Troy-Biltメーカー42052の使用説明書/サービス説明書
ページ先へ移動 of 32
Models 42051 - 9.5 HP / 26" Auger 42052 - 11 HP / 30" Auger OWNER’S MANUAL Snow Thrower • Safety • Assembly • Features and Controls • Operation • Maintenance • Parts List ® GA.
T able of Contents SECTION 1: SAFETY ........................................... 3 Safety Decals ......................................................................... 5 SECTION 2: ASSEMBLY ....................................... 6 Inspect Unit ...
SP ARK ARRESTER WARNING TO RESIDENTS OF CALIFORNIA AND SEVERAL OTHER ST A TES Under California law, and under the laws of several other states, you are not permitted to operate an internal combustion .
Section 1 : Safety 4 b. The 120V A.C. starter is equipped with a three-wire power cord and plug and is designed to operate on 120V A.C. household current. The starter must be properly grounded at all times to avoid the possibility of injury or death from electrical shock.
5 Section 1 : Safety 22. Be extremely careful when operating on or crossing gravel drives, walks or roads. Stay alert for hidden hazards or traffic. Remove any hearing protection. 23. Do not overload the machine capacity by attempting to clear snow at too fast a rate.
NOTE: Left and right sides of the unit are determined from the operator position, facing the direction of forward travel. A. Inspect Unit Inspect the unit and shipping crate for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage.
Section 2: Assembly D. Install Handlebars 1. Use the four 3/8-16 x 3/4" hex flange screws to attach the handlebars to the sides of the chassis. a. Install a screw in the upper mount- ing hole (C, Figure 2-3) on each side. Leave screws loose enough to allow handlebar to pivot.
8 Section 2: Assembly 6. Remove the washer and locknut from the screw (M, Figure 2-4) in the worm gear assembly (L). Position the worm gear assembly on the mounting bracket as follows: a. Engage the worm gear threads 1/2- way with the teeth on the flange of the discharge chute base (rotate chute as needed).
9 Section 2: Assembly Figure 2-6 Y Figure 2-7 AH AC AD AB AA AT AS AG R AF AE Figure 2-5 Z T U S V W U S AA X Figure 2-8 AF AB.
Section 2: Assembly J. Connect Wiring for Handlebar Warmers and Light 1. Gently unwind the electrical wiring har- ness (A, Figure 2-9) from its shipping position and route it back toward the right-side handlebar. 2. Without over-stretching the wiring har- ness, loop it up and around the handle- bar as shown in Figure 2-9.
IMPORTANT: Refer to the separate Engine Owner ’ s Manual for detailed information about the controls on the engine. Wheel Drive Control Lever (A, Fig. 3-1) This lever controls the engagement of the wheel drive. When the lever is down against the handlebar and the engine is run- ning, the wheels will rotate.
PRE-OPERA TION CHECKLIST Perform the following checks with the engine stopped and the spark plug wire disconnected from the spark plug. 1. Review Section 1: Safety and Section 3: Features and Controls in this manual. 2. Check for loose or missing hardware.
Section 4: Operation 7. Push the Primer Button (O, Figure 4-2) three times (cover hole in center of bulb when pushing). 8. To start engine with recoil starter: a. Before pulling recoil starter (N, Figure 4-2), be sure there are no obstacles behind you.
AUGER DRIVE ENGAGEMENT 1. Remove any debris from inside the collector (auger/impeller) housing. 2. Adjust the discharge chute deflector cap (D, Figure 4-3) angle with adjust- ment lever. The deflector cap should usually be adjusted to a low angle, so it is not pointing at any persons, ani- mals, buildings or vehicle, especially in windy conditions.
SNOW THROWING P A TTERNS Use the snow clearing pattern shown in Figure 4-4 when snow can only be thrown to one side. Begin throwing snow closest to the side opposite where it can be thrown and direct the discharge away from that side.
ENGINE MAINTENANCE IMPORTANT: Refer to the Engine Owner ’ s Manual for complete engine maintenance information. Engine Oil • Check the engine oil level each time be- fore starting the unit and after each 5 hours of operation. With the engine on level ground, the oil level should be at the “ FULL ” mark on the dipstick.
Section 5: Maintenance 4. Squeeze wheel drive control lever (X, Figure 5-1) against handlebar. Measure between the coiled ends of the stretched spring (W, Figure 5-4), making sure you measure between the same coils used in step 3. The spring length should now measure 1/2" (13mm) longer than the measurement taken in step 3.
AUGER DRIVE BEL T AND WHEEL DRIVE BEL T REPLACEMENT NOTE: The auger drive belt (there is one auger drive belt on the 9.5HP model and two auger drive belts on the 11HP model) must be removed before removing the wheel drive belt. The illustration (Figure 5- 6) shows two auger drive belts (AD), ig- nore the second belt if the unit is not so equipped.
19 The spring length should now measure 9/16" – 11/16" (14 – 17mm) longer than the measurement taken in Step 4. If it does not, loosen the jam nut (AM, Figure 5-8) and turn the adjuster (AN) to increase or decrease the length of the spring.
Section 5: Maintenance To adjust brake arm: 1. With engine stopped and spark plug wire disconnected, remove screws and washers (AB, Figure 5-1) and remove belt cover from unit. 2. Squeeze the auger drive control lever (AL, Figure 5-7) against handlebar.
21 Section 5: Maintenance POSSIBLE PROBLEM 1. Choke knob in incorrect position 2. Engine throttle lever in incorrect start- ing position 3. Engine not primed enough (when cold) 4. Engine primed too much (when cold) 5. Spark plug wire disconnected 6. Fouled or faulty spark plug 7.
22 TROUBLE Auger drive control lever does not engage auger drive Auger spins with drive lever disengaged Wheel drive control lever does not turn wheels Wheels turn with wheel drive control lever disen.
23 Section 5: Maintenance REQUIRED MAINTENANCE SCHEDULE This table describes service guidelines only and does not provide complete service information.
24 Specifications, Optional Kits and Accessories SPECIFICA TIONS/OPTIONAL KITS AND ACCESSORIES Specifications Below is a list of specifications for your snow thrower. The information is the most current at the time this manual was printed. Kit Description Tire Chain Kit .
25 Parts List Models 42051 & 42052 5 19 1 2 3 4 3 92 2 22 8 14 15 16 20 25 6 24 17 27 7 26 15 14 8 23 18 12 12 11 12 12 13 13 13 13 1 1185224 Oil Seal .........................................................1 2 1185374 Needle Bearing ............
DRA WING NO. 2 Parts List Models 42051 & 42052 26 84 68 111 20 33 11 25 100 96 39 100 26 30 7 56 56 97 49 40 50 50 97 49 10 7 5 112 22 22 21 76 58 57 57 55 4 62 19 36 18 17 78 79 63 49 32 41 81 38.
1 1745576 Handle Grip .................................................. 2 3 1739937 Idler Arm ..................................................... 1 4 1733398 Lock Nut, 3/8 – 16 ......................................... 3 5 1734398 Lock Nut, 1/4 – 20 .
28 Parts List Models 42051 & 42052 76 74 74 8 5 64 80 64 80 73 73 18 19 33 18 19 32 52 26 46 17 82 27 30 25 25 111 56 54 55 1 59 51 86 85 44 112 112 112 17 17 23 3 21 28 21 108 25 28 2 24 6 57 12 .
29 1 1100045 Hex Hd. Screw, 5/16 – 18 x 1 ............................ 3 2 * Briggs & Stratton Engine ................................. 1 3 1745485 Control Arm ..................................................... 1 4 1100242 Lock Washer, 5/16 .
30 Parts List Models 42051 & 42052 69 2 3 70 22 56 4 51 47 47 57 57 62 22 7 7 56 56 9 52 13 9 7 62 11 12 1 15 16 6 63 17 58 73 19 68 68 60 71 58 14 58 50 48 49 66 47 43 44 42 74 58 59 46 64 14 17 58 35 35 34 36 41 40 39 38 37 30 67 53 54 5 76 4 4 32 32 20 21 45 10 33 29 58 27 27 26 31 29 29 29 26 65 25 24 23 72 28 61 18 DRA WING NO.
31 1 1186329 Flange Bolt, 5/16 – 18 x 3/4 ........................... 1 2 1185403 Retainer, 3/8 ................................................ 1 3 1757843 Knob ............................................................ 1 4 1107383 Flat Washer, 3/8 .
1905666 Rev. A (6/01) Printed in U.S.A. © 2001 Garden Way Incorporated CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory so that we can provide you with warranty benefits and in- formational bulletins.
デバイスTroy-Bilt 42052の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 42052をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 42052の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 42052の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 42052で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 42052を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 42052の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 42052に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 42052デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
