Tripp Liteメーカー93-2007 (200106010)の使用説明書/サービス説明書
ページ先へ移動 of 22
Owner’ s Man ual 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 • www .tripplite.com Intr oduction 2 Impor tant Safety Instructions 4 Configuration & Connection 5 Features 11 Maintenance and Service 14 PowerV erter ® is a registered trademark of T ripp Lite.
2 Intr oduction Congratulations! Y ou’ ve purchased the most advanced, feature-rich integrated in verter and battery charger on the market. Y our APS pro vides your equipment with utility-supplied A.
3-Stage Battery Charger Y our APS rechar ges your battery faster than con ventional char gers because its three-stage charger prof ile (Bulk, Absorption and Float) are optimized, regardless of the type of battery you use (W et or Gel).
4 Impor tant Safety Instructions SA VE THESE INSTRUCTIONS This manual contains important instructions and warnings that should be f ollowed during the installation, operation and storage of all T ripp Lite APS Systems. APS Location W arnings • Install your APS indoors, away from excess moisture or heat, dust or direct sunlight.
5 Configuration DIP SWITCH GROUP A (All models) BA TTER Y TYPE / VOL T AGE POINT Using a small tool, set the 4 “Battery T ype / V oltage Point” Configuration DIP Switches, Group A (located on the front panel of your APS; see Diagram 1, p.
6 DIP SWITCH GROUP B (A vailable on Select Models) LOAD SHARING/EQ U ALIZE BA TTER Y CHARGE Using a small tool, set the “Load Sharing” Configuration DIP Switches, #1 and #2 of Group B (located on the front panel of your APS; see Diagram 1, p. 36).
7 • Equaliz e Battery Charge (DIP Switch #3, Group B) This DIP Switch is momentarily engaged to begin the process of equalizing the internal resistance of your battery’ s cells.
8 Mounting (Optional) (See Diagram 2, p . 36) Battery Selection Select a battery or system of batteries that will provide your APS with proper DC voltage and an adequate amp hour capacity .* Select ‘Deep-Cycle’ batteries to enjo y optimum performance from your APS.
9 Battery Connection 1. Connect your APS’ s positiv e DC T erminal directly to a fuse. T ripp Lite recommends that you install a recognized component fuse block and fuse within 18 inches of the battery . The fuse's rating must equal or exceed the Minimum DC Fuse Rating listed in your APS model’ s specifications on pages 16 or 17.
10 APS systems must be connected to a grounded, permanent wiring system. For most installations, the negati ve battery conductor must be bonded to the grounding system at one (and only one) point in the system. All installations must comply with national and local codes and ordinances.
11 A C Connection continued Simply plug your equipment into the unit’ s A C receptacles. If adapters must be used, choose adapters that provide a connection to ground. • Switch to “ A UTO/REMO TE” when you are using connected equipment. AD V ANT AGE: Uninterruptible power supply .
12 4. “LINE” (All models): This green light will turn continuously ON whene v er connected equipment is receiving utility-supplied A C power and your APS is set to “ A UTO/REMO TE”, meaning that it will provide battery backup if utility po wer fails.
13 9. DC Input T e rminals (All models): The terminals’ lug scre ws secure the wires leading from your external battery or battery system. Y our battery or battery system must provide your APS with proper DC voltage and your equipment with an adequate amp hour capacity .
14 Limited W arranty Maintenance & Service Y our APS model requires no maintenance b ut should be kept dry at all times. Periodically check all cable connections both at the unit and at the battery .
15 T r y these remedies for common APS problems bef ore calling f or help. Call T ripp Lite Customer Ser vice at (773) 869-1234 before returning your APS f or service. SYMPT OM PROBLEMS CORRECTIONS APS does not provide APS not properly connected to Connect APS to utility power .
16 Specifications (Corded Models) CORDED MODELS: APSINT1012 Weight: 11.9 Kg INVERTER Continuous power (@ 20° C): 1000 W Surge power (5 seconds): 2000 W Efficiency (Full Load): 88% Minimum DC Fuse Rating: 170A DC Input Current @ Nominal V DC Full Load 95A No Load 2.
17 Specifications (Hard wired Models) HARDWIRED MODELS: APSINT1524 APSINT2012 Weight: 12.7 Kg 17.1 Kg INVERTER Continuous power (@ 20° C): 1500 W 2000 W Surge power (5 seconds): 3000 W 4000 W Efficiency (Full Load): 89% 87% Minimum DC Fuse Rating: 90A 370A DC Input Current @ Nominal V DC Full Load 70A 192 A No Load 1.
36 OUTPUT/NEUTRA OUTPUT/HOT GROUND INPUT/NEUTRA INPUT/HOT “FOR USE WITH COPPER WIRE ONLY” Diagrams/Esquemas See “Configuration”, pg. 5. 1.1 is DIP Switch Group A. 1.2 is DIP Switch Group B . Refiérase a la sección “Configur ación”, página 22.
37 X/2 V olts X/2 V olts APS See Battery Connection, Pg. 9. 4.1 is the fuse. X = Y our APS’s In verter's Nominal Input V oltage. (See specs.) Refiérase a la sección “Cone xión de Baterías”, página 26. 4.1 representa el fusible. X = El V oltaje Nominal de Entrada del Inv ersor del APS.
38 APS 12V 12V Basic 12VDC Vehicular Battery Connection. See Pg. 9. 7.1 is the alternator. 7.2 is the vehicle battery ground. 7.3 is the vehicle battery . 7.4 is the fuse. Conexión Básica de Baterías de 12V de CD en Vehículos. Vea página 27. 7.1 representa el alternador.
39 1. Operating Mode Switch (All models) 2. DIP Switch Group A (All models) 3. DIP Switch Group B (Select models only) 4. “LINE” (All models) 5. “INV” (In ve r ting—all models) 6. “LOAD” (All models) 8. “BA TTER Y HI/MED/LO” (All models) 9.
40 OUTPUT/NEUTRA OUTPUT/HOT GROUND INPUT/NEUTRA INPUT/HOT “FOR USE WITH COPPER WIRE ONL Y” Diagrams/Esquemas 9b 1. Operating Mode Switch (All models) 2. DIP Switch Group A (All models) 3. DIP Switch Group B (Select models only) 4. “LINE” (All models) 5.
デバイスTripp Lite 93-2007 (200106010)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Tripp Lite 93-2007 (200106010)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTripp Lite 93-2007 (200106010)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tripp Lite 93-2007 (200106010)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tripp Lite 93-2007 (200106010)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tripp Lite 93-2007 (200106010)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTripp Lite 93-2007 (200106010)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tripp Lite 93-2007 (200106010)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTripp Lite 93-2007 (200106010)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
