TriaxメーカーTSR 1000の使用説明書/サービス説明書
ページ先へ移動 of 42
___________________ __________________ __________________ ________ TRIAX TSR 1000 ___________________ __________________ __________________ _________ Digit al Satellite Receiver FT A User Guide.
SAFETY PRECAUTION CAUTION: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to "dangerous voltage" and to prevent from a risk of electric shock. Wa r n i n g : T o reduce the risk of electric shock, don't open the cabinet.
Locating: Slots a nd openings in the cabinet are provided for ventilation to protect it from overheating. Do not bl ock these ope nings or allow them to be blocked by placing the STB on a be d, sofa or other similar surface, nor should it be placed over a radiator or heat regi ster .
Contents 1 CONTENTS 1. Remote Control & Panel Description ....................................................... 3 1.1 Front Panel Description ........................................................................... 3 1.2 Rear Panel Description .
Contents 2 3.5 Delete All ............................................................................................... 17 3.6 Restore channel list and se ttings............................................................. 17 3.7 Save channel list and se ttings .
Remote Control & Panel Des cription 3 1. Remote Control & Panel Description 1.1 Front Panel Description 1. POWER: Is used to switch between the working mode and the st andby mode. 2. Display (4-Digit/7-Segment): Displays the received channel num ber while operating and time while in stan dby mode.
Remote Control & Panel Des cription 4 1.2 Rear Panel Description 1. IF OUT: Satellite output for cascading to other devices Note: The operation of anothe r receiver at the same time is only possible with limited channel selection. 2. IF IN : Satellite input.
Remote Control & Panel Des cription 5 1.3 Remote Control Description.
Basic Operations 6 2. Basic Operations 2.1 Switch on STB Switch the [Device’s Main Power] switch on. you will set Language, First Audio, Se cond Audio, LNB Power , Antenna Setup and Multi Search.
Basic Operations 7 2.5 Channel Number In TV/radio mode you can enter the chann el number directly wit h your remote control unit and confirm the number wit h the OK button to change to the desired channel. 2.6 Mute 1. Press the [Mute] button to mute t he sound.
Basic Operations 8 2.10 EDIT In TV mode, press the [EDIT] button to open the “TV Channel Li st” window . 2.1 1 Audio T rack / Mode 1. In TV mode, press the [Audio] button to open the audio mode window . 2. Select the item you want to adjust with [Channel Up/Down] and change the value with [V olume Up/Down].
Basic Operations 9 2. The [Red] button opens the det ailed schedule of the marked channel. Y ou can select an event with [Channel Up/Down] and display the event’s detailed description with [O K]. 3. Press the [Green] button in the EPG menu to display the det ailed information of the actual event in the selected channel.
Basic Operations 10 3. Press [Y ellow] button to open the SA T list. After selecting a satellite the channel list will be red uced to the channels of this satellite. 4. Press [F A V] button to open F A V list. After selectin g a favorite group the channel list will be red uced to the channels of this group.
Basic Operations 11 2.19 SUB SUB(Subtitle): In “OSD Setting menu, use [V olume Up/Down] to select “On” o r “Off”. If the current channel has subtitl e information, it will be displayed if this function is “On”. If this function is “Off” subtitles won’t be displayed.
Menu Operations 12 3. Channel Press [Menu] in the TV/radio mode to enter the main menu. 1. Press [Channel Up/Down] to select the channel item. 2. Press [OK] to enter the selected item.
Menu Operations 13 3.1.1 Favorite 1. Press [F A V] to open the favorite window . 2. Y ou can select between 8 favorite groups with [Channel Up/Down]. Press [OK] to assign the channel to a favorite group, press [EXIT] to exit favorite group. 3. Press [OK] again to remove the channel from the marked favorite group.
Menu Operations 14 ¾ FT A: Sort channel by free and scrambled seq uence. Free channels will be listed first and scrambled chann els behind in the channel list. ¾ Lock: Unlocked channels are listed first end locked cha nnels at the end. 3.1.4 TV Channel List Edit After pressing the [Y ellow] button a window for entering the password will open.
Menu Operations 15 1. Selecting the name item with [OK] will display a button pad to sh ow you how to edit the channel name. 2. On the “V ideo PID”, “Audio PID” and “PCR PID” items you can input numbers to modify the item’s value.
Menu Operations 16 3.2 Radio Channel List Basically the operation of “Radio Chann el List” is same as “TV Channel List”, except that in the small channel windo w the radio Logo will be di splayed. 3.3 Channel Setup When you enter the “Channel Setup” menu you will see a screen like besid e: 1.
Menu Operations 17 3.4 Fa vorite channel list name When you enter “Favorite channel list name” menu with 8 favorite group will be displayed. Press [Red] or [OK] key on the RCU to rename favorite group with the [Number] buttons. After modification select “Save” and press [OK] to save the favorite group name and leave the edit mo de.
Menu Operations 18 3.7 Save channel list and settings T o save channel list and settings. 1. Enter the password. The default password is “0000”. 2. After entering the pa ssword correct a safety question will show up where you have to confirm first.
Menu Operations 19 4. Installation After selectin g the installation menu you can see the window like b eside. In “Installation” menu; 1. Press [Channel Up/Down] to select menu items among Antenna Setup, Single Search, Multi Search, TP Scan, Satellite List, TP List and Satellite Guide.
Menu Operations 20 2Cascades Port1 / 2Cascades Port2 / 2Cascades Port3 / 2Cascade s Port4 / 2Cascades Port5 / 2Cas cades Port6 / 2Cas cades Port7 / 2Cascades Port8 / 2Ca scades Port9 / 2Cascades Port10 / 2Cascades Port1 1 / 2Cascades Port12 / 2Cas cades Port 13 / 2Casc ades Port1 4 / 2Cascades Port15 / 2Ca scades Port16.
Menu Operations 21 4.3 Multi Search When you enter the “Multi Search” men u a window like the one besid e will open. 1. On “Satellite” item press [OK] to open the satellite list. Then press [Channel Up/Down] to move the highlight and press [OK] to mark/unmark an d [MENU] to finish the selection.
Menu Operations 22 ¾ When you press [Gree n] a safety question will be displayed for confirmation to delete the current tr ansponder or n ot. If you select “Y es”, the current transponder will be deleted and the tot al number of transponders will be reduced.
Menu Operations 23 2. Press [Green] button to open the “Add satellite” window . 3. After pressing [Y ellow] button you will be asked “Are you sure to delete?”. Select “Y es” to delete the marked satellite. Select “No” to cancel the operation.
Menu Operations 24 3. Press [Green] button to open the “Add TP” menu. Here you can add a ne w TP and setu p its p arameters. 4. Press [Y ellow] button will open a dialog box asking you to confirm the deletion of the current TP . If you select “Y es” all the related channels will be deleted.
Menu Operations 25 1. Use the [Number] buttons to input the values of “Local Longitude”, “Local Latitude” and “Satellite Longitude”. 2. Press [V olume Up/Down] to switch east or west in “Local Longitude” and “Satellite Longitude” or to switch north or south in “Local Latitude”.
Menu Operations 26 5. System Setup When you open the “Syste m Setup” menu a window like the one beside will be opened. In “System Setup” menu: 1. Press [Channel Up/Down] to select menu items among Language, TV System, T ime & T imer setting, OSD Setting, Parental Lock, LNB Powe r and RCU position switch.
Menu Operations 27 5.2 TV System When you enter the “TV System” menu you will see the screen like below: 1. Display Mode is used to switch the display mode. Y ou can select from Auto / P AL / P AL-N / P AL-M / NTSC3.58. Press [V olume Up/Down] to switch the desired mode.
Menu Operations 28 ¾ NOTE: If the current channel provides the correct time information, you will see the current time after you entered “T ime” menu. If the channel doesn’t provide time information, you have to input the date and time information manually .
Menu Operations 29 ¾ When you select “Message”(remi nding me ssage) option in “T imer Service” then you can enter additional dat a: ♦ Wakeu p Message: Press [V olume Up/Down] to select the category of the reminding message from Birthday , Anniversary and General.
Menu Operations 30 5.5 Parent al Lock Y ou can set a password for anyone who wishes to operate the “Installatio n” menu. Y ou can also set the password to lock channels. Below you find how to set and change the p assword. 1. On “Parental Lock” press [ OK] to open a dialogue box and input the password.
Menu Operations 31 5.7 RCU position switch 1. This item can select the switch co ntroller’s position. The position number you choose in this menu must be same as the swit ch controller’s setup, or the switch controller can n ot work correctly . 2.
Menu Operations 32 6. T ools When you enter to “T ools” menu, you will see a screen like beside: In “T ools” menu: 1. Press [Channel Up/Down] to select the wanted item among Information, Quick Setup, Game, Factory Default, Software Upgrade and Sat coDX Auto Programming.
Menu Operations 33 Basic operation st atemen t: 1. Te t r i s ¾ Mark “Setup” and press [V olume Up/Down] to select the level (speed). ¾ Mark “S tart” and press [ OK] to start the game.
Menu Operations 34 ♦ Press [V olume Up/Down / Channel Up/Down] to position the round mark. ♦ Press [OK] to set your stone. ♦ Press [MENU] to quit the g ame and return to the game menu. 6.4 Factory Default When you press [OK] on the “Factory Default” item: 1.
Menu Operations 35 Up date Sof tware(receiver to receiv er) 1. Connect master and slave receiv ers with twisted RS-2 32C cable. 2. Power on the master receiv er and make it in standby mode input number key . 3. T urn on slave receiver to begin update.
Menu Operations 36 b) RS232 CABLE LA YOUT # CONNECT TO P .C # CONNECT TO SVR c) Among wires from no.1 to 9 connect wi re no.2 and 3 crossed to both sides, and then connect the GROU ND (GND) of terminal on P .
Menu Operations 37 6.6 SatcoDX Auto Programming This function is using the t ables of the SatcoDX website s to update your channel and satellite list s. Y ou need a special application which i s available on the CD-ROM of the T ele-Satellite magazine.
T echnical specification 38 7. T echnical Specification VIDEO Decoding MPEG-2 & MEPG-1 compatible B i t r a t e M a x 1 5 M b p s O u t p u t A U T O / P A L / N T S C Aspect ratio 4:3, 16:9, Auto.
T echnical specification 39 MISCELLANEOUS Supply voltage 100~240V AC 50/60Hz Power consumption 30 watts max Operation temperature +5 ° C to +40 ° C S torage temperature -20 ° C to +70 ° C Dimensio.
デバイスTriax TSR 1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Triax TSR 1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTriax TSR 1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Triax TSR 1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Triax TSR 1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Triax TSR 1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTriax TSR 1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Triax TSR 1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTriax TSR 1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。