HLDS (GT20F-ATAK7 N7) Width (mm) 128 Height (mm) 12.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) 13 Table 1- 4-3 HLDS DVD Super Multi drive specifications HLDS Drive Specification Parameter GT20N-ATAK7 N7 GT20F-ATAK7N7 Label Flash Function No support Support Read DVD-ROM 8x max.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 14 Table 1- 4-4 Panasonic DVD Super Multi drive specifications Panasonic Drive Specification Parameter UJ240/UJ890ADTJR-A UJ141.
Chapter 1 Hardware Overview Table 1- 4-5 TSST DVD Super Multi drive specifications 15 Qosmio X50 0 Maintenance Manual (960- Q08).
Chapter 1 Hardware Overview 1.5 Keyboard The Qosmio X500 keyboard has two different kinds of placement, one is for US style and the other is for UK style.
Chapter 1 Hardware Overview 1.6 TFT Color Display The Qosmio X500 Ganel use CCFL to control backlight. 1.6.1 LCD Module with CCFL Backlight Figure 1-6-1 shows a view of the LCD module and Table 1-6- 2 lists the specifications.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 18 Table 1-6-2 LCD module specifications Specifications(WXGA+) Item Samsung LTN184K T02-T0 1 Samsung LTN184H T04-T0 1 Number of Pixel 1680 x 945 1920 x 1080 Dot spacing (mm) 0.243 (H) × 0.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Manual (960- Q08) 19 1.6.2 CCFL Inverter Board Table 1-10 lists the FL inve rter board specifications. Table 1-6-3 FL inverter board specifications Specifications Item SUMIDA TWS-449-341 Am p ow er T18I107.
Chapter 1 Hardware Overview Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 20 1.7 Power Rails Table 1-7-1 lists the power rail output specifications. Table 1-7-1 Power supply output rating Power supply .
Chapter 1 Hardware Overview 1.8 Batteries The PC has the following two batteries. Main battery Real time clock (RTC) battery Table 1-8-1 lists the specification s f or these two batteries.
Chapter 1 Hardware Overview 1.8.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and dete cts a full charge when the AC adaptor and battery are connected to the computer.
Chapter 1 Hardware Overview Table 1-8-3 Data retaining time * If USB Seep and Charge function is enabled, the computer’s battery will discharge during hibernation or when the computer is turned off.
Chapter 1 Hardware Overview 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory.
Chapter 1 Hardware Overview 1.9 AC Adapter Table 1-9-1 lists the AC adapter specifications. Table 1-9-1 AC adapter specifications 25 Qosmio X50 0 Maintenance Manual (960- Q08).
2-1 Qosmio X500 Maintenance Manual ( 960-Q08) Chapter 2 Troubleshooting Procedures.
2-2 Qos mio X500 Maintenan ce Manual (9 60-Q08) Chapter 2 Contents 2.1 Troubleshooting .............................................................................................................1 2.2 Troubleshooting Flowchart .......................
Qosmio X50 0 Maintenance Ma nu al (9 60 - Q0 8) 2-3 2.9 Display Troubleshooting ..............................................................................................28 Procedure 1 External Monitor Check .......................................
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 1 2 2.1 Troubleshooting Chapter 2 describes how to determine which Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1.
2 Troubleshooting Procedures There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is descri bed in the figure as line. (2) Pin connection is describe d in the figure as arrow.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 3 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1-1 as a guide for determining which troubleshooting procedures to execute.
2 Troubleshooting Procedures Figure 2-1-1 Troubleshooting flowchart (1/2) 4 Qosmio X50 0 Maintenance Manual (960- Q08).
2 Troubleshooting Procedures Figure 2-1-2 Troubleshooting flowchart (2/2) If the diagnostics program cannot detect an e rror, the problem may be intermittent.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 6 function to confirm which diagnostic test de tected an error(s), and then perform the appropriate troubleshooting procedures as follows: 1.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 7 2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 8 Table 2-2 DC IN icon DC IN icon Power supply status Lights red DC power is being supplie d from the AC adapter. Blinks orange Power supply malfunctio n *1 Doesn’t light Any condition other than those above.
2 Troubleshooting Procedures Procedure 2 Connection Check The wiring diagram related to th e power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord is firmly plugged into the DC IN connector PCN3 and wall outlet.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 10 adjust it in the right temperature. If th e battery pack is s till n ot charged, go to Check 5. Check 5 Replace the battery pack with a new one . If the battery pack is still not ch arged, go to Procedure 4.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 11 Procedure 4 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 12 2.4 System Board Troubleshooting This section describes how to determ ine if th e system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 13 Procedure 1 Message Check When the power is turned on, the system perfor ms the Power On Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the system board and initializes it.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 14 Procedure 2 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these tests.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 15 2.5 USB FDD Troubleshooting To check if the USB FDD is malfunctioning or not, follow the troubl eshooting procedures below as instructed.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 16 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, tu rn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation about th e diagnostics test procedures.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 17 Procedure 3 Connector Check and Replacement Check USB FDD is connected to USB port on system board and US board. US board is also connected to system board by cable.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 18 Check 2 USB FDD may be fau lty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 Connect USB FDD to each port embedded on system board. If it does not work properly, perform Check 4.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 19 2.6 2.5” HDD Troubleshooting To check if 2.5” HDD is malfunctioning or not, follow the troubleshooting procedures below as instructed.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 20 Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960-Q08) 21 Procedure 3 Format Check The computer’s HDD is formatted using the Free-DOS FORMAT program or the physical format program of the test program. To fo rmat the HDD, start with Check 1 below and perform the other steps as required.
2 Troubleshooting Procedures Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program.
2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check HDD(s) is/are connected to the connector(s) on the system board. Th e connection of HDD(s) and board may be defective. Otherwise, they may be faulty. Disassemble the com puter following instructions in Chapter 4, Replacement Procedures and perform the following checks.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 24 2.7 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed.
2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty.
2 Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 26 2.8 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed.
2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the cable is fi rmly connected to system board.
Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 28 2.9 Display Troubleshooting To check if the computer’s display is ma lfunctioning or not, follow the troubleshooting procedures below as instructed.
Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD/FL cable. FL inverter board is also connected to system board by an LCD/FL cable . And, fluorescent lamp is connected to FL inverter board by HV cable.
Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 30 Procedure 4 Replacement Check Fluorescent lamp, FL inverter, LCD module, HV cable and LCD/FL cable are connected to display circuits.
Troubleshooting Procedures 2.10 Optical Disk Drive Troubleshooting To check if optical disk drive is malfunctioni ng or not, follow the troubleshooting procedures below as instructed.
Troubleshooting Procedures 2.11 Modem Troubleshooting To check if modem is malfunctioning or not, fo llow the troubleshooting procedures below as instructed.
Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 33 Check 2 Modem cable m ay be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 MDC may be faulty. Replace it with a new one following the steps in Ch apter 4.
Troubleshooting Procedures 2.12 LAN Troubleshooting To check if the computer’s LAN is malfunc tioning or not, follow the troubleshooting procedures below as instructed.
Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 35 2.13 Wireless LAN Troubleshooting To check if the computer's W ireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed.
Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiri ng diagram is shown below: Any of the connections may be defective.
Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 37 Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty.
Troubleshooting Procedures 2.14 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check Procedure 2: Replacement Check Procedure 1 Connector Check The connection of sound system is shown in the following figure.
Troubleshooting Procedures Qosmio X50 0 Maintenance Manual (960- Q08) 39 Procedure 2 Replacement Check If External microphone/Headphone does not work properly, perform check 1. If Internal microphone /Speaker does not work properly, perform check 2.
Troubleshooting Procedures 2.15 Fingerprint Troubleshooting To check if the computer’s Fingerprint is ma lfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute Fingerprint test in the test program .
Troubleshooting Procedures 2.16 Bluetooth Troubleshooting To check if the computer’s B lue tooth is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Connector Check and Replacement Check The B lue tooth module is connected to system board.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 1 Chapter 3 Diagnostic Programs.
Test Program for Field. 2 Qosmio X500 Maintenance Manual (960-Q08) Chapter 3 Contents 3.1 ............................................................ 3-3 Tests and Diagnostics Software Overview 3.2 ....................................................
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 3 3.1 Tests and Diagnostics Software Overview This chapter explains how to use the Tests and Diagnostics Software for the Satellite P500 and Satellite Pro P500 computer systems. NOTES : Before starting the Tests and Diagnostics software: 1.
Test Program for Field. 3.2 Executing the Diagnostic Test DOS is required to run the Diagnostics Program. To start the programs follow these steps: 1. Create a DOS bootable disk and copy all the files from the Tests and Diagnostics software to the disk.
Test Program for Field. The following menu displays: :Select item Enter:Decision item Esc:Escape TOSHIBA Satellite(Pro) P500 Diagnostics Version V1.10 [ DIAGNOSTICS MENU ] 01. DIAGNOSTIC TEST 02. RUNNING TEST 03. DMI INFORMATION 04. LOG UTILITIES 05. SYSTEM CONFIGURATION ::Select item ESC :Escape 06.
Test Program for Field. 4. Select the subtest you want to execute and press Enter . The following menu displays: 6 Qosmio X500 Maintenance Manual (960-Q08) 5. Select the desired test from the subtest menu and press Enter . The following Test Parameter menu displays: [ DIAGNOSTICS MENU ] 01.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 7 NOTES : The Item2 and 3 of Test Parameter are not used by some tests. Go To Test Move the highlight bar to Go To Test and press Enter to start executing the test. Test Loop Select NO to return the screen to the subtest menu after the test is com plete.
Test Program for Field. 8 Qosmio X500 Maintenance Manual (960-Q08) 3.3 Subtest names Table 3-1 lists the subtest names for each test program in the Diagnostic Test menu.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 9 Table 3-1 Subtest Names(2/3) No. Test Name No. Subtest Name 05 FLOPPY DISK TEST 01 02 03 04 05 Sequential Read Sequential W/R/C Rando.
Test Program for Field. 10 Qosmio X500 Maintenance Manual (960-Q08) Table 3-1 Subtest Names(3/3) No. Test Name No. Subtest Name 10 MULTIMEDIA TEST 01 02 03 04 Sequential Read Test Random Read Test Rea.
Test Program for Field. 3.4 System Test To execute the System Test select 01 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The System Test contains three subtests. Move the highlight bar to the subtest you want to execute and press Enter .
Test Program for Field. 12 Qosmio X500 Maintenance Manual (960-Q08) Subtest 03 CPU Temperature This will display CPU Temperature for check , press [ESC] to exit . [CPU_TEMP.EXE] Program Version : 1.3 03-09-2009 CPU Temperature : XX GPU Temperature : XX NOTES : If no external Graphics , GPU not report temperature .
Test Program for Field. The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green. Set method of PC 3 Test1 Judgment If all data is less than ranges, it will be OK.
Test Program for Field. The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 4 Test2 Judgment If all data is less than ranges, it will be OK.
Test Program for Field. The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Qosmio X500 Maintenance Manual (960-Q08) 15 5 Test3 Judgment If all data is less than ranges, it will be OK.
Test Program for Field. The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 16 Qosmio X500 Maintenance Manual (960-Q08) 6 Test4 Judgment If all data is less than ranges, it will be OK.
Test Program for Field. The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC 7 Test5 Judgment If all data is less than ranges, it will be OK. 8 Inspection Judgment If all data is less than ranges, it will be OK.
Test Program for Field. 18 Qosmio X500 Maintenance Manual (960-Q08) 3.5 Memory Test To execute the Memory Test select 02 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Memory Test contains five subtests that test the computer’s mem ory.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 19 5. Address pattern test “16 bit write and 16 bit read” of address pattern data is executed and the new data is compared with the original data. Test data = 0000H, 0004H, 0008H, 000CH,.
Test Program for Field. 20 Qosmio X500 Maintenance Manual (960-Q08) with the original data patterns. Addresses are displayed in 64KB increments during the test. Test Process: 1. Byte Enable Test One bit write/ 8 bit read” is executed and the new data is compared with the original data.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 21 Test Process: 1. Checks the memory size to determ ine the maximum size of installed memor y. 2. Tests memory addresses 0 to the m aximum installed. 3. Writes, reads, and compares test data after a m emory refresh cycle (16ms or more).
Test Program for Field. 3.6 Keyboard Test To execute the Keyboard Test select 03 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Keyboard Test contains five subtests that test the computer’s keyboard and mouse actions.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 23 Subtest 04 Hot Key Display [9 Key] This subtest is used for the 9 hot key and functions the same as Subtest 1. ECO MUTE MUSIC PLAY BACK NEXT VOL- VOL+ WLAN Subtest 05 Hot Key Display [1 Key] This subtest is used for the 1 hot key and functions the same as Subtest 1.
Test Program for Field. LEFT PRESS RIGHT PRESS TOUCH_PAD TEST Please Do Not Press the Left and Right Button At The Same Time 24 Qosmio X500 Maintenance Manual (960-Q08).
Test Program for Field. 3.7 Display Test To execute the Display Test select 04 from the Diagnostic Test Menu, press Enter and follow the directions displayed on the screen. The Display Test contains twelve subtests that test the display in various modes.
Test Program for Field. Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu. Subtest 02 Character Set This subtest displays the character codes 00H - FFH, using Mode 01H (40*25).
Test Program for Field. Subtest 03 80 * 25 Character Display This subtest uses 80*25 video resolution to display character codes 20H - 7EH using Mode 03H (80*25).
Test Program for Field. Subtest 04 320 * 200 Character Display This subtest uses 320*200 video resolution to display green, red and yellow followed by cyan, magenta, and white.
Test Program for Field. 320*200 GRAPHICS DISPLAY : [ D ] BLACK D GRAY BLUE L BLUE GREEN L GREEN CYAN L CYAN RED L RED MAGENTA L MAGENTA BROWN YELLOW WHITE I WHITE Press [Enter] KEY Press ENTER to disp.
Test Program for Field. Subtest 05 640 * 200 Character Display This subtest uses 640*200 video resolution to display three windows, each window drives a different set of dots: even dots, odd dots and all dots. The screen below displays when this subtest is executed.
Test Program for Field. Subtest 06 640 * 480 Character Display This subtest uses 640*350 video resolution to display 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white.
Test Program for Field. 640*480 GRAPHICS DISPLAY : [12 ] BLACK DARK GRAY BLUE LIGHT BLUE GREEN LIGHT GREEN CYAN LIGHT CYAN RED LIGHT RED MAGENTA LIGHT MAGENTA BROWN YELLOW WHITE INTENSIFIED WHITE Press [Enter] KEY To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Test Program for Field. Subtest 07 Display Page This subtest displays video pages zero through seven. DISPLAY PAGE 0 000000000000000000000000000000000000000000000000000000000000000 0............................................................0 0......
Test Program for Field. Subtest 08 "H" Pattern Display This subtest displays a full screen of "H" patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HH.
Test Program for Field. Subtest 10 Color Graphics Display This subtest displays three colors, cyan, white and yellow on the screen as shown below. 640 * 480 GRAPHICS DISPLAY CYAN WHITE YELLOW To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu.
Test Program for Field. Subtest 11 Color Attributes Display This subtest displays 16 colors: black, blue, green, cyan, red, magenta, brown, white, dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and intensified white.
Test Program for Field. NOTE: The following screen does not display correctly. It will be amended in the next version. Qosmio X500 Maintenance Manual (960-Q08) 37 Press [Enter] Key Press Enter to execute the VRAM mapping test which displays a vertical line at four dot intervals using Mode 12.
Test Program for Field. 38 Qosmio X500 Maintenance Manual (960-Q08) Press [Enter] Key To exit this subtest and return to the Display Test menu: Press Enter if NO was selected for Test Loop on the Test Parameter Menu. Press Ctrl + break if YES was selected for Test Loop on the Test Parameter Menu.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 39 Subtest 12 Color Tiling This subtest displays black, gray, white, and 3 gradations of red, green, and blue as shown in the following display.
Test Program for Field. 40 Qosmio X500 Maintenance Manual (960-Q08) 3.8 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the diagnostics disk and insert the work disk into the FDD. The contents of the floppy disk will be erased.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 41 Subtest 04 Write Specified Address NOTE : The first two digits of the ADDRESS indicate which track is being tested, the next two digits indicates the head, and the last two digits indicate the sector.
Test Program for Field. 42 Qosmio X500 Maintenance Manual (960-Q08) 3.9 Hard Disk Test To execute the Hard Disk Test select 06 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Hard Disk Test contains eight subtests that test the functions of the hard disk drive.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 43 Subtest 04 Cross Talk and Peak Shift This subtest writes eight of the most likely to fail data patterns (shown below) to a cylinder on the HDD, then reads the data while moving from cylinder to cylinder.
Test Program for Field. 44 Qosmio X500 Maintenance Manual (960-Q08) Subtest 07 Sequential Write This subtest writes specified data to all cylinders on the HDD.
Test Program for Field. 3.10 Real Time Clock Test To execute the Real Time Clock Test select 07 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Real Time Clock Test contains three subtests that test the computer’s real time functions.
Test Program for Field. Subtest 02 Backup Memory This subtest writes 50 bytes of test data (FFH, AAH, 55H, and 00H) to the CMOS 14 th address, then reads the new data and compares it to the original data. Subtest 03 Real Time Carry CAUTION : When this subtest is executed, the current date and time are reset.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 47 3.11 Cache Memory Test To execute the Cache Memory Test select 08 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Cache Memory Test contains eight subtests that test the computer's cache m emory.
Test Program for Field. 48 Qosmio X500 Maintenance Manual (960-Q08) Subtest 04 Bit Shift Pattern Test This subtest reads the contents of cache memory and saves it into RAM. The subtest then writes the bit shift data patterns (1 bit shifted every 4 bytes ), reads the new data and compares the result with the original data.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 49 3.12 High Resolution Display Test To execute the High Resolution Display Test select 09 from the Diagnostic Test Menu, press Enter and follow the directions on the screen.
Test Program for Field. Subtest 02 640*480 Mode Display This subtest uses 640*480 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below.
Test Program for Field. Subtest 03 800 * 600 Mode Display This subtest uses 800*600 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 256 gradations of white, red, green, and blue as shown below.
Test Program for Field. Subtest 04 1024* 768 Mode Display This subtest uses 1024*768 video resolution to display a high resolution white frame, 256 letter types (8*16 pixels) and 64 gradations of white, red, green, and blue as shown below.
Test Program for Field. Subtest 05 “H” Pattern Display This subtest uses the 1024*768 Mode to display a high resolution white frame, “H” letters (8*16 pixels fonts), at 128 letters by 48 lines.
Test Program for Field. Subtest 06 Focus Test ( “E” Pattern) This subtest sets the 1024*768 Mode and displays “E” patterns (18*18 dot fonts), at 56 letters *42 lines surrounded by a high resolution white frame.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 55 3.13 Multimedia Test To execute the Multimedia Test select 10 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The Multimedia Test contains four subtests that test the computer's m ultimedia functions.
Test Program for Field. 56 Qosmio X500 Maintenance Manual (960-Q08) 3.14 MEMORY2 Test To execute the Expansion Test select 11 from the Diagnostic Test Menu, press Enter and follow the directions on the screen. The MEMORY2 Test contains four subtests that test the computer's.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 57 Tee test method is the same as Subtest2. However, the data to be used differs. 7FFF7FFF7FFF7FFF8000800080008000 BFFFBFFFBFFFBFFF4000.
Test Program for Field. 58 Qosmio X500 Maintenance Manual (960-Q08) 3.15 Error Codes and Error Status Names The following table lists the error codes and error status names for the Diagnostic Tests.
Test Program for Field. Table 3-2 Error codes and error status names (2/2) Device Name Error Code Error Status Name HDD BB Undefined Error CC Write Fault E0 Status Error F0 No Sense Error ?? Other Err.
Test Program for Field. 60 Qosmio X500 Maintenance Manual (960-Q08) 3.16 Running Test NOTES : 1. You may add or delete subtests using the Running Test Edit Item function, see Section 3.20. 2. Do not forget to insert a work disk in the FDD. If a work disk is not inserted an error will be generated during the Floppy Disk Test.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 61 3.17 DMI INFOEMATION Select 03 from the Diagnostics Menu and press Enter to Check or W rite DMI Information Data: 3.
Test Program for Field. 62 Qosmio X500 Maintenance Manual (960-Q08) b. Wireless LAN ID ( 001E4CXXXXXX ) c. AC Adapter Select [1]65W [2]75W [3]90W [4]120W Select 1 ~ c to keyin new data , select 0 to e.
Test Program for Field. 3.18 Log Utilities This function logs error information generated while a test is in progress and stores the results in RAM (Maximum error log : 500 tim es). This function can store data on a floppy disk. If the power switch is turned off, the erro r inform ation will be lost.
Test Program for Field. 64 Qosmio X500 Maintenance Manual (960-Q08) 2. Error information displayed on the screen can be manipulated with the following number keys: The 1 key scrolls the display to the next page. The 2 key scrolls the display to the previous page.
Test Program for Field. 3.19 System Configuration Select 05 from the Diagnostics Menu and press Enter to display the following system configuration: SYSTEM CONFIGURATION : * - BIOS VER = VX.XX KBC VER = XXXX * - MAC ADDRESS : XXXXXXXXXXXX * - 0 ASYNC ADAPTER * - 1 HDD DRIVE(S):XXXXXXXXXXXXXXXXXXXXXXXXXX FW Rev.
Test Program for Field. 3.20 Running Test Edit Item 3.20.1 Function Description Function description lets you add or delete the subtests used to execute the Running Test. The following screen displays after pressing the Tab key to edit an item in the Running Test.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 67 1. Enter a number or 0 for Loop Count and press Enter . Select a number from 1 to 65535 to define the num ber of times the Running Test executes. Select 0 to run the test continuously until halted by the user.
Test Program for Field. 3.21 Common Tests and Operation 3.21.1 How to operate a wi ndow To input parameters, or open a window use the following keys. key : to move a highlight bar [Enter] key : to select an item at the highlight bar [Esc] key : to close the current window and go back to the previous window 3.
Test Program for Field. Qosmio X500 Maintenance Manual (960-Q08) 69 Pass Count Displays the number of times the test has been executed. Error Count Displays the number of errors which have occurred during the test. Write Data Displays only the test data that has failed to compare during the test while being written during the test.
Test Program for Field. 3.21.4 Test Stop Display If an error occurs during a Subtest and YES is selected for Error Stop, the following message displays: [HALT OPERATION] 1. Test end 2. Continue 3. Retry * Select 1, 2, or 3 The three selections have the following functions: 1: Terminates the test program and exits to the subtest menu.
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8) 4-i Chapter 4 Replacement Procedures.
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8) 4-ii Chapter 4 Contents 4.1 Overview ................................................................................................................... .4 - 1 Safety Precautions ....
Replacement Procedures Qosmio X500 Main tenance Manual (96 0-Q08) 4-iii 4.21 Web Camera module................................................................................................ 4-62 4.22 Speaker Box ......................................
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8) 4-iv Figure 4-13-2 Remove the screws(from bottom side) ...................................................... 4-38 Figure 4-13-3 Remove th e screws(from top side) ....................
Replacement Procedures 4 2 4.1 Overview This chapter describes the procedure for rem oving and replacing the fi eld replaceable units (FRUs) in the PC. It may not be necessary to remove all the F RUs in order to replace one. The chart below provides a guide as to whic h other FRUs must be removed before a particular FRU can be removed.
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8 ) 4-2 Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions w hile working on the computer. DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba.
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8 ) 4-3 Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.
Replacement Procedures Disassembly Procedure Three main types of cable connector are used. Pressure plate connector Spring connector Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cab le out from the connect or.
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8 ) 4-5 Assembly Procedure After the computer has been disassembled and th e part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembling the computer.
Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION : Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall ou t) causing a short circuit or other damage.
Replacement Procedures Qosmio X500 Maint e nance Manual (960- Q0 8 ) 4-7 Screw Notation To make maintenance of the co mputer easier, markings of the kinds of the screws including the types and lengths are i ndicated on the computer body.
Replacement Procedures 4.2 Battery pack Removing the battery pack The following describes the procedure for rem o ving the battery pack (See Figure 4-2-1). CAUTION: Take care not to short circuit the te rminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack.
Replacement Procedures NOTE : Dispose of the used battery pack in a ccordance with the laws and ordinances of your local authority. Installing the battery pack The following describes the procedure for inst alling the battery pack (See Figure 4-2-2).
Replacement Procedures 4.3 PC card Removing a PC card The following describes the procedure for removing a PC card (See Figure 4-3-1). CAUTION: Insert or remove a PC card in accordan ce with any instructions in a PC card manual or the manuals of the co mputer system you are using.
Replacement Procedures 1. Make sure the PC card does not stick out. 2. Insert a PC card and press it until it is secu rely connected. Figure 4-3-2 Insert a PC card Qosmio X500 Maintenance Manual (960-.
Replacement Procedures 4.4 SSD/HDD (Main HDD) Removing a SSD/MAIN HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for re m oving the SSD/main HDD (See Figure 4-4-1 to 4-4-3). CAUTION: Take care not to press on the top or bottom of a SSD/HDD.
Replacement Procedures CAUTION: When a SSD/HDD is installed, they ar e installed in the position as the following figure. Figure 4-4-2 Remove the SSD/MAIN HDD assembly Qosmio X500 Maintenance Manual (.
Replacement Procedures 5. Remove the following screws securing the SSD/HDD holder and remove the SSD/ HDD holder . M3.0 3.0B FLAT BIND screw x4 Figure 4-4-3 Remove SSD/MAIN HDD Qosmio X500 Mai.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-15 Installing SSD/MAIN HDD-H9.5mm / HDD-H12.5 mm The following describes the procedure for installing the main HDD. 1. Install a SSD/HDD to the SSD/HDD holder and secure it with the follow ing screws .
Replacement Procedures 4.5 Optical disk drive NOTE : Do not apply excessive force to the top of an optical disk d rive. Do not touch the shaded portion of the fi gure below, when the drive is removed or installed. Removing an optical disk drive The following describes the procedure for rem o ving an optical disk drive (See Figure 4-5- 1and 4-5-2).
Replacement Procedures Figure 4-5-2 Disassemble the side bracket Installing an opt ical disk drive The following describes the procedure fo r installing an optical disk drive. 1. Attach the ODD bracket to an optical disk drive and secur e it with the following screws .
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-18 4.6 Slot in Optical disk drive NOTE : Do not apply excessive force to the top of an optical disk d rive. Do not touch the shaded portion of the fi gure below, when the drive is removed or installed.
Replacement Procedures Figure 4-6-1 Remove an optical disk drive Figure 4-6-2 Disconnect the Sl ot in ODD from Motherboard Qosmio X500 Maintenance Manual (960-Q08) 4-19.
Replacement Procedures Figure 4-6-3 Disassemble the bracket from slot in ODD Installing an opt ical disk drive The following describes the procedure fo r installing an optical disk drive. 1. Attach the ODD bracket to an optical disk drive and secur e it with the following screws .
Replacement Procedures 4.7 HDD (SECOND HDD) Removing second HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for re moving the second HDD (See Figure 4-7-1 to 4- 7-3). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device.
Replacement Procedures CAUTION: When a HDD is installed, they are inst alled in the position as the following figure. Figure 4-7-2 Remove the SECOND HDD assembly Qosmio X500 Maintenance Manual (960-Q0.
Replacement Procedures 5. Remove the following screws securing the HDD holder and remove the HDD holder . M3.0 3.0B FLAT BIND screw x4 Figure 4-7-3 Remove the screws and HDD holder Qosmio X500.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-24 Installing Second HDD-H9.5mm / HDD-H12.5mm The following describes the procedure for installing a HDD. 1. Install a HDD to the HDD holder and secure it with the fo llo wing screws . M3.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-25 4.8 Memory module CAUTION: The power of the computer must be turned off when you remove a memory module. Remove a memory module with the power on risks damaging the module or the computer itself.
Replacement Procedures Figure 4-8-1 Remove memory slot cover Figure 4-8-2 Remove a memory module Qosmio X500 Maintenance Manual (960-Q08) 4-26.
Replacement Procedures Installing a memory module To install a memory module, confirm that the com puter is in boot mode. Then perform the following procedure (See Figure 4-8-3). 1. Insert a memory module into the connector of the com puter slantwise (term inal side first) and press it to connect firmly.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-28 4.9 Keyboard Removing the keyboard The following describes the procedure for rem oving the keyboard (See Figure 4-9-1). CAUTION: As the keycap may fall out, when handling the keyboard always hold it by the frame and do not touch the keycap.
Replacement Procedures Figure 4-9-1 Remove screws for KB Holder Qosmio X500 Maintenance Manual (960-Q08) 4-29.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-30 Installing the keyboard The following describes the procedure for installing the keyboard. 1. Turn the keyboard upside down and place it on the palm rest as its face do wn. Connect the keyboard flexible cable to the connector on the system board.
Replacement Procedures 4.10 Wireless LAN card Removing a Wireless LAN card The following describes the procedure for re m oving a Wireless LAN card (See Figure 4-10-1 to 4-10-2). 1. Remove the following screw of wireless cover securing wireless LAN card cover and remove it.
Replacement Procedures Figure 4-10-2 Remove a wireless LAN card Qosmio X500 Maintenance Manual (960-Q08) 4-32.
Replacement Procedures Installing a Wireless LAN card The following describes the procedure for installing a W ireless LAN card. 1. Insert a wireless LAN card terminals slantwise into the connector on the com puter and press a wireless LAN card and lock the secure screws.
Replacement Procedures 4.11 Bluetooth module Remove a Bluetooth module The following describes the procedure for re moving a Bluetooth m odule(see Figure4-11-1) 1. Disconnect the Bluetooth cable from motherboard side 2. Remove the following screw from TOP case and remove the Bluetooth bracket 2.
Replacement Procedures 4.12 TV Tuner card Removing a TV Tuner card The following describes the procedure for rem o ving a TV Tuner card (See Figure 4-12-1). 1. Remove the following screw of TOP cover securing a nd rem ove it. And remove screw of TV tuner card 2.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-36 Installing a TV Tuner card The following describes the procedure for installing a TV tuner card. 1. Insert a TV tuner card terminals slantwise in to the connector on the computer and press a TV tuner card and lock the secure screws.
Replacement Procedures 4 4.13 Display assembly Removing the display assembly The following describes the procedure for rem o ving the display assembly (See Figure 4-13-1 to 4-13-5). 1. Close the display and turn the computer upside down. 2. Remove the battery pack (See Figure 4-2-1) 3.
Replacement Procedures M2.5 6.5 FLAT BIND screw x11 M2.5 8.0 FLAT BIND screw x6 M2.5 4.0 FLAT BIND screw x2 M2.5X3.0 FLAT BIND screw x1 M2.5 2.0 FLAT BIND screw x5 Figure 4-13-2 Remove the screws (from bottom side) 6.
Replacement Procedures Figure 4-13-3 Remove the screws (from top side) 8. Disconnect the FFC and cables. 9. Disassembly TOP cover. 10. Pull out the wireless LAN antenna and LCD cables from the guide.
Replacement Procedures Opening the display to 135degree, and remove the hinge screw. ‧ M2.5 6.5 FLAT BIND screw x6 (Locktight) Figure 4-13-5 Remove the hinge screws 11. Pulling out the pole of hinge from the hole of hinge assembly, rem ove the display assembly from the base assembly.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-41 4. Arrange the wireless antenna cables along the guide (front) and secure them with guide . 5. Pass the cables to the back of computer through the slot . 6. Arrange the wireless LAN antenna along the guide and contact with the connector.
Replacement Procedures 4.14 Top Cover assembly Removing the Top cover assembly The following describes the procedure for rem o ving the top cover assembly (See Figure 4- 14-1 to 4-14-3). 1. Turn over the computer. 2. Remove the following screws securing the top cover assembly from the back and bottom of computer.
Replacement Procedures 3. Remove the following screws securing the top cover assembly from the front of computer. Pull up and remove the top cover assembly from the base assembly . M2.5x6.5 Flat BIND screws x7 Figure 4-14-2 Remove the screws (front) and top cover assembly 4.
Replacement Procedures Figure 4-14-3 Disconnect the touch pad flat cable/Fingerprint cable Installing Top Cover assembly The following describes the procedure fo r installing the top cover assem bly. 1. Install the top cover assembly to the base assembly.
Replacement Procedures 4.15 Touch pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-15-1 to 4- 15-3). 1. Peel off the glass tape and disconnect the touch pad flat cable, Fingerprint cable from the connector on the touch pad.
Replacement Procedures Figure 4-15-2 Loose the M2.5x3 screw Figure 4-15-3 Remove the touchpad and touchpad board Qosmio X500 Maintenance Manual (960-Q08) 4-4 6.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 4-4 7 Installing the touch pad The following describes the procedure for installing the touch pad. 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE : Do not reuse the touch pad so that it c an not be used after peeling off from the computer.
Replacement Procedures 4.16 USB Board The following describes for removing the USB board (See Figure 4-16-1). Removing the USB Board 1. Pull out the USB cable, Audio cable, from USB board connector. 2. Loose the below screws and then incline pull out USB board.
Replacement Procedures 4.17 B CAS Board The following describes for removing th e B CAS Board (See Figure 4-17-1). Removing the B CAS Board 1. Pull out the B CAS FFC from USB board connector. 2. Loose the below screws and then incline pull out B CAS board.
Replacement Procedures 4.18 System Board CAUTION: 1. when handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. if replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configu ration”.
Replacement Procedures 2. Disconnect the speaker cable, LCD CABLE, WI RELESS ANTENNA, CRT cable, USB cable, FM CABLE, MDC CA BLE, and TV-F ANTENNA from the connector on the system board. 3. Remove the following screws securing the fan and the system board and remove the system board .
Replacement Procedures Removing RTC battery The following describes the procedure for rem o ving the RTC battery unit (See Figure 4-18-3 to 4-18-4). 1. Pull the away the socket of RTC battery a nd use a clam p to hold RTC battery tightly. Figure 4-18-3 Pull away from the socket of RTC Battery 2.
Replacement Procedures Installing the System Board The following describes the procedur e for installing the system board. 1. Secure the system board with the following screws . M2.5 6.5 screw x3 2. Secure the fan with the following screw s . M2.5 6.
Replacement Procedures 4.19 CPU Removing the CPU heat sink The following describes the procedure for rem o ving the CPU heat sink (See Figure 4-19-1 to 4-19-2). 1. Disconnect the Heat sink cable from the connector on the system board 2. Remove the following screws securing the heat sink holder along 1 to 4.
Replacement Procedures 4. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the counterclockwise with a flat-blade screwdriver. 5. Remove the CPU . Figure 4-19-2 Remove the CPU Installing the CPU The following describes the procedure for installing the CPU (see Figure 4-19-3) 1.
Replacement Procedures Figure 4-19-3 Apply silicon grease 6. Install the CPU heat sink and heat sink holder and secure them with the following screws along 1 to 4.
Replacement Procedures 4.20 LCD unit / FL inverter CAUTION: When replacing a LCD, it is required that SVP parameter is set. Update with the latest EC/KBC as describe d in Appendix H “EC/KBC Rewrite Procedures”.
Replacement Procedures 3. Pull out one insulator and peel off the other one adhered to the inverter. 4. Disconnect the LCD harnesses from the connectors CN1 on the inverter. 5. Disconnect the HV harnesses from the connectors CN2 on the inverter. 6. Remove the FL inverter while peeling off the double-sided tape .
Replacement Procedures 7. Remove the following screws securing the LCD unit. M2.5x4.0 screw x2 M2.5x5.0 screw x8 8. With the bottom edge of the LCD unit on the display cover, lift onl y the top edge of the LCD unit. After peeling off the CONDUTIVE tape , disconnect the LCD harness from the connector on the back of the LCD.
Replacement Procedures 10. Remove the following screws securing the LCD support (LCD unit side) and rem ove the hinge from the LCD unit. M2.0x2.5 screw x8 Figure 4-20-4 Remove the LCD hinge Qosmio.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 61 Installing the LCD unit/FL Inverter The following describes the procedure for installing the LCD unit and FL inverter. Install the LCD supports (LCD unit side) and hi nge to the LCD and secure them with the following screws .
Replacement Procedures 4.21 Web Camera module Removing Web Camera module The following describes the procedure for removing the Web Camera m odule. (See Figure 4-21-1 to 4-21-2). 1. Pull off the connector of Web Camera module. Figure 4-21-1 Remove the connector of Web Camera module 2.
Replacement Procedures Figure 4-21-2 Peel off the glue of Web Camera module Installing Web Camera module The following describes the procedure for installing the W eb Camera module. 1. Pull in the glue of Web Camera Module. 2. Connect the connector of Web Camera module.
Replacement Procedures 4.22 Speaker Box Removing Speaker Box The following describes the procedure for removing Speaker Box. (See Figure 4-22-1 to 4-22-3). 1. Remove the following screws securing Speaker Box. M2.5 2.0 screw x 4 Figure 4-22-1 Removing the securing screws at left side.
Replacement Procedures Figure 4-22-2 Removing the secu ring screws at right side. 2. Removing the Speaker Box. Figure 4-22-3 Removing the Speaker Box. Qosmio X500 Maintenance Manual (960-Q08) 65.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 6 6 Installing Speaker Box The following describes the proced ure for installing Speaker Box.
Replacement Procedures 4.23 Application for Thermal pad and g rease on CPU, North Bridge, and VGA board (see Figure 4-22-1 to 4-22-3) I. For Silvis thermal pad on North Bridge and grease on CPU Figure.
Replacement Procedures Figure 4-23-2 Apply silicon grease for North Bridge 2. Thermal pad and grease used on VGA thermal module. Figure 4-22-3 Thermal pad position Qosmio X500 Maintenance Manual (960-.
Replacement Procedures Qosmio X500 Maintenance Manual (960-Q08) 69 RAW PN TSB PN Vendor Description JXTZ1027010 A000048650 THERMAL PAD VGA V-RAM AD(JXTZ1027,3A) JXTZ1026010 A000048660 THERMAL PAD VGA CHOKE AD(JXTZ1026,3A) XY0GFCM1000 A000018440 THERMAL GREASE GFC-M1 NOTE: Thermal pad is fixed for each one, no need special applicator and can re-use.
A-1 Qosmio X500 Maintenance Manual Maintenance Manual ( 960-Q08) Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1.
Handling the LCD Module 3. If the panel’s surface gets fingerprint or dust, put on gloves and wipe it with static electricity cloth. If it is still d irty, drop some cleaning alcohol on the surf ace and wipe it again If the surface is much more fingerprint or dust, w e recommend a CRT cleaning agent.
Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge.
Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
Handling the LCD Module 10. If you transport the module, do not use pack ing material that c ontains epoxy resin (amine) or silicon glue (alcohol or oxide).
Qosmio X50 0 Maintenance Manual (960- Q08) B-1 Appendix B Appendix B Board Layout B.1 System Board Figure B-1-1 System board layout (front) 0 1 0 2 0 3 0 4 0 5 0 6 1 6 1 0 11 1 2 13 1 8 07 09 14 15 17.
Board Layout B-2 Qosmio X500 Maintenan ce Manual (9 60-Q08) 42 41 29 30 40 39 25 34 32 3 1 43 33 38 8 37 35 Figure B-1-2 System board layout (Back).
Board Layout Qosmio X50 0 Maintenance Manual (960- Q08) B-3 Table B-1-1 System board ICs and connectors NUM Location Function (01) CN6 SPDIF CONN (02) CN10 Audio&USB CONN (03) CN11 LVDS CONN (04) .
Board Layout B-4 Qosmio X500 Maintenan ce Manual (9 60-Q08) (23) CN13 Power/B CONN (24) U2 Audio IC (25) U13 Clock generator (26) U4 Embedded Controller IC (27) U9 LAN IC (28) U27 Card Reader /1394 (2.
Board Layout B.2 Touch Pad Board <Front layout> 04 03 01 02 Figure B-2-1 Touch Pad board layout (Front) Table B-2-2 Touch Pad board connectors NUM Location Function (01) SW1 Mouse Button Left ke.
Board Layout 01 02 Figure B-2-3 Touch P ad board layout (Back) Table B-2-2 Touch Pad board connectors NUM Location Function (01) CN3 TP Board to TP Module CONN (02) CN1 TP Board to M/B CONN B-6 Qosmio.
Board Layout B.3 Finger Print Board <Front layout> 01 Figure B-3-1 Finger Print Board layout (Front) Table B-3-2 Finger Pr int Board connectors Location Function (01) U2 Finger Printer IC Qosmio.
Board Layout <Back layout> 01 B-8 Qosmio X500 Maintenan ce Manual (9 60-Q08) 02 Figure B-3-3 Finger Print Board layout (Back) Table B-3-4 Finger Pr int Board connectors Location Function (01) CN.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 1 Appendix C Pin Assignment CN11 LCD Panel Connectors PIN No. Signal name I/O PIN No. Signal name I/O 1 VIN --- 2 LCDVCC --- 3 VIN --- 4 LCD.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 2 CN24 MMB Connector PIN No. Signal name I/O PIN No. Signal name I/O 1 +3VPCU --- 2 +5VPCU --- 3 KEY_INT I 4 GND --- 5 3ND_MBDATA I/O 6 3ND_MBCLK I/O CN20 Keyboard LED Conn ectors PIN No. Signal name I/O PIN No .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 3 7 MY2 O 8 MY1 O 9 MY0 O 10 MY4 O 11 MY3 O 12 MY5 O 13 MY14 O 14 MY6 O 15 MY7_K O 16 MY3_K O 17 MY7 O 18 MY9 O 19 MY10 O 20 MY11 O 21 MY12 .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 4 PIN No. Signal name I/O PIN No. Signal name I/O 1 +5V_Felica --- 2 USBP4- I/O 3 USBP4+ I/O 4 GND --- 5 NC --- 6 NC --- CN10 Audio&USB Board Connectors PIN No.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 5 1 GND --- 2 USBP9- I 3 USBP9+ I 4 CPUSB# I/O 5 --- --- 6 --- --- 7 NEW SMCLK I 8 NEW SMDATA I/O 9 +NEW_1.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 6 PIN No. Signal n ame I/O PIN No. Signal name I/O 1 RTC_NO2 I 2 GND --- CN2 CRT Connectors PIN No.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 7 1 MBAT+ --- 2 MBAT+ --- 3 ID O 4 B/I --- 5 TEMP_MBAT O 6 MBDATA I/O 7 MBCLK I/O 8 GND --- 9 GND --- 10 GND --- 11 GND --- 12 GND --- 13 GND --- CN15 MINI PCI-E Card WLAN Connecto r s PIN No.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 8 31 PCIE_TXN0 I 32 WL_SMDATA I/O 33 PCIE_TXP0 I 34 GND --- 35 GND --- 36 USBP3-_B I/O 37 GND --- 38 USBP3+_B I/O 39 NC --- 40 NC --- 41 NC --- 42 NC --- 43 GND --- 44 LED_WLAN# --- 45 CL_CLK1_MIN --- 46 LED_WPAN # --- 47 CL DATA1 MIN --- 48 +1.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 9 7 NC I/O 8 NC --- 9 GND --- 10 NC I 11 NC I/O 12 NC --- 13 NC I/O 14 NC I/O 15 GND --- 16 BCIO-P5P I/O 17 BCRST-P3N I/O 18 IVDET-P3P --- 19 BCPWON-P3P I/O 20 NC I/O 21 GND --- 22 RESET# I/O 23 NC I/O 24 +3.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 10 PI N No. Signal name I/O PIN No. Signal name I/O 1 +0.9VSMDDR_VREF_ DIMM --- 2 GND --- 3 GND --- 4 M_B_DQ0 I/O 5 M_B_DQ5 I/O 6 M_ B_DQ1 I.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 11 51 M_B_DQS2 I/O 52 M_B_DM2 I 53 GND --- 54 GND --- 55 M_B_DQ23 I/O 56 M_B_DQ18 I/O 57 M_B_DQ22 I/O 58 M_B_DQ19 I/O 59 GND --- 60 GND --- .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 12 103 +1.8VSUS --- 104 +1.8VSUS --- 105 M_B_A10 I/O 106 M_B_BS#1 I 107 M_B_BS#0 I 108 M_B_RAS# I 109 M_B_WE# I 110 M_CS#2 I 111 +1.8VSUS --- 112 +1.8VSUS 113 M_B_CAS# I 114 M_ODT2 I 115 M_CS#3 I 116 M_B_A13 I/O 117 +1.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 13 155 GND --- 156 GND --- 157 M_B_DQ52 I/O 158 M_B_DQ53 I/O 159 M_B_DQ49 I/O 160 M_B_DQ48 I/O 161 GND --- 162 GND --- 163 NC --- 164 M_CLK_.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 14 PIN No. Signal name I/O PIN No. Signal name I/ O 1 HDMITX2P_ C --- 2 GND --- 3 HDMITX2N_ C --- 4 HDMITX1P_ C --- 5 GND --- 6 HDMITX1N_ C .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 15 CN39 VGA Connectors PIN No. S PI Sign ignal name N No. al name 2 PEG_TXN15 1 E P G_RXN15 4 PEG_TXP15 3 E P G_RXP15 6 GND 5 N G D 8 PEG_TX.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 16 60 GND 59 N G D 62 PEG_TXN5 61 E P G_RXN5 64 PEG_TXP5 63 E P G_RXP5 66 GND 65 N G D 68 PEG_TXN4 67 E P G_RXN4 70 PEG_TXP4 69 E P G_RXP4 7.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 17 AT 114 GND 11 G 3 V A_MBCL K 116 EXT_VGA_RED 11 X N 5 E T_LVDS_BLO 118 GND 11 X P_ ON 7 E T_DIS 120 EXT_VGA_GRN 11 P 9 D _HPD 122 GND 12 .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 18 158 5V 15 7 X 160 5V 15 V 9 3 162 X 16 V 1 3 164 X 16 V 3 3 166 DP_CAD 16 V 5 3 168 CEC 16 V 7 3 170 GND 16 9 X 172 EXT_DPTX3N 17 1 X 174.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 19 9 LAN _ VCC4 --- 10 LAN _ LINKLED# --- 11 LAN _ ACTLED --- 12 LAN _ GND --- C Conn N No. I/O N No. l name I/O N37 USB ecto rs PI Signal name PI Signa 1 GND --- BUSBP6+ --- 2 3 BUS --- USBPWR2 --- BP6- 4 5 GND --- GN --- 6 D 7 GND --- GND --- 8 CN32 2nd SATA HDD Connecto IN No.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 20 CN3 Card R tors PIN No. Sig PIN No. XD C XD _C X SD/MS_CLK_C S MS _C MS_CD#_C MS_DX/SD_D1_C MS_D0/ XD_D2_C MS_D 0_C 24 MS_D1/X _D7_C I/O .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 21 CN46 SATA HDD Connectors IN No. l name I/O IN No. nal name I/O P Signa P Sig 1 GND A_TXP0 --- 2 SAT O 3 SATA_TXN0 O 4 GND --- 5 SATA_RXN0 I 6 SATA_RXP0 I 7 GND --- 8 +3.3VSATA --- 9 +3.3VSATA --- 10 +3.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 22 11 TMPSPR-GND PR-SXP 12 TMPS 13 CLKDWN# 14 ALERT 15 PLTRST# 16 CLKREQ# 17 NC 18 NC 19 +3V_ +3V TMA_VDD 2 0 _ TMA_VDD 21 22 NC NC 23 NC 24 GND 25 GND 26 GND 27 GND 28 GND 29 GND 29 GND 31 GND 3 0 GND CN17 Min Connectors No.
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 23 23 E_RXN5 _S5 PCI O 24 +3V --- 25 D PCIE_RXP5 O 26 GN --- 27 GND --- 28 +1.5V --- 29 _SMCLK GND --- 30 MINI3 I/O 31 PCIE_TXN5 3_SMDATA I .
Pin Assignment Qosmio X50 0 Maintenance Ma nu al (960 -Q08) 24 CN6 SPDIF Connectors PIN No. Sig na l name I/O PIN No. Sig nal name I/O 1 GND --- 2 BOARD_ID2 --- 3 SPK_L- --- 4 SPK_L+ --- 5 SPK_R- --- .
Display codes Qosmio X50 0 Maintenance Ma nu al (960 -Q08) D -1 Appendix. D Appendix D Display Codes D.1 Display Codes Table D-1-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No.
Display codes Qosmio X50 0 Maintenance Manual (960- Q08) D -2 Table D-1-2 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 .
Display codes Qosmio X50 0 Maintenance Ma nu al (960 -Q08) D -3 Table D-1-3 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3.
Display codes Qosmio X50 0 Maintenance Manual (960- Q08) D -4 Table D-1-4 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 1.
Display codes Qosmio X50 0 Maintenance Ma nu al (960 -Q08) D -5 Table D-1-5 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F.
Display codes Qosmio X50 0 Maintenance Manual (960- Q08) D -6 Table D-1-6 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0.
Display codes Qosmio X50 0 Maintenance Ma nu al (960 -Q08) D -7 Table D-1-8 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9.
Display codes Qosmio X50 0 Maintenance Manual (960- Q08) D -8 Table D-1-10 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm on * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.
Appendix E Key Layout 1. United Status (US) K eyboard Figure US keyboard 2. United Status (US) K eyboard (Backlight) Figure US keyboard (Backlight) E-1 - Qosmio X500 Maintenance Manual (960-Q08).
3. United Kingdom (UK) K eyboard Figur e UK keyboard 3. United Kingdom (UK) K eyboard (Backlight) Figur e UK keyboard (Backlight) E-2 - Qosmio X500 Maintenance Manual (960-Q08).
Qosmio X50 0 Maintenance Ma nu al (960 -Q08) F-1 Appendix F Appendix F Wiring Diagrams F.1 RGB Monitor ID Wraparound connector round connector (15PIN to 15PIN) F.
Wiring Diagrams Qosmio X50 0 Maintenance Ma nu al (960 -Q08) F -2.
デバイスToshiba X500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Toshiba X500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはToshiba X500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Toshiba X500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Toshiba X500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Toshiba X500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はToshiba X500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Toshiba X500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちToshiba X500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。