TP-LinkメーカーTD-8816Bの使用説明書/サービス説明書
ページ先へ移動 of 54
TD-8816B ADSL2/2+ Ethernet Router Rev: 1.0.1 1910010017.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trade marks or registered trademarks of t heir respective holders.
FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limit s are designed to pro-vide reasonable protection against harmful interference in a residential installation.
Package contents The following contents should be found in your package: ¾ One TD-8816B ADSL2/2+ Ethernet Router ¾ One AC power Adapter for TD-8816B ADSL2/2+ Ethernet Router ¾ Quick Installation Gu.
CONTENTS Chapter 1. Introduc tion ........................................................................................ 1 1.1 Product Overview ...................................................................................................... 1 1.
4.6.4 System Restart ............................................................................................................... 46 4.6.5 Diagnostic ..................................................................................................
TD-8816B ADSL2/2+ Ethernet Modem User Guide 1 Chapter 1. Introduction 1.1 Product Overview Thank you for choosing the TD-8816B ADSL2/2+ Ethernet Modem . The device is designed to provide a simple and cost-effective ADSL Inte rnet connection for a pr ivate Ethernet network.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 2 ¾ Supports Multiple PVC (Per manent Virtual Circuit). ¾ Built-in DHCP server. ¾ Built-in firewall, supports IP/MAC filter, Application filter and URL filter. ¾ Supports Virtual Server, DMZ host and IP Address Mapping.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 3 Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locates on the front panel, they indicate the device’s working st atus.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 4 devices. ¾ LINE: Through the port, you can connec t the Router with the telephone. 2.3 Inst allation Environment ¾ The Product should not be locat ed where it will be exposed to moisture or excessive heat.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 5 Figure 2-3.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 6 Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD- 8816B or connect your adapter to a Hub/Switch which has connected to the Router , you need to configure your PC’s IP address.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 7 Figure 3-2 Step 3: Select General tab, highlight Internet Protoc ol (TCP/IP), and then click the Properties button.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 8 Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK . Figure 3-4 ) Note: You can c onfigure the PC to get an IP address aut omatically, select “Obtain an IP address automatically” and “Obtain DNS server addre ss automatically” in the screen above.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 9 If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 10 Step 1: Select the Quick Start tab, then click RUN WIZARD , and you will see the next screen. Click the NEXT button.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 11 Figure 3-1 1 Step 5: Click NEXT to finish the Quick Start. Figure 3-12.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 12 Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 13 Figure 4-2 ) Note: Click the other submenus System Log or Statistics in Figure 4-2, you will be able to view the system log and traffic statistics about the Route r. 4.2 Quick S t art Please refer to " 3.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 14 4.3.1 Internet Choose “ Interface Setup → Internet ” menu, you can conf igure the parameters for WAN ports in the next screen (shown in Figure 4-4). Figure 4-4 ¾ ATM VC: ATM settings are used to connect to your ISP.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 15 • Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7. • Status: If you want to use a designed VC, you should activate it. • VPI: Identifies the virtual path bet ween endpoints in an ATM ne twork.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 16 for WAN interface, including RIP1 , RIP2-B and RIP2-M . RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. • Direction: Select this option to s pecify the RIP direction.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 17 Figure 4-7 ¾ Username: Enter your username for your PPPoE/PPPoA connection. ¾ Password: Enter your password for your PPPoE/PPPoA connection. ¾ Encapsulation: For both PPPoE/PPPoA connection, y ou need to specify the type of Multiplexing, either LLC or VC Mux.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 18 4. Bridge Mode If you select this type of connection, the modem can be configured to ac t as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two s egments of the same physical LAN.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 19 needed. The LAN IP address is private to y our internal networ k and cannot be seen on the Internet. • IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default val ue is 192.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 20 • IP Pool Count: The max user pool size. • Lease Time: The length of time for the IP lease. After the dynamic IP a ddress has expired, the user will be aut omatically assigned a new dynam ic IP address.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 21 4.4 Advanced Setup Choose “ Advanced Setup ”, you can see the next submenus: Figure 4-12 Click any of them, and you will be able to configure the corre sponding function. 4.4.1 Firewall Choose “ Advanced Setup → Firew all ” menu, and you will see the next screen (shown in Figure 4-13).
TD-8816B ADSL2/2+ Ethernet Modem User Guide 22 Figure 4-14 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-15). Figure 4-15 ¾ Destination IP Address: This parameter spec ifies the IP network address of the final destination.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 23 Figure 4-16 ¾ Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. ¾ NAT Status: This field shows the current statu s of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-4) to activate the function.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 24 The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to t he outside world even though NAT makes your whole inside network appear as a single machine to the outside world.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 25 4.4.3.3. IP Address Mapping Choose “ Advanced Setup → NAT → IP Address Mapping ” in Figure 4-16, you can con figure the Address Mapping Rule in the next screen. The IP Address Mapping is for those VCs that configured with multiple IPs.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 26 Click the Back button to return to the previous screen. Click the CANCEL button to cancel the configur ation which is made just now. 4.4.4 QoS Choose “ Advanced Setup → QoS ”, you can configure the QoS in the next screen.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 27 DiffServ). ¾ Summary: Click the button to view t he configurations of QoS. ¾ Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 28 can communicate as if they were attached to t he same wire, when in fact they ar e located on a number of different LAN segm ents. Because VLANs are based on lo gical instead of physical connections, it is very flexible for user/ host management, bandwidth allocation and r esource optimization.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 29 2. Define VLAN Group Click Define VLAN Group in Figure 4-21, you can define VLAN groups in the next screen (shown in Figure 4-2 3). Figure 4-23 ¾ VLAN Index: Select the VLAN index for this VC. You can specify 8 gr oups in maximum.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 30 Figure 4-24 ¾ ADSL Mode: Select the ADSL operation mode wh ich your ADSL connection uses. ¾ ADSL Type: Select the ADSL operation type wh ich your ADSL connection uses.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 31 Figure 4-26 ¾ ACL: If Activated , the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated , all IP addresses can access to the Router. ¾ ACL Rule Index: Select the ACL rule index for the entry.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 32 Figure 4-27 ¾ Filter Type Selection: Select the fil ter type fo r the next configuration. ¾ IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 33 allowed by setting up filters. ¾ IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. ) Note: You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Inde x together to appoint the address (shown in the Filter List) for the IP Filter rule.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 34 ) Note: If you want to make the rule take ef fect, please select Ye s to active the rule. Step 3: Enter the “Source IP Address”, “Destinat ion IP Address”, “Subnet Mask” and “Port Number” in the corresponding field.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 35 Figure 4-28 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active: Select “Yes” to make t he rule to take effect.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 36 select the Interface “PVC0”, and select t he Direction “Outgoing” for the first rule. ) Note: If you want to make the rule take ef fect, please select Ye s to active the rule. Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 37 Figure 4-29 ¾ Filter Type Selection: Select the Application Filter for the next configuration. ¾ Application Filter: Activate or deactivate the function. ¾ ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Den y for these applications.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 38 Figure 4-30 ¾ Filter Type Selection: Select the URL Filter fo r the next configuration. ¾ Active: Select “Yes” to make t he rule to take effect. ¾ URL Index: Select the index for the URL Filter entry.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 39 Management Protocol (SNMP) is used for exc hanging information between network devices. Figure 4-31 ¾ Get Community: Select to set the password for the incoming Get and Get next reques ts from the management station.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 40 4.5.5 DDNS Choose “ Access Management → DDNS ”, you ca n configure the DDNS function in the screen (shown in Figure 4-33). The router offers a Dynamic Domain Name System ( DDNS ) feature. The feat ure lets you use a static host name with a dynamic IP address.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 41 Figure 4-34 ¾ CWMP: Select activate the CWMP function. ¾ URL: Enter the website of ACS which is provided by your ISP. ¾ User Name/Passwo rd: Enter the User Name and passw ord to login the ACS server. ¾ Path: Enter the path that connects to the ACS server.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 42 (shown in Figure 4-36). Figure 4-36 ) Note: 1) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 43 Figure 4-37 ) Note: The ADSL Router built-in some NTP Servers, when the Router connects to the In ternet, the Router will get the system time automatically from the NTP Serv er .
TD-8816B ADSL2/2+ Ethernet Modem User Guide 44 Figure 4-39 4.6.3 Firmware Choose “ Maintenance → Firmware ”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-40). Make sure the firmware or ro mfile you want to use is on the local har d drive of the computer.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 45 the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version ha s a new feature that you want to use.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 46 Step 1: Click the Browse button to locate the update file for the de vice, or enter the exact path in “New Romfile Location” field.
TD-8816B ADSL2/2+ Ethernet Modem User Guide 47 Figure 4-45 ) Note: Click the tab, and you will be able to get the corresponding information..
TD-8816B ADSL2/2+ Ethernet Modem User Guide 48 Appendix A: Specification General Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G. 992.2, ITU G.
デバイスTP-Link TD-8816Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TP-Link TD-8816Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTP-Link TD-8816Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TP-Link TD-8816Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TP-Link TD-8816Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TP-Link TD-8816Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTP-Link TD-8816Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TP-Link TD-8816Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTP-Link TD-8816Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
