TP-Linkメーカー54Mbps Wireless Access Point TL-WA501Gの使用説明書/サービス説明書
ページ先へ移動 of 45
User Guide TL-W A501G 54Mbps Wireless Access Point TM 2x to 3x eXtended Range 2.4GHz 802.1 1g/b Rev:2.0.
COPYRIGHT & TRADEMARKS S pecifications are subject to change without notice. is a registered trademark of TP-LINK T echnologies Co., Lt d. Other brands and product names are trademarks or registered trademarks of their respective holders.
FCC STATEMENT This equipment has been tested and found to comp ly with the limits for a class B digital device, pursuant to part 15 of the FCC Rule s. These limits are designed to provide reasonable protection against harmful inte rference in a residential installation.
¾ EN 60950-1: 2001 ¾ EN 55022: 1998 + A1: 2000 + A2: 2003 ¾ EN61000-3-2:2001 ¾ EN61000-3-3:2001 ¾ EN 55024: 1998 +A1: 2001 + A2: 2003 European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835G Hz; In France, the equipment must be restricted to the 2.
Package contents .............................................................................................................. 1 Chapter 1: About this Guide .............................................................................................
TL-W A501G 54M Wireless Access Point User Guide Package content s The following contents should be found in your box: ¾ One TL-W A501G 54Mbps Wireless Access Point ¾ One AC power Adapter for TL-WA50.
TL-W A501G 54M Wireless Access Point User Guide Chapter 1: About this Guide Thank you for choosing the TL-W A501G 54Mbps Wireless Access Point. This AP provides connectivity between Ethernet wired networks and radio-equipped wireless devices.
TL-W A501G 54M Wireless Access Point User Guide Chapter 2: Introduction 2.1 Overview of the AP The TL-WA501G 54Mbps Wireless Access Point is the basic bu ilding block of a wireless LAN infrastructure.
TL-W A501G 54M Wireless Access Point User Guide 2.3 Panel Layout 2.3.1 The Front Panel Viewed from left to right, as shown in fi gure 2-1, the front panel of the TL-W A501G consists of four LEDs, whic h is designed to indicate connec tions. T able 2-1 describes the LEDs on the front panel of the AP .
TL-W A501G 54M Wireless Access Point User Guide Figure 2-2: Rear Panel sketch - 5 -.
TL-W A501G 54M Wireless Access Point User Guide Chapter 3: Connecting the AP 3.1 System Requirement s ¾ Broadband Internet Access Service (DSL/Cable/Et hernet) ¾ One DSL/Cable Modem t hat has an RJ45 connector ¾ A Ethernet broadband ro uter ¾ TCP/IP protocol must be inst alled on each PC ¾ Web browser , such as Microsoft Internet Explorer 5.
TL-W A501G 54M Wireless Access Point User Guide Figure 3-1 The Exampl e of Infrastructure Network Incorporating the TL-W A501G - 7 -.
TL-W A501G 54M Wireless Access Point User Guide Chapter 4: TCP/IP Configuration After connecting the TL-W A501G AP into your network, you should configure it. The default IP address of th e TL-WA501G 54Mbp s Wireless Access Point is 192.168.1.1, and the default Subnet Mask is 255.
TL-W A501G 54M Wireless Access Point User Guide Figure 4-2: Failed result of Ping command If the result displayed is similar to that shown in figure 4-2, it means that your PC has not connected to the AP .
TL-W A501G 54M Wireless Access Point User Guide Chapter 5: Configuring the AP This chapter describes eac h web page's key functions. 5.1 login With a Web-based (Internet Explorer or Netscape ® Navigator) utility , the TL-W A501G 54Mbps Wireless Access Point is easy to configure and manage.
TL-W A501G 54M Wireless Access Point User Guide read-only . 1. Network This field displays the current settings or information for the Network, including the MAC address, IP address and Subnet Mask.
TL-W A501G 54M Wireless Access Point User Guide ¾ MAC Address - the physical address of the AP , as seen from the LAN. The value can't be changed. ¾ IP Address - Enter the IP address of your AP in dotted-decimal notation (factory default: 192.168.
TL-W A501G 54M Wireless Access Point User Guide Figure 5-6a: Wireless Settings ¾ Channel - This field determines which operati ng frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
TL-W A501G 54M Wireless Access Point User Guide ¾ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the AP can be used. If your country or region is not listed, please contact your local government agency for assistance.
TL-W A501G 54M Wireless Access Point User Guide ¾ Disable Wireless - The wireless of this AP can be enabled or disabled to allow wireless stations access. If disabled, wire less stations will not be able to acce ss the AP. AP provides five operational modes: Access Point, Client, Repeater, Bridge (point to point), Bridge (point to Multi-point).
TL-W A501G 54M Wireless Access Point User Guide Figure 5-8: wireless repeating 2. Verify the wireless security parameters for all access points, if any.
TL-W A501G 54M Wireless Access Point User Guide • Both use the same Channel, and security settings if security is in use. • Verify connectivity across the LAN 1 and LAN 2.
TL-W A501G 54M Wireless Access Point User Guide share files and printers with any other PCs or servers connected to any of the three LAN segments. • Wireless stations will not be able to connec t to the TL-WA501G Access Points in the illustration above.
TL-W A501G 54M Wireless Access Point User Guide Figure 5- 12: Wireless Securities ¾ Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the AP wit hout encryption. It is recommended strongly that y ou choose one of following opt ions to enable security.
TL-W A501G 54M Wireless Access Point User Guide 2) For 128-bit encr yption - You can enter 26 hexadec imal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters.
TL-W A501G 54M Wireless Access Point User Guide Figure 5-13: Wireless MAC address Filtering The Wireless MAC Address Filtering feature al lows you to control wireless stations accessing the AP, which depend on the station's MAC addresses. ¾ MAC Address - The wireless st ation's MAC address that you want to access.
TL-W A501G 54M Wireless Access Point User Guide 2. Enter a simple description of the wireless station in the Description field. For example: Wireless station A. 3. Privilege - Selects the privileges for this entry, one of Allo w / Deny / 64-bit / 128-bit / 152-bit .
TL-W A501G 54M Wireless Access Point User Guide Key field and select Enabled in the Status pull-down list. Click the Save and the Return button. The filtering rules that configured s hould be similar .
TL-W A501G 54M Wireless Access Point User Guide 5.5 DHCP Figure 5-17: the DHCP menu There are three submenus under the DH CP menu (shown in figure 5-17): DHC P Settings , DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding functi on.
TL-W A501G 54M Wireless Access Point User Guide ¾ Primary DNS - (Optional.) Input the DNS IP addre ss provided by your ISP. Or consult your ISP. ¾ Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers.
TL-W A501G 54M Wireless Access Point User Guide Figure 5- 20: Address Reservation ¾ MAC Address - The MAC address of the PC of which you want to reserve IP address. ¾ Assigned IP Address - The IP address of the AP reserved. To Reserve IP addresses: 1.
TL-W A501G 54M Wireless Access Point User Guide Figure5-21: AP Wireless Advanced Settings ¾ Disable short preamble - Disable short preamble and use long preamble only.
TL-W A501G 54M Wireless Access Point User Guide Note: When you upgrade the AP's firmware, you may lose it s configuration settings, so make sure you write down the AP settings before y ou upgrade it s firmware. To upgrade the AP's firmware, follow these instructions: 1.
TL-W A501G 54M Wireless Access Point User Guide Figure 5-25: Reboot the AP Click the Reboot button to reboot the AP. Some settings of the AP will take effe ct only after rebooting, which include: • Change LAN IP Address. (Sys tem will reboot automatically) • MAC Clone (system will reboot automatically) • DHCP service function.
TL-W A501G 54M Wireless Access Point User Guide Figure 5-27: System Log The AP can keep logs of all traffic. You can query the logs to find what happened to the AP. Click the Refresh button to refresh the logs. Click the Clear Log button to clear all the logs.
TL-W A501G 54M Wireless Access Point User Guide Appendix A: F AQ 1. No lights are lit on the access point. It takes a few seconds for the power indicato r to light up. Wait a minute and check the power light status on the access point. If the access point has no power.
TL-W A501G 54M Wireless Access Point User Guide Appendix B: Configuring the PCs In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows 95/98. First make sure your Ethernet Adapter is working, refer to the adapter ’s manual if needed.
TL-W A501G 54M Wireless Access Point User Guide Figure B-3: Configuration tab 3) Click on Properties . The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 4) Now you have two ways to configure the TCP/IP protocol below: • Assigned by DHCP Sever a.
TL-W A501G 54M Wireless Access Point User Guide Figure B-5: Gateway tab c. Choose Disable DNS on the DNS c onfiguration tab, as shown in the following figure: Figure B-6: DNS Configuration tab • Setting IP address manually a. Select S pecify an IP address on IP Address t ab, as shown in the followin g figure.
TL-W A501G 54M Wireless Access Point User Guide Figure B-7: IP Address tab b. T ype the AP’s LAN IP address (the default IP is 192.168.1.1) into the Ne w gateway fiel d on the Gateway tab, and click on the Add button, as shown in the figure: Figure B-8: Gateway tab c.
TL-W A501G 54M Wireless Access Point User Guide click Add button . Shown below: Figure B-9: DNS Configuration tab Now , all the configurations are finished , it will take effect af ter reboot.
TL-W A501G 54M Wireless Access Point User Guide Appendix C: Specifications General S tandards IEEE 802.3, 802.3u, 802.1 1b and 802.1 1g Protocols TCP/IP , DHCP Ports One 10/100M Auto-Negotiati on LAN .
TL-W A501G 54M Wireless Access Point User Guide Appendix D: Glossary ¾ 2x to 3x eXtended Range TM WLAN Transmission Technology - The WLAN device with 2x to 3x eXtended Range TM WLAN transmission technol ogy make its sensitivity up to 105 dBm, which gives users the ability to have robust, longer-range wireless connections.
TL-W A501G 54M Wireless Access Point User Guide ¾ WEP ( W ired E quivalent P rivacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. ¾ Wi-Fi - A trade name for the 802.
TL-W A501G 54M Wireless Access Point User Guide Appendix E: Cont act Information For help with the installation or operation of the TP-LINK TL-WA501G 54Mbp s Wireless Access Point, please contact us. E-mail: support@tp-link.com Website: http://www.tp-link.
デバイスTP-Link 54Mbps Wireless Access Point TL-WA501Gの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TP-Link 54Mbps Wireless Access Point TL-WA501Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTP-Link 54Mbps Wireless Access Point TL-WA501Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TP-Link 54Mbps Wireless Access Point TL-WA501Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TP-Link 54Mbps Wireless Access Point TL-WA501Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TP-Link 54Mbps Wireless Access Point TL-WA501Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTP-Link 54Mbps Wireless Access Point TL-WA501Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TP-Link 54Mbps Wireless Access Point TL-WA501Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTP-Link 54Mbps Wireless Access Point TL-WA501Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
